| Age | Commit message (Collapse) | Author |
|---|
|
Slave function read the following capabilities from the wrong offset:
1. log_mc_entry_sz
2. fs_log_entry_sz
3. log_mc_hash_sz
Fix that by adjusting these capabilities offset to match firmware
layout.
Due to the wrong offset read, the following issues might occur:
1+2. Negative value reported at max_mcast_qp_attach.
3. Driver to init FW with multicast hash size of zero.
Fixes: a40ded604365 ("net/mlx4_core: Add masking for a few queries on HCA caps")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Eran Ben Elisha <eranbe@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20201118081922.553-1-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes 2020-11-17
This series introduces some fixes to mlx5 driver.
* tag 'mlx5-fixes-2020-11-17' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5: fix error return code in mlx5e_tc_nic_init()
net/mlx5: E-Switch, Fail mlx5_esw_modify_vport_rate if qos disabled
net/mlx5: Disable QoS when min_rates on all VFs are zero
net/mlx5: Clear bw_share upon VF disable
net/mlx5: Add handling of port type in rule deletion
net/mlx5e: Fix check if netdev is bond slave
net/mlx5e: Fix IPsec packet drop by mlx5e_tc_update_skb
net/mlx5e: Set IPsec WAs only in IP's non checksum partial case.
net/mlx5e: Fix refcount leak on kTLS RX resync
====================
Link: https://lore.kernel.org/r/20201117195702.386113-1-saeedm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The `skb' is mapped for DMA in ns_send() but does not unmap DMA in case
push_scqe() fails to submit the `skb'. The memory of the `skb' is
released so only the DMA mapping is leaking.
Unmap the DMA mapping in case push_scqe() failed.
Fixes: 864a3ff635fa7 ("atm: [nicstar] remove virt_to_bus() and support 64-bit platforms")
Cc: Chas Williams <3chas3@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The ethernet driver may allocate skb (and skb->data) via napi_alloc_skb().
This ends up to page_frag_alloc() to allocate skb->data from
page_frag_cache->va.
During the memory pressure, page_frag_cache->va may be allocated as
pfmemalloc page. As a result, the skb->pfmemalloc is always true as
skb->data is from page_frag_cache->va. The skb will be dropped if the
sock (receiver) does not have SOCK_MEMALLOC. This is expected behaviour
under memory pressure.
However, once kernel is not under memory pressure any longer (suppose large
amount of memory pages are just reclaimed), the page_frag_alloc() may still
re-use the prior pfmemalloc page_frag_cache->va to allocate skb->data. As a
result, the skb->pfmemalloc is always true unless page_frag_cache->va is
re-allocated, even if the kernel is not under memory pressure any longer.
Here is how kernel runs into issue.
1. The kernel is under memory pressure and allocation of
PAGE_FRAG_CACHE_MAX_ORDER in __page_frag_cache_refill() will fail. Instead,
the pfmemalloc page is allocated for page_frag_cache->va.
2: All skb->data from page_frag_cache->va (pfmemalloc) will have
skb->pfmemalloc=true. The skb will always be dropped by sock without
SOCK_MEMALLOC. This is an expected behaviour.
3. Suppose a large amount of pages are reclaimed and kernel is not under
memory pressure any longer. We expect skb->pfmemalloc drop will not happen.
4. Unfortunately, page_frag_alloc() does not proactively re-allocate
page_frag_alloc->va and will always re-use the prior pfmemalloc page. The
skb->pfmemalloc is always true even kernel is not under memory pressure any
longer.
Fix this by freeing and re-allocating the page instead of recycling it.
