| Age | Commit message (Collapse) | Author |
|---|
|
If we delay sending End Transfer for Setup TRB to be prepared, we need
to check if the End Transfer was in preparation for a driver
teardown/soft-disconnect. In those cases, just send the End Transfer
command without delay.
In the case of soft-disconnect, there's a very small chance the command
may not go through immediately. But should it happen, the Setup TRB will
be prepared during the polling of the controller halted state, allowing
the command to go through then.
In the case of disabling endpoint due to reconfiguration (e.g.
set_interface(alt-setting) or usb reset), then it's driven by the host.
Typically the host wouldn't immediately cancel the control request and
send another control transfer to trigger the End Transfer command
timeout.
Fixes: 4db0fbb60136 ("usb: dwc3: gadget: Don't delay End Transfer on delayed_status")
Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/f1617a323e190b9cc408fb8b65456e32b5814113.1670546756.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The newly added gpio consumer calls cause a build failure in configurations
that fail to include the right header implicitly:
drivers/usb/dwc3/dwc3-xilinx.c: In function 'dwc3_xlnx_init_zynqmp':
drivers/usb/dwc3/dwc3-xilinx.c:207:22: error: implicit declaration of function 'devm_gpiod_get_optional'; did you mean 'devm_clk_get_optional'? [-Werror=implicit-function-declaration]
207 | reset_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW);
| ^~~~~~~~~~~~~~~~~~~~~~~
| devm_clk_get_optional
Fixes: ca05b38252d7 ("usb: dwc3: xilinx: Add gpio-reset support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230103121755.956027-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The clang build reports this error
fs/udf/inode.c:805:6: error: variable 'newblock' is used uninitialized whenever 'if' condition is true [-Werror,-Wsometimes-uninitialized]
if (*err < 0)
^~~~~~~~
newblock is never set before error handling jump.
Initialize newblock to 0 and remove redundant settings.
Fixes: d8b39db5fab8 ("udf: Handle error when adding extent to a file")
Reported-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Message-Id: <20221230175341.1629734-1-trix@redhat.com>
|
|
When extending the last extent in the file within the last block, we
wrongly computed the length of the last extent. This is mostly a
cosmetical problem since the extent does not contain any data and the
length will be fixed up by following operations but still.
Fixes: 1f3868f06855 ("udf: Fix extending file within last block")
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
This unexpected behavior is observed:
node 1 | node 2
------ | ------
link is established | link is established
reboot | link is reset
up | send discovery message
receive discovery message |
link is established | link is established
send discovery message |
| receive discovery message
| link is reset (unexpected)
| send reset message
link is reset |
It is due to delayed re-discovery as described in function
tipc_node_check_dest(): "this link endpoint has already reset
and re-established contact with the peer, before receiving a
discovery message from that node."
However, commit 598411d70f85 has changed the condition for calling
tipc_node_link_down() which was the acceptance of new media address.
This commit fixes this by restoring the old and correct behavior.
Fixes: 598411d70f85 ("tipc: make resetting of links non-atomic")
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the connection setup of client calls to the I/O thread so that a whole
load of locking and barrierage can be eliminated. This necessitates the
app thread waiting for connection to complete before it can begin
encrypting data.
This also completes the fix for a race that exists between call connection
and call disconnection whereby the data transmission code adds the call to
the peer error distribution list after the call has been disconnected (say
by the rxrpc socket getting closed).
The fix is to complete the process of moving call connection, data
transmission and call disconnection into the I/O thread and thus forcibly
serialising them.
Note that the issue may predate the overhaul to an I/O thread model that
were included in the merge window for v6.2, but the timing is very much
changed by the change given below.
Fixes: cf37b5987508 ("rxrpc: Move DATA transmission into call processor work item")
Reported-by: syzbot+c22650d2844392afdcfd@syzkaller.appspotmail.com
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
Move the management of the client connection cache to the I/O thread rather
than managing it from the namespace as an aggregate across all the local
endpoints within the namespace.
This will allow a load of locking to be got rid of in a future patch as
only the I/O thread will be looking at the this.
The downside is that the total number of cached connections on the system
can get higher because the limit is now per-local rather than per-netns.
