| Age | Commit message (Collapse) | Author |
|---|
|
HW can have different input/output delays for each of the pins.
Currently, only E82X adapters have delay compensation based on TSPLL
config and E810 adapters have constant 1 ms compensation, both cases
only for output delays and the same one for all pins.
E825 adapters have different delays for SDP and other pins. Those
delays are also based on direction and input delays are different than
output ones. This is the main reason for moving delays to pin
description structure.
Add a field in ice_ptp_pin_desc structure to reflect that. Delay values
are based on approximate calculations of HW delays based on HW spec.
Implement external timestamp (input) delay compensation.
Remove existing definitions and wrappers for periodic output propagation
delays.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Programming the PHY registers in preparation for an increment value change
or a timer adjustment on E810 requires issuing Admin Queue commands for
each PHY register. It has been found that the firmware Admin Queue
processing occasionally has delays of tens or rarely up to hundreds of
milliseconds. This delay cascades to failures in the PTP applications which
depend on these updates being low latency.
Consider a standard PTP profile with a sync rate of 16 times per second.
This means there is ~62 milliseconds between sync messages. A complete
cycle of the PTP algorithm
1) Sync message (with Tx timestamp) from source
2) Follow-up message from source
3) Delay request (with Tx timestamp) from sink
4) Delay response (with Rx timestamp of request) from source
5) measure instantaneous clock offset
6) request time adjustment via CLOCK_ADJTIME systemcall
The Tx timestamps have a default maximum timeout of 10 milliseconds. If we
assume that the maximum possible time is used, this leaves us with ~42
milliseconds of processing time for a complete cycle.
The CLOCK_ADJTIME system call is synchronous and will block until the
driver completes its timer adjustment or frequency change.
If the writes to prepare the PHY timers get hit by a latency spike of 50
milliseconds, then the PTP application will be delayed past the point where
the next cycle should start. Packets from the next cycle may have already
arrived and are waiting on the socket.
In particular, LinuxPTP ptp4l may start complaining about missing an
announce message from the source, triggering a fault. In addition, the
clockcheck logic it uses may trigger. This clockcheck failure occurs
because the timestamp captured by hardware is compared against a reading of
CLOCK_MONOTONIC. It is assumed that the time when the Rx timestamp is
captured and the read from CLOCK_MONOTONIC are relatively close together.
This is not the case if there is a significant delay to processing the Rx
packet.
Newer firmware supports programming the PHY registers over a low latency
interface which bypasses the Admin Queue. Instead, software writes to the
REG_LL_PROXY_L and REG_LL_PROXY_H registers. Firmware reads these registers
and then programs the PHY timers.
Implement functions to use this interface when available to program the PHY
timers instead of using the Admin Queue. This avoids the Admin Queue
latency and ensures that adjustments happen within acceptable latency
bounds.
Co-developed-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Anton Nadezhdin <anton.nadezhdin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Newer versions of firmware support programming the PHY timer via the low
latency interface exposed over REG_LL_PROXY_L and REG_LL_PROXY_H. Add
support for checking the device capabilities for this feature.
Co-developed-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Milena Olech <milena.olech@intel.com>
Signed-off-by: Anton Nadezhdin <anton.nadezhdin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Newer firmware for the E810 devices support a 'low latency' interface to
interact with the PHY without using the Admin Queue. This is interacted
with via the REG_LL_PROXY_L and REG_LL_PROXY_H registers.
Currently, this interface is only used for Tx timestamps. There are two
different mechanisms, including one which uses an interrupt for firmware to
signal completion. However, these two methods are mutually exclusive, so no
synchronization between them was necessary.
This low latency interface is being extended in future firmware to support
also programming the PHY timers. Use of the interface for PHY timers will
need synchronization to ensure there is no overlap with a Tx timestamp.
The interrupt-based response complicates the locking somewhat. We can't use
a simple spinlock. This would require being acquired in
ice_ptp_req_tx_single_tstamp, and released in
ice_ptp_complete_tx_single_tstamp. The ice_ptp_req_tx_single_tstamp
function is called from the threaded IRQ, and the
ice_ptp_complete_tx_single_stamp is called from the low latency IRQ, so we
would need to acquire the lock with IRQs disabled.
