| Age | Commit message (Collapse) | Author |
|---|
|
The MMP2 platform, that uses device tree, has this controller. Let's add
devicetree alongside platform & PCI.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
That seems to be the correct type.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This driver supports GENI based SPI Controller in the Qualcomm SOCs. The
Qualcomm Generic Interface (GENI) is a programmable module supporting a
wide range of serial interfaces including SPI. This driver supports SPI
operations using FIFO mode of transfer.
Signed-off-by: Girish Mahadevan <girishm@codeaurora.org>
Signed-off-by: Dilip Kota <dkota@codeaurora.org>
Signed-off-by: Alok Chauhan <alokc@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Move GENI SE SPI controller device-tree bindings
from devicetree/bindings/soc/qcom/qcom,geni-se.txt
to devicetree/bindings/spi/qcom,spi-geni-qcom.txt.
Signed-off-by: Dilip Kota <dkota@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alok Chauhan <alokc@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
SPI controller driver should maintain the maximum frequency
of the controller instead of relying on device tree bindings.
Because maximum frequency is specific property of SPI
controller.
Signed-off-by: Dilip Kota <dkota@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alok Chauhan <alokc@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Let the dma/non-dma code paths handle the spi enable
flag themselves. This removes some logic to determine
if the flag should be turned on before or after dma
and also don't leave the spi enabled if the dma path
fails.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The dma direction for the tx and rx dma channels never
change, so just use the constants directly rather
than storing them in device data.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The driver data has a u32 field use_dma which is
only ever used as a boolean, so change its type
to reflect that.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We no longer need the dma_caps since the dma driver
already clamps the burst length to the hardware limit,
so don't request and store dma_caps in device data.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Signal tx dma when spi fifo is less than half full,
and limit tx bursts to half the fifo length.
Clamp rx burst length to 1 to avoid alignment issues.
Signed-off-by: Huibin Hong <huibin.hong@rock-chips.com>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Michael reported that he could not stat following event:
$ perf stat -e unc_p_freq_ge_1200mhz_cycles -a -- ls
event syntax error: '..e_1200mhz_cycles'
\___ value too big for format, maximum is 255
Run 'perf list' for a list of valid events
The event is unwrapped into:
uncore_pcu/event=0xb,filter_band0=1200/
where filter_band0 format says it's one byte only:
# cat uncore_pcu/format/filter_band0
config1:0-7
while JSON files specifies bigger number:
"Filter": "filter_band0=1200",
all the filter_band* formats show 1 byte width:
# cat uncore_pcu/format/filter_band1
config1:8-15
# cat uncore_pcu/format/filter_band2
config1:16-23
# cat uncore_pcu/format/filter_band3
config1:24-31
The reason of the issue is that filter_band* values are supposed to be
in 100Mhz units.. it's stated in the JSON help for the events, like:
filter_band3=XXX, with XXX in 100Mhz units
This patch divides the filter_band* values by 100, plus there's couple
of changes that actually change the number completely, like:
- "Filter": "edge=1,filter_band2=4000",
+ "Filter": "edge=1,filter_band2=30",
Reported-by: Michael Petlan <mpetlan@redhat.com>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Acked-by: Andi Kleen <ak@linux.intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20181010080339.GB15790@krava
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
The rxconf and txconf structs are allocated on the
stack, so make sure we zero them before filling out
the relevant fields.
Signed-off-by: Huibin Hong <huibin.hong@rock-chips.com>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
New driver for Qualcomm QuadSPI(QSPI) controller that is used to
communicate with slaves such as flash memory devices. The QSPI controller
can operate in 2 or 4 wire mode but only supports SPI Mode 0. The
controller can also operate in Single or Dual data rate modes.
Signed-off-by: Girish Mahadevan <girishm@codeaurora.org>
Signed-off-by: Ryan Case <ryandcase@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Bindings for Qualcomm Quad SPI used on SoCs such as sdm845.
Signed-off-by: Girish Mahadevan <girishm@codeaurora.org>
Signed-off-by: Ryan Case <ryandcase@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add support for a new devicetree compatible string called
'amazon,alpine-apb-ssi', which is necessary for the Amazon Alpine spi
controller. 'amazon,alpine-dw-apb-ssi' is used in the dw spi driver if
specified in the devicetree. Otherwise, fall back to driver default
behavior, i.e. original dw IP hw driver behavior.