We can, however, keep the number of client conns in use across the entire
netfs and use that to reduce the expiration time of idle connection.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
All the setters of call->state are now in the I/O thread and thus the state
lock is now unnecessary.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
Move the call state changes that are made in rxrpc_recvmsg() to the I/O
thread. This means that, thenceforth, only the I/O thread does this and
the call state lock can be removed.
This requires the Rx phase to be ended when the last packet is received,
not when it is processed.
Since this now changes the rxrpc call state to SUCCEEDED before we've
consumed all the data from it, rxrpc_kernel_check_life() mustn't say the
call is dead until the recvmsg queue is empty (unless the call has failed).
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
Move all the call state changes that are made in rxrpc_sendmsg() to the I/O
thread. This is a step towards removing the call state lock.
This requires the switch to the RXRPC_CALL_CLIENT_AWAIT_REPLY and
RXRPC_CALL_SERVER_SEND_REPLY states to be done when the last packet is
decanted from ->tx_sendmsg to ->tx_buffer in the I/O thread, not when it is
added to ->tx_sendmsg by sendmsg().
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
Wrap accesses to get the state of a call from outside of the I/O thread in
a single place so that the barrier needed to order wrt the error code and
abort code is in just that place.
Also use a barrier when setting the call state and again when reading the
call state such that the auxiliary completion info (error code, abort code)
can be read without taking a read lock on the call state lock.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
Split out the functions that change the state of an rxrpc call into their
own file. The idea being to remove anything to do with changing the state
of a call directly from the rxrpc sendmsg() and recvmsg() paths and have
all that done in the I/O thread only, with the ultimate aim of removing the
state lock entirely. Moving the code out of sendmsg.c and recvmsg.c makes
that easier to manage.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
Use the information now stored in struct rxrpc_call to configure the
connection bundle and thence the connection, rather than using the
rxrpc_conn_parameters struct.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
Offload the completion of the challenge/response cycle on a service
connection to the I/O thread. After the RESPONSE packet has been
successfully decrypted and verified by the work queue, offloading the
changing of the call states to the I/O thread makes iteration over the
conn's channel list simpler.
Do this by marking the RESPONSE skbuff and putting it onto the receive
queue for the I/O thread to collect. We put it on the front of the queue
as we've already received the packet for it.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
Make the set of connection IDs per local endpoint so that endpoints don't
cause each other's connections to get dismissed.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
Tidy up the abort generation infrastructure in the following ways:
(1) Create an enum and string mapping table to list the reasons an abort
might be generated in tracing.
(2) Replace the 3-char string with the values from (1) in the places that
use that to log the abort source. This gets rid of a memcpy() in the
tracepoint.
(3) Subsume the rxrpc_rx_eproto tracepoint with the rxrpc_abort tracepoint
and use values from (1) to indicate the trace reason.
(4) Always make a call to an abort function at the point of the abort
rather than stashing the values into variables and using goto to get
to a place where it reported. The C optimiser will collapse the calls
together as appropriate. The abort functions return a value that can
be returned directly if appropriate.
Note that this extends into afs also at the points where that generates an
abort. To aid with this, the afs sources need to #define
RXRPC_TRACE_ONLY_DEFINE_ENUMS before including the rxrpc tracing header
because they don't have access to the rxrpc internal structures that some
of the tracepoints make use of.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
Clean up connection abort, using the connection state_lock to gate access
to change that state, and use an rxrpc_call_completion value to indicate
the difference between local and remote aborts as these can be pasted
directly into the call state.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
Provide a means by which an event notification can be sent to a connection
through such that the I/O thread can pick it up and handle it rather than
doing it in a separate workqueue.
This is then used to move the deferred final ACK of a call into the I/O
thread rather than a separate work queue as part of the drive to do all
transmission from the I/O thread.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
Only perform call disconnection in the I/O thread to reduce the locking
requirement.
This is the first part of a fix for a race that exists between call
connection and call disconnection whereby the data transmission code adds
the call to the peer error distribution list after the call has been
disconnected (say by the rxrpc socket getting closed).
The fix is to complete the process of moving call connection, data
transmission and call disconnection into the I/O thread and thus forcibly
serialising them.
Note that the issue may predate the overhaul to an I/O thread model that
were included in the merge window for v6.2, but the timing is very much
changed by the change given below.