To handle this, we'll use a wait queue along with
wait_event_interruptible_locked_irq in the update flows which don't use the
interrupt.
The interrupt flow will acquire the wait queue lock, set the
ATQBAL_FLAGS_INTR_IN_PROGRESS, and then initiate the firmware low latency
request, and unlock the wait queue lock.
Upon receipt of the low latency interrupt, the lock will be acquired, the
ATQBAL_FLAGS_INTR_IN_PROGRESS bit will be cleared, and the firmware
response will be captured, and wake_up_locked() will be called on the wait
queue.
The other flows will use wait_event_interruptible_locked_irq() to wait
until the ATQBAL_FLAGS_INTR_IN_PROGRESS is clear. This function checks the
condition under lock, but does not hold the lock while waiting. On return,
the lock is held, and a return of zero indicates we hold the lock and the
in-progress flag is not set.
This will ensure that threads which need to use the low latency interface
will sleep until they can acquire the lock without any pending low latency
interrupt flow interfering.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Milena Olech <milena.olech@intel.com>
Signed-off-by: Anton Nadezhdin <anton.nadezhdin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The TS_LL_READ macros are used as part of the low latency Tx timestamp
interface. A future firmware extension will add support for performing PHY
timer updates over this interface. Using TS_LL_READ as the prefix for these
macros will be confusing once the interface is used for other purposes.
Rename the macros, using the prefix REG_LL_PROXY_H, to better clarify that
this is for the low latency interface.
Additionally add macros for PF_SB_ATQBAH and PF_SB_ATQBAL registers to
better clarify content of this registers as PF_SB_ATQBAH contain low
part of Tx timestamp
Co-developed-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Milena Olech <milena.olech@intel.com>
Signed-off-by: Anton Nadezhdin <anton.nadezhdin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The ice_read_phy_tstamp_ll_e810 function repeatedly reads the PF_SB_ATQBAL
register until the TS_LL_READ_TS bit is cleared. This is a perfect
candidate for using rd32_poll_timeout. However, the default implementation
uses a sleep-based wait. Use read_poll_timeout_atomic macro which is based
on the non-sleeping implementation and use it to replace the loop reading
in the ice_read_phy_tstamp_ll_e810 function.
Co-developed-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Anton Nadezhdin <anton.nadezhdin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Use string choice helpers for better readability.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Julia Lawall <julia.lawall@inria.fr>
Closes: https://lore.kernel.org/r/202410121553.SRNFzc2M-lkp@intel.com/
Signed-off-by: R Sundar <prosunofficial@gmail.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Firmware generates events for global events or port specific events.
Driver shall subscribe for health status events from firmware on supported
FW versions >= 1.7.6.
Driver shall expose those under specific health reporter, two new
reporters are introduced:
- FW health reporter shall represent global events (problems with the
image, recovery mode);
- Port health reporter shall represent port-specific events (module
failure).
Firmware only reports problems when those are detected, it does not store
active fault list.
Driver will hold only last global and last port-specific event.
Driver will report all events via devlink health report,
so in case of multiple events of the same source they can be reviewed
using devlink autodump feature.
$ devlink health
pci/0000:b1:00.3:
reporter fw
state healthy error 0 recover 0 auto_dump true
reporter port
state error error 1 recover 0 last_dump_date 2024-03-17
last_dump_time 09:29:29 auto_dump true
$ devlink health diagnose pci/0000:b1:00.3 reporter port
Syndrome: 262
Description: Module is not present.
Possible Solution: Check that the module is inserted correctly.
Port Number: 0
Tested on Intel Corporation Ethernet Controller E810-C for SFP
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Co-developed-by: Sharon Haroni <sharon.haroni@intel.com>
Signed-off-by: Sharon Haroni <sharon.haroni@intel.com>
Co-developed-by: Nicholas Nunley <nicholas.d.nunley@intel.com>
Signed-off-by: Nicholas Nunley <nicholas.d.nunley@intel.com>
Co-developed-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Konrad Knitter <konrad.knitter@intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The new recipe should be added even if exactly the same recipe already
exists with different priority.
Example use case is when the rule is being added from TC tool context.
It should has the highest priority, but if the recipe already exists
the rule will inherit it priority. It can lead to the situation when
the rule added from TC tool has lower priority than expected.
