| Age | Commit message (Collapse) | Author |
|---|
|
the struct member `phy_node` of struct axienet_local is not used by the
driver anymore after initialization. It might be a remnent of old code
and could be removed.
Signed-off-by: Andy Chiu <andy.chiu@sifive.com>
Reviewed-by: Greentime Hu <greentime.hu@sifive.com>
Reviewed-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The call to axienet_mdio_setup should not depend on whether "phy-node"
pressents on the DT. Besides, since `lp->phy_node` is used if PHY is in
SGMII or 100Base-X modes, move it into the if statement. And the next patch
will remove `lp->phy_node` from driver's private structure and do an
of_node_put on it right away after use since it is not used elsewhere.
Signed-off-by: Andy Chiu <andy.chiu@sifive.com>
Reviewed-by: Greentime Hu <greentime.hu@sifive.com>
Reviewed-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In some cases, xdp tx_queue can get used before initialization.
1. interface up/down
2. ring buffer size change
When CPU cores are lower than maximum number of channels of sfc driver,
it creates new channels only for XDP.
When an interface is up or ring buffer size is changed, all channels
are initialized.
But xdp channels are always initialized later.
So, the below scenario is possible.
Packets are received to rx queue of normal channels and it is acted
XDP_TX and tx_queue of xdp channels get used.
But these tx_queues are not initialized yet.
If so, TX DMA or queue error occurs.
In order to avoid this problem.
1. initializes xdp tx_queues earlier than other rx_queue in
efx_start_channels().
2. checks whether tx_queue is initialized or not in efx_xdp_tx_buffers().
Splat looks like:
sfc 0000:08:00.1 enp8s0f1np1: TX queue 10 spurious TX completion id 250
sfc 0000:08:00.1 enp8s0f1np1: resetting (RECOVER_OR_ALL)
sfc 0000:08:00.1 enp8s0f1np1: MC command 0x80 inlen 100 failed rc=-22
(raw=22) arg=789
sfc 0000:08:00.1 enp8s0f1np1: has been disabled
Fixes: f28100cb9c96 ("sfc: fix lack of XDP TX queues - error XDP TX failed (-22)")
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current code can lead to the following race:
CPU0 CPU1
rxrpc_exit_net()
rxrpc_peer_keepalive_worker()
if (rxnet->live)
rxnet->live = false;
del_timer_sync(&rxnet->peer_keepalive_timer);
timer_reduce(&rxnet->peer_keepalive_timer, jiffies + delay);
cancel_work_sync(&rxnet->peer_keepalive_work);
rxrpc_exit_net() exits while peer_keepalive_timer is still armed,
leading to use-after-free.
syzbot report was:
ODEBUG: free active (active state 0) object type: timer_list hint: rxrpc_peer_keepalive_timeout+0x0/0xb0
WARNING: CPU: 0 PID: 3660 at lib/debugobjects.c:505 debug_print_object+0x16e/0x250 lib/debugobjects.c:505
Modules linked in:
CPU: 0 PID: 3660 Comm: kworker/u4:6 Not tainted 5.17.0-syzkaller-13993-g88e6c0207623 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: netns cleanup_net
RIP: 0010:debug_print_object+0x16e/0x250 lib/debugobjects.c:505
Code: ff df 48 89 fa 48 c1 ea 03 80 3c 02 00 0f 85 af 00 00 00 48 8b 14 dd 00 1c 26 8a 4c 89 ee 48 c7 c7 00 10 26 8a e8 b1 e7 28 05 <0f> 0b 83 05 15 eb c5 09 01 48 83 c4 18 5b 5d 41 5c 41 5d 41 5e c3
RSP: 0018:ffffc9000353fb00 EFLAGS: 00010082
RAX: 0000000000000000 RBX: 0000000000000003 RCX: 0000000000000000
RDX: ffff888029196140 RSI: ffffffff815efad8 RDI: fffff520006a7f52
RBP: 0000000000000001 R08: 0000000000000000 R09: 0000000000000000
R10: ffffffff815ea4ae R11: 0000000000000000 R12: ffffffff89ce23e0
R13: ffffffff8a2614e0 R14: ffffffff816628c0 R15: dffffc0000000000
FS: 0000000000000000(0000) GS:ffff8880b9c00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fe1f2908924 CR3: 0000000043720000 CR4: 00000000003506f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
__debug_check_no_obj_freed lib/debugobjects.c:992 [inline]
debug_check_no_obj_freed+0x301/0x420 lib/debugobjects.c:1023