Fixes: cf37b5987508 ("rxrpc: Move DATA transmission into call processor work item")
Reported-by: syzbot+c22650d2844392afdcfd@syzkaller.appspotmail.com
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
Only set the abort call completion state in the I/O thread and only
transmit ABORT packets from there. rxrpc_abort_call() can then be made to
actually send the packet.
Further, ABORT packets should only be sent if the call has been exposed to
the network (ie. at least one attempted DATA transmission has occurred for
it).
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
Call the rxrpc_conn_retransmit_call() directly from rxrpc_input_packet()
rather than calling it via connection event handling.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
Make the local endpoint and it's I/O thread hold a reference on a connected
call until that call is disconnected. Without this, we're reliant on
either the AF_RXRPC socket to hold a ref (which is dropped when the call is
released) or a queued work item to hold a ref (the work item is being
replaced with the I/O thread).
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
Stash the network namespace pointer in the rxrpc_local struct in addition
to a pointer to the rxrpc-specific net namespace info. Use this to remove
some places where the socket is passed as a parameter.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
Only gvt-fixes:
- debugfs fixes (Zhenyu)
- fix up for vgpu status (Zhi)
- double free fix in split_2MB_gtt_entry (Zheng)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/Y7cszBkLRvAy6uao@intel.com
|
|
Panel is 800x1280 but mounted on a detachable form factor sideways.
Signed-off-by: Patrick Thompson <ptf@google.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20221220205826.178008-1-ptf@google.com
|
|
After commit 5f217ccd520f ("fotg210-udc: Support optional external PHY"),
the error code is re-assigned to 0 in fotg210_udc_probe(), if allocate or
map memory fails after the assignment, it can't return an error code. Set
the error code to -ENOMEM to fix this problem.
Fixes: 5f217ccd520f ("fotg210-udc: Support optional external PHY")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20221230065427.944586-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This modem has 7 interfaces, 5 of them are serial interfaces and are
driven by cdc_acm, while 2 of them are wwan interfaces and are driven
by cdc_ether:
If 0: Abstract (modem)
If 1: Abstract (modem)
If 2: Abstract (modem)
If 3: Abstract (modem)
If 4: Abstract (modem)
If 5: Ethernet Networking
If 6: Ethernet Networking
Without this change, the 2 network interfaces will be named to usb0
and usb1, our QA think the names are confusing and filed a bug on it.
After applying this change, the name will be wwan0 and wwan1, and
they could work well with modem manager.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20230105034249.10433-1-hui.wang@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In current driver, MAC will always enable 2ns delay in RGMII mode,
but that's not the correct usage.
Remove the dwmac_fix_mac_speed() in driver, and recommend "rgmii-id"
for phy-mode in device tree.
Fixes: f2d356a6ab71 ("stmmac: dwmac-mediatek: add support for mt8195")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As per the downstream driver, gx gbif halt is required only during
recovery sequence. So lets avoid it during regular rpm suspend.
Signed-off-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/515279/
Link: https://lore.kernel.org/r/20221216223253.1.Ice9c47bfeb1fddb8dc377a3491a043a3ee7fca7d@changeid
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
So far the adreno quirks have all been assigned with an OR operator,
which is problematic, because they were assigned consecutive integer
values, which makes checking them with an AND operator kind of no bueno..
Switch to using BIT(n) so that only the quirks that the programmer chose
are taken into account when evaluating info->quirks & ADRENO_QUIRK_...
Fixes: 370063ee427a ("drm/msm/adreno: Add A540 support")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/516456/
Link: https://lore.kernel.org/r/20230102100201.77286-1-konrad.dybcio@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull thermal control fix from Rafael Wysocki:
"Add a missing sysfs attribute to the int340x thermal driver (Srinivas
Pandruvada)"
* tag 'thermal-6.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
thermal: int340x: Add missing attribute for data rate base
|
|
Fix another oops reproducible when rebooting the board with the Adreno
GPU working in the headless mode (e.g. iMX platforms).
