| Age | Commit message (Collapse) | Author |
|---|
|
Enable FLEXCAN_QUIRK_BROKEN_PERR_STATE for i.MX6 to report correct state
transitions.
Signed-off-by: Zhu Yi <yi.zhu5@cn.bosch.com>
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.11
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Add FLEXCAN_QUIRK_BROKEN_PERR_STATE for better description of the
missing error passive interrupt quirk.
Error interrupt flooding may happen if the broken error state quirk fix
is enabled. For example, in case there is singled out node on the bus
and the node sends a frame, then error interrupt flooding happens and
will not stop because the node cannot go to bus off. The flooding will
stop after another node connected to the bus again.
If high bitrate configured on the low end system, then the flooding
may causes performance issue, hence, this patch mitigates this by:
1. disable error interrupt upon error passive state transition
2. re-enable error interrupt upon error warning state transition
3. disable/enable error interrupt upon error active state transition
depends on FLEXCAN_QUIRK_BROKEN_WERR_STATE
In this way, the driver is still able to report correct state
transitions without additional latency. When there are bus problems,
flooding of error interrupts is limited to the number of frames required
to change state from error warning to error passive if the core has
[TR]WRN_INT connected (FLEXCAN_QUIRK_BROKEN_WERR_STATE is not enabled),
otherwise, the flooding is limited to the number of frames required to
change state from error active to error passive.
Signed-off-by: Zhu Yi <yi.zhu5@cn.bosch.com>
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.11
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Rename FLEXCAN_QUIRK_BROKEN_ERR_STATE to FLEXCAN_QUIRK_BROKEN_WERR_STATE
for better description of the missing [TR]WRN_INT quirk.
Signed-off-by: Zhu Yi <yi.zhu5@cn.bosch.com>
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.11
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Update state upon any interrupt to report correct state transitions in
case the flexcan core enabled the broken error state quirk fix.
Signed-off-by: Zhu Yi <yi.zhu5@cn.bosch.com>
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.11
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Add missing break statement in order to prevent the code from falling
through.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Cc: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20171016174029.GA19757@embeddedor.com
Signed-off-by: Borislav Petkov <bp@suse.de>
|
|
Split the Cavium EDAC entry into MIPS and ARM drivers because
they have different maintainers and mailing lists.
Add myself as additional maintainer to the ThunderX driver.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Sergey Temerkhanov <s.temerkhanov@gmail.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20171019064129.5064-1-jglauber@cavium.com
Signed-off-by: Borislav Petkov <bp@suse.de>
|
|
interrupt handling was broken with conversion to using regmap caching.
cached_gpio value was updated by boolean status instead of gpio reading.
Fixes: 8f38910ba4f6 ("pinctrl: mcp23s08: switch to regmap caching")
Tested-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Dmitry Mastykin <mastichi@gmail.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
On Asus laptop models X505BA, X505BP, X542BA and X542BP, the i2c-hid
touchpad (using a GPIO for interrupts) becomes unresponsive after a
few minutes of usage, or after placing two fingers on the touchpad,
which seems to have the effect of queuing up a large amount of input
data to be transferred.
When the touchpad is in unresponsive state, we observed that the GPIO
level-triggered interrupt is still at it's active level, however the
pinctrl-amd driver is not receiving/dispatching more interrupts at this
point.
After the initial interrupt arrives, amd_gpio_irq_mask() is called
however we then see amd_gpio_irq_handler() being called repeatedly for
the same irq; the interrupt mask is not taking effect because of the
following sequence of events:
- amd_gpio_irq_handler fires, reads and caches pin reg
- amd_gpio_irq_handler calls generic_handle_irq()
- During IRQ handling, amd_gpio_irq_mask() is called and modifies pin reg
- amd_gpio_irq_handler clears interrupt by writing cached value
The stale cached value written at the final stage undoes the masking.
Fix this by re-reading the register before clearing the interrupt.
I also spotted that the interrupt-clearing code can race against
amd_gpio_irq_mask() / amd_gpio_irq_unmask(), so add locking there.
Presumably this race was leading to the loss of interrupts.