References: https://lore.kernel.org/lkml/20201103193239.1807-1-dongli.zhang@oracle.com/
References: https://lore.kernel.org/linux-mm/20201105042140.5253-1-willy@infradead.org/
Suggested-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Aruna Ramakrishna <aruna.ramakrishna@oracle.com>
Cc: Bert Barbe <bert.barbe@oracle.com>
Cc: Rama Nichanamatlu <rama.nichanamatlu@oracle.com>
Cc: Venkat Venkatsubra <venkat.x.venkatsubra@oracle.com>
Cc: Manjunath Patil <manjunath.b.patil@oracle.com>
Cc: Joe Jin <joe.jin@oracle.com>
Cc: SRINIVAS <srinivas.eeda@oracle.com>
Fixes: 79930f5892e1 ("net: do not deplete pfmemalloc reserve")
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20201115201029.11903-1-dongli.zhang@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We recently improved our display atomic commit and tail sequence to
avoid some issues related to concurrency. One of the major changes
consisted of moving the interrupt disable and the stream release from
our atomic commit to our atomic tail (commit 6d90a208cfff
("drm/amd/display: Move disable interrupt into commit tail")) .
However, the new code introduced inside our commit tail function was
inserted right after the function
drm_atomic_helper_update_legacy_modeset_state(), which has routines for
updating internal data structs related to timestamps. As a result, in
certain conditions, the display module can reach a situation where we
update our constants and, after that, clean it. This situation generates
the following warning:
amdgpu 0000:03:00.0: drm_WARN_ON_ONCE(drm_drv_uses_atomic_modeset(dev))
WARNING: CPU: 6 PID: 1269 at drivers/gpu/drm/drm_vblank.c:722
drm_crtc_vblank_helper_get_vblank_timestamp_internal+0x32b/0x340 [drm]
...
RIP:
0010:drm_crtc_vblank_helper_get_vblank_timestamp_internal+0x32b/0x340
[drm]
...
Call Trace:
? dc_stream_get_vblank_counter+0x57/0x60 [amdgpu]
drm_crtc_vblank_helper_get_vblank_timestamp+0x1c/0x20 [drm]
drm_get_last_vbltimestamp+0xad/0xc0 [drm]
drm_reset_vblank_timestamp+0x63/0xd0 [drm]
drm_crtc_vblank_on+0x85/0x150 [drm]
amdgpu_dm_atomic_commit_tail+0xaf1/0x2330 [amdgpu]
commit_tail+0x99/0x130 [drm_kms_helper]
drm_atomic_helper_commit+0x123/0x150 [drm_kms_helper]
amdgpu_dm_atomic_commit+0x11/0x20 [amdgpu]
drm_atomic_commit+0x4a/0x50 [drm]
drm_atomic_helper_set_config+0x7c/0xc0 [drm_kms_helper]
drm_mode_setcrtc+0x20b/0x7e0 [drm]
? tomoyo_path_number_perm+0x6f/0x200
? drm_mode_getcrtc+0x190/0x190 [drm]
drm_ioctl_kernel+0xae/0xf0 [drm]
drm_ioctl+0x245/0x400 [drm]
? drm_mode_getcrtc+0x190/0x190 [drm]
amdgpu_drm_ioctl+0x4e/0x80 [amdgpu]
__x64_sys_ioctl+0x91/0xc0
do_syscall_64+0x38/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xa9
...
For fixing this issue we rely upon a refactor introduced on
drm_atomic_helper_update_legacy_modeset_state ("Remove the timestamping
constant update from drm_atomic_helper_update_legacy_modeset_state()")
which decouples constant values update from
drm_atomic_helper_update_legacy_modeset_state to a new helper.
Basically, this commit uses this new helper and place it right after our
release module to avoid a situation where our CRTC struct gets wrong
values.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1373
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1349
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2
Pull gfs2 fix from Andreas Gruenbacher:
"Fix gfs2 freeze/thaw"
* tag 'gfs2-v5.10-rc4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2:
gfs2: Fix regression in freeze_go_sync
|
|
Pull nfsd fix from Bruce Fields:
"Just one quick fix for a tracing oops"
* tag 'nfsd-5.10-2' of git://linux-nfs.org/~bfields/linux:
SUNRPC: Fix oops in the rpc_xdr_buf event class
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull Kunit fixes from Shuah Khan:
"Several fixes to Kunit documentation and tools, and to not pollute
the source directory.