Unable to handle kernel NULL pointer dereference at virtual address 00000000 when read
[00000000] *pgd=74936831, *pte=00000000, *ppte=00000000
Internal error: Oops: 17 [#1] ARM
CPU: 0 PID: 51 Comm: reboot Not tainted 6.2.0-rc1-dirty #11
Hardware name: Freescale i.MX53 (Device Tree Support)
PC is at msm_atomic_commit_tail+0x50/0x970
LR is at commit_tail+0x9c/0x188
pc : [<c06aa430>] lr : [<c067a214>] psr: 600e0013
sp : e0851d30 ip : ee4eb7eb fp : 00090acc
r10: 00000058 r9 : c2193014 r8 : c4310000
r7 : c4759380 r6 : 07bef61d r5 : 00000000 r4 : 00000000
r3 : c44cc440 r2 : 00000000 r1 : 00000000 r0 : 00000000
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
Control: 10c5387d Table: 74910019 DAC: 00000051
Register r0 information: NULL pointer
Register r1 information: NULL pointer
Register r2 information: NULL pointer
Register r3 information: slab kmalloc-1k start c44cc400 pointer offset 64 size 1024
Register r4 information: NULL pointer
Register r5 information: NULL pointer
Register r6 information: non-paged memory
Register r7 information: slab kmalloc-128 start c4759380 pointer offset 0 size 128
Register r8 information: slab kmalloc-2k start c4310000 pointer offset 0 size 2048
Register r9 information: non-slab/vmalloc memory
Register r10 information: non-paged memory
Register r11 information: non-paged memory
Register r12 information: non-paged memory
Process reboot (pid: 51, stack limit = 0xc80046d9)
Stack: (0xe0851d30 to 0xe0852000)
1d20: c4759380 fbd77200 000005ff 002b9c70
1d40: c4759380 c4759380 00000000 07bef61d 00000600 c0d6fe7c c2193014 00000058
1d60: 00090acc c067a214 00000000 c4759380 c4310000 00000000 c44cc854 c067a89c
1d80: 00000000 00000000 00000000 c4310468 00000000 c4759380 c4310000 c4310468
1da0: c4310470 c0643258 c4759380 00000000 00000000 c0c4ee24 00000000 c44cc810
1dc0: 00000000 c0c4ee24 00000000 c44cc810 00000000 0347d2a8 e0851e00 e0851e00
1de0: c4759380 c067ad20 c4310000 00000000 c44cc810 c27f8718 c44cc854 c067adb8
1e00: c4933000 00000002 00000001 00000000 00000000 c2130850 00000000 c2130854
1e20: c25fc488 00000000 c0ff162c 00000000 00000001 00000002 00000000 00000000
1e40: c43102c0 c43102c0 00000000 0347d2a8 c44cc810 c44cc814 c2133da8 c06d1a60
1e60: 00000000 00000000 00079028 c2012f24 fee1dead c4933000 00000058 c01431e4
1e80: 01234567 c0143a20 00000000 00000000 00000000 00000000 00000000 00000000
1ea0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1ec0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1ee0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1f00: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1f20: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1f40: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1f60: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1f80: 00000000 00000000 00000000 0347d2a8 00000002 00000004 00000078 00000058
1fa0: c010028c c0100060 00000002 00000004 fee1dead 28121969 01234567 00079028
1fc0: 00000002 00000004 00000078 00000058 0002fdc5 00000000 00000000 00090acc
1fe0: 00000058 becc9c64 b6e97e05 b6e0e5f6 600e0030 fee1dead 00000000 00000000
msm_atomic_commit_tail from commit_tail+0x9c/0x188
commit_tail from drm_atomic_helper_commit+0x160/0x188
drm_atomic_helper_commit from drm_atomic_commit+0xac/0xe0
drm_atomic_commit from drm_atomic_helper_disable_all+0x1b0/0x1c0
drm_atomic_helper_disable_all from drm_atomic_helper_shutdown+0x88/0x140
drm_atomic_helper_shutdown from device_shutdown+0x16c/0x240
device_shutdown from kernel_restart+0x38/0x90
kernel_restart from __do_sys_reboot+0x174/0x224
__do_sys_reboot from ret_fast_syscall+0x0/0x1c
Exception stack(0xe0851fa8 to 0xe0851ff0)
1fa0: 00000002 00000004 fee1dead 28121969 01234567 00079028
1fc0: 00000002 00000004 00000078 00000058 0002fdc5 00000000 00000000 00090acc
1fe0: 00000058 becc9c64 b6e97e05 b6e0e5f6
Code: 15922088 1184421c e1500003 1afffff8 (e5953000)
---[ end trace 0000000000000000 ]---
Fixes: 0a58d2ae572a ("drm/msm: Make .remove and .shutdown HW shutdown consistent")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/516909/
Link: https://lore.kernel.org/r/20230105014743.1478110-1-dmitry.baryshkov@linaro.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
|
|
There's a typo in describing the core clock as an 'escape' clock. The
accurate description is 'core'.
