| Age | Commit message (Collapse) | Author |
|---|
|
operation sanity check
To detect potential bugs in CAN protocol implementations (double removal of
receiver entries) a WARN() statement has been used if no matching list item was
found for removal.
The fault injection issued by syzkaller was able to create a situation where
the closing of a socket runs simultaneously to the notifier call chain for
removing the CAN network device in use.
This case is very unlikely in real life but it doesn't break anything.
Therefore we just replace the WARN() statement with pr_warn() to preserve the
notification for the CAN protocol development.
Reported-by: syzbot+381d06e0c8eaacb8706f@syzkaller.appspotmail.com
Reported-by: syzbot+d0ddd88c9a7432f041e6@syzkaller.appspotmail.com
Reported-by: syzbot+76d62d3b8162883c7d11@syzkaller.appspotmail.com
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/r/20201126192140.14350-1-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Add support for mcan bit timing and control mode according to bosch mcan IP
version 3.3.0. The mcan version read from the Core Release field of CREL
register would be 33. Accordingly the properties are to be set for mcan v3.3.0
Signed-off-by: Pankaj Sharma <pankj.sharma@samsung.com>
Link: https://lore.kernel.org/r/1606366302-5520-1-git-send-email-pankj.sharma@samsung.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
At lest the revision 3.3.0 of the bosch m_can IP core specifies that valid
register values for "Nominal Time segment after sample point (NTSEG2)" are from
1 to 127. As the hardware uses a value of one more than the programmed value,
mean tseg2_min is 2.
This patch fixes the tseg2_min value accordingly.
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Mario Huettel <mario.huettel@gmx.net>
Acked-by: Sriram Dash <sriram.dash@samsung.com>
Link: https://lore.kernel.org/r/20201124190751.3972238-1-mkl@pengutronix.de
Fixes: b03cfc5bb0e1 ("can: m_can: Enable M_CAN version dependent initialization")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
request_threaded_irq()'s flags
The threaded IRQ handler is used for the tcan4x5x driver only. The IRQ pin of
the tcan4x5x controller is active low, so better not use IRQF_TRIGGER_FALLING
when requesting the IRQ. As this can result in missing interrupts.
Further, if the device tree specified the interrupt as "IRQ_TYPE_LEVEL_LOW",
unloading and reloading of the driver results in the following error during
ifup:
| irq: type mismatch, failed to map hwirq-31 for gpio@20a8000!
| tcan4x5x spi1.1: m_can device registered (irq=0, version=32)
| tcan4x5x spi1.1 can2: TCAN4X5X successfully initialized.
| tcan4x5x spi1.1 can2: failed to request interrupt
This patch fixes the problem by removing the IRQF_TRIGGER_FALLING from the
request_threaded_irq().
Fixes: f524f829b75a ("can: m_can: Create a m_can platform framework")
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Sriram Dash <sriram.dash@samsung.com>
Cc: Pankaj Sharma <pankj.sharma@samsung.com>
Link: https://lore.kernel.org/r/20201127093548.509253-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Enable new codec supported for ALC897.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/3b00520f304842aab8291eb8d9191bd8@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
When a packet is fragmented by batman-adv, the original batman-adv header
is not modified. Only a new fragmentation is inserted between the original
one and the ethernet header. The code must therefore make sure that it has
a writable region of this size in the skbuff head.
But it is not useful to always reallocate the skbuff by this size even when
there would be more than enough headroom still in the skb. The reallocation
is just to costly during in this codepath.
Fixes: ee75ed88879a ("batman-adv: Fragment and send skbs larger than mtu")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The batadv net_device is trying to propagate the needed_headroom and
needed_tailroom from the lower devices. This is needed to avoid cost
intensive reallocations using pskb_expand_head during the transmission.
But the fragmentation code split the skb's without adding extra room at the
end/beginning of the various fragments. This reduced the performance of
transmissions over complex scenarios (batadv on vxlan on wireguard) because
the lower devices had to perform the reallocations at least once.
Fixes: ee75ed88879a ("batman-adv: Fragment and send skbs larger than mtu")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
If a batman-adv packets has to be fragmented, then the original batman-adv
packet header is not stripped away. Instead, only a new header is added in
front of the packet after it was split.
