| Age | Commit message (Collapse) | Author |
|---|
|
<srinivas.kandagatla@linaro.org>:
q6afe already exposes clocks using apis, but not as proper
clock controller driver. This patch puts those clocks
in to a proper clock controller so that other drivers that
depend on those clocks can be properly expressed.
Srinivas Kandagatla (2):
ASoC: q6afe: dt-bindings: add q6afe clock bindings
ASoC: q6afe-clocks: add q6afe clock controller
.../devicetree/bindings/sound/qcom,q6afe.txt | 23 ++
include/dt-bindings/sound/qcom,q6afe.h | 74 ++++-
sound/soc/qcom/Kconfig | 4 +
sound/soc/qcom/qdsp6/Makefile | 1 +
sound/soc/qcom/qdsp6/q6afe-clocks.c | 270 ++++++++++++++++++
5 files changed, 371 insertions(+), 1 deletion(-)
create mode 100644 sound/soc/qcom/qdsp6/q6afe-clocks.c
--
2.21.0
|
|
Ak4458 can't support DSD512 format, but ak4497 can, so add
a new enum variable (enum ak4458_type) in ak4458_drvdata to
distinguish these two platforms.
Ak4497 has two kinds of DSD input pin, it can be selected by
the dsd-path property from DT.
In hw_params(), bit clock is calculated according to different
DSD format (DSD64, DSD128, DSD256, DSD512), then registers
are configured.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1600178220-28973-2-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add "dsd-path" property, which is used for ak4497 codec
to select the DSD input pin.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1600178220-28973-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add a property to indicate if the device is to go into a High-z state on
the Tx ASI output pins when the device is idle.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200915190606.1744-3-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add code to allow the ASI Tx output to be placed into High-z mode
during unused ASI cycles. This allows for other devices that may be on
the bus to drive the ASI out. By default the 320adcx140 sends 0's for
unused cycles.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200915190606.1744-4-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The lpass-sc7180 driver can be built as a module but is lacking a
MODULE_DEVICE_TABLE. This means it won't auto-load. Fix this
oversight.
Fixes: 24caf8d9eb10 ("ASoC: qcom: lpass-sc7180: Add platform driver for lpass audio")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200916111545.1.I4c3758817d94c433bafeac344a395e21ea6657e3@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
SOF will support tgl-h and tgl-lp in different FW binaries due to
hardware difference, so create another dev_desc entry with FW name
of sof-tgl-h.ri and dsp_desc named tglh_chip_info for tgl-h.
Fixes: c8d2e2bfaeffa ("ASoC: SOF: Intel: add PCI IDs for ICL-H and TGL-H")
Signed-off-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200917103609.2559916-1-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
To avoid the actual PLL settings to differ from the state expected by
the clock driver, the codec should only be fully reset before the clocks
are registered. But we also need to ensure that the software reset
happens at all before clock registration, as not all boards have a reset
GPIO.
Move the software reset from aic32x4_component_probe() to
aic32x4_probe() and reorder the reset and registration sequence:
1. Reset via GPIO (if available)
2. Reset via software
3. Register component
4. Register clocks
Note that aic32x4_component_probe() is only called after aic32x4_probe()
has finished, so the reset in aic32x4_component_probe() was happening too
late.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20200902133043.19504-2-matthias.schiffer@ew.tq-group.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
error path
The regulators need to be disabled in the aic32x4_register_clocks()
failure case as well.
Fixes: 9d4befff5a95 ("ASoC: codec: tlv3204: Moving GPIO reset and add ADC reset")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20200902133043.19504-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
GPIO_ACTIVE_x flags are not correct in the context of interrupt flags.
These are simple defines so they could be used in DTS but they will not
have the same meaning:
1. GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE
2. GPIO_ACTIVE_LOW = 1 = IRQ_TYPE_EDGE_RISING
Correct the interrupt flags, assuming the author of the code wanted some
logical behavior behind the name "ACTIVE_xxx", this is:
ACTIVE_HIGH => IRQ_TYPE_LEVEL_HIGH
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200908145954.4629-1-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The common pattern for enumerating compatibles is enum, not oneOf.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200902160025.20922-1-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
SAI support select MCLK direction with version.major > 3
and version.minor > 1, the default direction is input,
set it to be output according to DT property.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/1600323079-5317-4-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
fsl_sai_check_version can help to parse the version info
in VERID and PARAM registers.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/1600323079-5317-3-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
On i.MX8MQ/i.MX8MN/i.MX8MM platform, the sai IP is upgraded.
