| Age | Commit message (Collapse) | Author |
|---|
|
based hardcoding
Use OMAP_HSMMC_SUPPORTS_DUAL_VOLT flag instead of host->id
for identifying SD bus voltage capabilities.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
set_sleep seems to be unused in omap_hsmmc driver. so get rid of it.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Git rid of hardcoded tx/rx DMA channels based on pdev->id
and use platform_get_resource_byname() to retrieve them
instead.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
To prevent I/O as soon as possible at card removal, a new detect work is
re-scheduled without a delay to let a rescan remove the card device as
soon as possible.
Additionally, MMC_CAP2_DETECT_ON_ERR can now be used to handle "slowly"
removed cards that a scheduled detect work did not detect as removed.
To prevent further I/O requests for these lingering removed cards,
check if card has been removed and then schedule a detect work to
properly remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
3ec7699d3bb1b0ee7 ("mmc: dw_mmc: Add support for pre_req and post_req")
broke non-IDMAC DMA, because dw_mci_pre_dma_transfer() is valid only if
using internal DMA. In case of using other DMA it returns -ENOSYS. It
prevents the DMA operations. This patch makes dw_mci_pre_dma_transfer()
effective in all DMA cases again.
Reported-by: James Hogan <james@albanarts.com>
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
When disable CONFIG_MMC_DW_IDMAC, can see the compiler error.
Because in dw_mci_post_req(), called the dw_mci_get_dma_dir().
But that function is in #ifdef CONFIG_MMC_DW_IDMAC.
I think that function is generic function.
Not need the CONFIG_MMC_DW_IDMAC.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
External circuitry like level shifters may limit the maximum operation
speed of the hsmmc controller. Add a field to struct omap2_hsmmc_info
so boards can adjust the setting on demand.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
commit 6bd081277ea0 "dmaengine: imx-dma: merge old dma-v1.c with
imx-dma.c" removed the dependency in config for the imx dma driver,
whereas it should depend on ARCH_MXS
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
If relocate of block group 0 fails with ENOSPC we end up infinitely
looping because key.offset -= 1 statement in that case brings us back to
where we started.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
init_ipath() allocates btrfs_data_container which is never freed. Free
it in free_ipath() and nuke the comment for init_data_container() - we
can safely free it with kfree().
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
Generally we don't allow dup for data, but mixed chunks are special and
people seem to think this has its use cases.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
Do not run sanity checks on all target profiles unless they all will be
used. This came up because alloc_profile_is_valid() is now more strict
than it used to be.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
Currently if we don't have enough space allocated we go ahead and loop
though devices in the hopes of finding enough space for a chunk of the
*same* type as the one we are trying to relocate. The problem with that
is that if we are trying to restripe the chunk its target type can be
more relaxed than the current one (eg require less devices or less
space). So, when restriping, run checks against the target profile
instead of the current one.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
Add __get_block_group_index() helper to be able to derive block group
index from an arbitary set of flags. Implement get_block_group_index()
in terms of it.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
Add get_restripe_target() helper and switch everybody to use it.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
Header file is not a good place to define functions. This also moves a
call to alloc_profile_is_valid() down the stack and removes a redundant
check from __btrfs_alloc_chunk() - alloc_profile_is_valid() takes it
into account.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
"0" is a valid value for an on-disk chunk profile, but it is not a valid
extended profile. (We have a separate bit for single chunks in extended
case)
Also rename it to alloc_profile_is_valid() for clarity.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
Add functions to abstract the conversion between chunk and extended
allocation profile formats and switch everybody to use them.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
This has been causing a lot of confusion for quite a while now and a lot
of users were surprised by this (some of them were even stuck in a
ENOSPC situation which they couldn't easily get out of). The addition
of restriper gives users a clear choice between raid0 and drive concat
setup so there's absolutely no excuse for us to keep doing this.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
Fix failure in aa_change_onexec api when the request is made from a confined
task. This failure was caused by two problems
The AA_MAY_ONEXEC perm was not being mapped correctly for this case.
The executable name was being checked as second time instead of using the
requested onexec profile name, which may not be the same as the exec
profile name. This mistake can not be exploited to grant extra permission
because of the above flaw where the ONEXEC permission was not being mapped
so it will not be granted.
BugLink: http://bugs.launchpad.net/bugs/963756
Signed-off-by: John Johansen <john.johansen@canonical.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
|
|
commit 74a622b (ia64: vsyscall: Use seqcount instead of seqlock) broke
the ia64 build.
