| Age | Commit message (Collapse) | Author |
|---|
|
The common QPIC code does not do any boundary checking when it handles
the command elements and scatter gater list arrays of a BAM transaction,
thus it allows to access out of bounds elements in those.
Although it is the responsibility of the given driver to allocate enough
space for all possible BAM transaction variations, however there can be
mistakes in the driver code which can lead to hidden memory corruption
issues which are hard to debug.
This kind of problem has been observed during testing the 'spi-qpic-snand'
driver. Although the driver has been fixed with a preceding patch, but it
still makes sense to reduce the chance of having such errors again later.
In order to prevent such errors, change the qcom_alloc_bam_transaction()
function to store the number of elements of the arrays in the
'bam_transaction' strucutre during allocation. Also, add sanity checks to
the qcom_prep_bam_dma_desc_{cmd,data}() functions to avoid using out of
bounds indices for the arrays.
Tested-by: Lakshmi Sowjanya D <quic_laksd@quicinc.com> # on SDX75
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Link: https://patch.msgid.link/20250618-qpic-snand-avoid-mem-corruption-v3-2-319c71296cda@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Using the mtd_nandbiterrs module for testing the driver occasionally
results in weird things like below.
1. swiotlb mapping fails with the following message:
[ 85.926216] qcom_snand 79b0000.spi: swiotlb buffer is full (sz: 4294967294 bytes), total 512 (slots), used 0 (slots)
[ 85.932937] qcom_snand 79b0000.spi: failure in mapping desc
[ 87.999314] qcom_snand 79b0000.spi: failure to write raw page
[ 87.999352] mtd_nandbiterrs: error: write_oob failed (-110)
Rebooting the board after this causes a panic due to a NULL pointer
dereference.
2. If the swiotlb mapping does not fail, rebooting the board may result
in a different panic due to a bad spinlock magic:
[ 256.104459] BUG: spinlock bad magic on CPU#3, procd/2241
[ 256.104488] Unable to handle kernel paging request at virtual address ffffffff0000049b
...
Investigating the issue revealed that these symptoms are results of
memory corruption which is caused by out of bounds access within the
driver.
The driver uses a dynamically allocated structure for BAM transactions,
which structure must have enough space for all possible variations of
different flash operations initiated by the driver. The required space
heavily depends on the actual number of 'codewords' which is calculated
from the pagesize of the actual NAND chip.
Although the qcom_nandc_alloc() function allocates memory for the BAM
transactions during probe, but since the actual number of 'codewords'
is not yet know the allocation is done for one 'codeword' only.
Because of this, whenever the driver does a flash operation, and the
number of the required transactions exceeds the size of the allocated
arrays the driver accesses memory out of the allocated range.
To avoid this, change the code to free the initially allocated BAM
transactions memory, and allocate a new one once the actual number of
'codewords' required for a given NAND chip is known.
Fixes: 7304d1909080 ("spi: spi-qpic: add driver for QCOM SPI NAND flash Interface")
Reviewed-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Link: https://patch.msgid.link/20250618-qpic-snand-avoid-mem-corruption-v3-1-319c71296cda@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In probe(), two arrays of structs are allocated with the devm_kmalloc()
function, but the memory size of the allocations were given as the arrays'
length (pmic->common_irq_size for the first call and pmic->dev_irq_size for
the second devm_kmalloc call). The memory size should have been the total
memory needed.
This led to a heap overflow when the struct array was used. The issue was
first discovered with the PocketBeagle2 and BeaglePlay. The common and
device-specific structs are now allocated one at a time within the loop.
Fixes: 38c9f98db20a ("regulator: tps65219: Add support for TPS65215 Regulator IRQs")
Reported-by: Dhruva Gole <d-gole@ti.com>
Closes: https://lore.kernel.org/all/20250619153526.297398-1-d-gole@ti.com/
Tested-by: Robert Nelson <robertcnelson@gmail.com>
Acked-by: Andrew Davis <afd@ti.com>
Signed-off-by: Shree Ramamoorthy <s-ramamoorthy@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Link: https://patch.msgid.link/20250620154541.2713036-1-s-ramamoorthy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Failing to reset coupling_desc.n_coupled after freeing coupled_rdevs can
lead to NULL pointer dereference when regulators are accessed post-unbind.