Also remove the incorrect kunit .gitattributes file"
* tag 'linux-kselftest-kunit-fixes-5.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
kunit: fix display of failed expectations for strings
kunit: tool: fix extra trailing \n in raw + parsed test output
kunit: tool: print out stderr from make (like build warnings)
KUnit: Docs: usage: wording fixes
KUnit: Docs: style: fix some Kconfig example issues
KUnit: Docs: fix a wording typo
kunit: Do not pollute source directory with generated files (test.log)
kunit: Do not pollute source directory with generated files (.kunitconfig)
kunit: tool: fix pre-existing python type annotation errors
kunit: Fix kunit.py parse subcommand (use null build_dir)
kunit: tool: unmark test_data as binary blobs
|
|
When the switch is hardware reset, it reads the contents of the
EEPROM. This can contain instructions for programming values into
registers and to perform waits between such programming. Reading the
EEPROM can take longer than the 100ms mv88e6xxx_hardware_reset() waits
after deasserting the reset GPIO. So poll the EEPROM done bit to
ensure it is complete.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ruslan Sushko <rus@sushko.dev>
Link: https://lore.kernel.org/r/20201116164301.977661-1-rus@sushko.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Ido Schimmel says:
====================
mlxsw: Couple of fixes
Patch #1 fixes firmware flashing when CONFIG_MLXSW_CORE=y and
CONFIG_MLXFW=m.
Patch #2 prevents EMAD transactions from needlessly failing when the
system is under heavy load by using exponential backoff.
Please consider patch #2 for stable.
====================
Link: https://lore.kernel.org/r/20201117173352.288491-1-idosch@idosch.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The driver sends Ethernet Management Datagram (EMAD) packets to the
device for configuration purposes and waits for up to 200ms for a reply.
A request is retried up to 5 times.
When the system is under heavy load, replies are not always processed in
time and EMAD transactions fail.
Make the process more robust to such delays by using exponential
backoff. First wait for up to 200ms, then retransmit and wait for up to
400ms and so on.
Fixes: caf7297e7ab5 ("mlxsw: core: Introduce support for asynchronous EMAD register access")
Reported-by: Denis Yulevich <denisyu@nvidia.com>
Tested-by: Denis Yulevich <denisyu@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The commit cited below moved firmware flashing functionality from
mlxsw_spectrum to mlxsw_core, but did not adjust the Kconfig
dependencies. This makes it possible to have mlxsw_core as built-in and
mlxfw as a module. The mlxfw code is therefore not reachable from
mlxsw_core and firmware flashing fails:
# devlink dev flash pci/0000:01:00.0 file mellanox/mlxsw_spectrum-13.2008.1310.mfa2
devlink answers: Operation not supported
Fix by having mlxsw_core select mlxfw.
Fixes: b79cb787ac70 ("mlxsw: Move fw flashing code into core.c")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reported-by: Vadim Pasternak <vadimp@nvidia.com>
Tested-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
DSA network devices rely on having their DSA management interface up and
running otherwise their ndo_open() will return -ENETDOWN. Without doing
this it would not be possible to use DSA devices as netconsole when
configured on the command line. These devices also do not utilize the
upper/lower linking so the check about the netpoll device having upper
is not going to be a problem.
The solution adopted here is identical to the one done for
net/ipv4/ipconfig.c with 728c02089a0e ("net: ipv4: handle DSA enabled
master network devices"), with the network namespace scope being
restricted to that of the process configuring netpoll.
Fixes: 04ff53f96a93 ("net: dsa: Add netconsole support")
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20201117035236.22658-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: a6a5325239c2 ("atl1e: Atheros L1E Gigabit Ethernet driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/r/1605581875-36281-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 43250ddd75a3 ("atl1c: Atheros L1C Gigabit Ethernet driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/r/1605581721-36028-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/r/1605581105-35295-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
LTE module MR400 embedded in TL-MR6400 v4 requires DTR to be set.