The solution is to check the recipe priority when trying to find
existing one.
Previous recipe is still useful. Example:
RID 8 -> priority 4
RID 10 -> priority 7
The difference is only in priority rest is let's say eth + mac +
direction.
Adding ARP + MAC_A + RX on RID 8, forward to VF0_VSI
After that IP + MAC_B + RX on RID 10 (from TC tool), forward to PF0
Both will work.
In case of adding ARP + MAC_A + RX on RID 8, forward to VF0_VSI
ARP + MAC_A + RX on RID 10, forward to PF0.
Only second one will match, but this is expected.
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Move ice_adapter initialization to be after HW init, so it could use HW
capabilities, like number of PFs. This is needed for devlink-resource
based RSS LUT size management for PF/VF (not in this series).
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Clean up goto labels after previous commit, to conform to single naming
scheme in ice_probe() and ice_init_dev().
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Split ice_init_hw() call out from ice_init_dev(). Such move enables
pulling the former to be even earlier on call path, what would enable
moving ice_adapter init to be between the two (in subsequent commit).
Such move enables ice_adapter to know about number of PFs.
Do the same for ice_deinit_hw(), so the init and deinit calls could
be easily mirrored.
Next commit will rename unrelated goto labels to unroll prefix.
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Move call to ice_wait_for_fw() from ice_init_dev() into ice_init_hw(),
where it fits better. This requires also to move ice_wait_for_fw()
to ice_common.c.
ice_is_pf_c827() is now used only in ice_common.c, so it could be static.
CC: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Per previous change downgrade all NIC drivers (discrete, embedded,
SoC components, virtual) which don't report test results to CI
from Supported to Maintained.
Also include all components or building blocks of NIC drivers
(separate entries for "shared" code, subsystem support like PTP
or entries for specific offloads etc.)
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Link: https://patch.msgid.link/20250111024359.3678956-2-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As announced back in April, require running upstream tests
to maintain Supported status for NIC drivers:
https://lore.kernel.org/20240425114200.3effe773@kernel.org
Multiple vendors have been "working on it" for months.
Let's make it official.
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250111024359.3678956-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The FRED RSP0 MSR is only used for delivering events when running
userspace. Linux leverages this property to reduce expensive MSR
writes and optimize context switches. The kernel only writes the
MSR when about to run userspace *and* when the MSR has actually
changed since the last time userspace ran.
This optimization is implemented by maintaining a per-CPU cache of
FRED RSP0 and then checking that against the value for the top of
current task stack before running userspace.
However cpu_init_fred_exceptions() writes the MSR without updating
the per-CPU cache. This means that the kernel might return to
userspace with MSR_IA32_FRED_RSP0==0 when it needed to point to the
top of current task stack. This would induce a double fault (#DF),
which is bad.
A context switch after cpu_init_fred_exceptions() can paper over
the issue since it updates the cached value. That evidently
happens most of the time explaining how this bug got through.
Fix the bug through resynchronizing the FRED RSP0 MSR with its
per-CPU cache in cpu_init_fred_exceptions().
Fixes: fe85ee391966 ("x86/entry: Set FRED RSP0 on return to userspace instead of context switch")
Signed-off-by: Xin Li (Intel) <xin@zytor.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc:stable@vger.kernel.org
Link: https://lore.kernel.org/all/20250110174639.1250829-1-xin%40zytor.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull seccomp fix from Kees Cook:
"Fix a randconfig failure:
- Unconditionally define stub for !CONFIG_SECCOMP (Linus Walleij)"
* tag 'seccomp-v6.13-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
seccomp: Stub for !CONFIG_SECCOMP
|
|
Use KVM or HVF if supported by the QEMU binary and available on the
system.
This produces a nice improvement on my Apple M3 Pro running macOS 14.7:
Before:
./tools/testing/kunit/kunit.py exec --arch arm64
[HH:MM:SS] Elapsed time: 10.145s
After:
./tools/testing/kunit/kunit.py exec --arch arm64
[HH:MM:SS] Elapsed time: 1.773s
Signed-off-by: Tamir Duberstein <tamird@gmail.com>
Reviewed-by: David Gow <davidgow@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
|
|
Python 3.13 added os.process_cpu_count as a cross-platform alternative
for the Linux-only os.sched_getaffinity. Use it when it's available and
provide a fallback when it's not.
