| Age | Commit message (Collapse) | Author |
|---|
|
Historically, both the touch and pad tools would have shared the
'BTN_TOOL_FINGER' type. Any time you needed to distinguish the two, you
had to use some other bit of knowledge (e.g. that the pad was on the same
interface as the pen, and thus 'touch_max' would be zero).
To make these checks more readable, we introduce WACOM_DEVICETYPE_PAD.
Although we still have to rely on other bits of knowledge to set this
bit on the right interface (since it cannot be detected from the HID
descriptor), it can be done just once inside 'wacom_setup_device_quirks'.
This patch introduces no functional changes.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The USB devices that this driver has historically supported segregate the
pen and touch portions of the tablet. Oftentimes the segregation would be
done at the interface level, though on occasion (e.g. Cintiq 24HDT) the
tablet would combine two totally independent USB devices behind an internal
USB hub. Because pen and touch never shared the same interface, it made
sense for the 'device_type' to store a single value: "pen" or "touch".
Recently, however, some I2C devices have been created which combine the
two. A first step to accomodating this is to expand 'device_type' so that
it can represent two (or potentially more) types simultaneously. To do
this, we treat it as a bitfield and set/check individual bits rather
than using the '=' and '==' operators.
This should not result in any functional change since no supported devices
(that I'm aware of, at least) have HID descriptors that indicate both
pen and touch reports on a single interface.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
A little bit of cleanup work for 'wacom_update_name' to make it easier on
the eyes. Creates a temporary 'name' variable on which we'll perform our
edits. Once the name is in its final form, it will be copied (with
appropriate suffix) to 'wacom_wac->name' and 'wacom_wac->pad_name'.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/core
Pull perf/core improvements and fixes from Arnaldo Carvalho de Melo:
User visible changes:
- List perf probes to stdout. (Masami Hiramatsu)
- Return error when none of the requested probes were
installed. (Masami Hiramatsu)
- Cut off the gcc optimization postfixes from
function name in 'perf probe'. (Masami Hiramatsu)
- Allow disabling/enabling events dynamicly in 'perf top':
a 'perf top' session can instantly become a 'perf report'
one, i.e. going from dynamic analysis to a static one,
returning to a dynamic one is possible, to toogle the
modes, just press CTRL+z. (Arnaldo Carvalho de Melo)
- Greatly speed up 'perf probe --list' by caching debuginfo.
(Masami Hiramatsu)
- Fix 'perf trace' race condition at the end of started
workloads. (Sukadev Bhattiprolu)
- Fix a problem when opening old perf.data with different
byte order. (Wang Nan)
Infrastructure changes:
- Replace map->referenced & maps->removed_maps with
map->refcnt. (Arnaldo Carvalho de Melo)
- Introduce the xyarray__reset() function. (Jiri Olsa)
- Add thread_map__(alloc|realloc)() helpers. (Jiri Olsa)
- Move perf_evsel__(alloc|free|reset)_counts into stat object. (Jiri Olsa)
- Introduce perf_counts__(new|delete|reset)() functions. (Jiri Olsa)
- Ignore .config-detected in .gitignore. (Wang Nan)
- Move libtraceevent dynamic list to separated LDFLAGS
variable. (Wang Nan)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The fix in d151832650ed9 (time: Move clock_was_set_seq update
before updating shadow-timekeeper) was unfortunately incomplete.
The main gist of that change was to do the shadow-copy update
last, so that any state changes were properly duplicated, and
we wouldn't accidentally have stale data in the shadow.
Unfortunately in the main update_wall_time() logic, we update
use the shadow-timekeeper to calculate the next update values,
then while holding the lock, copy the shadow-timekeeper over,
then call timekeeping_update() to do some additional
bookkeeping, (skipping the shadow mirror). The bug with this is
the additional bookkeeping isn't all read-only, and some
changes timkeeper state. Thus we might then overwrite this state
change on the next update.