Signed-off-by: Talel Shenhar <talel@amazon.com>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This compatible adds the ability for dw spi controller driver to work with
the dw spi controller found on Alpine chips.
The dw spi controller has an auto-deselect of Chip-Select, in case there is
no data inside the Tx FIFO. While working on platforms with Alpine chips,
auto-deselect mode causes an issue for some spi devices that can't handle
the Chip-Select deselect in the middle of a transaction. It is a normal
behavior for a Tx FIFO to be empty in the middle of a transaction, due to
busy cpu. In the Alpine chip family an option to change the default
behavior was added to the original dw spi controller to prevent this issue
of de-asserting Chip-Select once TX FIFO is empty. The change was to allow
SW manual control of the Chip-Select. With this change, as long as the
Slave Enable Register is asserted, the Chip-Select will be asserted. As a
result, it is necessary to deselect the Slave Select Register once the
transaction is done. This feature is enabled via a new device compatible
string called 'amazon,alpine-dw-apb-ssi'. Once the driver identifies the
new compatible string, it enables the hw fixup logic, by writing to a
dedicated register found in the IP reserved area and will start manual
deselecting the Slave Select Register when the transfer ends.
Signed-off-by: Talel Shenhar <talel@amazon.com>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into spi-4.20
Immutable branch for QCOM Geni patches
|
|
Previous implementation of SAE authentication in infrastructure BSS was
somewhat restricting and not exactly clean way of handling the two
auth() operations. This ended up removing and re-adding the STA entry
for the AP in the middle of authentication and also messing up
authentication state tracking through the sequence of four
Authentication frames. Furthermore, this did not work if the AP ended up
sending out SAE Confirm (auth trans #2) immediately after SAE Commit
(auth trans #1) before the station had time to transmit its SAE Confirm.
Clean up authentication state handling for the SAE case to allow two
rounds of auth() calls without dropping all state between those
operations. Track peer Confirmed status and mark authentication
completed only once both ends have confirmed.
ieee80211_mgd_auth() check for EBUSY cases is now handling only the
pending association (ifmgd->assoc_data) while all pending authentication
(ifmgd->auth_data) cases are allowed to proceed to allow user space to
start a new connection attempt from scratch even if the previously
requested authentication is still waiting completion. This is needed to
avoid making SAE error cases with retries take excessive amount of time
with no means for the user space to stop that (apart from setting the
netdev down).
As an extra bonus, the end of ieee80211_rx_mgmt_auth() can be cleaned up
to avoid the extra copy of the cfg80211_rx_mlme_mgmt() call for ongoing
SAE authentication since the new ieee80211_mark_sta_auth() helper
function can handle both completion of authentication and updates to the
STA entry under the same condition and there is no need to return from
the function between those operations.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This makes it easier to conditionally replace full allocation of
auth_data to use reallocation for the case of continuing SAE
authentication. Furthermore, there was not really any point in having
this check done so late in the function after having already completed
number of steps that cannot be used anyway in the error case.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Authentication exchange can be completed in both TX and RX paths for
SAE, so move this common functionality into a helper function to avoid
having to implement practically the same operations in two places when
extending SAE implementation in the following commits.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When there are few packets (e.g. for sampling attempts), the exponentially
weighted variance is usually vastly overestimated, making the resulting data
essentially useless. As far as I know, there has not been any practical use
for this, so let's not waste any cycles on it.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
These rates are highly unlikely to be used quickly, even if the link
deteriorates rapidly. This improves throughput in cases where CCK rates
are not reliable enough to be skipped entirely during sampling.
Sampling these rates regularly can cost a lot of airtime.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Long/short preamble selection cannot be sampled separately, since it
depends on the BSS state. Because of that, sampling attempts to
currently not used preamble modes are not counted in the statistics,
which leads to CCK rates being sampled too often.
Fix statistics accounting for long/short preamble by increasing the
index where necessary.
Fix excessive CCK rate sampling by dropping unsupported sample attempts.