After these changes, the touchpad appears to be working fine.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Acked-by: Shah, Nehal-bakulchandra <Nehal-Bakulchandra.shah@amd.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
If the connect status change is set during reset signaling, but
the status remains connected just retry port reset.
This solves an issue with connecting a 90W HP Thunderbolt 3 dock
with a Lenovo Carbon x1 (5th generation) which causes a 30min loop
of a high speed device being re-discovererd before usb ports starts
working.
[...]
[ 389.023845] usb 3-1: new high-speed USB device number 55 using xhci_hcd
[ 389.491841] usb 3-1: new high-speed USB device number 56 using xhci_hcd
[ 389.959928] usb 3-1: new high-speed USB device number 57 using xhci_hcd
[...]
This is caused by a high speed device that doesn't successfully go to the
enabled state after the second port reset. Instead the connection bounces
(connected, with connect status change), bailing out completely from
enumeration just to restart from scratch.
Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1716332
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.14-rc6
Here's a new metro-usb device id for another bar-code scanner.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
For CPUs which have an unknown or invalid CPU location (physical location)
assume that their cycle counters aren't syncronized across CPUs.
Signed-off-by: Helge Deller <deller@gmx.de>
Fixes: c8c3735997a3 ("parisc: Enhance detection of synchronous cr16 clocksources")
Cc: stable@vger.kernel.org # 4.13+
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
In testing target io in read write mix, we did indeed get into cases where
sqhd didn't update properly and slowly missed enough updates to shutdown
the queue.
Protect the updating sqhd by using cmpxchg, and for that turn the sqhd
field into a u32 so that cmpxchg works on it for all architectures.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
__cmpxchg_u64 is built and used outside CONFIG_64BIT and thus needs to
be exported. This fixes the following build error seen when building
parisc:allmodconfig.
ERROR: "__cmpxchg_u64" [drivers/net/ethernet/intel/i40e/i40e.ko] undefined!
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
As discussed on the debian-hppa list, double-wordcompare and exchange
operations fail on 32-bit kernels. Looking at the code, I realized that
the ",ma" completer does the wrong thing in the "ldw,ma 4(%r26), %r29"
instruction. This increments %r26 and causes the following store to
write to the wrong location.
Note by Helge Deller:
The patch applies cleanly to stable kernel series if this upstream
commit is merged in advance:
f4125cfdb300 ("parisc: Avoid trashing sr2 and sr3 in LWS code").
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Tested-by: Christoph Biedl <debian.axhn@manchmal.in-ulm.de>
Fixes: 89206491201c ("parisc: Implement new LWS CAS supporting 64 bit operations.")
Cc: stable@vger.kernel.org # 3.13+
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
I already Acked the patch, add my name to the list as well.
Signed-off-by: Laura Abbott <laura@labbott.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
Fix for stable:
- Fix DDI translation tables for BDW (Chris).
Critical fix:
- Fix GPU Hang on GVT (Changbin).
Other fixes:
- Fix eviction when GGTT is idle (Chris).
- CNL PLL fixes (Rodrigo).
- Fix pwrite into shmemfs (Chris).
- Mask bits for BXT and CHV L3 Workaround
WaProgramL3SqcReg1Default (Oscar).
* tag 'drm-intel-fixes-2017-10-18-1' of git://anongit.freedesktop.org/drm/drm-intel:
drm/i915: Use a mask when applying WaProgramL3SqcReg1Default
drm/i915: Report -EFAULT before pwrite fast path into shmemfs
drm/i915/cnl: Fix PLL initialization for HDMI.
drm/i915/cnl: Fix PLL mapping.
drm/i915: Use bdw_ddi_translations_fdi for Broadwell
drm/i915: Fix eviction when the GGTT is idle but full
drm/i915/gvt: Fix GPU hang after reusing vGPU instance across different guest OS
|
|
The pointer fs_ns is assigned from inode->i_ib->s_user_ns before
a null pointer check on inode, hence if inode is actually null we
will get a null pointer dereference on this assignment. Fix this
by only dereferencing inode after the null pointer check on
inode.