To avoid this problem, do the timekeeping_update() on the
shadow-timekeeper prior to copying the full state over to
the real-timekeeper.
This avoids problems with both the clock_was_set_seq and
next_leap_ktime being overwritten and possibly the
fast-timekeepers as well.
Many thanks to Prarit for his rigorous testing, which discovered
this problem, along with Prarit and Daniel's work validating this
fix.
Reported-by: Prarit Bhargava <prarit@redhat.com>
Tested-by: Prarit Bhargava <prarit@redhat.com>
Tested-by: Daniel Bristot de Oliveira <bristot@redhat.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Jiri Bohac <jbohac@suse.cz>
Cc: Ingo Molnar <mingo@kernel.org>
Link: http://lkml.kernel.org/r/1434560753-7441-1-git-send-email-john.stultz@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
CLOCK_EVT_MODE_* macros are present for backward compatibility (as most
of the drivers are still using old ->set_mode() interface).
These macro's shouldn't be used anymore in code, that is common to both
driver interfaces, i.e. ->set_mode() and ->set_state_*().
Drivers implementing ->set_state_*() interface, which have their
clkevt->mode set to 0 (clkevt device structures are normally globally
defined), will not participate in suspend/resume as they will always be
marked as UNUSED.
Fix this by checking state of the clockevent device instead of mode,
which is updated for both the interfaces.
Fixes: ac34ad27fc16 ("clockevents: Do not suspend/resume if unused")
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: linaro-kernel@lists.linaro.org
Cc: alexandre.belloni@free-electrons.com
Cc: sylvain.rochet@finsecur.com
Link: http://lkml.kernel.org/r/a1964eef6e8a47d02b1ff9083c6c91f73f0ff643.1434537215.git.viresh.kumar@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
On systems with CONFIG_PREEMPT=n, under certain circumstances, mmcqd
can continuously process requests for several seconds without blocking,
triggering the soft lockup watchdog. For example, this can happen if
mmcqd runs on the CPU which services the controller's interrupt, and
a process on a different CPU continuously writes to the MMC block
device.
NMI watchdog: BUG: soft lockup - CPU#0 stuck for 22s! [mmcqd/0:664]
CPU: 0 PID: 664 Comm: mmcqd/0 Not tainted 4.1.0-rc7+ #4
PC is at _raw_spin_unlock_irqrestore+0x24/0x28
LR is at mmc_start_request+0x104/0x134
...
[<805112a8>] (_raw_spin_unlock_irqrestore) from [<803db664>] (mmc_start_request+0x104/0x134)
[<803db664>] (mmc_start_request) from [<803dc008>] (mmc_start_req+0x274/0x394)
[<803dc008>] (mmc_start_req) from [<803eb2c4>] (mmc_blk_issue_rw_rq+0xd0/0xb98)
[<803eb2c4>] (mmc_blk_issue_rw_rq) from [<803ebe8c>] (mmc_blk_issue_rq+0x100/0x470)
[<803ebe8c>] (mmc_blk_issue_rq) from [<803ecab8>] (mmc_queue_thread+0xd0/0x170)
[<803ecab8>] (mmc_queue_thread) from [<8003fd14>] (kthread+0xe0/0xfc)
[<8003fd14>] (kthread) from [<8000f768>] (ret_from_fork+0x14/0x2c)
Fix it by adding a cond_resched() in the request handling loop so that
other processes get a chance to run.
Signed-off-by: Rabin Vincent <rabin.vincent@axis.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add PM support for Mediatek MMC driver
Save/restore registers when PM
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add Mediatek MMC driver code
Support eMMC/SD/SDIO
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This code is no longer used now that mach-msm has been removed.
Delete it.
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: David Brown <davidb@codeaurora.org>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing filter fix from Steven Rostedt:
"Vince Weaver reported a warning when he added perf event filters into
his fuzzer tests. There's a missing check of balanced operations when
parenthesis are used, and this triggers a WARN_ON() and when reading
the failure, the filter reports no failure occurred.