This can happen during runtime PM or other regulator operations that rely
on coupling metadata.
For example, on ridesx4, unbinding the 'reg-dummy' platform device triggers
a panic in regulator_lock_recursive() due to stale coupling state.
Ensure n_coupled is set to 0 to prevent access to invalid pointers.
Signed-off-by: Alessandro Carminati <acarmina@redhat.com>
Link: https://patch.msgid.link/20250626083809.314842-1-acarmina@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fix from Greg KH:
"Here is a single staging driver fix for 6.16-rc4. It resolves a build
error in the rtl8723bs driver for some versions of clang on arm64 when
checking the frame size with -Wframe-larger-than.
It has been in linux-next for a while now with no reported issues"
* tag 'staging-6.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: rtl8723bs: Avoid memset() in aes_cipher() and aes_decipher()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are five small serial and tty and vt fixes for 6.16-rc4. Included
in here are:
- kerneldoc fixes for recent vt changes
- imx serial driver fix
- of_node sysfs fix for a regression
- vt missing notification fix
- 8250 dt bindings fix
All of these have been in linux-next for a while with no reported issues"
* tag 'tty-6.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
dt-bindings: serial: 8250: Make clocks and clock-frequency exclusive
serial: imx: Restore original RXTL for console to fix data loss
serial: core: restore of_node information in sysfs
vt: fix kernel-doc warnings in ucs_get_fallback()
vt: add missing notification when switching back to text mode
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras
Pull EDAC fix from Borislav Petkov:
- Consider secondary address mask registers in amd64_edac in order to
get the correct total memory size of the system
* tag 'edac_urgent_for_v6.16_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
EDAC/amd64: Fix size calculation for Non-Power-of-Two DIMMs
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
- Make sure DR6 and DR7 are initialized to their architectural values
and not accidentally cleared, leading to misconfigurations
* tag 'x86_urgent_for_v6.16_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/traps: Initialize DR7 by writing its architectural reset value
x86/traps: Initialize DR6 by writing its architectural reset value
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fix from Borislav Petkov:
- Make sure an AUX perf event is really disabled when it overruns
* tag 'perf_urgent_for_v6.16_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/aux: Fix pending disable flow when the AUX ring buffer overruns
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fix from Borislav Petkov:
- Make sure the new futex phash is not copied during fork in order to
avoid a double-free
* tag 'locking_urgent_for_v6.16_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
futex: Initialize futex_phash_new during fork().
|
|
In the past %pK was preferable to %p as it would not leak raw pointer
values into the kernel log.
Since commit ad67b74d2469 ("printk: hash addresses printed with %p")
the regular %p has been improved to avoid this issue.
Furthermore, restricted pointers ("%pK") were never meant to be used
through printk(). They can still unintentionally leak raw pointers or
acquire sleeping locks in atomic contexts.
Switch to the regular pointer formatting which is safer and
easier to reason about.
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
Commit c9b1150a68d9 ("drm/atomic-helper: Re-order bridge chain pre-enable
and post-disable") changed the call sequence to the CRTC enable/disable
and bridge pre_enable/post_disable methods, so those bridge methods are
now called when CRTC is not yet enabled.
This causes a lockup observed on Samsung Peach-Pit/Pi Chromebooks. The
source of this lockup is a call to fimd_dp_clock_enable() function, when
FIMD device is not yet runtime resumed. It worked before the mentioned
commit only because the CRTC implemented by the FIMD driver was always
enabled what guaranteed the FIMD device to be runtime resumed.
This patch adds runtime PM guards to the fimd_dp_clock_enable() function
to enable its proper operation also when the CRTC implemented by FIMD is
not yet enabled.