kfree+0xd6/0x310 mm/slab.c:3809
ops_free_list.part.0+0x119/0x370 net/core/net_namespace.c:176
ops_free_list net/core/net_namespace.c:174 [inline]
cleanup_net+0x591/0xb00 net/core/net_namespace.c:598
process_one_work+0x996/0x1610 kernel/workqueue.c:2289
worker_thread+0x665/0x1080 kernel/workqueue.c:2436
kthread+0x2e9/0x3a0 kernel/kthread.c:376
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:298
</TASK>
Fixes: ace45bec6d77 ("rxrpc: Fix firewall route keepalive")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Marc Dionne <marc.dionne@auristor.com>
Cc: linux-afs@lists.infradead.org
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While parsing user-provided actions, openvswitch module may dynamically
allocate memory and store pointers in the internal copy of the actions.
So this memory has to be freed while destroying the actions.
Currently there are only two such actions: ct() and set(). However,
there are many actions that can hold nested lists of actions and
ovs_nla_free_flow_actions() just jumps over them leaking the memory.
For example, removal of the flow with the following actions will lead
to a leak of the memory allocated by nf_ct_tmpl_alloc():
actions:clone(ct(commit),0)
Non-freed set() action may also leak the 'dst' structure for the
tunnel info including device references.
Under certain conditions with a high rate of flow rotation that may
cause significant memory leak problem (2MB per second in reporter's
case). The problem is also hard to mitigate, because the user doesn't
have direct control over the datapath flows generated by OVS.
Fix that by iterating over all the nested actions and freeing
everything that needs to be freed recursively.
New build time assertion should protect us from this problem if new
actions will be added in the future.
Unfortunately, openvswitch module doesn't use NLA_F_NESTED, so all
attributes has to be explicitly checked. sample() and clone() actions
are mixing extra attributes into the user-provided action list. That
prevents some code generalization too.
Fixes: 34ae932a4036 ("openvswitch: Make tunnel set action attach a metadata dst")
Link: https://mail.openvswitch.org/pipermail/ovs-dev/2022-March/392922.html
Reported-by: Stéphane Graber <stgraber@ubuntu.com>
Signed-off-by: Ilya Maximets <i.maximets@ovn.org>
Acked-by: Aaron Conole <aconole@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tlb_remove_huge_tlb_entry only considers PMD_SIZE and PUD_SIZE when
updating the mmu_gather structure.
Unfortunately on arm64 there are two additional huge page sizes that
need to be covered: CONT_PTE_SIZE and CONT_PMD_SIZE. Where an end-user
attempts to employ contiguous huge pages, a VM_BUG_ON can be experienced
due to the fact that the tlb structure hasn't been correctly updated by
the relevant tlb_flush_p.._range() call from tlb_remove_huge_tlb_entry.
This patch adds inequality logic to the generic implementation of
tlb_remove_huge_tlb_entry s.t. CONT_PTE_SIZE and CONT_PMD_SIZE are
effectively covered on arm64. Also, as well as ptes, pmds and puds;
p4ds are now considered too.
Reported-by: David Hildenbrand <david@redhat.com>
Suggested-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/linux-mm/811c5c8e-b3a2-85d2-049c-717f17c3a03a@redhat.com/
Signed-off-by: Steve Capper <steve.capper@arm.com>
Acked-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20220330112543.863-1-steve.capper@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
The alternatives code must be `noinstr` such that it does not patch itself,
as the cache invalidation is only performed after all the alternatives have
been applied.
Mark patch_alternative() as `noinstr`. Mark branch_insn_requires_update()
and get_alt_insn() with `__always_inline` since they are both only called
through patch_alternative().