The operands were not being checked if they match, this adds that"
* tag 'trace-fix-filter-4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Have filter check for balanced ops
|
|
Pull kvm bugfix from Marcelo Tosatti:
"Rrestore APIC migration functionality"
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: fix lapic.timer_mode on restore
|
|
Since when we start discussions about the usage Media Controller for
complex hardware, one thing become clear: the way it is, MC fails to
map anything different than capture/output/m2m video-only streaming.
The point is that MC has entities named as devnodes, but the only
devnode used (before the DVB patches) is MEDIA_ENT_T_DEVNODE_V4L.
Due to the way MC got implemented, however, this entity actually
doesn't represent the devnode, but the hardware I/O engine that
receives data via DMA.
By coincidence, such DMA is associated with the V4L device node
on webcam hardware, but this is not true even for other V4L2
devices. For example, on USB hardware, the DMA is done via the
USB controller. The data passes though a in-kernel filter that
strips off the URB headers. Other V4L2 devices like radio may not
even have DMA. When it have, the DMA is done via ALSA, and not
via the V4L devnode.
In other words, MC is broken as a whole, but tagging it as BROKEN
right now would do more harm than good.
So, instead, let's mark, for now, the DVB part as broken and
block all new changes to MC while we fix this mess, whith
we hopefully will do for the next Kernel version.
Requested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull crypto fixes from Herbert Xu:
"This fixes the following issues:
- Crash in caam hash due to uninitialised buffer lengths.
- Alignment issue in caam RNG that may lead to non-random output"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: caam - fix RNG buffer cache alignment
crypto: caam - improve initalization for context state saves
|
|
This patch fixes a number of problems in crypto driver Kconfig
entries:
1. Select BLKCIPHER instead of BLKCIPHER2. The latter is internal
and should not be used outside of the crypto API itself.
2. Do not select ALGAPI unless you use a legacy type like
CRYPTO_ALG_TYPE_CIPHER.
3. Select the algorithm type that you are implementing, e.g., AEAD.
4. Do not select generic C code such as CBC/ECB unless you use them
as a fallback.
5. Remove default n since that is the default default.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The AEAD speed test SG list setup did not correctly mark the AD,
potentially causing a crash.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
This patch adds a speed test for rfc4309(ccm(aes)) as mode 212.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The patch
crypto: caam - Add definition of rd/wr_reg64 for little endian platform
added support for little endian platforms to the CAAM driver. Namely a
write and read function for 64 bit registers.
The only user of this functions is the Job Ring driver (drivers/crypto/caam/jr.c).
It uses the functions to set the DMA addresses for the input/output rings.
However, at least in the default configuration, the least significant 32 bits are
always in the base+0x0004 address; independent of the endianness of the bytes itself.
That means the addresses do not change with the system endianness.
DMA addresses are only 32 bits wide on non-64-bit systems, writing the upper 32 bits
of this value to the register for the least significant bits results in the DMA address
being set to 0.
Fix this by always writing the registers in the same way.
Suggested-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
It appears that, at some point last year, XFS made directory handling
changes which bring it into lockdep conflict with shmem_zero_setup():
it is surprising that mmap() can clone an inode while holding mmap_sem,
but that has been so for many years.
Since those few lockdep traces that I've seen all implicated selinux,
I'm hoping that we can use the __shmem_file_setup(,,,S_PRIVATE) which
v3.13's commit c7277090927a ("security: shmem: implement kernel private
shmem inodes") introduced to avoid LSM checks on kernel-internal inodes:
the mmap("/dev/zero") cloned inode is indeed a kernel-internal detail.
This also covers the !CONFIG_SHMEM use of ramfs to support /dev/zero
(and MAP_SHARED|MAP_ANONYMOUS). I thought there were also drivers
which cloned inode in mmap(), but if so, I cannot locate them now.