Fixes: 196e059a8a6a ("drm/exynos: convert clock_enable crtc callback to pipeline clock")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
If there's support for another console device (such as a TTY serial),
the kernel occasionally panics during boot. The panic message and a
relevant snippet of the call stack is as follows:
Unable to handle kernel NULL pointer dereference at virtual address 000000000000000
Call trace:
drm_crtc_handle_vblank+0x10/0x30 (P)
decon_irq_handler+0x88/0xb4
[...]
Otherwise, the panics don't happen. This indicates that it's some sort
of race condition.
Add a check to validate if the drm device can handle vblanks before
calling drm_crtc_handle_vblank() to avoid this.
Cc: stable@vger.kernel.org
Fixes: 96976c3d9aff ("drm/exynos: Add DECON driver")
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
In the past %pK was preferable to %p as it would not leak raw pointer
values into the kernel log.
Since commit ad67b74d2469 ("printk: hash addresses printed with %p")
the regular %p has been improved to avoid this issue.
Furthermore, restricted pointers ("%pK") were never meant to be used
through printk(). They can still unintentionally leak raw pointers or
acquire sleeping locks in atomic contexts.
Switch to the regular pointer formatting which is safer and
easier to reason about.
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
- imx: fix SMBus protocol compliance during block read
- omap: fix error handling path in probe
- robotfuzz, tiny-usb: prevent zero-length reads
- x86, designware, amdisp: fix build error when modules are disabled
(agreed to go in via i2c)
- scx200_acb: fix build error because of missing HAS_IOPORT
* tag 'i2c-for-6.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: scx200_acb: depends on HAS_IOPORT
i2c: omap: Fix an error handling path in omap_i2c_probe()
platform/x86: Use i2c adapter name to fix build errors
i2c: amd-isp: Initialize unique adapter name
i2c: designware: Initialize adapter name only when not set
i2c: tiny-usb: disable zero-length read messages
i2c: robotfuzz-osif: disable zero-length read messages
i2c: imx: fix emulated smbus block read
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracing fix from Steven Rostedt:
- Fix possible UAF on error path in filter_free_subsystem_filters()
When freeing a subsystem filter, the filter for the subsystem is
passed in to be freed and all the events within the subsystem will
have their filter freed too. In order to free without waiting for RCU
synchronization, list items are allocated to hold what is going to be
freed to free it via a call_rcu(). If the allocation of these items
fails, it will call the synchronization directly and free after that
(causing a bit of delay for the user).
The subsystem filter is first added to this list and then the filters
for all the events under the subsystem. The bug is if one of the
allocations of the list items for the event filters fail to allocate,
it jumps to the "free_now" label which will free the subsystem
filter, then all the items on the allocated list, and then the event
filters that were not added to the list yet. But because the
subsystem filter was added first, it gets freed twice.
The solution is to add the subsystem filter after the events, and
then if any of the allocations fail it will not try to free any of
them twice
* tag 'trace-v6.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing: Fix filter logic error
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson
Pull LoongArch fixes from Huacai Chen:
- replace __ASSEMBLY__ with __ASSEMBLER__ in headers like others
- fix build warnings about export.h
- reserve the EFI memory map region for kdump
- handle __init vs inline mismatches
- fix some KVM bugs
* tag 'loongarch-fixes-6.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson:
LoongArch: KVM: Disable updating of "num_cpu" and "feature"
LoongArch: KVM: Check validity of "num_cpu" from user space
LoongArch: KVM: Check interrupt route from physical CPU
LoongArch: KVM: Fix interrupt route update with EIOINTC
LoongArch: KVM: Add address alignment check for IOCSR emulation
LoongArch: KVM: Avoid overflow with array index
LoongArch: Handle KCOV __init vs inline mismatches
LoongArch: Reserve the EFI memory map region
LoongArch: Fix build warnings about export.h
LoongArch: Replace __ASSEMBLY__ with __ASSEMBLER__ in headers
|
|
According to Documentation/PCI/pci-error-recovery.rst only the
error_detected() callback in the err_handler struct is mandatory for
a driver to support error recovery. So far s390's error recovery chose
a stricter approach also requiring slot_reset() and resume().