Signed-off-by: Filip Moc <dev@moc6.cz>
Acked-by: Bjørn Mork <bjorn@mork.no>
Link: https://lore.kernel.org/r/20201117173631.GA550981@moc6.cz
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
At the start of driver initialization, we do not know what bias
setting the bootloader has configured the system for and we only know
for certain the very first time we do a transition.
However, since the initial value of the comparison index is -EINVAL,
this negative value results in an array out of bound access on the
very first transition.
Since we don't know what the setting is, we just set the bias
configuration as there is nothing to compare against. This prevents
the array out of bound access.
NOTE: Even though we could use a more relaxed check of "< 0" the only
valid values(ignoring cosmic ray induced bitflips) are -EINVAL, 0+.
Fixes: 40b1936efebd ("regulator: Introduce TI Adaptive Body Bias(ABB) on-chip LDO driver")
Link: https://lore.kernel.org/linux-mm/CA+G9fYuk4imvhyCN7D7T6PMDH6oNp6HDCRiTUKMQ6QXXjBa4ag@mail.gmail.com/
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20201118145009.10492-1-nm@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In kabylake_set_bias_level(), enabling mclk may fail if the clock has
already been enabled by the firmware. Attempts to disable that clock
later will fail with a warning backtrace.
mclk already disabled
WARNING: CPU: 2 PID: 108 at drivers/clk/clk.c:952 clk_core_disable+0x1b6/0x1cf
...
Call Trace:
clk_disable+0x2d/0x3a
kabylake_set_bias_level+0x72/0xfd [snd_soc_kbl_rt5663_rt5514_max98927]
snd_soc_card_set_bias_level+0x2b/0x6f
snd_soc_dapm_set_bias_level+0xe1/0x209
dapm_pre_sequence_async+0x63/0x96
async_run_entry_fn+0x3d/0xd1
process_one_work+0x2a9/0x526
...
Only disable the clock if it has been enabled.
Fixes: 15747a802075 ("ASoC: eve: implement set_bias_level function for rt5514")
Cc: Brent Lu <brent.lu@intel.com>
Cc: Curtis Malainey <cujomalainey@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20201111205434.207610-1-linux@roeck-us.net
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In xfs_initialize_perag(), if kmem_zalloc(), xfs_buf_hash_init(), or
radix_tree_preload() failed, the returned value 'error' is not set
accordingly.
Reported-as-fixing: 8b26c5825e02 ("xfs: handle ENOMEM correctly during initialisation of perag structures")
Fixes: 9b2471797942 ("xfs: cache unlinked pointers in an rhashtable")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
|
|
The aim of the inode btree record iterator function is to call a
callback on every record in the btree. To avoid having to tear down and
recreate the inode btree cursor around every callback, it caches a
certain number of records in a memory buffer. After each batch of
callback invocations, we have to perform a btree lookup to find the
next record after where we left off.
However, if the keys of the inode btree are corrupt, the lookup might
put us in the wrong part of the inode btree, causing the walk function
to loop forever. Therefore, we add extra cursor tracking to make sure
that we never go backwards neither when performing the lookup nor when
jumping to the next inobt record. This also fixes an off by one error
where upon resume the lookup should have been for the inode /after/ the
point at which we stopped.
Found by fuzzing xfs/460 with keys[2].startino = ones causing bulkstat
and quotacheck to hang.
Fixes: a211432c27ff ("xfs: create simplified inode walk function")
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Chandan Babu R <chandanrlinux@gmail.com>
|
|
Currently, commit e9e2eae89ddb dropped a (int) decoration from
XFS_LITINO(mp), and since sizeof() expression is also involved,
the result of XFS_LITINO(mp) is simply as the size_t type
(commonly unsigned long).