Booting a kernel in QEMU TCG with KCSAN=y and ARM64_USE_LSE_ATOMICS=y caused
a boot hang:
[ 0.241121] CPU: All CPU(s) started at EL2
The alternatives code was patching the atomics in __tsan_read4() from LL/SC
atomics to LSE atomics.
The following fragment is using LL/SC atomics in the .text section:
| <__tsan_unaligned_read4+304>: ldxr x6, [x2]
| <__tsan_unaligned_read4+308>: add x6, x6, x5
| <__tsan_unaligned_read4+312>: stxr w7, x6, [x2]
| <__tsan_unaligned_read4+316>: cbnz w7, <__tsan_unaligned_read4+304>
This LL/SC atomic sequence was to be replaced with LSE atomics. However since
the alternatives code was instrumentable, __tsan_read4() was being called after
only the first instruction was replaced, which led to the following code in memory:
| <__tsan_unaligned_read4+304>: ldadd x5, x6, [x2]
| <__tsan_unaligned_read4+308>: add x6, x6, x5
| <__tsan_unaligned_read4+312>: stxr w7, x6, [x2]
| <__tsan_unaligned_read4+316>: cbnz w7, <__tsan_unaligned_read4+304>
This caused an infinite loop as the `stxr` instruction never completed successfully,
so `w7` was always 0.
Signed-off-by: Joey Gouly <joey.gouly@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20220405104733.11476-1-joey.gouly@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
CONFIG_SATA_LPM_MOBILE_POLICY was renamed to CONFIG_SATA_LPM_POLICY in
commit 4dd4d3deb502 ("ata: ahci: Rename CONFIG_SATA_LPM_MOBILE_POLICY
configuration item").
This can potentially cause problems as users would invisibly lose
configuration policy defaults when they built the new kernel. To
avoid such problems, switch back to the old name (even if it's wrong).
Suggested-by: Christoph Hellwig <hch@infradead.org>
Suggested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
There is often not a MAC address available in an EEPROM accessible by
Linux with Marvell devices. Instead the bootload has the MAC address
and directly programs it into the hardware. So don't consider an error
from of_get_mac_address() has fatal. However, the check was added for
the case where there is a MAC address in an the EEPROM, but the EEPROM
has not probed yet, and -EPROBE_DEFER is returned. In that case the
error should be returned. So make the check specific to this error
code.
Cc: Mauri Sandberg <maukka@ext.kapsi.fi>
Reported-by: Thomas Walther <walther-it@gmx.de>
Fixes: 42404d8f1c01 ("net: mv643xx_eth: process retval from of_get_mac_address")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220405000404.3374734-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
'OVS_CLONE_ATTR_EXEC' is an internal attribute that is used for
performance optimization inside the kernel. It's added by the kernel
while parsing user-provided actions and should not be sent during the
flow dump as it's not part of the uAPI.
The issue doesn't cause any significant problems to the ovs-vswitchd
process, because reported actions are not really used in the
application lifecycle and only supposed to be shown to a human via
ovs-dpctl flow dump. However, the action list is still incorrect
and causes the following error if the user wants to look at the
datapath flows:
# ovs-dpctl add-dp system@ovs-system
# ovs-dpctl add-flow "<flow match>" "clone(ct(commit),0)"
# ovs-dpctl dump-flows
<flow match>, packets:0, bytes:0, used:never,
actions:clone(bad length 4, expected -1 for: action0(01 00 00 00),
ct(commit),0)
With the fix:
# ovs-dpctl dump-flows
<flow match>, packets:0, bytes:0, used:never,
actions:clone(ct(commit),0)
Additionally fixed an incorrect attribute name in the comment.
Fixes: b233504033db ("openvswitch: kernel datapath clone action")
Signed-off-by: Ilya Maximets <i.maximets@ovn.org>
Acked-by: Aaron Conole <aconole@redhat.com>
Link: https://lore.kernel.org/r/20220404104150.2865736-1-i.maximets@ovn.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
KS8851 selects MICREL_PHY, which depends on PTP_1588_CLOCK_OPTIONAL, so
make KS8851 also depend on PTP_1588_CLOCK_OPTIONAL.