This improves throughput on 2.4 GHz channels
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Fixes a harmless underflow issue when CCK rates are actively being used
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
mi->supported[MINSTREL_CCK_GROUP] needs to be updated
short preamble rates need to be marked as supported regardless of
whether it's currently enabled. Its state can change at any time without
a rate_update call.
Fixes: 782dda00ab8e ("mac80211: minstrel_ht: move short preamble check out of get_rate")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
By storing a shift value for all duration values of a group, we can
reduce precision by a neglegible amount to make it fit into a u16 value.
This improves cache footprint and reduces size:
Before:
text data bss dec hex filename
10024 116 0 10140 279c rc80211_minstrel_ht.o
After:
text data bss dec hex filename
9368 116 0 9484 250c rc80211_minstrel_ht.o
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Legacy-only devices are not very common and the overhead of the extra
code for HT and VHT rates is not big enough to justify all those extra
lines of code to make it optional.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
debugfs entries are cleaned up by debugfs_remove_recursive already.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If peer support reception of STBC and LDPC, enable them for better
performance.
Signed-off-by: Chaitanya TK <chaitanya.mgit@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
I'm not really sure exactly _why_ I've been carrying a note
for what's probably _years_ to check that we don't do this,
but we clearly do reflect frames back to the station itself
if it sends such.
One way or the other, it's useless since the station doesn't
really need the AP to talk to itself, so suppress it.
While at it, clarify some of the logic by removing skb->data
references in favour of the destination address (pointer) we
already have separately.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Instead of open-coding a lot of calls to is_valid_ie_attr(),
add this validation directly to the policy, now that we can.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Many range checks can be done in the policy, move them
there. A few in mesh are added in the code (taken out of
the macros) because they don't fit into the s16 range in
the policy validation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Fixing/optimizing bcm_qspi_bspi_read() performance introduced two
changes:
1) It added a loop to read all requested data using multiple BSPI ops.
2) It bumped max size of a single BSPI block request from 256 to 512 B.
The later change resulted in occasional BSPI timeouts causing a
regression.
For some unknown reason hardware doesn't always handle reads as expected
when using 512 B chunks. In such cases it may happen that BSPI returns
amount of requested bytes without the last 1-3 ones. It provides the
remaining bytes later but doesn't raise an interrupt until another LR
start.
Switching back to 256 B reads fixes that problem and regression.
Fixes: 345309fa7c0c ("spi: bcm-qspi: Fix bcm_qspi_bspi_read() performance")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
|
|
During implementation of the new API bcm_qspi_bspi_set_flex_mode() has
been modified breaking calculation of address length. An unnecessary
multiplication was added breaking flash reads.
Fixes: 5f195ee7d830 ("spi: bcm-qspi: Implement the spi_mem interface")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
|
|
The DTK-2451 and DTH-2452 have a buggy HID descriptor which incorrectly
contains a Cintiq-like report, complete with pen tilt, rotation, twist, serial
number, etc. The hardware doesn't actually support this data but our driver
duitifully sets up the device as though it does. To ensure userspace has a
correct view of devices without updated firmware, we clean up this incorrect
data in wacom_setup_device_quirks.
We're also careful to clear the WACOM_QUIRK_TOOLSERIAL flag since its presence
causes the driver to wait for serial number information (via
wacom_wac_pen_serial_enforce) that never comes, resulting in
the pen being non-responsive.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Fixes: 8341720642 ("HID: wacom: Queue events with missing type/serial data for later processing")
Cc: stable@vger.kernel.org # v4.16+
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
bydst table/list lookups use rcu, so insertions must use rcu versions.
