| Age | Commit message (Collapse) | Author |
|---|
|
Instead of using a custom glue layer connecting the wm8962 CODEC
to the SAI3 sound-dai, migrate the sound card to simple-audio-card.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The baseboard has an WM8962 Audio CODEC connected to the SAI3
peripheral. The CODEC supports stereo in and out
and a microphone input connected to the headphone jack.
Route this CODEC through the simple-audio-card driver.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
As documented in pfuze100.yaml, the correct name for the regulator is
"coin", so change it to fix the following DT check warning:
imx6ul-ccimx6ulsbcexpress.dtb: pmic@8: regulators: 'vcoin' does not match any of the regexes:
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Devicetree node names should be generic. Use 'pmic' as node name
to avoid devicetree check warning from pfuze100.yaml.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
According to Documentation/devicetree/bindings/sound/imx-audmux.yaml,
there must be a "mux-" prefix in the audmux port nodes.
Add the "mux-" prefix to avoid devicetree schema warnings.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Describe the SD1_VSELECT pad, which is necessary to allow UHS modes.
Also, to support higher SD card speed modes, describe the 100MHz and
200MHz SD card pinctrl entries.
Suggested-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Improve the devicetree description by adding the SD card regulator
that is controlled via GPIO5_2.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Correct the following warnings by adding the required supplies (AVDD, DVDD)
for the ov5640 node.
arch/arm/boot/dts/stm32mp157c-ev1.dtb: camera@3c: 'AVDD-supply' is a required property
From schema: Documentation/devicetree/bindings/media/i2c/ovti,ov5640.yaml
arch/arm/boot/dts/stm32mp157c-ev1.dtb: camera@3c: 'DVDD-supply' is a required property
From schema: Documentation/devicetree/bindings/media/i2c/ovti,ov5640.yaml
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
The generic ADC channel binding is recommended over legacy one, update the
DT to the modern binding. No functional change. For further details, see
commit which adds the generic binding to STM32 ADC binding document:
'664b9879f56e ("dt-bindings: iio: stm32-adc: add generic channel binding")'
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Use STM32 ADC generic bindings instead of legacy bindings on
DHCOR Testbench board.
The STM32 ADC specific binding to declare channels has been deprecated,
hence adopt the generic IIO channels bindings, instead.
The STM32MP151 device tree now exposes internal channels using the
generic binding. This makes the change mandatory here to avoid a mixed
use of legacy and generic binding, which is not supported by the driver.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Use STM32 ADC generic bindings instead of legacy bindings on
DHCOR DRC Compact board.
The STM32 ADC specific binding to declare channels has been deprecated,
hence adopt the generic IIO channels bindings, instead.
The STM32MP151 device tree now exposes internal channels using the
generic binding. This makes the change mandatory here to avoid a mixed
use of legacy and generic binding, which is not supported by the driver.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Use STM32 ADC generic bindings instead of legacy bindings on
emtrion GmbH Argon boards.
The STM32 ADC specific binding to declare channels has been deprecated,
hence adopt the generic IIO channels bindings, instead.
The STM32MP151 device tree now exposes internal channels using the
generic binding. This makes the change mandatory here to avoid a mixed
use of legacy and generic binding, which is not supported by the driver.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Use STM32 ADC generic bindings instead of legacy bindings on
STM32MP157c-ed1 board.
The STM32 ADC specific binding to declare channels has been deprecated,
hence adopt the generic IIO channels bindings, instead.
The STM32MP151 device tree now exposes internal channels using the
generic binding. This makes the change mandatory here to avoid a mixed
use of legacy and generic binding, which is not supported by the driver.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
U-Boot enables ADC1&2 to support USB power measurement and ADC
calibration on STM32MP15x Disco boards.
When leaving U-boot the ADCs do not return to power down state
to keep ADC linear calibration available for kernel.
Enable ADC1&2 by default on STM32MP15xx-DKx boards to align kernel
DT with Uboot. This avoids to shutdown the ADCs VDDA, while the
ADCs are not in power down.
Use STM32 ADC generic bindings instead of legacy bindings on
STM32MP15xx-DKx boards.
The ADC pins on Arduino connector are not set by default.
These pins are added in A7 Disco example DTs only.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Set STM32 ADC2 as a consumer of BSEC on STM32MP15, to retrieve
vrefint calibration data saved in OTP.
During the calibration process vrefp is set to 3.3V and the data
acquired is saved to the OTP. This data is used by the ADC driver
to calculated the actual value of vrefp according to the formula:
vrefp = 3.3 x vrefint_cal / vrefint_data
The vrefint channel provides the actual value of vrefp,
which can be used to correct ADC acquisition data.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Describe vrefint calibration cell to be retrieved through bsec.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Add STM32 ADC2 internal channels VREFINT and VDDCORE to STM32MP15x SoCs.
VBAT internal channel is not defined by default in SoC DT, and
has be defined in board DT when needed, instead. This avoids unwanted
current consumption on battery, when ADC conversions are performed
on any other channels.