Fixes kconfig warning and build errors:
WARNING: unmet direct dependencies detected for MICREL_PHY
Depends on [m]: NETDEVICES [=y] && PHYLIB [=y] && PTP_1588_CLOCK_OPTIONAL [=m]
Selected by [y]:
- KS8851 [=y] && NETDEVICES [=y] && ETHERNET [=y] && NET_VENDOR_MICREL [=y] && SPI [=y]
ld.lld: error: undefined symbol: ptp_clock_register referenced by micrel.c
net/phy/micrel.o:(lan8814_probe) in archive drivers/built-in.a
ld.lld: error: undefined symbol: ptp_clock_index referenced by micrel.c
net/phy/micrel.o:(lan8814_ts_info) in archive drivers/built-in.a
Reported-by: kernel test robot <lkp@intel.com>
Fixes: ece19502834d ("net: phy: micrel: 1588 support for LAN8814 phy")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20220405065936.4105272-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
1) Incorrect comparison in bitmask .reduce, from Jeremy Sowden.
2) Missing GFP_KERNEL_ACCOUNT for dynamically allocated objects,
from Vasily Averin.
* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: nf_tables: memcg accounting for dynamically allocated objects
netfilter: bitwise: fix reduce comparisons
====================
Link: https://lore.kernel.org/r/20220405100923.7231-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
On a S905W-based system I get the following error:
debugfs: Directory 'c1105400.audio-controller' with parent 'P230-Q200' already present!
Turned out that multiple components having the same name triggers this
error in soc_init_component_debugfs(). With the patch the error is gone
and that's the debugfs entries.
/sys/kernel/debug/asoc/P230-Q200/acodec:c1105400.audio-controller
/sys/kernel/debug/asoc/P230-Q200/hdmi:c1105400.audio-controller
/sys/kernel/debug/asoc/P230-Q200/cpu:c1105400.audio-controller
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/38053baf-c33b-7fdf-7593-99b22153a9c0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Allow the component debugfs_prefix to be set from
snd_soc_component_driver. First use case is avoiding a duplicate
debugfs entry error in case a device has multiple components
which have the same name therefore.
Note that we don't set component->debugfs_prefix if it's set already.
That's needed because partially component->debugfs_prefix is set
before calling snd_soc_component_initialize().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/d18bff6a-1df1-5f95-0cf8-10dbaa62d7be@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
sc7280 platform
Update required clock-names used for MI2S primary path, VA macro's
codec memory path and HDMI path in sc7280 based platforms.
Update power domain names required for sc7280 platforms.
Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Co-developed-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
Signed-off-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
Link: https://lore.kernel.org/r/1647852981-27895-4-git-send-email-quic_srivasam@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add vdd mic bias supply, which is required to provide bias
for wcd938x codec.
Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Co-developed-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
Signed-off-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1647852981-27895-3-git-send-email-quic_srivasam@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Update dt-bindings for clocks as per ADSP bypass solutions, in which macro
dcodec GDSCs are enabled using power domains in lpass digital codec drivers.
Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Co-developed-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
Signed-off-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1647852981-27895-2-git-send-email-quic_srivasam@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
AK4613 has STEREO/TDM512/TDM256/TDM128 mode.
Renesas is the only user of ak4613 on upstream for now,
and is using it as STEREO mode, because of board connection.
Thus, current driver is supporting STEREO mode only, and other
modes are not supported.
But I noticed that I can try first 2ch out of TDM256 mode 8ch
Playback even in such a situation.
But because of board connection, I can't test full TDM256 mode,
and/or other TDM mode. Thus I don't want to add new DT propaty for now.
This patch enables TDM256 mode test by "ifdef style",
but it has no effect to current supported STEREO mode.
You can define AK4613_ENABLE_TDM_TEST to try TDM256 mode.