Considering the expression in xfs_attr_shortform_bytesfit():
offset = (XFS_LITINO(mp) - bytes) >> 3;
let "bytes" be (int)340, and
"XFS_LITINO(mp)" be (unsigned long)336.
on 64-bit platform, the expression is
offset = ((unsigned long)336 - (int)340) >> 3 =
(int)(0xfffffffffffffffcUL >> 3) = -1
but on 32-bit platform, the expression is
offset = ((unsigned long)336 - (int)340) >> 3 =
(int)(0xfffffffcUL >> 3) = 0x1fffffff
instead.
so offset becomes a large positive number on 32-bit platform, and
cause xfs_attr_shortform_bytesfit() returns maxforkoff rather than 0.
Therefore, one result is
"ASSERT(new_size <= XFS_IFORK_SIZE(ip, whichfork));"
assertion failure in xfs_idata_realloc(), which was also the root
cause of the original bugreport from Dennis, see:
https://bugzilla.redhat.com/show_bug.cgi?id=1894177
And it can also be manually triggered with the following commands:
$ touch a;
$ setfattr -n user.0 -v "`seq 0 80`" a;
$ setfattr -n user.1 -v "`seq 0 80`" a
on 32-bit platform.
Fix the case in xfs_attr_shortform_bytesfit() by bailing out
"XFS_LITINO(mp) < bytes" in advance suggested by Eric and a misleading
comment together with this bugfix suggested by Darrick. It seems the
other users of XFS_LITINO(mp) are not impacted.
Fixes: e9e2eae89ddb ("xfs: only check the superblock version for dinode size calculation")
Cc: <stable@vger.kernel.org> # 5.7+
Reported-and-tested-by: Dennis Gilmore <dgilmore@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Gao Xiang <hsiangkao@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
|
|
Teach the directory scrubber to check all the bestfree entries,
including the null ones. We want to be able to detect the case where
the entry is null but there actually /is/ a directory data block.
Found by fuzzing lbests[0] = ones in xfs/391.
Fixes: df481968f33b ("xfs: scrub directory freespace")
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Chandan Babu R <chandanrlinux@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
|
|
We always know the correct state of the rmap record flags (attr, bmbt,
unwritten) so check them by direct comparison.
Fixes: d852657ccfc0 ("xfs: cross-reference reverse-mapping btree")
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Chandan Babu R <chandanrlinux@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
|
|
The comment and logic in xchk_btree_check_minrecs for dealing with
inode-rooted btrees isn't quite correct. While the direct children of
the inode root are allowed to have fewer records than what would
normally be allowed for a regular ondisk btree block, this is only true
if there is only one child block and the number of records don't fit in
the inode root.
Fixes: 08a3a692ef58 ("xfs: btree scrub should check minrecs")
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Chandan Babu R <chandanrlinux@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into kvm-master
KVM: s390: Fix for destroy page ultravisor call
- handle response code from older firmware
- add uv.c to KVM: s390/s390 maintainer list
|
|
Avoid processing bogus interrupt statuses when the HW is runtime suspended and
the M_CAN_IR register read may get all bits 1's. Handler can be called if the
interrupt request is shared with other peripherals or at the end of free_irq().
Therefore check the runtime suspended status before processing.
Fixes: cdf8259d6573 ("can: m_can: Add PM Support")
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20200915134715.696303-1-jarkko.nikula@linux.intel.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Patch 541656d3a513 ("gfs2: freeze should work on read-only mounts") changed
the check for glock state in function freeze_go_sync() from "gl->gl_state
== LM_ST_SHARED" to "gl->gl_req == LM_ST_EXCLUSIVE". That's wrong and it
regressed gfs2's freeze/thaw mechanism because it caused only the freezing
node (which requests the glock in EX) to queue freeze work.
All nodes go through this go_sync code path during the freeze to drop their
SHared hold on the freeze glock, allowing the freezing node to acquire it
in EXclusive mode. But all the nodes must freeze access to the file system
locally, so they ALL must queue freeze work. The freeze_work calls
freeze_func, which makes a request to reacquire the freeze glock in SH,
effectively blocking until the thaw from the EX holder. Once thawed, the
freezing node drops its EX hold on the freeze glock, then the (blocked)
freeze_func reacquires the freeze glock in SH again (on all nodes, including
the freezer) so all nodes go back to a thawed state.