There are some new registers and new bit definition. This
patch is to complete the register list.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/1600323079-5317-2-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
q6afe already exposes lpass clocks, however this was not presented
as proper clock controller driver. This patch basically adds clock
controller support for q6afe clocks.
This is useful for other drivers like lpass digital codec or lpass
lowpower island drivers to request or vote for these clocks.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200910135708.14842-3-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
q6afe exposes various lpass clocks controls via q6dsp q6afe commands.
This patch adds bindings required for this clock controller.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200910135708.14842-2-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Previous commits reduced the verbosity of errors during boot
iterations, but there are still a couple remaining which generate
false positives. Errors should only be logged when after last attempt
to download firmware failed.
Duplicating logs and assigning them different levels based on the
iteration number isn't really elegant, use macro as suggested by
Guennadi.
Suggested-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200917105633.2579047-9-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
On multiple locations checks are performed of untrusted values after adding
a constant to them. This is wrong, because the addition might overflow and
the result can then pass the check, although the original value is invalid.
Fix multiple such issues by checking the actual value and not a sum of it
and a constant.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200917105633.2579047-8-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
No need to type-cast assignments between void and other pointers in C.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200917105633.2579047-7-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In some cases no "ret" variable is even needed, those functions always
return 0 anyway, in other cases "ret" initialisation is redundant.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200917105633.2579047-6-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We need to avoid reporting an error for -EACCESS when pm_runtime is
not enabled.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200917105633.2579047-5-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We need to avoid reporting an error for -EACCESS when pm_runtime is
not enabled.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200917105633.2579047-4-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This field will be used to compare ldc file with loaded fw version,
to assert validity of trace logs. Value used in sof-logger.
Signed-off-by: Karol Trzcinski <karolx.trzcinski@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200917105633.2579047-3-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch adds debug support for imx platforms. This is important in
order to gather information about the state of the DSP in case of an
oops and the reason for the oops.
This is done by checking if a message with a panic code has been placed
in the debug box, in the imx8_dsp_handle_request function from sof/imx.
If positive, the function imx8_dump, added in common, will be called.
The first step is to gather information about the registers, filename,
line number and stack by calling the imx8_get_registers, added in common.
Then the information will be printed to the console by calling the
get_status function.
Signed-off-by: Iulian Olaru <iulianolaru249@yahoo.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200917105633.2579047-2-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fix the BCLK inversion for DSP modes
This is how it is defined by ASoC:
* BCLK:
* - "normal" polarity means signal is available at rising edge of BCLK
* - "inverted" polarity means signal is available at falling edge of BCLK
The adcx140 defines the BCLK edge based on coding type.
The PCM (DSP_A/B) should drive on rising and sample on falling edge, so
from ASoC pov, it is IB_NF. But from the codec pov if it is configured in
DSP mode, then the BCLK should not be inverted, defaults to the coding
standard.
For i2s, it is NB_NF from ASoC pov (drive on falling, sample on rising).
>From the codec's pov BCLK should not invert either, as this is the default
for the coding.
So, inversion must take the format into account:
IB_NF + DSP_A/B == the codec bclk inversion should be disabled
NB_NF + DSP_A/B == the codec bclk inversion should be enabled
NB_NF + I2S == the codec bclk inversion should be disabled
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200915190606.1744-2-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
It was observed that if the device was active and register writes were
performed there were some unwanted behaviors particularly when writing
the word length and some filter options. So when writing to the device
the device should be placed in sleep mode and then exit sleep mode once
the register update is complete.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200915190606.1744-1-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
According to its datasheet, the digital gain should be -100 dB when
CHx_DVOL is 1 and 27 dB when CHx_DVOL is 255. But with the current
dig_vol_tlv, "Digital CHx Out Volume" shows 27.5 dB if CHx_DVOL is 255
and -95.5 dB if CHx_DVOL is 1. This commit fixes this bug.