The internal channels are defined in STM32MP15 SoC DT according to the
generic IIO channel bindings. The STM32 driver does not support a mixed
use of legacy and generic channels. When generic channels are defined,
legacy channels are ignored. This involves that the board device trees
using legacy bindings for ADC2, have to be reworked.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Exposed on CN4. Tested by connecting it to a Renesas Ebisu board.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230525084823.4195-3-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
The schematics are misleading, the flow control is for HSCIF1. We need
SCIF1 for GNSS/GPS which does not use flow control.
Fixes: c6c816e22bc8 ("arm64: dts: ulcb-kf: enable SCIF1")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230525084823.4195-2-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
make dtbs_check:
arch/arm/boot/dts/renesas/r8a7743-iwg20d-q7.dtb: backlight: pwms: [[58, 0, 5000000], [0]] is too long
From schema: Documentation/devicetree/bindings/leds/backlight/pwm-backlight.yaml
arch/arm/boot/dts/renesas/r8a7743-iwg20d-q7-dbcm-ca.dtb: backlight: pwms: [[67, 0, 5000000], [0]] is too long
From schema: Documentation/devicetree/bindings/leds/backlight/pwm-backlight.yaml
arch/arm/boot/dts/renesas/r8a7744-iwg20d-q7-dbcm-ca.dtb: backlight: pwms: [[67, 0, 5000000], [0]] is too long
From schema: Documentation/devicetree/bindings/leds/backlight/pwm-backlight.yaml
arch/arm/boot/dts/renesas/r8a7744-iwg20d-q7.dtb: backlight: pwms: [[58, 0, 5000000], [0]] is too long
From schema: Documentation/devicetree/bindings/leds/backlight/pwm-backlight.yaml
PWM specifiers referring to R-Car PWM Timer Controllers should contain
only two cells.
Fix this by dropping the bogus third cell.
Fixes: 6f89dd9e9325d05b ("ARM: dts: iwg20d-q7-common: Add LCD support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/6e5c3167424a43faf8c1fa68d9667b3d87dc86d8.1684855911.git.geert+renesas@glider.be
|
|
Add iommu-map and iommu-map-mask properties to the PCIe host nodes.
Note that iommu-map-mask should be zero because the IPMMU assigns
one micro TLB ID only, to the PCIe host.
Also change the dma-ranges arguments for IOMMU. Note that dma-ranges
can be used if the IOMMU is disabled.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230510090358.261266-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
As all level 2 and level 3 caches are unified, add required
cache-unified property to fix warnings like:
tegra210-p2371-0000.dtb: l2-cache: 'cache-unified' is a required property
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
This adds a DT node to hook up the internal temperature ADC to the
iio-hwmon driver. The various voltage + current ADCs are consumed and
exposed by their respective drivers, but this is not and is always
available. Naming chosen to match the axp20x_ prefix the power sensors
use.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/2a9bd53a65c4a154cccba622c60cbffcdceaeb95.1683719613.git.noodles@earth.li
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
|
|
These alternate pins for mmc2 are brought out to the 40 pin U14 header
on the C.H.I.P and can be used to add an external MMC device with a 4
bit interface. See
https://byteporter.com/ntc-chip-micro-sd-slot/
for further details on how.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/7949169f581cab37175602188f44bc26e79a45c0.1683719613.git.noodles@earth.li
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
|
|
The C.H.I.P has an rtl8723bs device with the bluetooth interface hooked
up on UART3. Support for this didn't exist in mainline when the DTS was
initially added, but it does now, so enable it.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/49ff7f3cc79838a55a89baae09a4ba12c88573fb.1683719613.git.noodles@earth.li
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
|
|
On Meson8 uart_B and uart_C do not work, because they are relying on
incorrect clocks. Change the references of pclk to the correct CLKID
(UART1 for uart_B and UART2 for uart_C), to allow use of the two uarts.
This was originally reported by Hans-Frieder Vogt for Meson8b [0], but
the same bug is also present in meson8.dtsi
[0] https://lore.kernel.org/linux-amlogic/trinity-bf20bcb9-790b-4ab9-99e3-0831ef8257f4-1680878185420@3c-app-gmx-bap55/
Fixes: 57007bfb5469 ("ARM: dts: meson8: Fix the UART device-tree schema validation")
Reported-by: Hans-Frieder Vogt <hfdevel@gmx.net> # for meson8b.dtsi
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20230516203029.1031174-1-martin.blumenstingl@googlemail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
|
|
Add the devices working with current drivers for the
Epson Moverio BT-200 AR glasses consisting of a control unit
and the glasses itself.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Message-Id: <20230313110409.2294154-1-andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The NAND wait pin is connected to the GPMC, but this is not mentioned
in the DT bindings. Let's fix this.
