| Age | Commit message (Collapse) | Author |
|---|
|
The C ABI reverses the bitfield fill order when compiled as
little-endian.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The previous fix was still too agressive to meet ieee specs. Increase
to (14, 10).
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MD5 key lookups on a given TCP socket were being performed
incorrectly. This fix alters parameter inputs to the MD5
lookup function tcp_md5_do_lookup, which is called by functions
tcp_md5_do_add and tcp_md5_do_del. Specifically, the change now
inputs the correct address and address family required to make
a proper lookup.
Signed-off-by: Aydin Arik <aydin.arik@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The use of the 'readl' and 'writel' identifiers here causes build errors on
architectures where those are macros. This renames the fields to read32/write32
to avoid the problem.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alessandro Rubini <rubini@gnudd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If we don't allocate "arr" then the cleanup path will dereference it and
oops.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Alessandro Rubini <rubini@gnudd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This resolves the merge issues with drivers/base/firmware_class.c
Thanks to Ming Lei for the patch and hints on how to resolve it.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch fixes the EEE setup allowing to configure this support
when the link changes.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Due to some hardware integration issue, CPSW sliver modules requires a
reset across suspend/resume cycle for a successful clock gating to
CPGMAC (CPSW and Davinci MDIO) in AM335x PG1.0.
This issue is fixed in PG2.x, though to support suspend/resume on PG1.0
this reset is required.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The netlink_diag.h is in include/uapi/linux but not in the Kbuild necessary
to cause it to be exported by make headers_install.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
into next/soc
From Shawn Guo:
imx soc changes for 3.11:
* New SoCs i.MX6 Sololite and Vybrid VF610 support
* imx5 and imx6 clock fixes and additions
* Update clock driver to use of_clk_init() function
* Refactor restart routine mxc_restart() to get it work for DT boot
as well
* Clean up mxc specific ulpi access ops
* imx defconfig updates
* tag 'imx-soc-3.11' of git://git.linaro.org/people/shawnguo/linux-2.6: (29 commits)
ARM: imx_v6_v7_defconfig: Enable Vybrid VF610
ARM: imx_v6_v7_defconfig: Enable imx-wm8962 by default
ARM: clk-imx6qdl: Add clko1 configuration for imx6qdl-sabresd
ARM: imx_v6_v7_defconfig: Enable PWM and backlight options
ARM: imx: Remove mxc specific ulpi access ops
ARM: imx: add initial support for VF610
ARM: imx: add VF610 clock support
ARM: imx_v6_v7_defconfig: enable parallel display
ARM: imx: clk: No need to initialize phandle struct
ARM: imx: irq-common: Include header to avoid sparse warning
ARM: imx: Enable mx6 solo-lite support
ARM: imx6: use common of_clk_init() call to initialize clocks
ARM: imx6q: call of_clk_init() to register fixed rate clocks
ARM: imx: imx_v6_v7_defconfig: Select CONFIG_DRM_IMX_TVE
ARM: i.MX6: clk: add different DualLite MLB clock config
ARM i.MX5: Add S/PDIF clocks
ARM i.MX53: Add SATA clock
ARM: imx6q: clk: add the eim_slow clock
ARM: imx: remove MLB PLL from pllv3
ARM: imx: disable pll8_mlb in mx6q_clks
...
Conflicts:
arch/arm/Kconfig.debug (simple add/add conflict)
Includes an update to 3.10-rc6
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
into next/dt
From Shawn Guo:
imx device tree changes for 3.11:
* A bunch of new board additions, imx6sl-evk, vf610-twr, imx53-tx53,
imx53-m53evk and imx27-phytec-phycore
* Various pinctrl setting updates and additions
* Enable various on board peripherals, usb, audio, nor, display etc.