Relax this requirement and only require error_detected(). If a callback
is not implemented EEH and AER treat this as PCI_ERS_RESULT_NONE. This
return value is otherwise used by drivers abstaining from their vote
on how to proceed with recovery and currently also not supported by
s390's recovery code.
So to support missing callbacks in-line with other implementors of the
recovery flow, also handle PCI_ERS_RESULT_NONE. Since s390 only does per
PCI function recovery and does not do voting, treat PCI_ERS_RESULT_NONE
optimistically and proceed through recovery unless other failures
prevent this.
Reviewed-by: Farhan Ali <alifm@linux.ibm.com>
Reviewed-by: Julian Ruess <julianr@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
|
|
If a device is disabled unblocking load/store on its own is not useful
as a full re-enable of the function is necessary anyway. Note that SCLP
Write Event Data Action Qualifier 0 (Reset) leaves the device disabled
and triggers this case unless the driver already requests a reset.
Cc: stable@vger.kernel.org
Fixes: 4cdf2f4e24ff ("s390/pci: implement minimal PCI error recovery")
Reviewed-by: Farhan Ali <alifm@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
|
|
The error event information for PCI error events contains a function
handle for the respective function. This handle is generally captured at
the time the error event was recorded. Due to delays in processing or
cascading issues, it may happen that during firmware recovery multiple
events are generated. When processing these events in order Linux may
already have recovered an affected function making the event information
stale. Fix this by doing an unconditional CLP List PCI function
retrieving the current function handle with the zdev->state_lock held
and ignoring the event if its function handle is stale.
Cc: stable@vger.kernel.org
Fixes: 4cdf2f4e24ff ("s390/pci: implement minimal PCI error recovery")
Reviewed-by: Julian Ruess <julianr@linux.ibm.com>
Reviewed-by: Gerd Bayer <gbayer@linux.ibm.com>
Reviewed-by: Farhan Ali <alifm@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
|
|
Flush dbc requests when dbc is stopped and transfer rings are freed.
Failure to flush them lead to leaking memory and dbc completing odd
requests after resuming from suspend, leading to error messages such as:
[ 95.344392] xhci_hcd 0000:00:0d.0: no matched request
Cc: stable <stable@kernel.org>
Fixes: dfba2174dc42 ("usb: xhci: Add DbC support in xHCI driver")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250627144127.3889714-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When /dev/ttyDBC0 device is created then by default ECHO flag
is set for the terminal device. However if data arrives from
a peer before application using /dev/ttyDBC0 applies its set
of terminal flags then the arriving data will be echoed which
might not be desired behavior.
Fixes: 4521f1613940 ("xhci: dbctty: split dbc tty driver registration and unregistration functions.")
Cc: stable <stable@kernel.org>
Signed-off-by: Łukasz Bartosik <ukaszb@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/stable/20250610111802.18742-1-ukaszb%40chromium.org
Link: https://lore.kernel.org/r/20250627144127.3889714-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Disable stream for platform xHC controller with broken stream.
Fixes: 14aec589327a6 ("storage: accept some UAS devices if streams are unavailable")
Cc: stable <stable@kernel.org>
Signed-off-by: Hongyu Xie <xiehongyu1@kylinos.cn>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250627144127.3889714-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
During the High-Speed Isochronous Audio transfers, xHCI
controller on certain AMD platforms experiences momentary data
loss. This results in Missed Service Errors (MSE) being
generated by the xHCI.
The root cause of the MSE is attributed to the ISOC OUT endpoint
being omitted from scheduling. This can happen when an IN
endpoint with a 64ms service interval either is pre-scheduled
prior to the ISOC OUT endpoint or the interval of the ISOC OUT
endpoint is shorter than that of the IN endpoint. Consequently,
the OUT service is neglected when an IN endpoint with a service
interval exceeding 32ms is scheduled concurrently (every 64ms in
this scenario).
This issue is particularly seen on certain older AMD platforms.