Detected by CoverityScan CID#1455328 ("Dereference before null check")
Fixes: 8db6c34f1dbc ("Introduce v3 namespaced file capabilities")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Cc: stable@vger.kernel.org
Acked-by: Serge Hallyn <serge@hallyn.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
|
|
|
|
The commit 78bcac7b2ae1e ("Input: add support for the STMicroelectronics
FingerTip touchscreen) used the 'touchscreen_parse_properties()' helper
function in order to get the value of common properties.
But, commit 78bcac7b2ae1e didn't set the capability of ABS_MT_POSITION_*
before calling touchscreen_parse_properties(). In result, the max_x and
max_y of 'struct touchscreen_properties' were not set.
Fixes: 78bcac7b2ae1e ("Input: add support for the STMicroelectronics FingerTip touchscreen")
Cc: stable@vger.kernel.org
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Step config setting for 5 wire touchscreen is incorrect for Y coordinates.
It was broken while we moved to DT. If you look close at the offending
commit bb76dc09ddfc ("input: ti_am33x_tsc: Order of TSC wires, made
configurable"), the change was:
- STEPCONFIG_XNP | STEPCONFIG_YPN;
+ ts_dev->bit_xn | ts_dev->bit_yp;
while bit_xn = STEPCONFIG_XNN and bit_yp = STEPCONFIG_YNN. Not quite the
same.
Fixes: bb76dc09ddfc ("input: ti_am33x_tsc: Order of TSC wires, made configurable")
Signed-off-by: Jeff Lance <j-lance1@ti.com>
[vigneshr@ti.com: Rebase to v4.14-rc1]
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Michael Nazzareno Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
into drm-fixes
Single amdgpu regression fix.
* 'drm-fixes-4.14' of git://people.freedesktop.org/~agd5f/linux:
Revert "drm/amdgpu: discard commands of killed processes"
|
|
[AV: in addition to the fix in previous commit]
Signed-off-by: Matthew Garrett <mjg59@google.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Reviewed-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
some nouveau fixes.
* 'linux-4.14' of git://github.com/skeggsb/linux:
drm/nouveau/fbcon: fix oops without fbdev emulation
drm/nouveau/kms/nv50: fix oops during DP IRQ handling on non-MST boards
drm/nouveau/bsp/g92: disable by default
drm/nouveau/mmu: flush tlbs before deleting page tables
|
|
This is similar to an earlier commit 52dfcc5ccfbb ("drm/nouveau: fix for
disabled fbdev emulation"), but protects all occurrences of helper.fbdev
in the source.
I see oops in nouveau_fbcon_accel_save_disable() called from
nouveau_fbcon_set_suspend_work() on Linux 3.13 when
CONFIG_DRM_FBDEV_EMULATION option is disabled.
Signed-off-by: Pavel Roskin <plroskin@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
Add my name to the kernel enforcement statement as it is something I
support speaking on my own behalf and not a statement of my current
employer.
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pull xfs fixes from Darrick Wong:
- fix some more CONFIG_XFS_RT related build problems
- fix data loss when writeback at eof races eofblocks gc and loses
- invalidate page cache after fs finishes a dio write
- remove dirty page state when invalidating pages so releasepage does
the right thing when handed a dirty page
* tag 'xfs-4.14-fixes-6' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: move two more RT specific functions into CONFIG_XFS_RT
xfs: trim writepage mapping to within eof
fs: invalidate page cache after end_io() in dio completion
xfs: cancel dirty pages on invalidation
|
|
Pull block fixes from Jens Axboe:
"Three small fixes:
- A fix for skd, it was using kfree() to free a structure allocate
with kmem_cache_alloc().
- Stable fix for nbd, fixing a regression using the normal ioctl
based tools.
- Fix for a previous fix in this series, that fixed up
inconsistencies between buffered and direct IO"
* 'for-linus' of git://git.kernel.dk/linux-block:
fs: Avoid invalidation in interrupt context in dio_complete()
nbd: don't set the device size until we're connected
skd: Use kmem_cache_free
|
|
Currently, if a frame is lost of command fails as part of initial
association create for a new controller, the new controller connection
request will immediately fail.