* Configure L2 cache data and tag latency from device tree
* Add imx-weim bus driver
* tag 'imx-dt-3.11' of git://git.linaro.org/people/shawnguo/linux-2.6: (82 commits)
ARM: dts: imx27: Add VPU devicetree node
ARM: mxc: fix gpio-ranges for VF610
ARM: dtsi: imx6qdl-sabresd: Enable WM8962 audio support
ARM: dtsi: imx6qdl-sabresd: Enable SSI2 and AUDMUX
ARM: dtsi: imx6qdl-sabresd: Add WM8962 CODEC support
ARM: dtsi: imx6qdl-sabresd: add a fixed regulator for WM8962
ARM: dtsi: imx6dl: Add a pinctrl for AUDMUX
ARM: dtsi: imx6q/imx6dl: Add a pinctrl for I2C1
ARM: dts: imx6qdl-sabresd: add clko1 iomux configuration
ARM: dts: Phytec imx6q pfla02 and pbab01 support
ARM: dts: imx6q: Add pinctrl for usdhc2 and enet
ARM: dts: imx27-phytec-phycore-rdk: Add MTD name for NOR flash
ARM: dts: imx27-phytec-phycore-rdk: Add SDHC support
ARM: dts: i.MX27: Add SDHC devicetree nodes
ARM: dts: i.MX27: Add DMA devicetree node
ARM: dts: imx6qdl-sabreauto: enable the WEIM NOR
ARM: dts: imx6dl: add pinctrls for WEIM NOR
ARM: dts: imx6q: add pinctrls for WEIM NOR
ARM: dts: imx6qdl: add more information for WEIM
ARM: dts: imx6q{dl}: fix the pin conflict between SPI and WEIM
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
into next/dt
This is a dependency for imx/dt
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
into next/dt
From Shawn Guo:
mxs device tree changes for 3.11:
* A couple of new board support, cfa10055 and cfa10057
* A few updates on cfa10036 device tree source
* Some auart pinctrl data addition
* Adopt soc bus infrastructure for mach-mxs
* tag 'mxs-dt-3.11' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: mxs: dt: Add Crystalfontz CFA-10057 device tree
ARM: mxs: dt: Add the Crystalfontz CFA-10055 device tree
ARM: cfa10049: Switch the chip select pin of the LCD controller
ARM: cfa10036: Add USB0 OTG port
ARM: dts: apf28dev: Add touchscreen support for APF28dev
ARM: mxs: Fix UARTs on M28EVK
ARM: cfa10036: dt: Change i2c0 clock frequency
ARM: dts: cfa10036: Change the OLED display to SSD1306
ARM: mx28: add auart4 2 pins pinmux to imx28.dtsi
ARM: mx28: add auart3 2 pins pinmux to imx28.dtsi
ARM: mx28: add auart2 2 pins pinmux to imx28.dtsi
ARM: mxs: Use soc bus infrastructure
ARM: dts: mx28: Adjust the digctl compatible string
ARM: mxs: Remove init_irq declaration in machine description
Includes an update to 3.10-rc6
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Commits 4c09eed9 (net: fec: Enable imx6 enet checksum acceleration) and
baa70a5c (net: fec: enable pause frame to improve rx prefomance for 1G
network) introduced functionality into the FEC driver which is not
supported on MCF5272. The registers used to implement this functionality
do not exist on MCF5272. Since register defines for MCF5272 are separate
from register defines for other chips, building images for MCF5272 fails
as follows.
fec_main.c: In function 'fec_restart':
fec_main.c:520:8: error: 'FEC_RACC' undeclared (first use in this function)
fec_main.c:585:3: error: 'FEC_R_FIFO_RSEM' undeclared (first use in this function)
fec_main.c:586:3: error: 'FEC_R_FIFO_RSFL' undeclared (first use in this function)
fec_main.c:587:3: error: 'FEC_R_FIFO_RAEM' undeclared (first use in this function)
fec_main.c:588:3: error: 'FEC_R_FIFO_RAFL' undeclared (first use in this function)
fec_main.c:591:3: error: 'FEC_OPD' undeclared (first use in this function)
Adding the missing register defines is not an option, since the registers
do not exist on MCF5272. Disable the added functionality for MCF5272 builds.