Fixes: a7c44247f704e ("xfrm: policy: make xfrm_policy_lookup_bytype lockless")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
BUG: KASAN: slab-out-of-bounds in _decode_session6+0x1331/0x14e0
net/ipv6/xfrm6_policy.c:161
Read of size 1 at addr ffff8801d882eec7 by task syz-executor1/6667
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x1c9/0x2b4 lib/dump_stack.c:113
print_address_description+0x6c/0x20b mm/kasan/report.c:256
kasan_report_error mm/kasan/report.c:354 [inline]
kasan_report.cold.7+0x242/0x30d mm/kasan/report.c:412
__asan_report_load1_noabort+0x14/0x20 mm/kasan/report.c:430
_decode_session6+0x1331/0x14e0 net/ipv6/xfrm6_policy.c:161
__xfrm_decode_session+0x71/0x140 net/xfrm/xfrm_policy.c:2299
xfrm_decode_session include/net/xfrm.h:1232 [inline]
vti6_tnl_xmit+0x3c3/0x1bc1 net/ipv6/ip6_vti.c:542
__netdev_start_xmit include/linux/netdevice.h:4313 [inline]
netdev_start_xmit include/linux/netdevice.h:4322 [inline]
xmit_one net/core/dev.c:3217 [inline]
dev_hard_start_xmit+0x272/0xc10 net/core/dev.c:3233
__dev_queue_xmit+0x2ab2/0x3870 net/core/dev.c:3803
dev_queue_xmit+0x17/0x20 net/core/dev.c:3836
Reported-by: syzbot+acffccec848dc13fe459@syzkaller.appspotmail.com
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
With a very low cpu.cfs_quota_us setting, such as the minimum of 1000,
distribute_cfs_runtime may not empty the throttled_list before it runs
out of runtime to distribute. In that case, due to the change from
c06f04c7048 to put throttled entries at the head of the list, later entries
on the list will starve. Essentially, the same X processes will get pulled
off the list, given CPU time and then, when expired, get put back on the
head of the list where distribute_cfs_runtime will give runtime to the same
set of processes leaving the rest.
Fix the issue by setting a bit in struct cfs_bandwidth when
distribute_cfs_runtime is running, so that the code in throttle_cfs_rq can
decide to put the throttled entry on the tail or the head of the list. The
bit is set/cleared by the callers of distribute_cfs_runtime while they hold
cfs_bandwidth->lock.
This is easy to reproduce with a handful of CPU consumers. I use 'crash' on
the live system. In some cases you can simply look at the throttled list and
see the later entries are not changing:
crash> list cfs_rq.throttled_list -H 0xffff90b54f6ade40 -s cfs_rq.runtime_remaining | paste - - | awk '{print $1" "$4}' | pr -t -n3
1 ffff90b56cb2d200 -976050
2 ffff90b56cb2cc00 -484925
3 ffff90b56cb2bc00 -658814
4 ffff90b56cb2ba00 -275365
5 ffff90b166a45600 -135138
6 ffff90b56cb2da00 -282505
7 ffff90b56cb2e000 -148065
8 ffff90b56cb2fa00 -872591
9 ffff90b56cb2c000 -84687
10 ffff90b56cb2f000 -87237
11 ffff90b166a40a00 -164582
crash> list cfs_rq.throttled_list -H 0xffff90b54f6ade40 -s cfs_rq.runtime_remaining | paste - - | awk '{print $1" "$4}' | pr -t -n3
1 ffff90b56cb2d200 -994147
2 ffff90b56cb2cc00 -306051
3 ffff90b56cb2bc00 -961321
4 ffff90b56cb2ba00 -24490
5 ffff90b166a45600 -135138
6 ffff90b56cb2da00 -282505
7 ffff90b56cb2e000 -148065
8 ffff90b56cb2fa00 -872591
9 ffff90b56cb2c000 -84687
10 ffff90b56cb2f000 -87237
11 ffff90b166a40a00 -164582
Sometimes it is easier to see by finding a process getting starved and looking
at the sched_info:
crash> task ffff8eb765994500 sched_info
PID: 7800 TASK: ffff8eb765994500 CPU: 16 COMMAND: "cputest"
sched_info = {
pcount = 8,
run_delay = 697094208,
last_arrival = 240260125039,
last_queued = 240260327513
},
crash> task ffff8eb765994500 sched_info
PID: 7800 TASK: ffff8eb765994500 CPU: 16 COMMAND: "cputest"
sched_info = {
pcount = 8,
run_delay = 697094208,
last_arrival = 240260125039,
last_queued = 240260327513
},
Signed-off-by: Phil Auld <pauld@redhat.com>
Reviewed-by: Ben Segall <bsegall@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Fixes: c06f04c70489 ("sched: Fix potential near-infinite distribute_cfs_runtime() loop")
Link: http://lkml.kernel.org/r/20181008143639.GA4019@pauld.bos.csb
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Ingo writes:
"x86 fixes
An intel_rdt memory access fix and a VLA fix in pgd_alloc()."