This allows kunit to run on macOS.
Signed-off-by: Tamir Duberstein <tamird@gmail.com>
Reviewed-by: David Gow <davidgow@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
|
|
Remove hard-coded strings by using the str_off_on() helper.
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Link: https://lore.kernel.org/r/20241202154603.1193-2-thorsten.blum@linux.dev
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Replace ternary (condition ? "enable" : "disable") syntax with helpers
from string_choices.h because:
1. Simple function call with one argument is easier to read. Ternary
operator has three arguments and with wrapping might lead to quite
long code.
2. Is slightly shorter thus also easier to read.
3. It brings uniformity in the text - same string.
4. Allows deduping by the linker, which results in a smaller binary
file.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250114192701.912430-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Fix E825 initialization
Grzegorz Nitka says:
E825 products have incorrect initialization procedure, which may lead to
initialization failures and register values.
Fix E825 products initialization by adding correct sync delay, checking
the PHY revision only for current PHY and adding proper destination
device when reading port/quad.
In addition, E825 uses PF ID for indexing per PF registers and as
a primary PHY lane number, which is incorrect.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: Add correct PHY lane assignment
ice: Fix ETH56G FC-FEC Rx offset value
ice: Fix quad registers read on E825
ice: Fix E825 initialization
====================
Link: https://patch.msgid.link/20250113182840.3564250-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Matthieu Baerts says:
====================
mptcp: fixes for connect selftest flakes
Last week, Jakub reported [1] that the MPTCP Connect selftest was
unstable. It looked like it started after the introduction of some fixes
[2]. After analysis from Paolo, these patches revealed existing bugs,
that should be fixed by the following patches.
- Patch 1: Make sure ACK are sent when MPTCP-level window re-opens. In
some corner cases, the other peer was not notified when more data
could be sent. A fix for v5.11, but depending on a feature introduced
in v5.19.
- Patch 2: Fix spurious wake-up under memory pressure. In this
situation, the userspace could be invited to read data not being there
yet. A fix for v6.7.
- Patch 3: Fix a false positive error when running the MPTCP Connect
selftest with the "disconnect" cases. The userspace could disconnect
the socket too soon, which would reset (MP_FASTCLOSE) the connection,
interpreted as an error by the test. A fix for v5.17.
Link: https://lore.kernel.org/20250107131845.5e5de3c5@kernel.org [1]
Link: https://lore.kernel.org/20241230-net-mptcp-rbuf-fixes-v1-0-8608af434ceb@kernel.org [2]
====================
Link: https://patch.msgid.link/20250113-net-mptcp-connect-st-flakes-v1-0-0d986ee7b1b6@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The disconnect test-case generates spurious errors:
INFO: disconnect
INFO: extra options: -I 3 -i /tmp/tmp.r43niviyoI
01 ns1 MPTCP -> ns1 (10.0.1.1:10000 ) MPTCP (duration 140ms) [FAIL]
file received by server does not match (in, out):
Unexpected revents: POLLERR/POLLNVAL(19)
-rw-r--r-- 1 root root 10028676 Jan 10 10:47 /tmp/tmp.r43niviyoI.disconnect
Trailing bytes are:
��\����R���!8��u2��5N%
-rw------- 1 root root 9992290 Jan 10 10:47 /tmp/tmp.Os4UbnWbI1
Trailing bytes are:
��\����R���!8��u2��5N%
02 ns1 MPTCP -> ns1 (dead:beef:1::1:10001) MPTCP (duration 206ms) [ OK ]
03 ns1 MPTCP -> ns1 (dead:beef:1::1:10002) TCP (duration 31ms) [ OK ]
04 ns1 TCP -> ns1 (dead:beef:1::1:10003) MPTCP (duration 26ms) [ OK ]
[FAIL] Tests of the full disconnection have failed
Time: 2 seconds
The root cause is actually in the user-space bits: the test program
currently disconnects as soon as all the pending data has been spooled,
generating an FASTCLOSE. If such option reaches the peer before the
latter has reached the closed status, the msk socket will report an
error to the user-space, as per protocol specification, causing the
above failure.