Cc: Frank Li <Frank.Li@freescale.com>
Cc: Jim Baxter <jim_baxter@mentor.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/soc
From Linus Walleij:
Device Tree and Multiplatform support for U300:
- Add devicetree support to timer, pinctrl (probe), I2C block,
watchdog, DMA controller and clocks.
- Piecewise add a device tree containing all peripherals.
- Delete the ATAG boot path.
- Delete redundant platform data and board files.
- Convert to multiplatform.
* tag 'u300-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson: (40 commits)
ARM: u300: switch to using syscon regmap for board
ARM: u300: Update MMC configs for u300 defconfig
spi: pl022: use DMA by default when probing from DT
pinctrl: get rid of all platform data for coh901
ARM: u300: convert MMC/SD clock to device tree
ARM: u300: move the gated system controller clocks to DT
i2c: stu300: do not request a specific clock name
clk: move the U300 fixed and fixed-factor to DT
ARM: u300: remove register definition file
ARM: u300: add syscon node
ARM: u300 use module_spi_driver to register driver
ARM: u300: delete remnant machine headers
ARM: u300: convert to multiplatform
ARM: u300: localize <mach/u300-regs.h>
ARM: u300: delete <mach/irqs.h>
ARM: u300: delete <mach/hardware.h>
ARM: u300: push down syscon registers
ARM: u300: remove deps from debug macro
ARM: u300: move debugmacro to debug includes
ARM: u300: delete all static board data
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
From Michal Simek:
arm: Xilinx Zynq dt changes for v3.11
The branch contains:
- DT uart handling cleanup
- Support for zc706 and zed board
- Removal of board compatible string
* tag 'zynq-dt-for-3.11' of git://git.xilinx.com/linux-xlnx:
arm: dt: zynq: Add support for the zed platform
arm: dt: zynq: Add support for the zc706 platform
arm: dt: zynq: Use 'status' property for UART nodes
arm: zynq: Remove board specific compatibility string
clk: zynq: Remove deprecated clock code
arm: zynq: Migrate platform to clock controller
clk: zynq: Add clock controller driver
clk: zynq: Factor out PLL driver
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
next/cleanup
From Michal Simek:
arm: Xilinx Zynq cleanup patches for v3.11
This branch contains two fixes:
- Fix zynq smp code
- Do not specify init_irq ptr
* tag 'zynq-cleanup-for-3.11' of git://git.xilinx.com/linux-xlnx:
ARM: zynq: Not to rewrite jump code when starting address is 0x0
ARM: zynq: Remove init_irq declaration in machine description
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
I got a build error today that made me realize that it is not
possible to build a kernel for a SiRF platform without enabling
CONFIG_PRIMA2, since a lot of common code depends on CONFIG_PRIMA2.
This fixes all occurences that appear like common SiRF code.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Mark Brown <broonie@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Barry Song <Baohua.Song@csr.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/soc
From Linus Walleij:
This is a patch series that:
- Pulls the Integrator/AP PCI bridge driver into one file
- Adds full device tree support for it
- Keeps ATAG support around for the time being
* tag 'integrator-pci-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: integrator: basic PCIv3 device tree support
ARM: integrator: move static ioremapping into PCIv3 driver
ARM: integrator: move VGA base assignment
ARM: integrator: remap PCIv3 base dynamically
ARM: integrator: move V3 register definitions into driver
ARM: integrator: move PCI base address grab to probe
ARM: integrator: grab PCI error IRQ in probe()
ARM: integrator: convert PCIv3 bridge to platform device
ARM: integrator: merge PCIv3 driver into one file
ARM: pci: create pci_common_init_dev()
Documentation/devicetree: add a small note on PCI
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add product id for Abbott strip port cable for Precision meter which
uses the TI 3410 chip.