This size must be considered to avoid cost intensive reallocations during
the transmission through the various device layers.
Fixes: 7bca68c7844b ("batman-adv: Add lower layer needed_(head|tail)room to own ones")
Reported-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
ssh://git.freedesktop.org/git/drm/drm-misc into drm-fixes
A bunch of fixes for vc4 fixing some coexistence issue between wifi and
HDMI, unsupported modes, and vblank timeouts, a fix for ast to reload
the gamma LUT after changing the plane format and a double-free fix for
nouveau
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20201126085450.r3i7wvj7pizsa4l6@gilmour
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/chunkuang.hu/linux into drm-fixes
Mediatek DRM Fixes for Linux 5.10
1. Remove unused variable.
2. Modify horizontal front/back porch byte formula.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20201123234131.387-1-chunkuang.hu@kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-fixes
One bug fix
. Add COMMON_CLK dependency to fix a build error below,
/usr/bin/mips-linux-gnu-ld: drivers/gpu/drm/exynos/exynos_mixer.o: in function `mixer_bind':
exynos_mixer.c:(.text+0x958): undefined reference to `clk_set_parent'
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Inki Dae <inki.dae@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1606184478-23384-1-git-send-email-inki.dae@samsung.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/fixes
arm64: tegra: Device tree fixes for v5.10-rc6
This contains a couple of fixes to device trees. Among other things,
this restores suspend/resume on Jetson TX2 and makes USB OTG work on
Jetson TX1.
* tag 'tegra-for-5.10-arm64-dt-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Fix Tegra234 VDK node names
arm64: tegra: Wrong AON HSP reg property size
arm64: tegra: Fix USB_VBUS_EN0 regulator on Jetson TX1
arm64: tegra: Correct the UART for Jetson Xavier NX
arm64: tegra: Disable the ACONNECT for Jetson TX2
Link: https://lore.kernel.org/r/20201125170306.1095734-1-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux into arm/fixes
NXP/FSL SoC driver fix for 5.10
DPAA2 DPIO driver
- Fix non-static cpumask for irq affinity setting
* tag 'soc-fsl-fix-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux:
soc: fsl: dpio: Get the cpumask through cpumask_of(cpu)
Link: https://lore.kernel.org/r/20201125165922.15487-1-leoyang.li@nxp.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://github.com/Xilinx/linux-xlnx into arm/fixes
arm64: soc: ZynqMP SoC fixes for v5.10-rc6
- Fix SD dll reset issue by using proper macro
- Fix PM feature checking for Xilinx Versal SoC
* tag 'zynqmp-soc-fixes-for-v5.10-rc6' of https://github.com/Xilinx/linux-xlnx: (337 commits)
firmware: xilinx: Use hash-table for api feature check
firmware: xilinx: Fix SD DLL node reset issue
Linux 5.10-rc4
kvm: mmu: fix is_tdp_mmu_check when the TDP MMU is not in use
afs: Fix afs_write_end() when called with copied == 0 [ver #3]
ocfs2: initialize ip_next_orphan
panic: don't dump stack twice on warn
hugetlbfs: fix anon huge page migration race
mm: memcontrol: fix missing wakeup polling thread
kernel/watchdog: fix watchdog_allowed_mask not used warning
reboot: fix overflow parsing reboot cpu number
Revert "kernel/reboot.c: convert simple_strtoul to kstrtoint"
compiler.h: fix barrier_data() on clang
mm/gup: use unpin_user_pages() in __gup_longterm_locked()
mm/slub: fix panic in slab_alloc_node()
mailmap: fix entry for Dmitry Baryshkov/Eremin-Solenikov
mm/vmscan: fix NR_ISOLATED_FILE corruption on 64-bit
mm/compaction: stop isolation if too many pages are isolated and we have pages to migrate
mm/compaction: count pages and stop correctly during page isolation
drm/nouveau/kms/nv50-: Use atomic encoder callbacks everywhere
...