Fixes: 4dbe55c97741 ("dt-bindings: msm: dsi: add yaml schemas for DSI bindings")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/515938/
Link: https://lore.kernel.org/r/20221223021025.1646636-4-bryan.odonoghue@linaro.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
|
|
power-domain is required for the sc7180 dispcc GDSC but not every qcom SoC
has a similar dependency for example the apq8064.
Most Qcom SoC's using mdss-dsi-ctrl seem to have the ability to
power-collapse the MDP without collapsing DSI.
For example the qcom vendor kernel commit for apq8084, msm8226, msm8916,
msm8974.
https://review.carbonrom.org/plugins/gitiles/CarbonROM/android_kernel_oneplus_msm8994/+/7b5c011a770daa2811778937ed646237a28a8694
"ARM: dts: msm: add mdss gdsc supply to dsi controller device
It is possible for the DSI controller to be active when MDP is
power collapsed. DSI controller needs to have it's own vote for
mdss gdsc to ensure that gdsc remains on in such cases."
This however doesn't appear to be the case for the apq8064 so we shouldn't
be marking power-domain as required in yaml checks.
Fixes: 4dbe55c97741 ("dt-bindings: msm: dsi: add yaml schemas for DSI bindings")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/515958/
Link: https://lore.kernel.org/r/20221223021025.1646636-3-bryan.odonoghue@linaro.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
|
|
The existing msm8916.dtsi does not depend on nor require operating points.
Fixes: 4dbe55c97741 ("dt-bindings: msm: dsi: add yaml schemas for DSI bindings")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/515940/
Link: https://lore.kernel.org/r/20221223021025.1646636-2-bryan.odonoghue@linaro.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from bpf, wifi, and netfilter.
Current release - regressions:
- bpf: fix nullness propagation for reg to reg comparisons, avoid
null-deref
- inet: control sockets should not use current thread task_frag
- bpf: always use maximal size for copy_array()
- eth: bnxt_en: don't link netdev to a devlink port for VFs
Current release - new code bugs:
- rxrpc: fix a couple of potential use-after-frees
- netfilter: conntrack: fix IPv6 exthdr error check
- wifi: iwlwifi: fw: skip PPAG for JF, avoid FW crashes
- eth: dsa: qca8k: various fixes for the in-band register access
- eth: nfp: fix schedule in atomic context when sync mc address
- eth: renesas: rswitch: fix getting mac address from device tree
- mobile: ipa: use proper endpoint mask for suspend
Previous releases - regressions:
- tcp: add TIME_WAIT sockets in bhash2, fix regression caught by
Jiri / python tests
- net: tc: don't intepret cls results when asked to drop, fix
oob-access
- vrf: determine the dst using the original ifindex for multicast
- eth: bnxt_en:
- fix XDP RX path if BPF adjusted packet length
- fix HDS (header placement) and jumbo thresholds for RX packets
- eth: ice: xsk: do not use xdp_return_frame() on tx_buf->raw_buf,
avoid memory corruptions
Previous releases - always broken:
- ulp: prevent ULP without clone op from entering the LISTEN status
- veth: fix race with AF_XDP exposing old or uninitialized
descriptors
- bpf:
- pull before calling skb_postpull_rcsum() (fix checksum support
and avoid a WARN())
- fix panic due to wrong pageattr of im->image (when livepatch and
kretfunc coexist)
- keep a reference to the mm, in case the task is dead
- mptcp: fix deadlock in fastopen error path
- netfilter:
- nf_tables: perform type checking for existing sets
- nf_tables: honor set timeout and garbage collection updates
- ipset: fix hash:net,port,net hang with /0 subnet
- ipset: avoid hung task warning when adding/deleting entries
- selftests: net:
- fix cmsg_so_mark.sh test hang on non-x86 systems
- fix the arp_ndisc_evict_nocarrier test for IPv6
- usb: rndis_host: secure rndis_query check against int overflow
- eth: r8169: fix dmar pte write access during suspend/resume with
WOL
- eth: lan966x: fix configuration of the PCS
- eth: sparx5: fix reading of the MAC address
- eth: qed: allow sleep in qed_mcp_trace_dump()
- eth: hns3:
- fix interrupts re-initialization after VF FLR
- fix handling of promisc when MAC addr table gets full
