| Age | Commit message (Collapse) | Author |
|---|
|
The 82599 KX4 device defaults to legacy power management, or APME. This
puts the device into ACPI mode, which allows more robust WoL setups to
work properly.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 1f87f7d3 (cfg80211: add rfkill support) added ERFKILL
to asm-generic/errno.h, but alpha, mips, parisc and sparc use
their own numbering scheme and do not include asm-generic/errno.h.
We need to add definition of ERFKILL for them.
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
From the perspective of most users of recent systems, disabling Host
Protected Area (HPA) can break vendor RAID formats, GPT partitions and
risks corrupting firmware or overwriting vendor system recovery tools.
Unfortunately the original (kernels < 2.6.30) behavior (unconditionally
disabling HPA and using full disk capacity) was introduced at the time
when the main use of HPA was to make the drive look small enough for the
BIOS to allow the system to boot with large capacity drives.
Thus to allow the maximum compatibility with the existing setups (using
HPA and partitioned with HPA disabled) we automically disable HPA if
any partitions overlapping HPA are detected. Additionally HPA can also
be disabled using the "nohpa" module parameter (i.e. "ide_core.nohpa=0.0"
to disable HPA on /dev/hda).
v2:
Fix ->resume HPA support.
While at it:
- remove stale "idebus=" entry from Documentation/kernel-parameters.txt
Cc: Robert Hancock <hancockrwd@gmail.com>
Cc: Frans Pop <elendil@planet.nl>
Cc: "Andries E. Brouwer" <Andries.Brouwer@cwi.nl>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
[patch description was based on input from Alan Cox and Frans Pop]
Emphatically-Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Use ->probed_capacity to store native device capacity for ATA disks.
* Add ->set_capacity method to struct ide_disk_ops.
* Implement disk device ->set_capacity method for ATA disks.
* Implement block device ->set_capacity method.
v2:
* Check if LBA and HPA are supported in ide_disk_set_capacity().
* According to the spec the SET MAX ADDRESS command shall be
immediately preceded by a READ NATIVE MAX ADDRESS command.
* Add ide_disk_hpa_{get_native,set}_capacity() helpers.
Together with the previous patch adding ->set_capacity block device
method this allows automatic disabling of Host Protected Area (HPA)
if any partitions overlapping HPA are detected.
Cc: Robert Hancock <hancockrwd@gmail.com>
Cc: Frans Pop <elendil@planet.nl>
Cc: "Andries E. Brouwer" <Andries.Brouwer@cwi.nl>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Emphatically-Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Add ->set_capacity block device method and use it in rescan_partitions()
to attempt enabling native capacity of the device upon detecting the
partition which exceeds device capacity.
* Add GENHD_FL_NATIVE_CAPACITY flag to try limit attempts of enabling
native capacity during partition scan.
Together with the consecutive patch implementing ->set_capacity method in
ide-gd device driver this allows automatic disabling of Host Protected Area
(HPA) if any partitions overlapping HPA are detected.
Cc: Robert Hancock <hancockrwd@gmail.com>
Cc: Frans Pop <elendil@planet.nl>
Cc: "Andries E. Brouwer" <Andries.Brouwer@cwi.nl>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Emphatically-Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
The current warning message says only about the kernel's action taken
without mentioning the underlying reason behind it.
Noticed-by: Robert Hancock <hancockrwd@gmail.com>
Cc: Frans Pop <elendil@planet.nl>
Cc: "Andries E. Brouwer" <Andries.Brouwer@cwi.nl>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Emphatically-Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
pdc202xx_reset() calls pdc202xx_reset_host() twice, for both channels, while
that function actually twiddles the single, shared software reset bit -- the
net effect is a duplicated reset and horrendous 4 second delay happening not
only on a channel reset but also when dma_lost_irq() and dma_clear() methods
are called. Fold pdc202xx_reset_host() into pdc202xx_reset(), fix printk(),
and move it before the actual reset...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Commit ac95beedf8bc97b24f9540d4da9952f07221c023 (ide: add struct ide_port_ops
(take 2)) erroneously converted the driver's dma_timeout() and dma_lost_irq()
methods to call the driver's resetproc() method regardless of whether it was
defined for this specific controller while it hadn't been defined and hence
called for PDC20246. So the dma_clear() method, the successor of dma_timeout(),
shouldn't exist and the dma_lost_irq() method should be standard for PDC20246.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6
|
|
This patch removes the forcedeth device ids from pci_ids.h
The forcedeth driver uses the device id constants directly in its source
file.