Link: https://lore.kernel.org/r/fd5ab967-f3cf-95fb-7947-5477ff85f97e@monstr.eu
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fix from Rafael Wysocki:
"Fix a recently introduced build issue in the cpufreq SCMI driver
(Sudeep Holla)"
* tag 'pm-5.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: scmi: Fix build for !CONFIG_COMMON_CLK
|
|
Commit 20f829999c38 ("gfs2: Rework read and page fault locking") lifted
the glock lock taking from the low-level ->readpage and ->readahead
address space operations to the higher-level ->read_iter file and
->fault vm operations. The glocks are still taken in LM_ST_SHARED mode
only. On filesystems mounted without the noatime option, ->read_iter
sometimes needs to update the atime as well, though. Right now, this
leads to a failed locking mode assertion in gfs2_dirty_inode.
Fix that by introducing a new update_time inode operation. There, if
the glock is held non-exclusively, upgrade it to an exclusive lock.
Reported-by: Alexander Aring <aahringo@redhat.com>
Fixes: 20f829999c38 ("gfs2: Rework read and page fault locking")
Cc: stable@vger.kernel.org # v5.8+
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
|
|
Fix the missing clk_disable_unprepare() before return from
tegra_sor_init() in the error handling case.
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
0day reported one -22.7% regression for will-it-scale page_fault2
case [1] on a 4 sockets 144 CPU platform, and bisected to it to be
caused by Waiman's optimization (commit bd0b230fe1) of saving one
'struct page_counter' space for 'struct mem_cgroup'.
Initially we thought it was due to the cache alignment change introduced
by the patch, but further debug shows that it is due to some hot data
members ('vmstats_local', 'vmstats_percpu', 'vmstats') sit in 2 adjacent
cacheline (2N and 2N+1 cacheline), and when adjacent cache line prefetch
is enabled, it triggers an "extended level" of cache false sharing for
2 adjacent cache lines.
So exchange the 2 member blocks, while keeping mostly the original
cache alignment, which can restore and even enhance the performance,
and save 64 bytes of space for 'struct mem_cgroup' (from 2880 to 2816,
with 0day's default RHEL-8.3 kernel config)
[1]. https://lore.kernel.org/lkml/20201102091543.GM31092@shao2-debian/
Fixes: bd0b230fe145 ("mm/memcg: unify swap and memsw page counters")
Reported-by: kernel test robot <rong.a.chen@intel.com>
Signed-off-by: Feng Tang <feng.tang@intel.com>
Acked-by: Waiman Long <longman@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This wasn't initialized for pre NV50 hardware.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reported-and-Tested-by: Mark Hounschell <markh@compro.net>
Reviewed-by: Karol Herbst <kherbst@redhat.com>
Link: https://patchwork.freedesktop.org/series/84298/
|
|
When one task is in io_uring_cancel_files() and another is doing
io_prep_async_work() a race may happen. That's because after accounting
a request inflight in first call to io_grab_identity() it still may fail
and go to io_identity_cow(), which migh briefly keep dangling
work.identity and not only.
Grab files last, so io_prep_async_work() won't fail if it did get into
->inflight_list.
note: the bug shouldn't exist after making io_uring_cancel_files() not
poking into other tasks' requests.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
When a memory window is bound to a memory region, the local write access
should be set for its mtpt table.
Fixes: c7c28191408b ("RDMA/hns: Add MW support for hip08")
Link: https://lore.kernel.org/r/1606386372-21094-1-git-send-email-liweihang@huawei.com
Signed-off-by: Yixian Liu <liuyixian@huawei.com>
Signed-off-by: Weihang Li <liweihang@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
The maximum number of retransmission should be returned when querying QP,
not the value of retransmission counter.
Fixes: 99fcf82521d9 ("RDMA/hns: Fix the wrong value of rnr_retry when querying qp")
Fixes: 926a01dc000d ("RDMA/hns: Add QP operations support for hip08 SoC")
Link: https://lore.kernel.org/r/1606382977-21431-1-git-send-email-liweihang@huawei.com
Signed-off-by: Wenpeng Liang <liangwenpeng@huawei.com>
Signed-off-by: Weihang Li <liweihang@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
The SRQ capacity is got from the firmware, whose field should be ended at
bit 19.