Address the issue explicitly waiting for all the relevant sockets to
reach a closed status before performing the disconnect.
Fixes: 05be5e273c84 ("selftests: mptcp: add disconnect tests")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250113-net-mptcp-connect-st-flakes-v1-3-0d986ee7b1b6@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The wake-up condition currently implemented by mptcp_epollin_ready()
is wrong, as it could mark the MPTCP socket as readable even when
no data are present and the system is under memory pressure.
Explicitly check for some data being available in the receive queue.
Fixes: 5684ab1a0eff ("mptcp: give rcvlowat some love")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250113-net-mptcp-connect-st-flakes-v1-2-0d986ee7b1b6@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
mptcp_cleanup_rbuf() is responsible to send acks when the user-space
reads enough data to update the receive windows significantly.
It tries hard to avoid acquiring the subflow sockets locks by checking
conditions similar to the ones implemented at the TCP level.
To avoid too much code duplication - the MPTCP protocol can't reuse the
TCP helpers as part of the relevant status is maintained into the msk
socket - and multiple costly window size computation, mptcp_cleanup_rbuf
uses a rough estimate for the most recently advertised window size:
the MPTCP receive free space, as recorded as at last-ack time.
Unfortunately the above does not allow mptcp_cleanup_rbuf() to detect
a zero to non-zero win change in some corner cases, skipping the
tcp_cleanup_rbuf call and leaving the peer stuck.
After commit ea66758c1795 ("tcp: allow MPTCP to update the announced
window"), MPTCP has actually cheap access to the announced window value.
Use it in mptcp_cleanup_rbuf() for a more accurate ack generation.
Fixes: e3859603ba13 ("mptcp: better msk receive window updates")
Cc: stable@vger.kernel.org
Reported-by: Jakub Kicinski <kuba@kernel.org>
Closes: https://lore.kernel.org/20250107131845.5e5de3c5@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250113-net-mptcp-connect-st-flakes-v1-1-0d986ee7b1b6@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A Broadcast Sink might require BIG sync to be terminated and
re-established multiple times, while keeping the same PA sync
handle active. This can be possible if the configuration of the
listening (PA sync) socket is reset once all bound BISes are
established and accepted by the user space:
1. The DEFER setup flag needs to be reset on the parent socket,
to allow another BIG create sync procedure to be started on socket
read.
2. The BT_SK_BIG_SYNC flag needs to be cleared on the parent socket,
to allow another BIG create sync command to be sent.
3. The socket state needs to transition from BT_LISTEN to BT_CONNECTED,
to mark that the listening process has completed and another one can
be started if needed.
Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Eric Dumazet says:
====================
tcp: add a new PAWS_ACK drop reason
Current TCP_RFC7323_PAWS drop reason is too generic and can
cause confusion.
One common source for these drops are ACK packets coming too late.
A prior packet with payload already changed tp->rcv_nxt.
Add TCP_RFC7323_PAWS_ACK new drop reason, and do not
generate a DUPACK for such old ACK.
====================
Link: https://patch.msgid.link/20250113135558.3180360-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Prior patch in the series added TCP_RFC7323_PAWS_ACK drop reason.
This patch adds the corresponding SNMP counter, for folks
using nstat instead of tracing for TCP diagnostics.
nstat -az | grep PAWSOldAck
Suggested-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Jason Xing <kerneljasonxing@gmail.com>
Tested-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://patch.msgid.link/20250113135558.3180360-4-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
XPS can cause reorders because of the relaxed OOO
conditions for pure ACK packets.
For hosts not using RFS, what can happpen is that ACK
packets are sent on behalf of the cpu processing NIC
interrupts, selecting TX queue A for ACK packet P1.
Then a subsequent sendmsg() can run on another cpu.
TX queue selection uses the socket hash and can choose
another queue B for packets P2 (with payload).
If queue A is more congested than queue B,
the ACK packet P1 could be sent on the wire after
P2.
A linux receiver when processing P1 (after P2) currently increments
LINUX_MIB_PAWSESTABREJECTED (TcpExtPAWSEstab)
and use TCP_RFC7323_PAWS drop reason.
It might also send a DUPACK if not rate limited.
In order to better understand this pattern, this
patch adds a new drop_reason : TCP_RFC7323_PAWS_ACK.