Fixes: 689c7655b50c ("ASoC: tlv320adcx140: Add the tlv320adcx140 codec driver family")
Signed-off-by: Camel Guo <camelg@axis.com>
Link: https://lore.kernel.org/r/20200908090417.16695-1-camel.guo@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When CONFIG_SND_CTL_VALIDATION is set, accesses to extended bytes
control generate spurious error messages when the size exceeds 512
bytes, such as
[ 11.224223] sof_sdw sof_sdw: control 2:0:0:EQIIR5.0 eqiir_coef_5:0:
invalid count 1024
In addition the error check returns -EINVAL which has the nasty side
effect of preventing applications accessing controls from working,
e.g.
root@plb:~# alsamixer
cannot load mixer controls: Invalid argument
It's agreed that the control interface has been abused since 2014, but
forcing a check should not prevent existing solutions from working.
This patch skips the checks conditionally if CONFIG_SND_CTL_VALIDATION
is set and the byte array provided by topology is > 512. This
preserves the checks for all other cases.
Fixes: 1a3232d2f61d2 ('ASoC: topology: Add support for TLV bytes controls')
BugLink: https://github.com/thesofproject/linux/issues/2430
Reported-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Jaska Uimonen <jaska.uimonen@intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200917103912.2565907-1-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
"alsactl -f state.conf store/restore" sequence fails because setting
"mixing clock source" and "output source" requires active TDM clock
being started for configuration propagation. Make these two controls
write only so that their values are not stored at "alsactl store".
Signed-off-by: Viorel Suman <viorel.suman@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Link: https://lore.kernel.org/r/1600104274-13110-1-git-send-email-viorel.suman@oss.nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fix the failure to flush DAC data before playback.
Signed-off-by: derek.fang <derek.fang@realtek.com>
Link: https://lore.kernel.org/r/1600073839-6762-2-git-send-email-derek.fang@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fix the DC calibration unsuccessful issue on rt1015
bypass boost mode.
Signed-off-by: derek.fang <derek.fang@realtek.com>
Link: https://lore.kernel.org/r/1600073839-6762-1-git-send-email-derek.fang@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"A collection of fixes I've been accruing over the last few weeks, none
of them have been severe enough to warrant flushing the queue but it's
been long enough now that it's a good idea to send them in.
A handful of them are fixups for QSPI DT/bindings/compatibles, some
smaller fixes for system DMA clock control and TMU interrupts on i.MX,
a handful of fixes for OMAP, including a fix for DSI (display) on
omap5"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (27 commits)
arm64: dts: ns2: Fixed QSPI compatible string
ARM: dts: BCM5301X: Fixed QSPI compatible string
ARM: dts: NSP: Fixed QSPI compatible string
ARM: dts: bcm: HR2: Fixed QSPI compatible string
dt-bindings: spi: Fix spi-bcm-qspi compatible ordering
ARM: dts: imx6sx: fix the pad QSPI1B_SCLK mux mode for uart3
arm64: dts: imx8mp: correct sdma1 clk setting
arm64: dts: imx8mq: Fix TMU interrupt property
ARM: dts: imx7d-zii-rmu2: fix rgmii phy-mode for ksz9031 phy
ARM: dts: vfxxx: Add syscon compatible with OCOTP
ARM: dts: imx6q-logicpd: Fix broken PWM
arm64: dts: imx: Add missing imx8mm-beacon-kit.dtb to build
ARM: dts: imx6q-prtwd2: Remove unneeded i2c unit name
ARM: dts: imx6qdl-gw51xx: Remove unneeded #address-cells/#size-cells
ARM: dts: imx7ulp: Correct gpio ranges
ARM: dts: ls1021a: fix QuadSPI-memory reg range
arm64: defconfig: Enable ptn5150 extcon driver
arm64: defconfig: Enable USB gadget with configfs
ARM: configs: Update Integrator defconfig
ARM: dts: omap5: Fix DSI base address and clocks
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/Thunderbolt fixes from Greg KH:
"Here are some small USB and Thunderbolt driver fixes for 5.9-rc5.