Signed-off-by: Alexander Shiyan <eagle.alexander923@gmail.com>
Message-Id: <20230524091157.775960-1-eagle.alexander923@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Introduce support for the Lenovo Flex 5G laptop, built on the Qualcomm
SC8180X platform. Supported peripherals includes keyboard, touchpad,
UFS storage, external USB and WiFi.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230530162454.51708-16-vkoul@kernel.org
|
|
Introduce support for the SC8180X reference device, aka Primus, with
debug UART, regulators, UFS and USB support.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230530162454.51708-15-vkoul@kernel.org
|
|
SC8180X based platforms have PM8150, PM8150C, PMC8180 and SMB2351 PMICs,
so add these as well
Co-developed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230530162454.51708-14-vkoul@kernel.org
|
|
This patch adds gpu, gmu, gpucc, dispcc and finally the mdss node with
dsi0/1, dp0/1 and edp subnodes as found in this SoC
Co-developed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230530162454.51708-13-vkoul@kernel.org
|
|
This patch adds remoteprocs, wifi and usb and usb phy nodes
for this SoC
Co-developed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230530162454.51708-12-vkoul@kernel.org
|
|
This patch adds PCIe instances found on this SoC
Co-developed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230530162454.51708-11-vkoul@kernel.org
|
|
This patch adds qup instances and i2c, spi, serial ports
Co-developed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230530162454.51708-10-vkoul@kernel.org
|
|
This patch adds tsens nodes and thermal zones for sc8180x SoC
Co-developed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230530162454.51708-9-vkoul@kernel.org
|
|
This add interconnect nodes and add LMH to sc8180x SoC dtsi
Co-developed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230530162454.51708-8-vkoul@kernel.org
|
|
Introduce a base dtsi for the Qualcomm SC8180x platform, with CPUs,
global clock controller, SMMU, rpmh clocks, rpmh power-domains,
CPUfreq etc
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230530162454.51708-7-vkoul@kernel.org
|
|
Enable MDSS, GPU and DSI panel output on the APQ8074 dragonboard.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230507190735.2333145-5-dmitry.baryshkov@linaro.org
|
|
Enable ADSP and Modem DSPs on APQ8074 dragonboard. The MSS region
differs from the one defined in the msm8974, so it overriden locally.
The modem is specified use mba.mbn instead of mbn.b00 (for the sake of
similarity with other platforms). This requires a patch for remoteproc
to be applied [1].
[1] https://lore.kernel.org/all/20230507172041.2320279-1-dmitry.baryshkov@linaro.org/
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230507190735.2333145-4-dmitry.baryshkov@linaro.org
|
|
Add the qcom,controlled-remotely property for the blsp2_bam
controller node. This board requires this, otherwise the board stalls
during the boot for some reason (most probably because TZ mishandles the
protection error and keeps on looping somewhere inside).
Fixes: 62bc81792223 dts: msm8974: Add blsp2_bam dma node
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230507190735.2333145-3-dmitry.baryshkov@linaro.org
|
|
The watch has a DRV2605 for haptics. Add a node for it based on the
values found in the downstream board file.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230430-drv260x-improvements-v1-5-1fb28b4cc698@z3ntu.xyz
|
|
This enables userspace to signal the bootloader to go into the
bootloader or recovery mode.
The magic values can be found in both the downstream kernel and the LK
kernel (bootloader).
Signed-off-by: Matti Lehtimäki <matti.lehtimaki@gmail.com>
Reviewed-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230520121933.15533-5-matti.lehtimaki@gmail.com
|
|
Add device node for the rpm-stats pseudo device.
Signed-off-by: Matti Lehtimäki <matti.lehtimaki@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230520121933.15533-4-matti.lehtimaki@gmail.com
|
|
Enable perf events on MSM8226 devices by adding the PMU node.
Signed-off-by: Matti Lehtimäki <matti.lehtimaki@gmail.com>
Reviewed-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230520121933.15533-3-matti.lehtimaki@gmail.com
|
|
Enable PCIe Endpoint controller on the SDX65 MTP board based
on Qualcomm SDX65 platform.
Signed-off-by: Rohit Agarwal <quic_rohiagar@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/1684432073-28490-6-git-send-email-quic_rohiagar@quicinc.com
|
|
Enable PCIe PHY on SDX65 MTP for PCIe EP.
Signed-off-by: Rohit Agarwal <quic_rohiagar@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/1684432073-28490-5-git-send-email-quic_rohiagar@quicinc.com
|
|
Add support for PCIe Endpoint controller on the
Qualcomm SDX65 platform.
Signed-off-by: Rohit Agarwal <quic_rohiagar@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/1684432073-28490-4-git-send-email-quic_rohiagar@quicinc.com
|
|
Add devicetree support for PCIe PHY used in SDX65 platform. This PHY is
used by the PCIe EP controller.
Signed-off-by: Rohit Agarwal <quic_rohiagar@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/1684432073-28490-3-git-send-email-quic_rohiagar@quicinc.com
|
|
Bindings expect WCNSS Bluetooth child to be named "bluetooth":
remoteproc@fb204000: smd-edge:wcnss: 'bt' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230421195437.31513-1-krzysztof.kozlowski@linaro.org
|