For old ACKS like these, we no longer increment
LINUX_MIB_PAWSESTABREJECTED and no longer sends a DUPACK,
keeping credit for other more interesting DUPACK.
perf record -e skb:kfree_skb -a
perf script
...
swapper 0 [148] 27475.438637: skb:kfree_skb: ... location=tcp_validate_incoming+0x4f0 reason: TCP_RFC7323_PAWS_ACK
swapper 0 [208] 27475.438706: skb:kfree_skb: ... location=tcp_validate_incoming+0x4f0 reason: TCP_RFC7323_PAWS_ACK
swapper 0 [208] 27475.438908: skb:kfree_skb: ... location=tcp_validate_incoming+0x4f0 reason: TCP_RFC7323_PAWS_ACK
swapper 0 [148] 27475.439010: skb:kfree_skb: ... location=tcp_validate_incoming+0x4f0 reason: TCP_RFC7323_PAWS_ACK
swapper 0 [148] 27475.439214: skb:kfree_skb: ... location=tcp_validate_incoming+0x4f0 reason: TCP_RFC7323_PAWS_ACK
swapper 0 [208] 27475.439286: skb:kfree_skb: ... location=tcp_validate_incoming+0x4f0 reason: TCP_RFC7323_PAWS_ACK
...
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Jason Xing <kerneljasonxing@gmail.com>
Link: https://patch.msgid.link/20250113135558.3180360-3-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Following patch is adding a new drop_reason to tcp_validate_incoming().
Change tcp_disordered_ack() to not return a boolean anymore,
but a drop reason.
Change its name to tcp_disordered_ack_check()
Refactor tcp_validate_incoming() to ease the code
review of the following patch, and reduce indentation
level.
This patch is a refactor, with no functional change.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Jason Xing <kerneljasonxing@gmail.com>
Link: https://patch.msgid.link/20250113135558.3180360-2-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There is a typo in a phydev_err message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250113091555.23594-1-colin.i.king@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, an interface is created in the driver during channel assignment.
If mac80211 attempts to set a key for an interface before this assignment,
the driver caches the key. Once the interface is created, the driver
installs the cached key to the hardware. This sequence is exemplified in
mesh mode operation where the group key is set before channel assignment.
However, in ath12k_mac_update_key_cache(), after caching the key, due to
incorrect logic, it is deleted from the cache during the subsequent loop
iteration. As a result, after the interface is created, the driver does not
find any cached key, and the key is not installed to the hardware which is
wrong. This leads to issue in mesh, where broadcast traffic is not
encrypted over the air.
Fix this issue by adjusting the logic of ath12k_mac_update_key_cache()
properly.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3-03253.1-QCAHKSWPL_SILICONZ-29 # Nicolas Escande <nico.escande@gmail.com>
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 # Nicolas Escande <nico.escande@gmail.com>
Fixes: 25e18b9d6b4b ("wifi: ath12k: modify ath12k_mac_op_set_key() for MLO")
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Tested-by: Nicolas Escande <nico.escande@gmail.com>
Link: https://patch.msgid.link/20250112-fix_key_cache_handling-v2-1-70e142c6153e@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
function
Currently, the uninitialized variable 'ab' is accessed in the
ath12k_mac_allocate() function. Initialize 'ab' with the first radio device
present in the hardware abstraction handle (ah). Additionally, move the
default setting procedure from the pdev mapping iteration to the total
radio calculating iteration for better code readability. Perform the
maximum radio validation check for total_radio to ensure that both num_hw
and radio_per_hw are validated indirectly, as these variables are derived
from total_radio. This also fixes the below Smatch static checker warning.
Smatch warning:
ath12k_mac_allocate() error: uninitialized symbol 'ab'
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Fixes: a343d97f27f5 ("wifi: ath12k: move struct ath12k_hw from per device to group")
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20250112071630.4059410-5-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Currently, the ath12k_get_num_hw() helper function takes the device handle
as an argument. Here, the number of hardware is retrieved from the group
handle. Demanding the device handle from the caller is unnecessary since
in some cases the group handle is already available. Additionally, there
is no longer a need for multiple indirections to get the number of
hardware. Therefore, remove this helper function and directly use
ag->num_hw. This change also fixes the below Smatch static checker
warning.
