| Age | Commit message (Collapse) | Author |
|---|
|
Describe SYS-DMAC0/1 in the R8A7792 device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The initial R8A7792 SoC device tree including CPU cores, GIC, timer, SYSC,
and the required clock descriptions.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add macros usable by the device tree sources to reference R8A7792 SYSC power
domains by index.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add macros usable by the device tree sources to reference the R8A7792
clocks by index.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
With the SION bit set a pin can be read as GPIO even though it's not muxed
as GPIO. This is useful at times. The downside however is that the signal
is not only routed to the GPIO IP but also all other IPs that can make use
of the pin. This resulted in more than one issue for me in the past. Things
like spi transfers that result in usb reenumeration or setting a GPIO to a
value that triggers an RTS irq for an UART.
This convinces me that the SION bit does more harm than good and so all
SION bits are removed that are not known to be needed.
Note that this has no influence on GPIOs under Linux as the gpio-mxc
driver just reports the level the pin is driven to for outputs and not
the level as seen on the pin.
If this commit introduces a regression for you, please report which SION
bit is essential for your setup.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Update DTSI file to add the reset controller node.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
On these two boards, the serial0 is used for inter-chip connection,
so cannot be used for login console. The serial2 is used instead
for them, but it is tedious to use because upper level deployment
projects must switch login console per board.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This node consists of various system-level configuration registers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This pin-muxing is needed to get access to the UniPhier System Bus.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into next/dt
DT Changes for 4.8:
- New board: Olimex SAM9-L9260
- Fix crystal definitions for Denx ma5d4
- Remove leftover clock definitions
- Add stdout-path for usb_a9260/a9g20
* tag 'at91-ab-4.8-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: dts: at91: calao: remove leftovers clock definition
ARM: dts: at91: pm9g45: remove leftovers clock definition
ARM: dts: at91: mpa1600: remove leftovers clock definition
ARM: dts: at91: ge863-pro3: remove leftovers clock definition
ARM: dts: at91: at91-foxg20: remove leftovers clock definition
ARM: dts: at91: at91-cosino: remove leftovers clock definition
ARM: dts: at91: at91-ariag25: remove leftovers clock definition
ARM: dts: at91: animeo_ip: remove leftovers clock definition
ARM: dts: at91: ma5d4: properly define crystals frequencies
ARM: dts: at91: usb_a9g20: use stdout-path
ARM: dts: at91: Add DT support for Olimex SAM9-L9260 board.
ARM: dts: at91: at91sam9260: Remove leading zeros in OHCI node.
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Name the Pin Function Controller subnode for SCIFA4 after its device
name, instead of after the serial port alias.
This avoids conflicts when adding support for more serial ports later,
either here or in a DT overlay.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Name the Pin Function Controller subnode for QSPI after its device name,
instead of after the spi interface alias.
This avoids conflicts when enabling support for more spi interfaces
later, either here or in a DT overlay.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Name the Pin Function Controller subnode for SCIF2 after its device
name, instead of using some arbitrary name that looks like a serial port
alias, but differs from the actual alias.
This avoids conflicts when enabling support for more serial ports later,
either here or in a DT overlay.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Name the Pin Function Controller subnode for QSPI after its device name,
instead of after the spi interface alias.
This avoids conflicts when enabling support for more spi interfaces later,
either here or in a DT overlay.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Name the Pin Function Controller subnode for SCIF2 after its device
name, instead of using some arbitrary name that looks like a serial port
alias, but differs from the actual alias.
This avoids conflicts when enabling support for more serial ports later,
either here or in a DT overlay.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Name the Pin Function Controller subnode for QSPI after its device name,
instead of after the spi interface alias.
This avoids conflicts when enabling support for more spi interfaces later,
either here or in a DT overlay.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Name the Pin Function Controller subnodes for SCIF0 and SCIF1 after
their device names, instead of after the serial port aliases.