Fixes: ba6bb7e97421 ("RDMA/hns: Add interfaces to get pf capabilities from firmware")
Link: https://lore.kernel.org/r/1606382812-23636-1-git-send-email-liweihang@huawei.com
Signed-off-by: Wenpeng Liang <liangwenpeng@huawei.com>
Signed-off-by: Weihang Li <liweihang@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
My virtual IOMMU implementation is whining that the guest is reading a
register that doesn't exist. Only read the VCCAP_REG if the corresponding
capability is set in ECAP_REG to indicate that it actually exists.
Fixes: 3375303e8287 ("iommu/vt-d: Add custom allocator for IOASID")
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Liu Yi L <yi.l.liu@intel.com>
Cc: stable@vger.kernel.org # v5.7+
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/de32b150ffaa752e0cff8571b17dfb1213fbe71c.camel@infradead.org
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Add touchscreen info for the Irbis TW118 tablet.
Reported-and-tested-by: russianneuromancer <russianneuromancer@ya.ru>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20201124110454.114286-1-hdegoede@redhat.com
|
|
Add touchscreen info for the Predia Basic tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20201015194949.50566-1-hdegoede@redhat.com
|
|
The Pavilion 13 x360 PC has a chassis-type which does not indicate it is
a convertible, while it is actually a convertible. Add it to the
dmi_switches_allow_list.
Signed-off-by: Max Verevkin <me@maxverevkin.tk>
Link: https://lore.kernel.org/r/20201124131652.11165-1-me@maxverevkin.tk
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The commit 78429e55e4057 ("platform/x86: toshiba_acpi: Clean up
variable declaration") cleans up variable declaration in
video_proc_write(). Seems it does the variable assignment in the
wrong place, this results in dead code and changes the source code
logic. Fix it by doing the assignment at the beginning of the funciton.
Fixes: 78429e55e4057 ("platform/x86: toshiba_acpi: Clean up variable declaration")
Reported-by: Tosk Robot <tencent_os_robot@tencent.com>
Signed-off-by: Kaixu Xia <kaixuxia@tencent.com>
Link: https://lore.kernel.org/r/1606024177-16481-1-git-send-email-kaixuxia@tencent.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
as KEY_LIGHTS_TOGGLE
Got a dmesg message on my AMD Renoir based Acer laptop:
"acer_wmi: Unknown key number - 0x84" when toggling keyboard
background light
Signed-off-by: Timo Witte <timo.witte@gmail.com>
Reviewed-by: "Lee, Chun-Yi" <jlee@suse.com>
Link: https://lore.kernel.org/r/20200804001423.36778-1-timo.witte@gmail.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
This commit enables dual fan control for the following new Lenovo
models: P15, P15v.
Signed-off-by: Matthias Maier <tamiko@43-1.org>
Link: https://lore.kernel.org/r/20201126000416.2459645-2-tamiko-ibm-acpi-devel@43-1.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The lid state may change while the machine is suspended. As such, we may
need to re-check the state at wake-up time (at least when waking up from
hibernation).
Add the appropriate call to the resume handler in order to sync the
SW_TABLET_MODE switch state with the hardware state.
Fixes: dda3ec0aa631 ("platform/x86: thinkpad_acpi: Implement tablet mode using GMMS method")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=210269
Signed-off-by: Benjamin Berg <bberg@redhat.com>
Acked-by: Henrique de Moraes Holschuh <hnh@hmh.eng.br>
Link: https://lore.kernel.org/r/20201123132157.866303-1-benjamin@sipsolutions.net
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Yoga 11e 4th gen
The Thinkpad Yoga 11e 4th gen with the N3450 / Celeron CPU only has
one battery which is named BAT1 instead of the expected BAT0, add a
quirk for this. This fixes not being able to set the charging tresholds
on this model; and this alsoe fixes the following errors in dmesg:
ACPI: \_SB_.PCI0.LPCB.EC__.HKEY: BCTG evaluated but flagged as error
thinkpad_acpi: Error probing battery 2
battery: extension failed to load: ThinkPad Battery Extension
battery: extension unregistered: ThinkPad Battery Extension
Note that the added quirk is for the "R0K" BIOS versions which are
used on the Thinkpad Yoga 11e 4th gen's with a Celeron CPU, there
is a separate "R0L" BIOS for the i3/i5 based versions. This may also
need the same quirk, but if that really is necessary is unknown.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20201109103550.16265-1-hdegoede@redhat.com
|
|
The Yoga 11e series has 2 accelerometers described by a BOSC0200 ACPI node.