Smatch warning:
ath12k_mac_destroy() error: we previously assumed 'ab' could be null
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/ath12k/3e705de0-67d1-4437-97ff-4828d83ae2af@stanley.mountain/
Closes: https://scan7.scan.coverity.com/#/project-view/52682/11354?selectedIssue=1602340
Fixes: a343d97f27f5 ("wifi: ath12k: move struct ath12k_hw from per device to group")
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Acked-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Link: https://patch.msgid.link/20250112071630.4059410-4-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Currently, ath12k_hw is placed inside the ath12k_hw_group. However, the
ath12k_hw get helper function takes the device handle and the index as
parameters. Here, the index parameter is specific to the group handle.
Therefore, change this helper function argument from the device handle
to the group handle.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20250112071630.4059410-3-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Currently, ath12k_hw is placed inside the ath12k_hw_group. However, the
ath12k_hw set helper function takes the device handle and the index as
parameters. Here, the index parameter is specific to the group handle.
Therefore, change this helper function argument from the device handle to
the group handle.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20250112071630.4059410-2-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
After a job completes, the corresponding pointer in the device must
be set to NULL. Failing to do so triggers a warning when unloading
the driver, as it appears the job is still active. To prevent this,
assign the job pointer to NULL after completing the job, indicating
the job has finished.
Fixes: 14d1d1908696 ("drm/v3d: Remove the bad signaled() implementation.")
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Reviewed-by: Jose Maria Casanova Crespo <jmcasanova@igalia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250113154741.67520-1-mcanal@igalia.com
|
|
Allow configuring the DPM watchdog to warn about slow suspend/resume
functions without causing a system panic(). This allows you to set the
DPM_WATCHDOG_WARNING_TIMEOUT to something like 5 or 10 seconds to get
warnings about slow suspend/resume functions that eventually succeed.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Link: https://patch.msgid.link/20250109125957.v2.1.I4554f931b8da97948f308ecc651b124338ee9603@changeid
[ rjw: Subject edit ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Modify a non-kernel-doc comment to begin with /* instead of /**
so that it does not cause a kernel-doc warning.
power.h:114: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Auxiliary structure used for reading the snapshot image data and
power.h:114: warning: missing initial short description on line:
* Auxiliary structure used for reading the snapshot image data and
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Link: https://patch.msgid.link/20250111063107.910825-1-rdunlap@infradead.org
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Commit 3c55e94c0ade ("cpufreq: ACPI: Extend frequency tables to cover
boost frequencies") introduced an assumption in acpi_cpufreq_cpu_init()
that the first entry in the P-state table was the nominal frequency.
This assumption is incorrect. The frequency corresponding to the P0
P-State need not be the same as the nominal frequency advertised via
CPPC.
Since the driver is using the CPPC.highest_perf and CPPC.nominal_perf
to compute the boost-ratio, it makes sense to use CPPC.nominal_freq to
compute the max-frequency. CPPC.nominal_freq is advertised on
platforms supporting CPPC revisions 3 or higher.
Hence, fallback to using the first entry in the P-State table only on
platforms that do not advertise CPPC.nominal_freq.
Fixes: 3c55e94c0ade ("cpufreq: ACPI: Extend frequency tables to cover boost frequencies")
Tested-by: Dhananjay Ugwekar <Dhananjay.Ugwekar@amd.com>
Signed-off-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://patch.msgid.link/20250113044107.566-1-gautham.shenoy@amd.com
[ rjw: Retain reverse X-mas tree ordering of local variable declarations ]
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
It is possible to enable few cpufreq drivers, without the framework
being enabled. This happened due to a bug while moving the entries
earlier. Fix it.
Fixes: 7ee1378736f0 ("cpufreq: Move CPPC configs to common Kconfig and add RISC-V")
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Pierre Gondois <pierre.gondois@arm.com>
Reviewed-by: Sunil V L <sunilvl@ventanamicro.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Link: https://patch.msgid.link/84ac7a8fa72a8fe20487bb0a350a758bce060965.1736488384.git.viresh.kumar@linaro.org
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci fix from Bjorn Helgaas:
- Prevent bwctrl NULL pointer dereference that caused hangs on shutdown
on ASUS ROG Strix SCAR 17 G733PYV (Lukas Wunner)
* tag 'pci-v6.13-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
PCI/bwctrl: Fix NULL pointer deref on unbind and bind
|
|
Since commit 02fb4f008433 ("clk: clk-loongson2: Fix potential buffer
overflow in flexible-array member access"), the clk provider register is
failed.