Please don't hesitate to break current code if you can add full TDM256
and/or other TDM mode. You don't need to care compatibility with Renesas.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/878rskp9l0.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
TDM support needs to use constraint_channels.
This patch renames current constraint to constraint_rates for it.
This is prepare for TDM support.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87a6d0p9l7.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current priv is using ->iface, but it is not good match
to support TDM. This patch adds ->ctrl1 instead of it.
This is prepare for TDM support.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87bkxgp9lh.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Renesas is only user of ak4613 on upstream, and it is tested
only under "clock consumer" because of board mounting situation.
Thus, "clock provider" is not supperted/tested.
This patch return error if it was setup as clock provider.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87czhwp9lq.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
ak4613 driver is assuming symmetric format.
Thus, we don't need to have asymmetric table for judging the
iface at .hw_param.
This patch cleanup ak4613_interface for it.
This is prepare for TDM support.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87ee2cp9lz.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We need to use mutex_lock() for priv->cnt / priv->iface,
but we are missing it at ak4613_dai_startup().
This patch adds missing mutex_lock() for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87fsmsp9m7.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Replace the last instance of acpi_bus_get_device(), added recently
by commit 87e59b36e5e2 ("spi: Support selection of the index of the
ACPI Spi Resource before alloc"), with acpi_fetch_acpi_dev() and
finally drop acpi_bus_get_device() that has no more users.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
|
|
Pull virtio fixes from Michael Tsirkin:
"Fixes and cleanups:
- A couple of mlx5 fixes related to cvq
- A couple of reverts dropping useless code (code that used it got
reverted earlier)"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vdpa: mlx5: synchronize driver status with CVQ
vdpa: mlx5: prevent cvq work from hogging CPU
Revert "virtio_config: introduce a new .enable_cbs method"
Revert "virtio: use virtio_device_ready() in virtio_device_restore()"
|
|
The CS35L45 is a 15 V Boosted Mono Class D Amplifier with DSP
Speaker Protection and Adaptive Battery Management.
This initial driver provides standard non-boosted audio operation
without the DSP.
Signed-off-by: James Schulman <james.schulman@cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220405135419.1230088-6-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This adds the schema binding for the Cirrus Logic CS35L45 Smart Amp
and associated header file.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220405135419.1230088-5-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Create a new kunit test for soc-utils and use it to test
snd_soc_tdm_params_to_bclk().
The test uses a table of values to avoid the possibility that an
on-the-fly generator contains the same algorithmic error as the
function-under-test and so fails to detect a bug.
There is no need to test every possible combination of values.
Enough test cases are included to give confidence that the function
is producing the correct results.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220405135419.1230088-4-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add a helper function snd_soc_tdm_params_to_bclk() to calculate
the bclk from params info and the tdm sots configuration.
When using a TDM frame of N slots of width W bits:
bclk = sample_rate * N * W
As a convenience to simplify calling code, if the slot count or
slot width are 0 a value will be obtained from the params. This
allows calling code to use this one function to handle cases of
TDM where only one parameter is fixed, or I2S where the slot width
is fixed (for example to set a 32-bit slot for 24-bit samples).
Also as a convenience the slot count can optionally be rounded up
to a multiple. This is mainly useful for I2S systems, since I2S has
two phases of LRCLK the number of slots is always a multiple of 2.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220405135419.1230088-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add a convenience macro for defining a single (mono) TLV control
with a signed value. This can already be done by using
SOC_DOUBLE_R_S_TLV() with the same address for left and right
registers, but a dedicated macro is more readable.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220405135419.1230088-2-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
After resuming from suspend-to-RAM, the MSRs that control CPU's
speculative execution behavior are not being restored on the boot CPU.
These MSRs are used to mitigate speculative execution vulnerabilities.
Not restoring them correctly may leave the CPU vulnerable. Secondary
CPU's MSRs are correctly being restored at S3 resume by
identify_secondary_cpu().
During S3 resume, restore these MSRs for boot CPU when restoring its
processor state.