This patch changes the check back to gl_state == LM_ST_SHARED like it was
prior to 541656d3a513.
Fixes: 541656d3a513 ("gfs2: freeze should work on read-only mounts")
Cc: stable@vger.kernel.org # v5.8+
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
|
|
flexcan_transceiver_enable() during bus-off recovery
If the CAN controller goes into bus off, the do_set_mode() callback with
CAN_MODE_START can be used to recover the controller, which then calls
flexcan_chip_start(). If configured, this is done automatically by the
framework or manually by the user.
In flexcan_chip_start() there is an explicit call to
flexcan_transceiver_enable(), which does a regulator_enable() on the
transceiver regulator. This results in a net usage counter increase, as there
is no corresponding flexcan_transceiver_disable() in the bus off code path.
This further leads to the transceiver stuck enabled, even if the CAN interface
is shut down.
To fix this problem the
flexcan_transceiver_enable()/flexcan_transceiver_disable() are moved out of
flexcan_chip_start()/flexcan_chip_stop() into flexcan_open()/flexcan_close().
Fixes: e955cead0311 ("CAN: Add Flexcan CAN controller driver")
Link: https://lore.kernel.org/r/20201118150148.2664024-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Don't recycle a refnode until we're done with all requests of nodes
ejected before.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Cc: stable@vger.kernel.org # v5.7+
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
An active ref_node always can be found in ctx->files_data, it's much
safer to get it this way instead of poking into files_data->ref_list.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Cc: stable@vger.kernel.org # v5.7+
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
"intel_iommu=off" command line is used to disable iommu but iommu is force
enabled in a tboot system for security reason.
However for better performance on high speed network device, a new option
"intel_iommu=tboot_noforce" is introduced to disable the force on.
By default kernel should panic if iommu init fail in tboot for security
reason, but it's unnecessory if we use "intel_iommu=tboot_noforce,off".
Fix the code setting force_on and move intel_iommu_tboot_noforce
from tboot code to intel iommu code.
Fixes: 7304e8f28bb2 ("iommu/vt-d: Correctly disable Intel IOMMU force on")
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@gmail.com>
Tested-by: Lukasz Hawrylko <lukasz.hawrylko@linux.intel.com>
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20201110071908.3133-1-zhenzhong.duan@gmail.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
The error codes were not set on some of these error paths.
Also the error handling was more confusing than it needed to be so I
cleaned it up and shuffled it around a bit.
Fixes: d2fb0a043838 ("dmaengine: break out channel registration")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20201113101631.GE168908@mwanda
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Most changes in uv.c are related to KVM. Involve also the KVM team
regarding changes to uv.c.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Older firmware can return rc=0x107 rrc=0xd for destroy page if the
page is already non-secure. This should be handled like a success
as already done by newer firmware.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Fixes: 1a80b54d1ce1 ("s390/uv: add destroy page call")
Reviewed-by: David Hildenbrand <david@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
|
|
sysrq-t ends up invoking show_opcodes() for each task which tries to access
the user space code of other processes, which is obviously bogus.
It either manages to dump where the foreign task's regs->ip points to in a
valid mapping of the current task or triggers a pagefault and prints "Code:
Bad RIP value.". Both is just wrong.
Add a safeguard in copy_code() and check whether the @regs pointer matches
currents pt_regs. If not, do not even try to access it.
While at it, add commentary why using copy_from_user_nmi() is safe in
copy_code() even if the function name suggests otherwise.
Reported-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Borislav Petkov <bp@suse.de>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Tested-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20201117202753.667274723@linutronix.de
|
|
While powering down, the device may or may not acknowledge an MHI
RESET issued by host for a graceful shutdown scenario and end up
sending an incoming data packet after tasklets have been killed.