The count of `clks_num` is shown below:
for (p = data; p->name; p++)
clks_num++;
In fact, `clks_num` represents the number of SoC clocks and should be
expressed as the maximum value of the clock binding id in use (p->id + 1).
Now we fix it to avoid the following error when trying to register a clk
provider:
[ 13.409595] of_clk_hw_onecell_get: invalid index 17
Cc: stable@vger.kernel.org
Cc: Gustavo A. R. Silva <gustavoars@kernel.org>
Fixes: 02fb4f008433 ("clk: clk-loongson2: Fix potential buffer overflow in flexible-array member access")
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Link: https://lore.kernel.org/r/82e43d89a9a6791129cf8ea14f4eeb666cd87be4.1736856470.git.zhoubinbin@loongson.cn
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Since commit 706ae6446494 ("clk: fixed-rate: add
devm_clk_hw_register_fixed_rate_parent_data()"), we can use the
devm_clk_hw_register_fixed_rate_parent_data() helper and from then on
there is no need to manually unregister the fixed rate hw.
Since clk_hw_unregister_fixed_rate() was not called before, we also fix
the memory leak that was present.
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Link: https://lore.kernel.org/r/8733a7485619bdb791de25201a3d7984d1849c9f.1736856470.git.zhoubinbin@loongson.cn
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Tariq Toukan says:
====================
mlx5-next updates 2025-01-14
The following pull-request contains mlx5 IFC updates.
* 'mlx5-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
net/mlx5: Add nic_cap_reg and vhca_icm_ctrl registers
net/mlx5: SHAMPO: Introduce new SHAMPO specific HCA caps
net/mlx5: Add support for MRTCQ register
net/mlx5: Update mlx5_ifc to support FEC for 200G per lane link modes
====================
Link: https://patch.msgid.link/20250114055700.1928736-1-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Introduce num_reg to store the number of clocks, this helps to make
_clk_get become a common helper function which called jh71x0_clk_get().
With this, it helps to simplify the code and extend the code in the
future.
Signed-off-by: Changhuang Liang <changhuang.liang@starfivetech.com>
Link: https://lore.kernel.org/r/20250114081300.36600-1-changhuang.liang@starfivetech.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into clk-rockchip
Pull Rockchip clk driver updates from Heiko Stuebner:
Real handling of the linked clocks (clocks of the interconnect port a
peripheral is connected to) on rk3588 using pm-clocks, allowing us to
stop marking them as critical and one more rk3588 critical clock, that
the kernel cannot handle otherwise right now.
* tag 'v6.14-rockchip-clk1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
clk: rockchip: rk3588: make refclko25m_ethX critical
clk: rockchip: rk3588: drop RK3588_LINKED_CLK
clk: rockchip: implement linked gate clock support
clk: rockchip: expose rockchip_clk_set_lookup
clk: rockchip: rk3588: register GATE_LINK later
clk: rockchip: support clocks registered late
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"One iscsi driver fix and one core fix.
The core fix is an important one because a retry efficiency update is
now causing some USB devices to get the wrong size on discovery (it
upset their retry logic for READ_CAPACITY_16)"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: iscsi: Fix redundant response for ISCSI_UEVENT_GET_HOST_STATS request
scsi: core: Fix command pass through retry regression
|
|
Adds a new BO param that keeps the reservation locked after creation.
This removes the need to re-reserve the BO after creation which is a
waste of cycles.
This also fixes a bug in vmw_prime_import_sg_table where the imported
reservation is unlocked twice.
Signed-off-by: Ian Forbes <ian.forbes@broadcom.com>
Fixes: b32233acceff ("drm/vmwgfx: Fix prime import/export")
Reviewed-by: Zack Rusin <zack.rusin@broadcom.com>
Signed-off-by: Zack Rusin <zack.rusin@broadcom.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250110185335.15301-1-ian.forbes@broadcom.com
|