This avoids conflicts when enabling support for more serial ports later,
either here or in a DT overlay.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Name the Pin Function Controller subnode for QSPI after its device name,
instead of after the spi interface alias.
This avoids conflicts when enabling support for more spi interfaces
later, either here or in a DT overlay.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Name the Pin Function Controller subnode for SCIF0 after its device
name, instead of after the serial port alias.
This avoids conflicts when enabling support for more serial ports later,
either here or in a DT overlay.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Name the Pin Function Controller subnodes for QSPI and MSIOF0 after
their device names, instead of after the spi interface aliases.
This avoids conflicts when enabling support for more spi interfaces
later, either here or in a DT overlay.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Name the Pin Function Controller subnodes for SCIF0 and SCIF1 after
their device names, instead of after the serial port aliases.
This avoids conflicts when enabling support for more serial ports later,
either here or in a DT overlay.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Name the Pin Function Controller subnode for VIN1 after its device name,
instead of using the generic and indexless "vin".
This avoids conflicts when enabling support for more video inputs later,
either here or in a DT overlay.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Name the Pin Function Controller subnodes for QSPI and MSIOF1 after
their device names, instead of after the spi interface aliases.
This avoids conflicts when enabling support for more spi interfaces
later, either here or in a DT overlay.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Name the Pin Function Controller subnodes for SCIF0 and SCIFA1 after
their device names, instead of after the serial port aliases.
This avoids conflicts when enabling support for more serial ports later,
either here or in a DT overlay.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Name the Pin Function Controller subnodes for SCIF2 and SCIF4 after
their device names, instead of using some arbitrary names that look like
serial port aliases, but differ from the actual aliases.
This avoids conflicts when enabling support for more serial ports later,
either here or in a DT overlay.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Name the Pin Function Controller subnode for SCIF0 after its device
name, instead of after the serial port alias.
This avoids conflicts when enabling support for more serial ports later,
either here or in a DT overlay.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Name the Pin Function Controller subnode for SCIFA1 after its device
name, instead of after the serial port alias.
This avoids conflicts when enabling support for more serial ports later,
either here or in a DT overlay.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Name the Pin Function Controller subnode for MMC0 after its device name,
instead of using the generic and indexless "mmc".
This avoids conflicts when enabling support for more MMC interfaces
later, either here or in a DT overlay.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Name the Pin Function Controller subnode for SCIFA0 after its device
name, instead of after the serial port alias.
This avoids conflicts when enabling support for more serial ports later,
either here or in a DT overlay.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into next/dt
SoCFPGA DTS updates for v4.8
- Update Arria10 ECC manager
- Add ethernet alias for Arria10
- Update serial alias for Arria10
* tag 'socfpga_updates_v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: dts: socfpga: fix definitions of serial console
ARM: dts: socfpga: add ethernet alias on Arria10
ARM: dts: Move Arria10 SDRAM as child of ECC Manager
ARM: dts: Arria10 ECC Manager IRQ controller changes
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/dt
Ux500 devicetree patches:
- Move the ab8500 compatible string from the board to the
chipset.
- Define GPIO line names for the boards.