If a rogue device sends this interrupt for a data transfer event
ring update, it can result in a tasklet getting scheduled while a
clean up is ongoing or has completed and cause access to freed
memory leading to a NULL pointer exception. Remove the interrupt
handlers for MHI event rings early on to avoid this scenario.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
mhi_power_down() does not ensure that the PM state is moved to an
inaccessible state soon enough as the system can encounter
scheduling delays till mhi_pm_disable_transition() gets called.
Additionally, if an MHI controller decides that the device is now
inaccessible and issues a power down, the register inaccessible
state is not maintained by moving from MHI_PM_LD_ERR_FATAL_DETECT
to MHI_PM_SHUTDOWN_PROCESS. This can result in bus errors if a
client driver attempted to read registers when powering down.
Close these gaps and avoid any race conditions to prevent such
activity.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Currently, there exist a set of if...else statements in the
mhi_pm_disable_transition() function which make handling system
error and disable transitions differently complex. To make that
cleaner and facilitate differences in behavior, separate these
two transitions for MHI host.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Current design allows a controller to register with MHI successfully
without the need to have any IRQs available for use. If no IRQs are
available, power up requests to MHI can fail after a successful
registration with MHI. Improve the design by checking for the number
of IRQs available sooner within the mhi_regsiter_controller() API as
it is required to be specified by the controller.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
If the host receives a mission mode event and by the time it can get
to processing it, the register accesses fail implying a connectivity
error, MHI should move to an error state. This helps avoid longer wait
times from a synchronous power up perspective and accurately reflects
the MHI execution environment and power management states.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Correct the "error_read" label to say "error_ready_state" as that
is the appropriate usage of the label.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Move MHI to a firmware download error state for a failure to find
the firmware files or to load SBL or EBL image using BHI/BHIe. This
helps detect an error state sooner and shortens the wait for a
synchronous power up timeout.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
If an mhi_power_down() is initiated after the device has entered
RDDM and a status callback was provided for it, it is possible
that another BHI interrupt fires while waiting for the MHI
RESET to be cleared. If that happens, MHI host would have moved
a "disabled" execution environment and the check to allow sending
an RDDM status callback will pass when it is should not. Add a
check to see if MHI is in an active state before proceeding.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
In some cases, the entry of device to RDDM execution environment
can occur after a significant amount of time has elapsed and a
SYS_ERROR state change event has already arrived. This can result
in scenarios where MHI controller and client drivers are unaware
of the error state of the device. Remove the check for rddm_image
when processing the SYS_ERROR state change as it is present in
mhi_pm_sys_err_handler() already and prevent further activity
until the expected RDDM execution environment change occurs or
the controller driver decides further action.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
MHI client drivers can request a device wake even if the device
may be in an error state or undergoing a shutdown. To prevent
unnecessary device wake processing, check for the device state
and bail out early so that the clients are made aware of the
device state sooner.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
MHI work is currently scheduled on the global/system workqueue and can
encounter delays on a stressed system. To avoid those unforeseen
delays which can hamper bootup or shutdown times, use a dedicated high
priority workqueue instead of the global/system workqueue.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
mhi_fw_load_sbl() function is currently used to transfer SBL or EDL
images over BHI (Boot Host Interface). Same goes with mhi_fw_load_amss()
which uses BHIe. However, the contents of these functions do not
indicate support for a specific set of images. Since these can be used
for any image download over BHI or BHIe, rename them based on the
protocol used.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
If MHI is unable to determine the execution environment during
the panic path, host must skip the RDDM download. This can happen
if the BHI offset read or the BHI_EXECENV register read fails
indicating that the underlying transport is unresponsive. Hence,
there is no need to trigger an RDDM using SYSERR or request an
SOC reset.
Suggested-by: Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
mhi_download_rddm_img() uses a shorter version of the word image.
Expand it and rename the function to mhi_download_rddm_image().
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