Signed-off-by: Anders Hammarquist <iko@iko.pp.se>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 7cd8407 (ACPI / PM: Do not execute _PS0 for devices without
_PSC during initialization) introduced a regression on some systems
with Intel Lynxpoint Low-Power Subsystem (LPSS) where some devices
need to be powered up during initialization, but their device objects
in the ACPI namespace have _PS0 and _PS3 only (without _PSC or power
resources).
To work around this problem, make the ACPI LPSS driver power up
devices it knows about by using a new helper function
acpi_device_fix_up_power() that does all of the necessary
sanity checks and calls acpi_dev_pm_explicit_set() to put the
device into D0.
Reported-and-tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Commit 781d737 (ACPI: Drop power resources driver) introduced a
bug in the power resources initialization error code path causing
a NULL pointer to be referenced in acpi_release_power_resource()
if there's an error triggering a jump to the 'err' label in
acpi_add_power_resource(). This happens because the list_node
field of struct acpi_power_resource has not been initialized yet
at this point and doing a list_del() on it is a bad idea.
To prevent this problem from occuring, initialize the list_node
field of struct acpi_power_resource upfront.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: 3.9+ <stable@vger.kernel.org>
Acked-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
USB Host PHY clock on port 2 must be configured to 19.2MHz.
Provide this information.
Cc: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
|
|
On Panda the +5V supply for DVI EDID is supplied by the
same regulator that poweres the USB Hub. Currently, the
DSS/DVI subsystem doesn't know how to manage this regulator
and so DVI EDID reads will fail if USB Hub is not enabled.
As a temporary fix we keep this regulator permanently enabled
on boot. This fixes the DVI EDID read problem.
CC: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
|
|
Provide the RESET and Power regulators for the USB PHY,
the USB Host port mode and the PHY device.
Also provide pin multiplexer information for the USB host
pins.
HACK: The reset control need to be replaced with the proper
gpio-controlled reset driver as soon it will be merged [1].
[1] http://thread.gmane.org/gmane.linux.drivers.devicetree/36830
Signed-off-by: Roger Quadros <rogerq@ti.com>
[benoit.cousson@linaro.org: Add disclaimer about the reset control
inside changelog and code]
Cc: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
|
|
Since commit 3757b94 (ACPI / hotplug: Fix concurrency issues and
memory leaks) acpi_bus_scan() and acpi_bus_trim() must always be
called under acpi_scan_lock, but currently the following scenario
violating that requirement is possible:
write_undock()
handle_eject_request()
hotplug_dock_devices()
dock_remove_acpi_device()
acpi_bus_trim()
Fix that by making write_undock() acquire acpi_scan_lock before
calling handle_eject_request() as appropriate (begin_undock() is
under the lock too in analogy with acpi_dock_deferred_cb()).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: 3.9+ <stable@vger.kernel.org>
Acked-by: Toshi Kani <toshi.kani@hp.com>
|
|
acpi_get_override_irq() was added because there was a problem with
buggy BIOSes passing wrong IRQ() resource for the RTC IRQ. The
commit that added the workaround was 61fd47e0c8476 (ACPI: fix two
IRQ8 issues in IOAPIC mode).
With ACPI 5 enumerated devices there are typically one or more
extended IRQ resources per device (and these IRQs can be shared).
However, the acpi_get_override_irq() workaround forces all IRQs in
range 0 - 15 (the legacy ISA IRQs) to be edge triggered, active high
as can be seen from the dmesg below:
ACPI: IRQ 6 override to edge, high
ACPI: IRQ 7 override to edge, high
ACPI: IRQ 7 override to edge, high
ACPI: IRQ 13 override to edge, high
Also /proc/interrupts for the I2C controllers (INT33C2 and INT33C3) shows
the same thing:
7: 4 0 0 0 IO-APIC-edge INT33C2:00, INT33C3:00
The _CSR method for INT33C2 (and INT33C3) device returns following
resource:
Interrupt (ResourceConsumer, Level, ActiveLow, Shared,,, )
{
0x00000007,
}
which states that this is supposed to be level triggered, active low,
shared IRQ instead.