- refine the handling for VF heartbeat
- eth: mlx5:
- properly handle ingress QinQ-tagged packets on VST
- fix io_eq_size and event_eq_size params validation on big endian
- fix RoCE setting at HCA level if not supported at all
- don't turn CQE compression on by default for IPoIB
- eth: ena:
- fix toeplitz initial hash key value
- account for the number of XDP-processed bytes in interface stats
- fix rx_copybreak value update
Misc:
- ethtool: harden phy stat handling against buggy drivers
- docs: netdev: convert maintainer's doc from FAQ to a normal
document"
* tag 'net-6.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (112 commits)
caif: fix memory leak in cfctrl_linkup_request()
inet: control sockets should not use current thread task_frag
net/ulp: prevent ULP without clone op from entering the LISTEN status
qed: allow sleep in qed_mcp_trace_dump()
MAINTAINERS: Update maintainers for ptp_vmw driver
usb: rndis_host: Secure rndis_query check against int overflow
net: dpaa: Fix dtsec check for PCS availability
octeontx2-pf: Fix lmtst ID used in aura free
drivers/net/bonding/bond_3ad: return when there's no aggregator
netfilter: ipset: Rework long task execution when adding/deleting entries
netfilter: ipset: fix hash:net,port,net hang with /0 subnet
net: sparx5: Fix reading of the MAC address
vxlan: Fix memory leaks in error path
net: sched: htb: fix htb_classify() kernel-doc
net: sched: cbq: dont intepret cls results when asked to drop
net: sched: atm: dont intepret cls results when asked to drop
dt-bindings: net: marvell,orion-mdio: Fix examples
dt-bindings: net: sun8i-emac: Add phy-supply property
net: ipa: use proper endpoint mask for suspend
selftests: net: return non-zero for failures reported in arp_ndisc_evict_nocarrier
...
|
|
If the get_user(x, ptr) has x as a pointer, then the setting
of (x) = 0 is going to produce the following sparse warning,
so fix this by forcing the type of 'x' when access_ok() fails.
fs/aio.c:2073:21: warning: Using plain integer as NULL pointer
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Reviewed-by: Palmer Dabbelt <palmer@rivosinc.com>
Link: https://lore.kernel.org/r/20221229170545.718264-1-ben-linux@fluff.org
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
In the compressed instruction extension, c.jr, c.jalr, c.mv, and c.add
is encoded the following way (each instruction is 16b):
---+-+-----------+-----------+--
100 0 rs1[4:0]!=0 00000 10 : c.jr
100 1 rs1[4:0]!=0 00000 10 : c.jalr
100 0 rd[4:0]!=0 rs2[4:0]!=0 10 : c.mv
100 1 rd[4:0]!=0 rs2[4:0]!=0 10 : c.add
The following logic is used to decode c.jr and c.jalr:
insn & 0xf007 == 0x8002 => instruction is an c.jr
insn & 0xf007 == 0x9002 => instruction is an c.jalr
When 0xf007 is used to mask the instruction, c.mv can be incorrectly
decoded as c.jr, and c.add as c.jalr.
Correct the decoding by changing the mask from 0xf007 to 0xf07f.
Fixes: c22b0bcb1dd0 ("riscv: Add kprobes supported")
Signed-off-by: Björn Töpel <bjorn@rivosinc.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Guo Ren <guoren@kernel.org>
Link: https://lore.kernel.org/r/20230102160748.1307289-1-bjorn@kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fixes from Bartosz Golaszewski:
"A reference leak fix, two fixes for using uninitialized variables and
more drivers converted to using immutable irqchips:
- fix a reference leak in gpio-sifive
- fix a potential use of an uninitialized variable in core gpiolib
- fix a potential use of an uninitialized variable in gpio-pca953x
- make GPIO irqchips immutable in gpio-pmic-eic-sprd, gpio-eic-sprd
and gpio-sprd"
* tag 'gpio-fixes-for-v6.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpio: sifive: Fix refcount leak in sifive_gpio_probe
gpio: sprd: Make the irqchip immutable
gpio: pmic-eic-sprd: Make the irqchip immutable
gpio: eic-sprd: Make the irqchip immutable
gpio: pca953x: avoid to use uninitialized value pinctrl
gpiolib: Fix using uninitialized lookup-flags on ACPI platforms
|
|
When sg_alloc_append_table_from_pages() calls to pages_are_mergeable() in
its 'sgt_append->prv' flow to check whether it can merge contiguous pages
into the last SG, it passes the page arguments in the wrong order.