* tag 'ux500-dt-asoc-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: dts: UX500: name the GPIO lines on HREFv60plus
ARM: dts: Ux500: name the GPIO lines on Snowball
ARM: dts: Ux500: move compatible string to chipset
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Renesas ARM Based SoC DT Updates for v4.8
* Fix W=1 dtc warnings
* Reverence both DMA controllers on R-Car Gen 2 SoCs
* Remove nonexistent thermal sensor clock from r8a7794 SoC
* Correct unit names for cpu nodes on r8a7790 SoC
* Add MMCIF0 to r8a7793 SoC
* RTS/CTS hardware flow control for kzm9g and bockw boards
* tag 'renesas-dt-for-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (30 commits)
ARM: dts: silk: Fix W=1 dtc warnings
ARM: dts: porter: Fix W=1 dtc warnings
ARM: dts: marzen: Fix W=1 dtc warnings
ARM: dts: lager: Fix W=1 dtc warnings
ARM: dts: kzm9g: Fix W=1 dtc warnings
ARM: dts: kzm9d: Fix W=1 dtc warnings
ARM: dts: koelsch: Fix W=1 dtc warnings
ARM: dts: gose: Fix W=1 dtc warnings
ARM: dts: genmai: Fix W=1 dtc warnings
ARM: dts: bockw: Fix W=1 dtc warnings
ARM: dts: armadillo800eva: Fix W=1 dtc warnings
ARM: dts: ape6evm: Fix W=1 dtc warnings
ARM: dts: sh73a0: Fix W=1 dtc warnings
ARM: dts: r8a7794: Fix W=1 dtc warnings
ARM: dts: r8a7793: Fix W=1 dtc warnings
ARM: dts: r8a7791: Fix W=1 dtc warnings
ARM: dts: r8a7790: Fix W=1 dtc warnings
ARM: dts: r8a7778: Fix W=1 dtc warnings
ARM: dts: r8a7740: Fix W=1 dtc warnings
ARM: dts: r8a73a4: Fix W=1 dtc warnings
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Topic branch for adding Exynos 5410 Odroid XU board for v4.8.
This brings support for Hardkernel's Odroid XU board. It was the first
design with big.LITTLE SoC from Samsung: Exynos5410. The board is not
very popular. Newer XU3 and XU4 got more attention.
Board details:
1. Exynos5410 octa-core (A15+A7, however as of now only one cluster is
enabled),
2. 2 GB DDR3 RAM,
3. PowerVR SGX544MP3 GPU (not enabled in DTS),
4. USB 3.0 Host x 1, USB 3.0 OTG x 1, USB 2.0 Host x 4,
5. HDMI 1.4a, MIPI DSI and Display Port (Display Port not on all of
revisions though),
6. eMMC 4.5 and microSD slots.
* tag 'samsung-dt-odroid-xu-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: (28 commits)
ARM: dts: exynos: Add watchdog and Security SubSystem to Exynos5410
ARM: dts: exynos: Configure PWM, usb3503, PMIC and thermal on Odroid XU board
ARM: dts: exynos: Add Thermal Management Unit to Exynos5410
ARM: dts: exynos: Interrupt for USB DWC3-1 differs between Exynos5420 and 5410
dt-bindings: clock: Add watchdog and SSS clock IDs to Exynos5410
dt-bindings: clock: Add TMU clock ID to Exynos5410
ARM: dts: exynos: Add RTC and I2C to Exynos5410
ARM: dts: exynos: Add I2C, PWM and UART pinctrl to Exynos5410
ARM: dts: exynos: Move HSI2C nodes to exynos54xx.dtsi
ARM: dts: exynos: Add initial support for Odroid XU board
ARM: dts: exynos: Add USB to Exynos5410
ARM: dts: exynos: Move common Exynos5410/542x/5800 nodes to new DTSI
ARM: dts: exynos: MCT is not an interrupt controller and extend length of iomap
ARM: dts: exynos: Enable UART3 on Exynos5410
ARM: dts: exynos: Include common exynos5 in exynos5410.dtsi
ARM: dts: exynos: Move Exynos5250 and Exynos5420 nodes under soc
ARM: dts: exynos: Use phandle to get parent node in exynos5250-snow
ARM: dts: exynos: Prepare for inclusion of exynos5.dtsi in exynos5410.dtsi
ARM: dts: exynos: Move common nodes to exynos5.dtsi
ARM: dts: exynos: Split Odroid XU3 LEDs to separate DTSI
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Samsung DeviceTree update for v4.8:
1. Add missing async bridge for MFC power domain on Exynos5420.
This fixes imprecise abort on s5p-mfc re-bind.
2. Define regulator supplies for MMC nodes on Exynos4412 Odroid boards
and for TMU on Exynos542x Peach boards.