[ Need to keep PCI_DEVICE_ID_NVIDIA_NVENET_15 in order to keep
drivers/pci/quirks.c building -DaveM ]
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds a new device id for mcp89 chipset.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch removes the device id macros and instead uses the constants
directly.
The areas in which logic expressions where using the macros now instead
use feature/workaround flags.
No new functionality has been introduced in this patch, only clean up of
flags and macros.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove model information, encoding/decoding and reduce bookkeeping.
This, besides removing a lot of code and cleaning up the code, also
enables these features on many more CPUs that were enumerated before.
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
LKML-Reference: <1244224637.8212.6.camel@ht.satnam>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
|
|
The commit 13f040f9e55d41e92e485389123654971e03b819 made another
regression, the missing update of runtime->hw_ptr_interrupt.
Since this field is only checked in snd_pcmupdate__hw_ptr_interrupt(),
not in snd_pcm_update_hw_ptr(), it must be updated before the hw_ptr
change check.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/linux-2.6-iommu into core/iommu
|
|
Merge reason: This branch was on an -rc5 base so pull almost-2.6.30
to resync with the latest upstream fixes and make sure
the combination works fine.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Some device drivers map the same physical address multiple times to a
dma address. Without an IOMMU this results in the same dma address being
put into the dma-debug hash multiple times. With a first-fit match in
hash_bucket_find() this function may return the wrong dma_debug_entry.
This can result in false positive warnings. This patch fixes it by
changing the first-fit behavior of hash_bucket_find() into a best-fit
algorithm.
Reported-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Reported-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Cc: lethal@linux-sh.org
Cc: just.for.lkml@googlemail.com
Cc: hancockrwd@gmail.com
Cc: jens.axboe@oracle.com
Cc: bharrosh@panasas.com
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: <stable@kernel.org>
LKML-Reference: <20090605104132.GE24836@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
The first snapshot reading often occur before any events have
been read in the mapped perfcounter files.
Just wait until we have at least one event before starting the
snapshot, or the delay before the first set of entries to be
displayed may be long in case of low refresh rate.
Note: we could also use a semaphore to wait before
"print_entries" number of eveents is reached, but again this
value is tunable and we can't ensure we will even reach it.
Also we could base on a default mimimum set of entries for the
first refresh, say 15, but again, the minimal sample is
tunable, and we could end up displaying nothing until we have a
minimal default set of events, which can take some time in case
of high samples filters.
Hence this simple solution which partially covers the default
case.
[ Impact: fix display artifacts in perf top ]
Signed-off-by: Frederic Weisbecker <fweisbeec@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <1244322643-6447-1-git-send-email-fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
vfree() does it's own 'NULL' check,so no need for check before
calling it.
Signed-off-by: Figo.zhang <figo1802@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
x86/pci: fix mmconfig detection with 32bit near 4g
PCI: use fixed-up device class when configuring device
|
|
CONFIG_IMA=y inode activity leaks iint_cache and radix_tree_node objects
until the system runs out of memory. Nowhere is calling ima_inode_free()
a.k.a. ima_iint_delete(). Fix that by calling it from destroy_inode().
Signed-off-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Also update fs/cifs/CHANGES
Signed-off-by: Steve French <sfrench@us.ibm.com>
|
|
We have a bit of a problem with the uid= option. The basic issue is that
it means too many things and has too many side-effects.
It's possible to allow an unprivileged user to mount a filesystem if the
user owns the mountpoint, /bin/mount is setuid root, and the mount is
set up in /etc/fstab with the "user" option.
When doing this though, /bin/mount automatically adds the "uid=" and
"gid=" options to the share. This is fortunate since the correct uid=
option is needed in order to tell the upcall what user's credcache to
use when generating the SPNEGO blob.
On a mount without unix extensions this is fine -- you generally will
want the files to be owned by the "owner" of the mount. The problem
comes in on a mount with unix extensions. With those enabled, the
uid/gid options cause the ownership of files to be overriden even though
the server is sending along the ownership info.
This means that it's not possible to have a mount by an unprivileged
user that shows the server's file ownership info. The result is also
inode permissions that have no reflection at all on the server. You
simply cannot separate ownership from the mode in this fashion.
This behavior also makes MultiuserMount option less usable. Once you
pass in the uid= option for a mount, then you can't use unix ownership
info and allow someone to share the mount.
While I'm not thrilled with it, the only solution I can see is to stop
making uid=/gid= force the overriding of ownership on mounts, and to add
new mount options that turn this behavior on.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
|
|
Arjan noticed this bug in the perf annotate help output:
-s, --symbol <file> symbol to annotate
that should be <symbol> instead.