Add in an immediate 3 retry loop before giving up.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Add missing iowait head initialization.
Fix irqsave vs irq: wait_event_lock_irq() doesn't do irq save/restore
Fixes: 36715cf4b366 ("nvme_fc: replace ioabort msleep loop with completion”)
Cc: <stable@vger.kernel.org> # 4.13
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Tested-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Andrey used the syzkaller fuzzer to find an out-of-bounds memory
access in usb_get_bos_descriptor(). The code wasn't checking that the
next usb_dev_cap_header structure could fit into the remaining buffer
space.
This patch fixes the error and also reduces the bNumDeviceCaps field
in the header to match the actual number of capabilities found, in
cases where there are fewer than expected.
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This causes instability in piglit. It's fixed in drm-next with:
515c6faf85970af529953ec137b4b6fcb3272e25
1650c14b459ff9c85767746f1ef795a780653128
214a91e6bfabaa6cbfa692df8732000aab050795
29d253553559dba919315be847f4f2cce29edd42
79867462634836ee5c39a2cdf624719feeb189bd
This reverts commit 6af0883ed9770cf9b0a4f224c91481484cd1b025.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The channel value for requesting server remote invalidating local memory
registration should be 0x00000002
Signed-off-by: Long Li <longli@microsoft.com>
Signed-off-by: Steve French <smfrench@gmail.com>
|
|
Update reading the EA using increasingly larger buffer sizes
until the response will fit in the buffer, or we exceed the
(arbitrary) maximum set to 64kb.
Without this change, a user is able to add more and more EAs using
setfattr until the point where the total space of all EAs exceed 2kb
at which point the user can no longer list the EAs at all
and getfattr will abort with an error.
The same issue still exists for EAs in SMB1.
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Reported-by: Xiaoli Feng <xifeng@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
|
|
SMB3.1.1 is most secure and recent dialect. Fixup labels and lengths
for sMB3.1.1 signing and encryption.
Signed-off-by: Steve French <smfrench@gmail.com>
CC: Stable <stable@vger.kernel.org>
|
|
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Adding myself to the list as I missed the window to be in the original patch.
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Olof Johansson <olof@lixom.net>
Cc: Juergen Gross <jgross@suse.com>
Cc: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Eduardo Valentin <eduval@amazon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: Jérémy Lefaure <jeremy.lefaure@lse.epita.fr>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
This commit fixes the duplicate inline declaration specifier in
tpm2_rc_value which caused a warning
Signed-off-by: Ruben Roy <rubenroy2005@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Use __le32 type for data in that format.
Fixes: 0edbfea537d1 ("tpm/tpm_tis_spi: Add support for spi phy")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
|
|
The local variable 'handle' should have the type __be32 instead of u32.
Fixes: 745b361e989a ("tpm: infrastructure for TPM spaces")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
|
|
The local variable 'attrs' should have the type __be32 instead of u32.
Fixes: 58472f5cd4f6 ("tpm: validate TPM 2.0 commands")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
|
|
tpm_transmit() does not offer an explicit interface to indicate the number
of valid bytes in the communication buffer. Instead, it relies on the
commandSize field in the TPM header that is encoded within the buffer.
Therefore, ensure that a) enough data has been written to the buffer, so
that the commandSize field is present and b) the commandSize field does not
announce more data than has been written to the buffer.
This should have been fixed with CVE-2011-1161 long ago, but apparently
a correct version of that patch never made it into the kernel.
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
The TPM can choose one of two ways to react to the TPM2_SelfTest command.
It can either run all self tests synchronously and then return RC_SUCCESS
once all tests were successful. Or it can choose to run the tests
asynchronously and return RC_TESTING immediately while the self tests still
execute in the background.
The previous implementation apparently was not aware of those possibilities
and attributed RC_TESTING to some prototype chips instead. With this change
the return code of TPM2_SelfTest is interpreted correctly, i.e. the self
test result is polled if and only if RC_TESTING is received.
Unfortunately, the polling cannot be done in the most straightforward way.