Fix this by making sure that acpi_get_override_irq() gets only called
when we are dealing with legacy IRQ() or IRQNoFlags() descriptors.
While we are there, correct pr_warning() to print the right triggering
value.
This change turns out to be necessary to make DMA work correctly on
systems based on the Intel Lynxpoint PCH (Platform Controller Hub).
[rjw: Changelog]
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: 3.9+ <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
We are in the process of removing all the __cpuinit annotations.
While working on making that change, an existing problem was
made evident:
WARNING: arch/x86/kernel/built-in.o(.text+0x198f2): Section mismatch
in reference from the function cpu_init() to the function
.init.text:load_ucode_ap() The function cpu_init() references
the function __init load_ucode_ap(). This is often because cpu_init
lacks a __init annotation or the annotation of load_ucode_ap is wrong.
This now appears because in my working tree, cpu_init() is no longer
tagged as __cpuinit, and so the audit picks up the mismatch. The 2nd
hypothesis from the audit is the correct one, as there was an incorrect
__init tag on the prototype in the header (but __cpuinit was used on
the function itself.)
The audit is telling us that the prototype's __init annotation took
effect and the function did land in the .init.text section. Checking
with objdump on a mainline tree that still has __cpuinit shows that
the __cpuinit on the function takes precedence over the __init on the
prototype, but that won't be true once we make __cpuinit a no-op.
Even though we are removing __cpuinit, we temporarily align both
the function and the prototype on __cpuinit so that the changeset
can be applied to stable trees if desired.
[ hpa: build fix only, no object code change ]
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: stable <stable@vger.kernel.org> # 3.9+
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Link: http://lkml.kernel.org/r/1371654926-11729-1-git-send-email-paul.gortmaker@windriver.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
This patch correctly distinguishes two boundary conditions:
1. When the given range is entire within the unaccounted space between
two rgrps, and
2. The range begins beyond the end of the filesystem
Also fix the unit of the returned value r.len (total trimming) to be in bytes
instead of the (incorrect) 512 byte blocks
With this patch, GFS2 passes multiple iterations of all the relevant xfstests
(251, 260, 288) with different fs block sizes.
Signed-off-by: Abhi Das <adas@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
|
|
This patch fixes a warning message introduced in the recent
"GFS2: aggressively issue revokes in gfs2_log_flush" patch.
Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
|
|
Provide a vdso_install target in the arm64 Makefile, as other architectures
with a vdso do.
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
None of the addi-data drivers that still use the "common" code have
ttl digital i/o. Remove the unnecessary boardinfo as well as the
subdevice initialization code.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
None of the addi-data drivers that still use the "common" code support
dma. Remove the unnecessaary boardinfo and private data flags.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Due to the on-going cleanup of the addi-data drivers, the boardinfo
used in the "common" code has a number of variables that are not
used. Remove the cruft.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Due to the on-going cleanup of the addi-data drivers, there are a
number of unused defines in addi_common.h. Remove the cruft.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
All of the remaining addi-data drivers that use the "common" code
either do not have an eeprom or the PCI controller chip is not a
PLX PCI 9054. Knowing this we can simplify the common code that
reads the PCI bars to get the iobase addresses.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Due to the on-going cleanup of the addi-data drivers, the private
data used in the "common" code has a number of variables that
either are not used at all or or set but never used.