Nothing huge, just a number of bugfixes and new device ids for
problems reported:
- new USB serial driver ids
- bug fixes for syzbot reported problems
- typec driver fixes
- thunderbolt driver fixes
- revert of reported broken commit
All of these have been in linux-next with no reported issues"
* tag 'usb-5.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: typec: intel_pmc_mux: Do not configure SBU and HSL Orientation in Alternate modes
usb: typec: intel_pmc_mux: Do not configure Altmode HPD High
usb: core: fix slab-out-of-bounds Read in read_descriptors
Revert "usb: dwc3: meson-g12a: fix shared reset control use"
usb: typec: ucsi: acpi: Check the _DEP dependencies
usb: typec: intel_pmc_mux: Un-register the USB role switch
usb: Fix out of sync data toggle if a configured device is reconfigured
USB: serial: option: support dynamic Quectel USB compositions
USB: serial: option: add support for SIM7070/SIM7080/SIM7090 modules
thunderbolt: Use maximum USB3 link rate when reclaiming if link is not up
thunderbolt: Disable ports that are not implemented
USB: serial: ftdi_sio: add IDs for Xsens Mti USB converter
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO driver fixes from Greg KH:
"Here are a number of staging and IIO driver fixes for 5.9-rc5.
The majority of these are IIO driver fixes, to resolve a timestamp
issue that was recently found to affect a bunch of IIO drivers.
The other fixes in here are:
- small IIO driver fixes
- greybus driver fix
- counter driver fix (came in through the IIO fixes tree)
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-5.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (23 commits)
iio: adc: mcp3422: fix locking on error path
iio: adc: mcp3422: fix locking scope
iio: adc: meson-saradc: Use the parent device to look up the calib data
iio:adc:max1118 Fix alignment of timestamp and data leak issues
iio:adc:ina2xx Fix timestamp alignment issue.
iio:adc:ti-adc084s021 Fix alignment and data leak issues.
iio:adc:ti-adc081c Fix alignment and data leak issues
iio:magnetometer:ak8975 Fix alignment and data leak issues.
iio:light:ltr501 Fix timestamp alignment issue.
iio:light:max44000 Fix timestamp alignment and prevent data leak.
iio:chemical:ccs811: Fix timestamp alignment and prevent data leak.
iio:proximity:mb1232: Fix timestamp alignment and prevent data leak.
iio:accel:mma7455: Fix timestamp alignment and prevent data leak.
iio:accel:bmc150-accel: Fix timestamp alignment and prevent data leak.
iio:accel:mma8452: Fix timestamp alignment and prevent data leak.
iio: accel: kxsd9: Fix alignment of local buffer.
iio: adc: rockchip_saradc: select IIO_TRIGGERED_BUFFER
iio: adc: ti-ads1015: fix conversion when CONFIG_PM is not set
counter: microchip-tcb-capture: check the correct variable
iio: cros_ec: Set Gyroscope default frequency to 25Hz
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are some small driver core and debugfs fixes for 5.9-rc5
Included in here are:
- firmware loader memory leak fix
- firmware loader testing fixes for non-EFI systems
- device link locking fixes found by lockdep
- kobject_del() bugfix that has been affecting some callers
- debugfs minor fix
All of these have been in linux-next for a while with no reported
issues"
* tag 'driver-core-5.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
test_firmware: Test platform fw loading on non-EFI systems
PM: <linux/device.h>: fix @em_pd kernel-doc warning
kobject: Drop unneeded conditional in __kobject_del()
driver core: Fix device_pm_lock() locking for device links
MAINTAINERS: Add the security document to SECURITY CONTACT
driver code: print symbolic error code
debugfs: Fix module state check condition
kobject: Restore old behaviour of kobject_del(NULL)
firmware_loader: fix memory leak for paged buffer
|
|
https://github.com/Broadcom/stblinux into arm/fixes
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for
5.9, please pull the following:
- Florian fixes the Broadcom QSPI controller binding such that the most
specific compatible string is the left most one, and all existing
in-tree users are updated as well.