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Avoid VLA in pgd_alloc()
x86/intel_rdt: Fix out-of-bounds memory access in CBM tests
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Ingo writes:
"scheduler fix:
Cleanup of dead code left over from the recent sched/numa fixes."
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
mm, sched/numa: Remove remaining traces of NUMA rate-limiting
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Ingo, a man of few words, writes:
"perf fixes:
misc perf tooling fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf record: Use unmapped IP for inline callchain cursors
perf python: Use -Wno-redundant-decls to build with PYTHON=python3
perf report: Don't try to map ip to invalid map
perf script python: Fix export-to-sqlite.py sample columns
perf script python: Fix export-to-postgresql.py occasional failure
|
|
Zero pad private area, otherwise we expose private kernel pointer to
userspace. This patch also zeroes the tail area after the ->matchsize
and ->targetsize that results from XT_ALIGN().
Fixes: 0ca743a55991 ("netfilter: nf_tables: add compatibility layer for x_tables")
Reported-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
checkentry(tee_tg_check) should initialize priv->oif from dev if possible.
But only netdevice notifier handler can set that.
Hence priv->oif is always -1 until notifier handler is called.
Fixes: 9e2f6c5d78db ("netfilter: Rework xt_TEE netdevice notifier")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
TEE netdevice notifier handler checks only interface name. however
each netns can have same interface name. hence other netns's interface
could be selected.
test commands:
%ip netns add vm1
%iptables -I INPUT -p icmp -j TEE --gateway 192.168.1.1 --oif enp2s0
%ip link set enp2s0 netns vm1
Above rule is in the root netns. but that rule could get enp2s0
ifindex of vm1 by notifier handler.
After this patch, TEE rule is added to the per-netns list.
Fixes: 9e2f6c5d78db ("netfilter: Rework xt_TEE netdevice notifier")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
The nft_osf extension, like xt_osf, is not supported from the output
path.
Fixes: b96af92d6eaf ("netfilter: nf_tables: implement Passive OS fingerprint module in nft_osf")
Signed-off-by: Fernando Fernandez Mancera <ffmancera@riseup.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Allow to find closest matching for the right side of an interval (end
flag set on) so we allow lookups in inner ranges, eg. 10-20 in 5-25.
Fixes: ba0e4d9917b4 ("netfilter: nf_tables: get set elements via netlink")
Reported-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Refresh the document:
- Remove unnecessary liguistic complexity and improve the clarity of the text
- Improve the explanations all around
- Remove unnecessary and stale version info
- Fix whitespace noise
- Make pseudo-code match kernel style
- Fix minor syntax errors in pseudo-code
- Use consistent denotation
- Mark multi-CPU sequences more explicitly
- Unbreak line breaks
- Use quotes to refer to 'struct completion'
- Use 'IRQ context' and 'IRQs' consistently
- Improve grammar
- etc.
Cc: John Garry <john.garry@huawei.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Nicholas Mc Guire <hofrat@osadl.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: corbet@lwn.net
Cc: linux-doc@vger.kernel.org
Link: http://lkml.kernel.org/r/1539183392-239389-1-git-send-email-john.garry@huawei.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
This patch fixes a couple of punctuation nits which can make the document
more correct and readable.
Also missing "()" are added to some function references for consistency.
Signed-off-by: John Garry <john.garry@huawei.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: corbet@lwn.net
Cc: linux-doc@vger.kernel.org
Link: http://lkml.kernel.org/r/1539183392-239389-1-git-send-email-john.garry@huawei.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
When test_flow_dissector.sh runs it complains that it can't find script
with_addr.sh:
./test_flow_dissector.sh: line 81: ./with_addr.sh: No such file or
directory
Rework so that with_addr.sh gets installed, add it to
TEST_PROGS_EXTENDED variable.
Fixes: 50b3ed57dee9 ("selftests/bpf: test bpf flow dissection")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
When test_lwt_seg6local.sh was added commit c99a84eac026
("selftests/bpf: test for seg6local End.BPF action") config fragment
wasn't added, and without CONFIG_LWTUNNEL enabled we see this:
Error: CONFIG_LWTUNNEL is not enabled in this kernel.
selftests: test_lwt_seg6local [FAILED]
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