To mitigate this problem, it is recommended to adjust the service
interval of the IN endpoint to not exceed 32ms (interval 8). This
adjustment ensures that the OUT endpoint will not be bypassed,
even if a smaller interval value is utilized.
Cc: stable <stable@kernel.org>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250627144127.3889714-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 96c7bf8f6b3e ("usb: dwc3: gadget: Cleanup SG handling") updated
the TRB reclaim path to use the TRB CHN (Chain) bit to determine whether
a TRB was part of a chain. However, this inadvertently changed the
behavior of reclaiming the final TRB in some scatter-gather or short
transfer cases.
In particular, if the final TRB did not have the CHN bit set, the
cleanup path could incorrectly skip clearing the HWO (Hardware Own)
bit, leaving stale TRBs in the ring. This resulted in broken data
transfer completions in userspace, notably for MTP over FunctionFS.
Fix this by unconditionally clearing the HWO bit during TRB reclaim,
regardless of the CHN bit state. This restores correct behavior
especially for transfers that require ZLPs or end on non-CHN TRBs.
Fixes: 61440628a4ff ("usb: dwc3: gadget: Cleanup SG handling")
Signed-off-by: Johannes Schneider <johannes.schneider@leica-geosystems.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/AM8PR06MB7521A29A8863C838B54987B6BC7BA@AM8PR06MB7521.eurprd06.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
CMCI banks are not cleared during shutdown on Intel CPUs. As a side effect,
when a kexec is performed, CPUs coming back online are unable to
rediscover/claim these occupied banks which breaks MCE reporting.
Clear the CPU ownership during shutdown via cmci_clear() so the banks can
be reclaimed and MCE reporting will become functional once more.
[ bp: Massage commit message. ]
Reported-by: Aijay Adams <aijay@meta.com>
Signed-off-by: JP Kobryn <inwardvessel@gmail.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: <stable@kernel.org>
Link: https://lore.kernel.org/20250627174935.95194-1-inwardvessel@gmail.com
|
|
Pull smb client fixes from Steve French:
- Multichannel reconnect lock ordering deadlock fix
- Fix for regression in handling native Windows symlinks
- Three smbdirect fixes:
- oops in RDMA response processing
- smbdirect memcpy issue
- fix smbdirect regression with large writes (smbdirect test cases
now all passing)
- Fix for "FAILED_TO_PARSE" warning in trace-cmd report output
* tag 'v6.16-rc3-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: Fix reading into an ITER_FOLIOQ from the smbdirect code
cifs: Fix the smbd_response slab to allow usercopy
smb: client: fix potential deadlock when reconnecting channels
smb: client: remove \t from TP_printk statements
smb: client: let smbd_post_send_iter() respect the peers max_send_size and transmit all data
smb: client: fix regression with native SMB symlinks
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"16 hotfixes.
6 are cc:stable and the remainder address post-6.15 issues or aren't
considered necessary for -stable kernels. 5 are for MM"
* tag 'mm-hotfixes-stable-2025-06-27-16-56' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
MAINTAINERS: add Lorenzo as THP co-maintainer
mailmap: update Duje Mihanović's email address
selftests/mm: fix validate_addr() helper
crashdump: add CONFIG_KEYS dependency
mailmap: correct name for a historical account of Zijun Hu
mailmap: add entries for Zijun Hu
fuse: fix runtime warning on truncate_folio_batch_exceptionals()
scripts/gdb: fix dentry_name() lookup
mm/damon/sysfs-schemes: free old damon_sysfs_scheme_filter->memcg_path on write
mm/alloc_tag: fix the kmemleak false positive issue in the allocation of the percpu variable tag->counters
lib/group_cpus: fix NULL pointer dereference from group_cpus_evenly()
mm/hugetlb: remove unnecessary holding of hugetlb_lock
MAINTAINERS: add missing files to mm page alloc section
MAINTAINERS: add tree entry to mm init block
mm: add OOM killer maintainer structure
fs/proc/task_mmu: fix PAGE_IS_PFNZERO detection for the huge zero folio
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V Fixes for 5.16-rc4
- .rodata is no longer linkd into PT_DYNAMIC.