The first parameter should be the next candidate page to be merged to
the last page and not the opposite.
The current code leads to a corrupted SG which resulted in OOPs and
unexpected errors when non-contiguous pages are merged wrongly.
Fix to pass the page parameters in the right order.
Fixes: 1567b49d1a40 ("lib/scatterlist: add check when merging zone device pages")
Link: https://lore.kernel.org/r/20230105112339.107969-1-yishaih@nvidia.com
Signed-off-by: Yishai Hadas <yishaih@nvidia.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
When the fence can't be added we need to drop the reference.
Suggested-by: Bert Karwatzki <spasswolf@web.de>
Signed-off-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230105111703.52695-2-christian.koenig@amd.com
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Luben Tuikov <luben.tuikov@amd.com>
|
|
drm_sched_job_add_dependency() consumes the references of the gang
members. Only triggered by mesh shaders.
Signed-off-by: Christian König <christian.koenig@amd.com>
Fixes: 1728baa7e4e6 ("drm/amdgpu: use scheduler dependencies for CS")
Tested-by: Mike Lothian <mike@fireburn.co.uk>
Tested-by: Bert Karwatzki <spasswolf@web.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230105111703.52695-1-christian.koenig@amd.com
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Luben Tuikov <luben.tuikov@amd.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev
Pull fbdev fixes from Helge Deller:
- Fix Matrox G200eW initialization failure
- Fix build failure of offb driver when built as module
- Optimize stack usage in omapfb
* tag 'fbdev-for-6.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev:
fbdev: omapfb: avoid stack overflow warning
fbdev: matroxfb: G200eW: Increase max memory from 1 MB to 16 MB
fbdev: atyfb: use strscpy() to instead of strncpy()
fbdev: omapfb: use strscpy() to instead of strncpy()
fbdev: make offb driver tristate
|
|
Then we are able to set a new ppt limit via the hwmon interface(power1_cap).
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.0.x, 6.1.x
|
|
Correct the reference clock as 25Mhz for SMU13 fan speed calculation.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.0.x, 6.1.x
|
|
As mentioned in the corresponding DT binding commit, the naming scheme
for delay properties includes "delay" in the name, so let's keep that
consistent.
Fixes: 33a2fde5f77b ("spi: Introduce spi-cs-setup-ns property")
Signed-off-by: Hector Martin <marcan@marcan.st>
Link: https://lore.kernel.org/r/20230104093631.15611-3-marcan@marcan.st
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Other delay values follow the delay-ns naming convention, so unify the
newly introduced spi-cs-setup-ns property for consistency.
Also fix a typo while we're here.
Fixes: f6c911f3308c ("spi: dt-bindings: Introduce spi-cs-setup-ns property")
Signed-off-by: Hector Martin <marcan@marcan.st>
Link: https://lore.kernel.org/r/20230104093631.15611-2-marcan@marcan.st
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The parameter "max" of SOC_SINGLE_SX_TLV() means the number of steps
rather than maximum value. This patch corrects the minimum value to -8
and the number of steps to 15.
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Acked-by: Shengjiu Wang <shengjiu.wang@gmail.com>
Link: https://lore.kernel.org/r/20230104025754.3019235-1-chancel.liu@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Now that the SRCU Kconfig option is unconditionally selected, there is
no longer any point in selecting it. Therefore, remove the "select SRCU"
Kconfig statements.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: linux-block@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
In xfs_extent_busy_update_extent() case 6 and 7, whenever bno is modified on
extent busy, the relavent length has to be modified accordingly.
Signed-off-by: Wengang Wang <wen.gang.wang@oracle.com>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
|