Fixes: 772439717dbf ("x86/bugs/intel: Set proper CPU features and setup RDS")
Reported-by: Neelima Krishnan <neelima.krishnan@intel.com>
Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Tested-by: Neelima Krishnan <neelima.krishnan@intel.com>
Acked-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The mechanism to save/restore MSRs during S3 suspend/resume checks for
the MSR validity during suspend, and only restores the MSR if its a
valid MSR. This is not optimal, as an invalid MSR will unnecessarily
throw an exception for every suspend cycle. The more invalid MSRs,
higher the impact will be.
Check and save the MSR validity at setup. This ensures that only valid
MSRs that are guaranteed to not throw an exception will be attempted
during suspend.
Fixes: 7a9c2dd08ead ("x86/pm: Introduce quirk framework to save/restore extra MSR registers around suspend/resume")
Suggested-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com>
Acked-by: Borislav Petkov <bp@suse.de>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
AR context
In 1394 OHCI specification, descriptor of Asynchronous Receive DMA context
has timeStamp field in its trailer quadlet. The field is written by
the host controller for the time to receive asynchronous request
subaction in isochronous cycle time.
In Linux FireWire subsystem, the value of field is stored to fw_packet
structure and copied to fw_request structure as the part. The fw_request
structure is hidden from unit driver and passed as opaque pointer when
calling registered handler. It's inconvenient to the unit driver which
needs timestamp of packet.
This commit adds kernel API to pick up timestamp from opaque pointer to
fw_request structure.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20220405072221.226217-4-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
1394 OHCI specification defined Isochronous Cycle Timer Register to get
value of CYCLE_TIME register defined by IEEE 1394 for CSR architecture
defined by ISO/IEC 13213. Unit driver can calculate packet time by
compute with the value of CYCLE_TIME and timeStamp field in descriptor
of each isochronous and asynchronous context. The resolution of CYCLE_TIME
is 49.576 MHz, while the one of timeStamp is 8,000 Hz.
Current implementation of Linux FireWire subsystem allows the driver to
get the value of CYCLE_TIMER CSR register by transaction service. The
transaction service has overhead in regard of access to MMIO register.
This commit adds kernel API for unit driver to access the register
directly.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20220405072221.226217-3-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
(Hector Martin wrote)
This fixes segfaults when a card gets yanked off of the PCIe bus while
busy, e.g. with a userspace app trying to get the cycle time:
[8638860.994310] Call Trace:
[8638860.994313] ioctl_get_cycle_timer2+0x4f/0xd0 [firewire_core]
[8638860.994323] fw_device_op_ioctl+0xae/0x150 [firewire_core]
[8638860.994328] __x64_sys_ioctl+0x7d/0xb0
[8638860.994332] do_syscall_64+0x45/0x80
[8638860.994337] entry_SYSCALL_64_after_hwframe+0x44/0xae
(Takashi Sakamoto wrote)
As long as reading commit 20802224298c ("firewire: core: add forgotten
dummy driver methods, remove unused ones"), three functions are not
implemeted in dummy driver for reason; .read_csr, .write_csr, and
.set_config_rom.
In core of Linux FireWire subsystem, the callback of .set_config_rom is
under acquisition of mutual exclusive for local list of card. The
acquision is also done in process for removal of card, therefore it's
safe for missing implementation of .set_config_rom.
On the other hand, no lock primitive accompanies any call of .read_csr and
.write_csr. For userspace client, check of node shutdown is done in the
beginning of dispatch of ioctl request, while node shifts to shutdown
state in workqueue context enough after card shifts to dummy driver. It's
probable that these two functions are called for the dummy driver by the
code of userspace client. In-kernel unit driver has similar situation.
It's better to add implementation of the two functions for dummy driver.
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20220405072221.226217-2-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Fix:
sound/usb/midi.c: In function ‘snd_usbmidi_out_endpoint_create’:
sound/usb/midi.c:1389:2: error: case label does not reduce to an integer constant
case USB_ID(0xfc08, 0x0101): /* Unknown vendor Cable */
^~~~
See https://lore.kernel.org/r/YkwQ6%2BtIH8GQpuct@zn.tnic for the gory
details as to why it triggers with older gccs only.