It was not supposed to be there in the first place and resulted in
invalid (but unused) entries. This manifests as at least warnings in
llvm-readelf
- A fix for runtime constants with all-0 upper 32-bits. This should
only manifest on MMU=n kernels
- A fix for context save/restore on systems using the T-Head vector
extensions
- A fix for a conflicting "+r"/"r" register constraint in the VDSO
getrandom syscall wrapper, which is undefined behavior in clang
- A fix for a missing register clobber in the RVV raid6 implementation.
This manifests as a NULL pointer reference on some compilers, but
could trigger in other ways
- Misaligned accesses from userspace at faulting addresses are now
handled correctly
- A fix for an incorrect optimization that allowed access_ok() to mark
invalid addresses as accessible, which can result in userspace
triggering BUG()s
- A few fixes for build warnings, and an update to Drew's email address
* tag 'riscv-for-linus-5.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: export boot_cpu_hartid
Revert "riscv: Define TASK_SIZE_MAX for __access_ok()"
riscv: Fix sparse warning in vendor_extensions/sifive.c
Revert "riscv: misaligned: fix sleeping function called during misaligned access handling"
MAINTAINERS: Update Drew Fustini's email address
RISC-V: uaccess: Wrap the get_user_8 uaccess macro
raid6: riscv: Fix NULL pointer dereference caused by a missing clobber
RISC-V: vDSO: Correct inline assembly constraints in the getrandom syscall wrapper
riscv: vector: Fix context save/restore with xtheadvector
riscv: fix runtime constant support for nommu kernels
riscv: vdso: Exclude .rodata from the PT_DYNAMIC segment
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull PCI fix from Bjorn Helgaas:
- Fix a PTM debugfs build error with CONFIG_DEBUG_FS=n &&
CONFIG_PCIE_PTM=y (Manivannan Sadhasivam)
* tag 'pci-v6.16-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
PCI/PTM: Build debugfs code only if CONFIG_DEBUG_FS is enabled
|
|
Pull drm fixes from Dave Airlie:
"Regular weekly drm updates, nothing out of the ordinary, amdgpu, xe,
i915 and a few misc bits. Seems about right for this time in the
release cycle.
core:
- fix drm_writeback_connector_cleanup function signature
- use correct HDMI audio bridge in drm_connector_hdmi_audio_init
bridge:
- SN65DSI86: fix HPD
amdgpu:
- Cleaner shader support for additional GFX9 GPUs
- MES firmware compatibility fixes
- Discovery error reporting fixes
- SDMA6/7 userq fixes
- Backlight fix
- EDID sanity check
i915:
- Fix for SNPS PHY HDMI for 1080p@120Hz
- Correct DP AUX DPCD probe address
- Followup build fix for GCOV and AutoFDO enabled config
xe:
- Missing error check
- Fix xe_hwmon_power_max_write
- Move flushes
- Explicitly exit CT safe mode on unwind
- Process deferred GGTT node removals on device unwind"
* tag 'drm-fixes-2025-06-28' of https://gitlab.freedesktop.org/drm/kernel:
drm/xe: Process deferred GGTT node removals on device unwind
drm/xe/guc: Explicitly exit CT safe mode on unwind
drm/xe: move DPT l2 flush to a more sensible place
drm/xe: Move DSB l2 flush to a more sensible place
drm/bridge: ti-sn65dsi86: Add HPD for DisplayPort connector type
drm/i915: fix build error some more
drm/xe/hwmon: Fix xe_hwmon_power_max_write
drm/xe/display: Add check for alloc_ordered_workqueue()
drm/amd/display: Add sanity checks for drm_edid_raw()
drm/amd/display: Fix AMDGPU_MAX_BL_LEVEL value
drm/amdgpu/sdma7: add ucode version checks for userq support
drm/amdgpu/sdma6: add ucode version checks for userq support
drm/amd: Adjust output for discovery error handling
drm/amdgpu/mes: add compatibility checks for set_hw_resource_1
drm/amdgpu/gfx9: Add Cleaner Shader Support for GFX9.x GPUs
drm/bridge-connector: Fix bridge in drm_connector_hdmi_audio_init()
drm/dp: Change AUX DPCD probe address from DPCD_REV to LANE0_1_STATUS