If RC_TESTING is received, ideally the code should now poll the
selfTestDone bit in the STS register, as this avoids sending more commands,
that might interrupt self tests executing in the background and thus
prevent them from ever completing. But it cannot be guaranteed that this
bit is correctly implemented for all devices, so the next best thing would
be to use TPM2_GetTestResult to query the test result. But the response to
that command can be very long, and the code currently lacks the
capabilities for efficient unmarshalling, so it is difficult to execute
this command.
Therefore, we simply run the TPM2_SelfTest command in a loop, which should
complete eventually, since we only request the execution of self tests that
have not yet been done.
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
In order to avoid delaying the code longer than necessary while still
giving the TPM enough time to execute the self tests asynchronously, start
with a small delay between two polls and increase it each round.
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
tpm2_do_selftest is only used during initialization of the TPM to ensure
that the device functions correctly. Therefore, it is sufficient to request
only missing self tests (parameter full_test=0), not a reexecution of all
self tests, as was done before. This allows for a faster execution of this
command.
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
The buffers used as tx_buf/rx_buf in a SPI transfer need to be DMA-safe.
This cannot be guaranteed for the buffers passed to tpm_tis_spi_read_bytes
and tpm_tis_spi_write_bytes. Therefore, we need to use our own DMA-safe
buffer and copy the data to/from it.
The buffer needs to be allocated separately, to ensure that it is
cacheline-aligned and not shared with other data, so that DMA can work
correctly.
Fixes: 0edbfea537d1 ("tpm/tpm_tis_spi: Add support for spi phy")
Cc: stable@vger.kernel.org
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
This patch gets rid of dealing with intermediate flag for start method
and use start method value from ACPI table directly.
For ARM64, the locality is handled by Trust Zone in FW. The layout
does not have crb_regs_head. It is hitting the following line.
dev_warn(dev, FW_BUG "Bad ACPI memory layout");
Current code excludes CRB_FL_ACPI_START for this check. Now since
ARM64 support for TPM CRB is added, CRB_FL_CRB_SMC_START should also be
excluded from this check.
For goIdle and cmdReady where code was excluding CRB_FL_ACPI_START only
(do nothing for ACPI start method), CRB_FL_CRB_SMC_START was also
excluded as ARM64 SMC start method does not have TPM_CRB_CTRL_REQ.
However with special PPT workaround requiring CRB_FL_CRB_START to be
set in addition to CRB_FL_ACPI_START and the addition flag of SMC
start method CRB_FL_CRB_SMC_START, the code has become difficult to
maintain and undrestand. It is better to make code deal with start
method value from ACPI table directly.
Signed-off-by: Jiandi An <anjiandi@codeaurora.org>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Making cmd_getticks 'const' introduced a couple of harmless warnings:
drivers/char/tpm/tpm_tis_core.c: In function 'probe_itpm':
drivers/char/tpm/tpm_tis_core.c:469:31: error: passing argument 2 of 'tpm_tis_send_data' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
rc = tpm_tis_send_data(chip, cmd_getticks, len);
drivers/char/tpm/tpm_tis_core.c:477:31: error: passing argument 2 of 'tpm_tis_send_data' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
rc = tpm_tis_send_data(chip, cmd_getticks, len);
drivers/char/tpm/tpm_tis_core.c:255:12: note: expected 'u8 * {aka unsigned char *}' but argument is of type 'const u8 * {aka const unsigned char *}'
static int tpm_tis_send_data(struct tpm_chip *chip, u8 *buf, size_t len)
This changes the related functions to all take 'const' pointers
so that gcc can see this as being correct. I had to slightly
modify the logic around tpm_tis_spi_transfer() for this to work
without introducing ugly casts.
Cc: stable@vger.kernel.org
Fixes: 5e35bd8e06b9 ("tpm_tis: make array cmd_getticks static const to shink object code size")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Don't populate array cmd_getticks on the stack, instead make it static
const. Makes the object code smaller by over 160 bytes:
Before:
text data bss dec hex filename
18813 3152 128 22093 564d drivers/char/tpm/tpm_tis_core.o
After:
text data bss dec hex filename
18554 3248 128 21930 55aa drivers/char/tpm/tpm_tis_core.o
Cc: stable@vger.kernel.org
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