Reported-and-tested-by: Prarit Bhargava <prarit@redhat.com>
Reported-and-tested-by: Daniel Wagner <wagi@monom.org>
Reported-and-tested-by: Morten Stevens <mstevens@fedoraproject.org>
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix the checkpatch warning about CamelCase.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix the odd indention of vesa_mode_table.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
move vgamode table from the header file to the C file and mark it
as const.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
reduce code indention keeping the logic same.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix the alignment.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
fixes the checkpatch warning about using space after typecast.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
new line was missing in some of the dev_* macros while printing
the debug and error messages.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
numvgamodes was only used in one place, so remove the #define
and use its defined value.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The vesa_mode_table is not to be modified, so declare it as const.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add staging board support for the r8a7740-based armadillo800eva board
and add platform devices to allow in-tree continuous development of the
drivers on the armadillo800eva board.
When DT bindings are ready for theses drivers then the platform devices
in the armadillo800eva staging board code can easily be removed. Until
then we use platform devices to continuously improve the driver and
integrate code.
Added platform devices:
- sh_mobile_lcdc_fb for the on-board LCD.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add support for easy registering of one ore more platform devices that
may:
- need clocks that are described in DT,
- be part of a PM Domain.
All these dependencies are optional.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As of commit 9a1091ef0017c40a ("irqchip: gic: Support hierarchy irq
domain."), GIC IRQ numbers are virtual, breaking hardcoded hardware IRQ
numbers in platform device resources.
Translate the hardware IRQ numbers to virtual IRQ numbers to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As of commit 9a1091ef0017c40a ("irqchip: gic: Support hierarchy irq
domain."), GIC IRQ numbers are virtual, breaking hardcoded hardware IRQ
numbers in platform device resources.
Add support for translating hardware IRQ numbers to virtual IRQ numbers,
and fixing up platform device resources with hardcoded IRQ numbers.
Add a copyright header, including the original author.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently the staging board code is initialized from a late_initcall().
However, unused PM domains are also disabled from a late_initcall(),
which happens before due to link order.
Change the initialization of staging board code from using
late_initcall() to device_initcall() to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit d13778d537a0ed6115d2a79a942af999cfb8eec6.
Commit 13c11072536f2613 ("staging:board: remove unnecessary function")
fixed the build of drivers/staging/board/board.c.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch removes an open coded simple_open() function and replace file
operations references to the function with simple_open() instead
Signed-off-by: Abdul Hussain <habdul@visteon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch corrects line spacing by removing and adding newline
characters wherever necessary
Signed-off-by: Niranjan Dighe <ndighe@visteon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch replaces spaces by tabs at the start of the line and in
between variable declarations.
Signed-off-by: Niranjan Dighe <ndighe@visteon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch shall replaces user defined timer setup function with
standard timer setup macro. Also removes init_timer, because timer can
be initialized in setup_timer macro as well.
Signed-off-by: Gnanachandran Dhanapal <gdhanapa@visteon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Variable is always true; Resolve condition where it is used
(and change indentation of conditional expression).
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This queue is never used, and function handler is empty
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Delete several members of rtllib_device including
their initializers if needed.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Following members were removed:
- tmpJoinAction
- tmpSuppRateBuf
- bTmpIbpm
As a consequence several unused defines/enums/structs were
also removed from rtllib.h
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Variable was initialized and never used.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Current WIRELESS_EXT version is at least 22.
Resolve ifdefs and delete dead code.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This function/callback was initialized and never called.
rtl8192_get_nic_desc_num() function that was default
implementation was also removed.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This function was declared but never unused.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This function was declared but never unused.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This function was declared but never unused.
Also remove dequeue_mgmt() and rtllib_resume_tx() that are
no longer used.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This function was declared but never unused.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ENABLE_LOCK_DEBUG macro was never set, so condition that used
it can be resolved manually.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