drm/i915/snps_hdmi_pll: Fix 64-bit divisor truncation by using div64_u64
drm: writeback: Fix drm_writeback_connector_cleanup signature
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl
Pull Compute Express Link (CXL) fixes from Dave Jiang:
"These fixes address a few issues in the CXL subsystem, including
dealing with some bugs in the CXL EDAC and RAS drivers:
- Fix return value of cxlctl_validate_set_features()
- Fix min_scrub_cycle of a region miscaculation and add additional
documentation
- Fix potential memory leak issues for CXL EDAC
- Fix CPER handler device confusion for CXL RAS
- Fix using wrong repair type to check DRAM event record"
* tag 'cxl-fixes-6.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl:
cxl/edac: Fix using wrong repair type to check dram event record
cxl/ras: Fix CPER handler device confusion
cxl/edac: Fix potential memory leak issues
cxl/Documentation: Add more description about min/max scrub cycle
cxl/edac: Fix the min_scrub_cycle of a region miscalculation
cxl: fix return value in cxlctl_validate_set_features()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux
Pull crypto library fix from Eric Biggers:
"Fix a regression where the purgatory code sometimes fails to build"
* tag 'libcrypto-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux:
lib/crypto: sha256: Mark sha256_choose_blocks as __always_inline
|
|
The driver registered xdp_rxq_info structures via xdp_rxq_info_reg()
but failed to properly unregister them in error paths and during
removal.
Fixes: d678be1dc1ec ("dpaa2-eth: add XDP_REDIRECT support")
Signed-off-by: Fushuai Wang <wangfushuai@baidu.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://patch.msgid.link/20250626133003.80136-1-wangfushuai@baidu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The `dma_map_XXX()` functions can fail and must be checked using
`dma_mapping_error()`. This patch adds proper error handling for all
DMA mapping calls.
In `atl1_alloc_rx_buffers()`, if DMA mapping fails, the buffer is
deallocated and marked accordingly.
In `atl1_tx_map()`, previously mapped buffers are unmapped and the
packet is dropped on failure.
If `atl1_xmit_frame()` drops the packet, increment the tx_error counter.
Fixes: f3cc28c79760 ("Add Attansic L1 ethernet driver.")
Signed-off-by: Thomas Fourier <fourier.thomas@gmail.com>
Link: https://patch.msgid.link/20250625141629.114984-2-fourier.thomas@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add the NGR 200 Xbox 360 to the list of recognized controllers.
Signed-off-by: Nilton Perim Neto <niltonperimneto@gmail.com>
Link: https://lore.kernel.org/r/20250608060517.14967-1-niltonperimneto@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
To enable TLS ulp socket needs to be in established state.
This was added in commit d91c3e17f75f ("net/tls: Only attach
to sockets in ESTABLISHED state"), in 2018.
Signed-off-by: Ulrich Weber <ulrich.weber@gmail.com>
Link: https://patch.msgid.link/20250626145618.15464-1-ulrich.weber@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
"Co-posting selftests" belongs in the "netdev patch review" section,
same as "co-posting changes to user space components". It was
erroneously added as its own section.
Reviewed-by: Bagas Sanjaya <bagasdotme@gmail.com>
Link: https://patch.msgid.link/20250626182055.4161905-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Due to changes of my responsibilities within IBM i
can no longer act as maintainer for smc.
As a result of the co-operation with Alibaba over
the last years we decided to, once more, give them
more responsibility for smc by appointing
D. Wythe <alibuda@linux.alibaba.com> and
Dust Li <dust.li@linux.alibaba.com>
as maintainers as well.
Within IBM Sidraya Jayagond <sidraya@linux.ibm.com>
and Mahanta Jambigi <mjambigi@linux.ibm.com>
are going to take over the maintainership for smc.