[ A slight correction with parentheses around the argument by tiwai ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20220405151517.29753-3-bp@alien8.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The variable i is being assigned a value that is never read, it
is being re-assigned in the following for-loop. The assignment is
redundant and can be removed.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20220405135412.199251-1-colin.i.king@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
In systems with only a discrete i915 GPU, the acomp init will
always timeout for the PCH HDA controller instance.
Avoid the timeout by checking the PCI device hierarchy
whether any display class PCI device can be found on the system,
and at the same level as the HDA PCI device. If found, proceed
with the acomp init, which will wait until i915 probe is complete
and component binding can proceed. If no matching display
device is found, the audio component bind can be safely skipped.
The bind timeout will still be hit if the display is present
in the system, but i915 driver does not bind to it by configuration
choice or probe error. In this case the 60sec timeout will be
hit.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Acked-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://lore.kernel.org/r/20220405123622.2874457-1-kai.vehmanen@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
iommu_get_domain_for_dev() is already perfectly happy to return NULL
if the given device has no IOMMU. Drop the unnecessary check in favour
of just handling that condition appropriately.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/9b506b4a4fe8a7f40aa8bad1aafc82426cf3dd92.1649165210.git.robin.murphy@arm.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Currently when XDP rings are created, each descriptor gets its DD bit
set, which turns out to be the wrong approach as it can lead to a
situation where more descriptors get cleaned than it was supposed to,
e.g. when AF_XDP busy poll is run with a large batch size. In this
situation, the driver would request for more buffers than it is able to
handle.
Fix this by not setting the DD bits in ice_xdp_alloc_setup_rings(). They
should be initialized to zero instead.
Fixes: 9610bd988df9 ("ice: optimize XDP_TX workloads")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Shwetha Nagaraju <shwetha.nagaraju@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
ICE_DOWN is dedicated for pf->state. Check for ICE_VSI_DOWN being set on
vsi->state in ice_xsk_wakeup().
Fixes: 2d4238f55697 ("ice: Add support for AF_XDP")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Shwetha Nagaraju <shwetha.nagaraju@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Unfortunately, the ice driver doesn't respect the RCU critical section that
XSK wakeup is surrounded with. To fix this, add synchronize_rcu() calls to
paths that destroy resources that might be in use.
This was addressed in other AF_XDP ZC enabled drivers, for reference see
for example commit b3873a5be757 ("net/i40e: Fix concurrency issues
between config flow and XSK")
Fixes: efc2214b6047 ("ice: Add support for XDP")
Fixes: 2d4238f55697 ("ice: Add support for AF_XDP")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Shwetha Nagaraju <shwetha.nagaraju@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
- prevent deleting subvolume with active swapfile
- fix qgroup reserve limit calculation overflow
- remove device count in superblock and its item in one transaction so
they cant't get out of sync
- skip defragmenting an isolated sector, this could cause some extra IO
- unify handling of mtime/permissions in hole punch with fallocate
- zoned mode fixes:
- remove assert checking for only single mode, we have the
DUP mode implemented
- fix potential lockdep warning while traversing devices
when checking for zone activation
* tag 'for-5.18-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: prevent subvol with swapfile from being deleted
btrfs: do not warn for free space inode in cow_file_range
btrfs: avoid defragging extents whose next extents are not targets
btrfs: fix fallocate to use file_modified to update permissions consistently
btrfs: remove device item and update super block in the same transaction
btrfs: fix qgroup reserve overflow the qgroup limit
btrfs: zoned: remove left over ASSERT checking for single profile
btrfs: zoned: traverse devices under chunk_mutex in btrfs_can_activate_zone
|
|
At the moment the GIC IRQ domain translation routine happily converts
ACPI table GSI numbers below 16 to GIC SGIs (Software Generated
Interrupts aka IPIs). On the Devicetree side we explicitly forbid this
translation, actually the function will never return HWIRQs below 16 when
using a DT based domain translation.