This setup relies on a Windows service which reads both accelerometers and
then calculates the angle between the 2 halves to determine laptop / tent /
tablet mode and then reports the calculated mode back to the EC by calling
special ACPI methods on the BOSC0200 node.
The bmc150 iio driver does not support this (it involves double
calculations requiring sqrt and arccos so this really needs to be done
in userspace), as a result of this on the Yoga 11e the thinkpad_acpi
code always reports SW_TABLET_MODE=0, starting with GNOME 3.38 reporting
SW_TABLET_MODE=0 causes GNOME to:
1. Not show the onscreen keyboard when a text-input field is focussed
with the touchscreen.
2. Disable accelerometer based auto display-rotation.
This makes sense when in laptop-mode but not when in tablet-mode. But
since for the Yoga 11e the thinkpad_acpi code always reports
SW_TABLET_MODE=0, GNOME does not know when the device is in tablet-mode.
Stop reporting the broken (always 0) SW_TABLET_MODE on Yoga 11e models
to fix this.
Note there are plans for userspace to support 360 degree hinges style
2-in-1s with 2 accelerometers and figure out the mode by itself, see:
https://gitlab.freedesktop.org/hadess/iio-sensor-proxy/-/issues/216
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20201106140130.46820-1-hdegoede@redhat.com
|
|
Tested on my P1 gen3, works fine with `thinkfan`. Since thinkpad_acpi fan
control is off by default, it is safe to add 2nd fan control for brave
overclockers
Signed-off-by: Iakov 'Jake' Kirilenko <jake.kirilenko@gmail.com>
Link: https://lore.kernel.org/r/20201105152556.34073-1-jake.kirilenko@gmail.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
When offlining a CPU, powerpc/64s does not flush TLBs, rather it just
leaves the CPU set in mm_cpumasks, so it continues to receive TLBIEs
to manage its TLBs.
However the exit_flush_lazy_tlbs() function expects that after
returning, all CPUs (except self) have flushed TLBs for that mm, in
which case TLBIEL can be used for this flush. This breaks for offline
CPUs because they don't get the IPI to flush their TLB. This can lead
to stale translations.
Fix this by clearing the CPU from mm_cpumasks, then flushing all TLBs
before going offline.
These offlined CPU bits stuck in the cpumask also prevents the cpumask
from being trimmed back to local mode, which means continual broadcast
IPIs or TLBIEs are needed for TLB flushing. This patch prevents that
situation too.
A cast of many were involved in working this out, but in particular
Milton, Aneesh, Paul made key discoveries.
Fixes: 0cef77c7798a7 ("powerpc/64s/radix: flush remote CPUs out of single-threaded mm_cpumask")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Debugged-by: Milton Miller <miltonm@us.ibm.com>
Debugged-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Debugged-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201126102530.691335-5-npiggin@gmail.com
|
|
powerpc/64s keeps a counter in the mm which counts bits set in
mm_cpumask as well as other things. This means it can't use generic code
to clear bits out of the mask and doesn't adjust the arch specific
counter.
Add an arch override that allows powerpc/64s to use
clear_tasks_mm_cpumask().
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201126102530.691335-4-npiggin@gmail.com
|
|
tlbiel_all() can not be usable in !HVMODE when running hash presently,
remove HV privileged flushes when running in guest to make it usable.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201126102530.691335-3-npiggin@gmail.com
|
|
A typo has the R field of the instruction assigned by lucky dip a la
register allocator.