Reported-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
the "perf report" utility crashed in some circumstances
because the "sym" stack variable was not initialized before used
(as also proven by valgrind).
With this fix both the crash goes away and valgrind no longer complains.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
ext3/4 with synchronous writes gets wedged by Postfix
Fix nobh_truncate_page() to not pass stack garbage to get_block()
|
|
Right now kernel debug info does not get resolved by default, because
we dont know where to look for the vmlinux.
The -k option can be used for that - but if no option is given, pick
up vmlinux files in the current directory - in case a kernel hacker
runs profiling from the source directory that the kernel was built in.
The real solution would be to embedd the location (and perhaps the
date/timestamp) of the vmlinux file in /proc/kallsyms, so that
tools can pick it up automatically.
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[libata] pata_ali: Use IGN_SIMPLEX
|
|
gcc warned about this bug:
util/parse-events.c: In function ‘parse_generic_hw_symbols’:
util/parse-events.c:175: warning: comparison is always false due to limited range of data type
util/parse-events.c:182: warning: comparison is always false due to limited range of data type
util/parse-events.c:190: warning: comparison is always false due to limited range of data type
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Several people have suggested that 'perf' has become a full-fledged
tool that should be moved out of Documentation/. Move it to the
(new) tools/ directory.
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Merge reason: Pick up the latest fixes before the -v8 perfcounters
release.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Add new perf sub-command to display annotated source code:
$ perf annotate decode_tree_entry
------------------------------------------------
Percent | Source code & Disassembly of /home/mingo/git/git
------------------------------------------------
:
: /home/mingo/git/git: file format elf64-x86-64
:
:
: Disassembly of section .text:
:
: 00000000004a0da0 <decode_tree_entry>:
: *modep = mode;
: return str;
: }
:
: static void decode_tree_entry(struct tree_desc *desc, const char *buf, unsigned long size)
: {
3.82 : 4a0da0: 41 54 push %r12
: const char *path;
: unsigned int mode, len;
:
: if (size < 24 || buf[size - 21])
0.17 : 4a0da2: 48 83 fa 17 cmp $0x17,%rdx
: *modep = mode;
: return str;
: }
:
: static void decode_tree_entry(struct tree_desc *desc, const char *buf, unsigned long size)
: {
0.00 : 4a0da6: 49 89 fc mov %rdi,%r12
0.00 : 4a0da9: 55 push %rbp
3.37 : 4a0daa: 53 push %rbx
: const char *path;
: unsigned int mode, len;
:
: if (size < 24 || buf[size - 21])
0.08 : 4a0dab: 76 73 jbe 4a0e20 <decode_tree_entry+0x80>
0.00 : 4a0dad: 80 7c 16 eb 00 cmpb $0x0,-0x15(%rsi,%rdx,1)
3.48 : 4a0db2: 75 6c jne 4a0e20 <decode_tree_entry+0x80>
: static const char *get_mode(const char *str, unsigned int *modep)
: {
: unsigned char c;
: unsigned int mode = 0;
:
: if (*str == ' ')
1.94 : 4a0db4: 0f b6 06 movzbl (%rsi),%eax
0.39 : 4a0db7: 3c 20 cmp $0x20,%al
0.00 : 4a0db9: 74 65 je 4a0e20 <decode_tree_entry+0x80>
: return NULL;
:
: while ((c = *str++) != ' ') {
0.06 : 4a0dbb: 89 c2 mov %eax,%edx
: if (c < '0' || c > '7')
1.99 : 4a0dbd: 31 ed xor %ebp,%ebp
: unsigned int mode = 0;
:
: if (*str == ' ')
: return NULL;
:
: while ((c = *str++) != ' ') {
1.74 : 4a0dbf: 48 8d 5e 01 lea 0x1(%rsi),%rbx
: if (c < '0' || c > '7')
0.00 : 4a0dc3: 8d 42 d0 lea -0x30(%rdx),%eax
0.17 : 4a0dc6: 3c 07 cmp $0x7,%al
0.00 : 4a0dc8: 76 0d jbe 4a0dd7 <decode_tree_entry+0x37>
0.00 : 4a0dca: eb 54 jmp 4a0e20 <decode_tree_entry+0x80>
0.00 : 4a0dcc: 0f 1f 40 00 nopl 0x0(%rax)
16.57 : 4a0dd0: 8d 42 d0 lea -0x30(%rdx),%eax
0.14 : 4a0dd3: 3c 07 cmp $0x7,%al
0.00 : 4a0dd5: 77 49 ja 4a0e20 <decode_tree_entry+0x80>
: return NULL;
: mode = (mode << 3) + (c - '0');
3.12 : 4a0dd7: 0f b6 c2 movzbl %dl,%eax
: unsigned int mode = 0;
:
: if (*str == ' ')
: return NULL;
:
: while ((c = *str++) != ' ') {
0.00 : 4a0dda: 0f b6 13 movzbl (%rbx),%edx
16.74 : 4a0ddd: 48 83 c3 01 add $0x1,%rbx
: if (c < '0' || c > '7')
: return NULL;
: mode = (mode << 3) + (c - '0');
The first column is the percentage of samples that arrived on that
particular line - relative to the total cost of the function.