* tag 'arm-soc/for-5.9/devicetree-fixes' of https://github.com/Broadcom/stblinux:
arm64: dts: ns2: Fixed QSPI compatible string
ARM: dts: BCM5301X: Fixed QSPI compatible string
ARM: dts: NSP: Fixed QSPI compatible string
ARM: dts: bcm: HR2: Fixed QSPI compatible string
dt-bindings: spi: Fix spi-bcm-qspi compatible ordering
Link: https://lore.kernel.org/r/20200909211857.4144718-1-f.fainelli@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.9, round 2:
- Fix the misspelling of 'interrupts' property in i.MX8MQ TMU DT node.
- Correct 'ahb' clock for i.MX8MP SDMA1 in device tree.
- Fix pad QSPI1B_SCLK mux mode for UART3 on i.MX6SX.
* tag 'imx-fixes-5.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6sx: fix the pad QSPI1B_SCLK mux mode for uart3
arm64: dts: imx8mp: correct sdma1 clk setting
arm64: dts: imx8mq: Fix TMU interrupt property
Link: https://lore.kernel.org/r/20200909143844.GA25109@dragon
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omaps for v5.9-rc cycle
Few fixes for omap based devices:
- Fix of_clk_get() error handling for omap-iommu
- Fix missing audio pinctrl entries for logicpd boards
- Fix video for logicpd-som-lv after switch to generic panels
- Fix omap5 DSI clocks base
* tag 'omap-for-v5.9/fixes-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap5: Fix DSI base address and clocks
ARM: dts: logicpd-som-lv-baseboard: Fix missing video
ARM: dts: logicpd-som-lv-baseboard: Fix broken audio
ARM: dts: logicpd-torpedo-baseboard: Fix broken audio
ARM: OMAP2+: Fix an IS_ERR() vs NULL check in _get_pwrdm()
Link: https://lore.kernel.org/r/pull-1599132064-54898@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc driver fixes from Greg KH:
"Here are a number of small driver fixes for 5.9-rc5
Included in here are:
- habanalabs driver fixes
- interconnect driver fixes
- soundwire driver fixes
- dyndbg fixes for reported issues, and then reverts to fix it all up
to a sane state.
- phy driver fixes
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
Revert "dyndbg: accept query terms like file=bar and module=foo"
Revert "dyndbg: fix problem parsing format="foo bar""
scripts/tags.sh: exclude tools directory from tags generation
video: fbdev: fix OOB read in vga_8planes_imageblit()
dyndbg: fix problem parsing format="foo bar"
dyndbg: refine export, rename to dynamic_debug_exec_queries()
dyndbg: give %3u width in pr-format, cosmetic only
interconnect: qcom: Fix small BW votes being truncated to zero
soundwire: fix double free of dangling pointer
interconnect: Show bandwidth for disabled paths as zero in debugfs
habanalabs: fix report of RAZWI initiator coordinates
habanalabs: prevent user buff overflow
phy: omap-usb2-phy: disable PHY charger detect
phy: qcom-qmp: Use correct values for ipq8074 PCIe Gen2 PHY init
soundwire: bus: fix typo in comment on INTSTAT registers
phy: qualcomm: fix return value check in qcom_ipq806x_usb_phy_probe()
phy: qualcomm: fix platform_no_drv_owner.cocci warnings
|
|
Pull kvm fixes from Paolo Bonzini:
"A bit on the bigger side, mostly due to me being on vacation, then
busy, then on parental leave, but there's nothing worrisome.
ARM:
- Multiple stolen time fixes, with a new capability to match x86
- Fix for hugetlbfs mappings when PUD and PMD are the same level
- Fix for hugetlbfs mappings when PTE mappings are enforced (dirty
logging, for example)
- Fix tracing output of 64bit values
x86:
- nSVM state restore fixes
- Async page fault fixes
- Lots of small fixes everywhere"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (25 commits)
KVM: emulator: more strict rsm checks.