We expect SGIs to be handled in the first part of the function, and any
further occurrence should be treated as a firmware bug, so add a check
and print to report this explicitly and avoid lengthy debug sessions.
Fixes: 64b499d8df40 ("irqchip/gic-v3: Configure SGIs as standard interrupts")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220404110842.2882446-1-andre.przywara@arm.com
|
|
It turns out that our polling of RWP is totally wrong when checking
for it in the redistributors, as we test the *distributor* bit index,
whereas it is a different bit number in the RDs... Oopsie boo.
This is embarassing. Not only because it is wrong, but also because
it took *8 years* to notice the blunder...
Just fix the damn thing.
Fixes: 021f653791ad ("irqchip: gic-v3: Initial support for GICv3")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Link: https://lore.kernel.org/r/20220315165034.794482-2-maz@kernel.org
|
|
The way KVM drives GICv4.{0,1} is as follows:
- vcpu_load() makes the VPE resident, instructing the RD to start
scanning for interrupts
- just before entering the guest, we check that the RD has finished
scanning and that we can start running the vcpu
- on preemption, we deschedule the VPE by making it invalid on
the RD
However, we are preemptible between the first two steps. If it so
happens *and* that the RD was still scanning, we nonetheless write
to the GICR_VPENDBASER register while Dirty is set, and bad things
happen (we're in UNPRED land).
This affects both the 4.0 and 4.1 implementations.
Make sure Dirty is cleared before performing the deschedule,
meaning that its_clear_vpend_valid() becomes a sort of full VPE
residency barrier.
Reported-by: Jingyi Wang <wangjingyi11@huawei.com>
Tested-by: Nianyao Tang <tangnianyao@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Fixes: 57e3cebd022f ("KVM: arm64: Delay the polling of the GICR_VPENDBASER.Dirty bit")
Link: https://lore.kernel.org/r/4aae10ba-b39a-5f84-754b-69c2eb0a2c03@huawei.com
|
|
If devm_platform_ioremap_resource() fails, it never returns
NULL, replace NULL check with IS_ERR().
Fixes: a6199bb514d8 ("irqchip: Add Qualcomm MPM controller driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220316025100.1758413-1-yangyingliang@huawei.com
|
|
If MAILBOX is n, building fails:
drivers/irqchip/irq-qcom-mpm.o: In function `mpm_pd_power_off':
irq-qcom-mpm.c:(.text+0x174): undefined reference to `mbox_send_message'
irq-qcom-mpm.c:(.text+0x174): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `mbox_send_message'
Make QCOM_MPM depends on MAILBOX to fix this.
Fixes: a6199bb514d8 ("irqchip: Add Qualcomm MPM controller driver")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220317131956.30004-1-yuehaibing@huawei.com
|
|
In 6f98a4bfee72 ("random: block in /dev/urandom"), we tried to make a
successful try_to_generate_entropy() call *required* if the RNG was not
already initialized. Unfortunately, weird architectures and old
userspaces combined in TCG test harnesses, making that change still not
realistic, so it was reverted in 0313bc278dac ("Revert "random: block in
/dev/urandom"").
However, rather than making a successful try_to_generate_entropy() call
*required*, we can instead make it *best-effort*.
If try_to_generate_entropy() fails, it fails, and nothing changes from
the current behavior. If it succeeds, then /dev/urandom becomes safe to
use for free. This way, we don't risk the regression potential that led
to us reverting the required-try_to_generate_entropy() call before.
Practically speaking, this means that at least on x86, /dev/urandom
becomes safe. Probably other architectures with working cycle counters
will also become safe. And architectures with slow or broken cycle
counters at least won't be affected at all by this change.
So it may not be the glorious "all things are unified!" change we were
hoping for initially, but practically speaking, it makes a positive
impact.
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
Now that all in-kernel users of default_attrs for the kobj_type are gone
and converted to properly use the default_groups pointer instead, it can
be safely removed.
There is one standard way to create sysfs files in a kobj_type, and not
two like before, causing confusion as to which should be used.
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Link: https://lore.kernel.org/r/20220106133151.607703-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