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Prepare for the 'perf annotate' implementation by splitting off
builtin-annotate.c from builtin-report.c.
( We keep this commit separate to ease the later librarization
of the facilities that perf-report and perf-annotate shares. )
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Added support for the new xps tft controller. The new core
has PLB interface support in addition to existing DCR interface.
Removed platform device support as both MicroBlaze and PowerPC
use device tree.
Previously, the dcr interface was assumed to be used in mmio mode,
and the register space of the dcr interface was precomputed and stuffed
into the device tree. This driver now makes use of the new dcr
infrastructure to represent the dcr interface. This enables the dcr
interface to be connected directly to a native dcr interface in a clean
way.
Added compatibility for ml507 dvi core.
Signed-off-by: Suneel <suneelg@xilinx.com>
Signed-off-by: Stephen Neuendorffer <stephen.neuendorffer@xilinx.com>
Signed-off-by: John Linn <john.linn@xilinx.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
|
|
Fix a typo in the commit 13f040f9e55d41e92e485389123654971e03b819
ALSA: PCM midlevel: Do not update hw_ptr_jiffies when hw_ptr is not changed
which causes obvious problems with PA.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This is an updated document covering the internal API for the debugfs
filesystem. Thanks to Shen Feng for suggesting that I put this text here
and noting that the old LWN version was rather out of date.
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Reported-by: Shen Feng <shen@cn.fujitsu.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
As subject says, add dts files for Xilinx ML510 reference design with
the PCI host bridge device.
Signed-off-by: Roderick Colenbrander <thunderbird2k@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Signed-off-by: Roderick Colenbrander <thunderbird2k@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
This patch refactors some of the xilinx_intc interrupt controller driver
and adds support for cascading an i8259 off one of the irq lines.
This patch was based on the ML510 support work done by Roderick
Colenbrander.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
This patch adds support for the Xilinx plbv46-pci-1.03.a PCI host
bridge IPcore.
Signed-off-by: Roderick Colenbrander <thunderbird2k@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Also fix a misalignment in usage string printing.
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Also add perf list to command-list.txt.
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Also update other areas of the help texts.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Also standardize the cache printout (so that it can be pasted back
into the command) and sort out the aliases.
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
perf list: List all the available event types which can be used in
-e (--event) options.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Extend generic event enumeration with the PERF_TYPE_HW_CACHE
method.
This is a 3-dimensional space:
{ L1-D, L1-I, L2, ITLB, DTLB, BPU } x
{ load, store, prefetch } x
{ accesses, misses }
User-space passes in the 3 coordinates and the kernel provides
a counter. (if the hardware supports that type and if the
combination makes sense.)
Combinations that make no sense produce a -EINVAL.
Combinations that are not supported by the hardware produce -ENOTSUP.
Extend the tools to deal with this, and rewrite the event symbol
parsing code with various popular aliases for the units and
access methods above. So 'l1-cache-miss' and 'l1d-read-ops' are
both valid aliases.
( x86 is supported for now, with the Nehalem event table filled in,
and with Core2 and Atom having placeholder tables. )
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
OK, that's probably the easiest way to do that, as much as I don't like it...
Since iget() et.al. will not accept I_FREEING (will wait to go away
and restart), and since we'd better have serialization between new/free
on fs data structures anyway, we can afford simply skipping I_FREEING
et.al. in insert_inode_locked().
We do that from new_inode, so it won't race with free_inode in any interesting
ways and it won't race with iget (of any origin; nfsd or in case of fs
corruption a lookup) since both still will wait for I_LOCK.
Reviewed-by: "Theodore Ts'o" <tytso@mit.edu>
Acked-by: Jan Kara <jack@suse.cz>
Tested-by: David Watson <dbwatson@ukfsn.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