Signed-off-by: Jan Karcher <jaka@linux.ibm.com>
Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Link: https://patch.msgid.link/20250626051653.4259-1-jaka@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
https://gitlab.freedesktop.org/drm/misc/kernel into drm-fixes
drm-misc-fixes for v6.16-rc4:
- Fix function signature of drm_writeback_connector_cleanup.
- Use correct HDMI audio bridge in drm_connector_hdmi_audio_init.
- Make HPD work on SN65DSI86.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://lore.kernel.org/r/3dd1d5e1-73b6-4b0c-a208-f7d6235cf530@linux.intel.com
|
|
If the processing of the tr->events loop fails, the filter that has been
added to filter_head will be released twice in free_filter_list(&head->rcu)
and __free_filter(filter).
After adding the filter of tr->events, add the filter to the filter_head
process to avoid triggering uaf.
Link: https://lore.kernel.org/tencent_4EF87A626D702F816CD0951CE956EC32CD0A@qq.com
Fixes: a9d0aab5eb33 ("tracing: Fix regression of filter waiting a long time on RCU synchronization")
Reported-by: syzbot+daba72c4af9915e9c894@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=daba72c4af9915e9c894
Tested-by: syzbot+daba72c4af9915e9c894@syzkaller.appspotmail.com
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Edward Adam Davis <eadavis@qq.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
Not all errors that occur in xpad_try_sending_next_out_packet() are
IO errors. Pass up the error code to the caller so that it can
decide what to do.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20250609014718.236827-3-superm1@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
When a device supporting xpad is disconnected it's expected that a
URB will fail to transmit.
Only show an error message when the error isn't -ENODEV.
Fixes: 7fc595f4c0263 ("Input: xpad - correctly handle concurrent LED and FF requests")
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20250609014718.236827-2-superm1@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"Revert a commit that attempted to fix a memory leak in an error code
path and introduced a different issue (Zhe Qiao)"
* tag 'acpi-6.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "PCI/ACPI: Fix allocated memory release on error in pci_acpi_scan_root()"
|
|
Currently, for controllers with extended advertising, the advertising
data is set in the asynchronous response handler for extended
adverstising params. As most advertising settings are performed in a
synchronous context, the (asynchronous) setting of the advertising data
is done too late (after enabling the advertising).
Move setting of adverstising data from asynchronous response handler
into synchronous context to fix ordering of HCI commands.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Fixes: a0fb3726ba55 ("Bluetooth: Use Set ext adv/scan rsp data if controller supports")
Cc: stable@vger.kernel.org
v2: https://lore.kernel.org/linux-bluetooth/20250626115209.17839-1-ceggers@arri.de/
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The unconditional call of hci_disable_advertising_sync() in
mesh_send_done_sync() also disables other LE advertisings (non mesh
related).
I am not sure whether this call is required at all, but checking the
adv_instances list (like done at other places) seems to solve the
problem.
Fixes: b338d91703fa ("Bluetooth: Implement support for Mesh")
Cc: stable@vger.kernel.org
Signed-off-by: Christian Eggers <ceggers@arri.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
According to the message of commit b338d91703fa ("Bluetooth: Implement
support for Mesh"), MGMT_OP_SET_MESH_RECEIVER should set the passive scan
parameters. Currently the scan interval and window parameters are
silently ignored, although user space (bluetooth-meshd) expects that
they can be used [1]
[1] https://git.kernel.org/pub/scm/bluetooth/bluez.git/tree/mesh/mesh-io-mgmt.c#n344
Fixes: b338d91703fa ("Bluetooth: Implement support for Mesh")
Cc: stable@vger.kernel.org
Signed-off-by: Christian Eggers <ceggers@arri.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This reverts minor parts of the changes made in commit b338d91703fa
("Bluetooth: Implement support for Mesh"). It looks like these changes
were only made for development purposes but shouldn't have been part of
the commit.
Fixes: b338d91703fa ("Bluetooth: Implement support for Mesh")
Cc: stable@vger.kernel.org
Signed-off-by: Christian Eggers <ceggers@arri.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