Reported-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Avoid extra work by continuing on to the next rt_rq if the highest
prio task in current rt_rq is the same priority as our candidate
task.
More detailed explanation: if next is not NULL, then we have found a
candidate task, and its priority is next->prio. Now we are looking
for an even higher priority task in the other rt_rq's. idx is the
highest priority in the current candidate rt_rq. In the current 3.3
code, if idx is equal to next->prio, we would start scanning the tasks
in that rt_rq and replace the current candidate task with a task from
that rt_rq. But the new task would only have a priority that is equal
to our previous candidate task, so we have not advanced our goal of
finding a higher prio task. So we should avoid the extra work by
continuing on to the next rt_rq if idx is equal to next->prio.
Signed-off-by: Michael J Wang <mjwang@broadcom.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Reviewed-by: Yong Zhang <yong.zhang0@gmail.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/2EF88150C0EF2C43A218742ED384C1BC0FC83D6B@IRVEXCHMB08.corp.ad.broadcom.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
In commit 4692cf58 we introduced new backref walking code for btrfs. This
assumes we're searching live roots, which requires a transaction context.
While scrubbing, however, we must not join a transaction because this could
deadlock with the commit path. Additionally, what scrub really wants to do
is resolving a logical address in the commit root it's currently checking.
This patch adds support for logical to path resolving on commit roots and
makes scrub use that.
Signed-off-by: Jan Schmidt <list.btrfs@jan-o-sch.net>
|
|
The two helper functions commit_cowonly_roots() and
create_pending_snapshot() failed to check the return value from
btrfs_cow_block(), which could at least in theory fail with -ENOSPC from
btrfs_alloc_free_block(). This commit adds the missing checks.
Signed-off-by: Jan Schmidt <list.btrfs@jan-o-sch.net>
|
|
btrfs_init_lockdep only makes our lockdep class names look prettier, thus
it did never hurt we forgot to actually call it. This turns our lockdep
identifier strings from lockdep auto-set #[id] into really pretty
"btrfs-fs-01" or "btrfs-csum-03".
Signed-off-by: Jan Schmidt <list.btrfs@jan-o-sch.net>
|
|
Commit 5fbd036b55 ("sched: Cleanup cpu_active madness"), which was
supposed to finally sort the cpu_active mess, instead uncovered more.
Since CPU_STARTING is ran before setting the cpu online, there's a
(small) window where the cpu has active,!online.
If during this time there's a wakeup of a task that used to reside on
that cpu select_task_rq() will use select_fallback_rq() to compute an
alternative cpu to run on since we find !online.
select_fallback_rq() however will compute the new cpu against
cpu_active, this means that it can return the same cpu it started out
with, the !online one, since that cpu is in fact marked active.
This results in us trying to scheduling a task on an offline cpu and
triggering a WARN in the IPI code.
The solution proposed by Chuansheng Liu of setting cpu_active in
set_cpu_online() is buggy, firstly not all archs actually use
set_cpu_online(), secondly, not all archs call set_cpu_online() with
IRQs disabled, this means we would introduce either the same race or
the race from fd8a7de17 ("x86: cpu-hotplug: Prevent softirq wakeup on
wrong CPU") -- albeit much narrower.
[ By setting online first and active later we have a window of
online,!active, fresh and bound kthreads have task_cpu() of 0 and
since cpu0 isn't in tsk_cpus_allowed() we end up in
select_fallback_rq() which excludes !active, resulting in a reset
of ->cpus_allowed and the thread running all over the place. ]
The solution is to re-work select_fallback_rq() to require active
_and_ online. This makes the active,!online case work as expected,
OTOH archs running CPU_STARTING after setting online are now
vulnerable to the issue from fd8a7de17 -- these are alpha and
blackfin.