3. Thermal cleanups on Odroid XU3-family (Exynos5422).
4. Enable AX88760 USB hub on Origen board (Exynos4412).
5. Minor cleanups.
* tag 'samsung-dt-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: No need to enable TMU nodes on Odroid XU3 family
ARM: dts: exynos: Add TMU nodes regulator supply for Peach boards
ARM: dts: exynos: Use new compatible string for thermistors in Trats2
ARM: dts: exynos: Remove unneded always-on for regulators on Peach boards
ARM: dts: exynos: Enable AX88760 USB hub on Origen board
ARM: dts: exynos: Only Odroid XU3-family boards use DTSI with CPU thermal nodes
ARM: dts: exynos: Lower SD card interface voltage to 2.8 V on Odroid X/X2/U3
ARM: dts: exynos: Define vqmmc for eMMC card on Odroid X/X2/U3
ARM: dts: exynos: Define vqmmc for SD card and allow disabling regulators on Odroid X/X2/U3
ARM: dts: exynos: Add async-bridge clock to MFC power domain for Exynos5420
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Define the port mapping for the SmartRG SR400ACE device.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Add interrupt mapping for the Switch Register Access Block. Only 12
interrupts are usable at the moment even though up to 32 are dedicated
to the SRAB.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Add the Switch Register Access Block which is a special piece of
hardware allowing us to perform indirect read/writes towards the
integrated BCM5301X Ethernet switch.
We also add the 4 Gigabit MAC Device Tree nodes within the brcm,bus-axi
bus node to get proper binding between the BCMA instantiated core and
the Device Tree nodes. We will need that to be able to reference
Ethernet Device Tree nodes in a future patch adding the switch ports
layout.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal management fixes from Zhang Rui:
- fix an ordering issue in cpu cooling that cooling device is
registered before it's ready (freq_table being populated).
(Lukasz Luba)
- fix a missing comment update (Caesar Wang)
* 'for-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal: add the note for set_trip_temp
thermal: cpu_cooling: fix improper order during initialization
|
|
This binding describes the control interface for the Qualcomm WCNSS.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
This patch adds the firmware node for the APQ8064
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
This patch adds the Qualcomm SCM firmware node.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
This patch adds the firmware node for the SCM
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
This patch adds the device tree support for the Qualcomm SCM firmware.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
|
|
This patch adds the power key device tree node.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The #size-cells for the pmics are 0, but we specify a size in the
reg property so that MPP and GPIO modules can figure out how many
pins there are. Now that we've done that by counting irqs, we can
remove the size elements in the reg properties and be DT
compliant.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Enable the sdcard slot and wire up the regulators for the two
storage controllers found on the apq8074 dragonboard.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Add the appropriate min/max voltages for the regulators on the
apq8074 dragonboard so that they can be used by clients properly.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Pull block layer fixes from Jens Axboe:
"A small collection of fixes for the current series. This contains:
- Two fixes for xen-blkfront, from Bob Liu.
- A bug fix for NVMe, releasing only the specific resources we
requested.
- Fix for a debugfs flags entry for nbd, from Josef.
- Plug fix from Omar, fixing up a case of code being switched between
two functions.
- A missing bio_put() for the new discard callers of
submit_bio_wait(), fixing a regression causing a leak of the bio.
From Shaun.
- Improve dirty limit calculation precision in the writeback code,
fixing a case where setting a limit lower than 1% of memory would
end up being zero. From Tejun"
* 'for-linus' of git://git.kernel.dk/linux-block:
NVMe: Only release requested regions
xen-blkfront: fix resume issues after a migration
xen-blkfront: don't call talk_to_blkback when already connected to blkback
nbd: pass the nbd pointer for flags debugfs
block: missing bio_put following submit_bio_wait
blk-mq: really fix plug list flushing for nomerge queues
writeback: use higher precision calculation in domain_dirty_limits()
|