Fixes: d4748276ae14c ("powerpc/64s: Improve local TLB flush for boot and MCE on POWER9")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201126102530.691335-2-npiggin@gmail.com
|
|
To fix errors in some 4 poles headset detection cases,
this patch adjusts the voltage threshold for mic detection.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20201126092759.9427-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This will make sure applications which use the IN_FORMATS blob
to figure out which modifiers they can use will pick up the
linear modifier which is needed by mxsfb. Such applications
will not work otherwise if an incompatible implicit modifier
ends up being selected.
Before commit ae1ed0093281 ("drm: mxsfb: Stop using DRM simple
display pipeline helper"), the DRM simple display pipeline
helper took care of this.
Signed-off-by: Daniel Abrecht <public@danielabrecht.ch>
Fixes: ae1ed0093281 ("drm: mxsfb: Stop using DRM simple display pipeline helper")
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/2a99ffffc2378209307e0992a6e97e70@nodmarc.danielabrecht.ch
|
|
The conversion away from the simple display pipeline helper missed
to convert the prepare_fb plane callback, so no fences are attached to
the atomic state, breaking synchronization with other devices. Fix
this by plugging in the drm_gem_fb_prepare_fb helper function.
Fixes: ae1ed0093281 ("drm: mxsfb: Stop using DRM simple display pipeline helper")
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20201120211306.325841-1-l.stach@pengutronix.de
|
|
This patch add a check to the mcp251xfd_probe() function to bail out and give
the user a proper error message if no IRQ is specified. Otherwise the driver
will probe just fine but ifup will fail with a meaningless "RTNETLINK answers:
Invalid argument" error message.
Link: https://lore.kernel.org/r/20201123113522.3820052-1-mkl@pengutronix.de
Reported-by: Niels Petter <petter@ka-long.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The firmware on the original USB2CAN by Geschwister Schneider Technologie
Entwicklungs- und Vertriebs UG exchanges all data between the host and the
device in host byte order. This is done with the struct
gs_host_config::byte_order member, which is sent first to indicate the desired
byte order.
The widely used open source firmware candleLight doesn't support this feature
and exchanges the data in little endian byte order. This breaks if a device
with candleLight firmware is used on big endianess systems.
To fix this problem, all u32 (but not the struct gs_host_frame::echo_id, which
is a transparent cookie) are converted to __le32.
Cc: Maximilian Schneider <max@schneidersoft.net>
Cc: Hubert Denkmair <hubert@denkmair.de>
Reported-by: Michael Rausch <mr@netadair.de>
Link: https://lore.kernel.org/r/b58aace7-61f3-6df7-c6df-69fee2c66906@netadair.de
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Fixes: d08e973a77d1 ("can: gs_usb: Added support for the GS_USB CAN devices")
Link: https://lore.kernel.org/r/20201120103818.3386964-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
With the steady stream of new features coming into the subsystem
it has been clear for some time now that help is needed.
Suzuki and Leo have worked extensively on various parts of the
project and have agreed to help.
While at it add the new location for the coresight git tree.
Acked-by: Leo Yan <leo.yan@linaro.org>
Acked-by : Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20201125223519.734388-1-mathieu.poirier@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
- Fix Perf/OA workaround register corruption (Lionel)
- Correct a comment statement in GVT (Yan)
- Fix GT enable/disable iterrupts, including a race condition that prevented GPU to go idle (Chris)
- Free stale request on destroying the virtual engine (Chris)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201126010623.GA827684@intel.com
|
|
git://people.freedesktop.org/~agd5f/linux into drm-fixes
amd-drm-fixes-5.10-2020-11-25:
amdgpu:
- Runtime pm fix
- SI UVD suspend/resume fix
- HDCP fix for headless cards
- Sienna Cichlid golden register update
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201125151145.4263-1-alexander.deucher@amd.com
|
|
Fix existing issues at the kernel-doc markups and add them to
the vidtv.rst file.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Update the vidtv documentation with the relevant changes
after the last patches.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
- pass struct vidtv_psi_eit_write_args as a pointer;
- avoid initializing struct fields multiple times.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
- pass struct vidtv_psi_nit_write_args as a pointer;
- avoid initializing struct fields multiple times.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