Reported-by: Chuansheng Liu <chuansheng.liu@intel.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: linux-alpha@vger.kernel.org
Link: http://lkml.kernel.org/n/tip-hubqk1i10o4dpvlm06gq7v6j@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
We should not ever enable IRQs until we're fully set up. This opens up
a window where interrupts can hit the cpu and interrupts can do
wakeups, wakeups need state that isn't set-up yet, in particular this
cpu isn't elegible to run tasks, so if any cpu-affine task that got
created in CPU_UP_PREPARE manages to get a wakeup, its affinity mask
will get broken and we'll run into lots of 'interesting' problems.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/n/tip-yaezmlbriluh166tfkgni22m@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Conflicts:
arch/arm/Kconfig.debug
arch/arm/plat-versatile/Kconfig
Merge fixes:
arch/arm/mach-integrator/Kconfig
drivers/clocksource/Kconfig
|
|
|
|
Last night's randconfig and the allnoconfig builds spat out the
following warning while building:
warning: (ARM) selects HAVE_BPF_JIT which has unmet direct dependencies (NET)
Acked-by: Mircea Gherzan <mgherzan@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Conflicts:
drivers/input/tablet/wacom_sys.c
|
|
Following commit broke DT support for tegra-kbc by removing pdata
allocation completely:
commit 023cea0ecfa2df034096c3f4afa796a0b2d1188a
Author: Shridhar Rasal <srasal@nvidia.com>
Date: Fri Feb 3 00:27:30 2012 -0800
Input: tegra-kbc - allow skipping setting up some of GPIO pins
This patch restores it.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
|
|
Since we need to read and write extent buffers in their entirety we can't use
the normal bio_readpage_error stuff since it only works on a per page basis. So
instead make it so that if we see an io error in endio we just mark the eb as
having an IO error and then in btree_read_extent_buffer_pages we will manually
try other mirrors and then overwrite the bad mirror if we find a good copy.
This works with larger than page size blocks. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
|
|
Move linux specific module parameter gts and bfs out of ACPICA core
code to sleep.c.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Enhanced the sleep/wake interfaces to optionally execute the
_GTS method (Going To Sleep), and the _BFS method (Back From
Sleep). Windows apparently does not execute these methods, and
therefore these methods are often untested. It has been seen on
some systems where the execution of these methods causes errors
and also prevents the machine from entering S5. It is therefore
suggested that host operating systems do not execute these methods
by default. In the future, perhaps these methods can be optionally
executed based on the age of the system and/or what is the newest
version of Windows that the BIOS asks for via _OSI.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
As docg3 is intolerant against reentrancy, especially
because of its weird register access (ie. a register read is
performed by a first register write), each access to the
docg3 IO space must be locked.
Lock the IO space with a mutex, shared by all chips on the
same cascade, as they all share the same IO space.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Group floors into a common cascade structure. This will provide a common
structure to store common data to all cascaded docg3 chips, like IO
addressing, locking protection.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
After several tries with ubifs, it appears empirically that constructor
provided figures for erase/write timeouts are underestimated. A timeout
of 100ms seems to work with a 5 years worn chip, and no timeouts occur
anymore.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
The last erase block was not accessible, as the out of bound
check was incorrectly rejecting the last block.
The read/write/erase offset checks were forbidding the usage of the
last block, because of the calculation which was considering the
byte after the last instead of the last byte.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
A lot of functions have been marked __devinit, but they shouldn't, because they
are needed for bbt_scan. While I believe the whole MX23 handling should be done
entirely different, I am missing the resources to fix it. So, let's have at least
the annotations correct.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
phram_setup() is only called from init_phram() which is in .init.text,
so it must be in the same section to avoid a section mismatch warning.
Signed-off-by: Ryosuke Saito <raitosyo@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Initialization of 'erase_info->fail_addr' to MTD_FAIL_ADDR_UNKNOWN prior
erase operation is duplicated accross several MTD drivers, and also taken
care of by some MTD users as well.
Harmonize it: initialize 'fail_addr' within 'mtd_erase()' interface.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
With onfi a flash is organized into one or more logical units (LUNs).
A logical unit (LUN) is the minimum unit that can independently execute
commands and report status.
Mtd does not exploit LUN, so make it see a big single flash where size is
lun_size * number_of_lun.
Without this patch MT29F8G08ADBDAH4 size is 512MiB instead of 1GiB.
Artem: split long line on 2 shorter ones.
Signed-off-by: Matthieu Castet <matthieu.castet@parrot.com>
Acked-by: Florian Fainelli <ffainelli@freebox.fr>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
major == 0 allocates dynamic major, not major == -1
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
This patch adds support to configure the SPEAr SMI driver via
device-tree instead of platform_data.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Additionally, after failing in mtd_device_parse_register(), the driver
unmap/free code is now executed.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
This patch adds support to configure the FSMC NAND driver (used amongst
others on SPEAr platforms) via device-tree instead of platform_data.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
doc_probe_device() is only called from docg3_probe() which is in .init.text,
so it must be in the same section to avoid a section mismatch warning.
Signed-off-by: Ryosuke Saito <raitosyo@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