KVM: nSVM: more strict SMM checks when returning to nested guest
SVM: nSVM: setup nested msr permission bitmap on nested state load
SVM: nSVM: correctly restore GIF on vmexit from nesting after migration
x86/kvm: don't forget to ACK async PF IRQ
x86/kvm: properly use DEFINE_IDTENTRY_SYSVEC() macro
KVM: VMX: Don't freeze guest when event delivery causes an APIC-access exit
KVM: SVM: avoid emulation with stale next_rip
KVM: x86: always allow writing '0' to MSR_KVM_ASYNC_PF_EN
KVM: SVM: Periodically schedule when unregistering regions on destroy
KVM: MIPS: Change the definition of kvm type
kvm x86/mmu: use KVM_REQ_MMU_SYNC to sync when needed
KVM: nVMX: Fix the update value of nested load IA32_PERF_GLOBAL_CTRL control
KVM: fix memory leak in kvm_io_bus_unregister_dev()
KVM: Check the allocation of pv cpu mask
KVM: nVMX: Update VMCS02 when L2 PAE PDPTE updates detected
KVM: arm64: Update page shift if stage 2 block mapping not supported
KVM: arm64: Fix address truncation in traces
KVM: arm64: Do not try to map PUDs when they are folded into PMD
arm64/x86: KVM: Introduce steal-time cap
...
|
|
Pull OpenRISC fixes from Stafford Horne:
"Fixes for compile issues pointed out by kbuild and one bug I found in
initrd with the 5.9 patches"
* tag 'for-linus' of git://github.com/openrisc/linux:
openrisc: Fix issue with get_user for 64-bit values
openrisc: Fix cache API compile issue when not inlining
openrisc: Reserve memblock for initrd
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull seccomp fixes from Kees Cook:
"This fixes a rare race condition in seccomp when using TSYNC and
USER_NOTIF together where a memory allocation would not get freed
(found by syzkaller, fixed by Tycho).
Additionally updates Tycho's MAINTAINERS and .mailmap entries for his
new address"
* tag 'seccomp-v5.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
seccomp: don't leave dangling ->notif if file allocation fails
mailmap, MAINTAINERS: move to tycho.pizza
seccomp: don't leak memory when filter install races
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fix from Vishal Verma:
"Fix detection of dax support for block devices.
Previous fixes in this area, which only affected printing of debug
messages, had an incorrect condition for detection of dax. This fix
should finally do the right thing"
* tag 'libnvdimm-fix-v5.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
dax: fix detection of dax support for non-persistent memory block devices
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"A few more fixes:
- regression fix for a crash after failed snapshot creation
- one more lockep fix: use nofs allocation when allocating missing
device
- fix reloc tree leak on degraded mount
- make some extent buffer alignment checks less strict to mount
filesystems created by btrfs-convert"
* tag 'for-5.9-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: fix NULL pointer dereference after failure to create snapshot
btrfs: free data reloc tree on failed mount
btrfs: require only sector size alignment for parent eb bytenr
btrfs: fix lockdep splat in add_missing_dev
|
|
Pull cifs fix from Steve French:
"A fix for lookup on DFS link when cifsacl or modefromsid is used"
* tag '5.9-rc4-smb3-fix' of git://git.samba.org/sfrench/cifs-2.6:
cifs: fix DFS mount with cifsacl/modefromsid
|
|
Don't ignore return values in rsm_load_state_64/32 to avoid
loading invalid state from SMM state area if it was tampered with
by the guest.
This is primarly intended to avoid letting guest set bits in EFER
(like EFER.SVME when nesting is disabled) by manipulating SMM save area.
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20200827171145.374620-8-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
* check that guest is 64 bit guest, otherwise the SVM related fields
in the smm state area are not defined
* If the SMM area indicates that SMM interrupted a running guest,
check that EFER.SVME which is also saved in this area is set, otherwise
the guest might have tampered with SMM save area, and so indicate
emulation failure which should triple fault the guest.
* Check that that guest CPUID supports SVM (due to the same issue as above)
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20200827162720.278690-4-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
This code was missing and was forcing the L2 run with L1's msr
permission bitmap
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20200827162720.278690-3-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