Remove all of them from the private data and the unnecessary use
in the drivers.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch fixes the comments in r819xU_phy.c by:
- replacing "// ..." with "/* .... */"
- removing unnecessary comments, the dates and names of
developers from comments
- fixing some inconsistent comments
- fixing some typos
- fixing alignment issues
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch fixes the whitespace around ',' to meet the
linux kernel coding style.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch removes variable 'Ret' from rtl8192_QueryBBReg()
since its value is returned immediately after it is
assigned. The name 'Ret', anyway, does not give any
insight and the function description comment is sufficiently
informative regarding the returned value.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix missing free_netdev() before return from function xlr_net_probe()
in the devm_ioremap_resource() error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since my commit 3713b4e364 ("nl80211: allow splitting wiphy
information in dumps"), nl80211_dump_wiphy() uses the global
nl80211_fam.attrbuf for parsing the incoming data. This wouldn't
be a problem if it only did so on the first dump iteration which
is locked against other commands in generic netlink, but due to
space constraints in cb->args (the needed state doesn't fit) I
decided to always parse the original message. That's racy though
since nl80211_fam.attrbuf could be used by some other parsing in
generic netlink concurrently.
For now, fix this by allocating a separate parse buffer (it's a
bit too big for the stack, currently 1448 bytes on 64-bit). For
-next, I'll change the code to parse into the global buffer in
the first round only and then allocate a smaller buffer to keep
the data in cb->args.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
We need to pick up the definition of raw_smp_processor_id() from
asm/smp.h. For the !SMP case, we need to supply a definition of
raw_smp_processor_id().
Because of the include dependencies we cannot use smp_call_func_t in
asm/smp.h, but we do need linux/thread_info.h
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull sparc fixes from David Miller:
"Various sparc bug fixes, in particular:
1) TSB hashes have to be flushed before TLB on sparc64, from Dave
Kleikamp.
2) LEON timer interrupts can get stuck, from Andreas Larsson.
3) Sparc64 needs to handle lack of address-congruence devicetree
property, from Bob Picco"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: tsb must be flushed before tlb
sparc,leon: Convert to use devm_ioremap_resource
sparc64 address-congruence property
sparc32, leon: Enable interrupts before going idle to avoid getting stuck
sparc32, leon: Remove separate "ticker" timer for SMP
sparc: kernel: using strlcpy() instead of strcpy()
arch: sparc: prom: looping issue, need additional length check in the outside looping
sparc: remove inline marking of EXPORT_SYMBOL functions
sparc: Switch to asm-generic/linkage.h
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fixes from Helge Deller:
"This contains a kernel segfault fix when reading /proc/kpageflags or
/proc/kpagecount, two fixes for the serial port and PCI graphic card
support on C8000 workstations and a fix to use unshadowed registers
for flushing D- and I-caches."
* 'parisc-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Use unshadowed index register for flush instructions in flush_dcache_page_asm and flush_icache_page_asm
parisc: provide pci_mmap_page_range() for parisc
parisc: fix serial ports on C8000 workstation
parisc: fix kernel BUG at arch/parisc/include/asm/mmzone.h:50 (part 2)
|
|
Commit 106c992a5ebe ("mm/hugetlb: add more arch-defined huge_pte
functions") added an include of <asm-generic/hugetlb.h> to each
architecture's <asm/hugetlb.h> (except s390). Unfortunately metag was
missed which resulted in build errors when hugetlbfs is enabled (see
below).
Add the include for metag too to fix the build errors:
mm/hugetlb.c In function 'make_huge_pte':
mm/hugetlb.c +2250 : error: implicit declaration of function 'huge_pte_mkwrite'
mm/hugetlb.c +2250 : error: implicit declaration of function 'huge_pte_mkdirty'
...
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull ARM fixes from Russell King:
"The larger changes this time are
- "ARM: 7755/1: handle user space mapped pages in flush_kernel_dcache_page"
which fixes more data corruption problems with O_DIRECT
- "ARM: 7759/1: decouple CPU offlining from reboot/shutdown" which
gets us back to working shutdown/reboot on SMP platforms
- "ARM: 7752/1: errata: LoUIS bit field in CLIDR register is incorrect"
which fixes a shutdown regression found in v3.10 on Versatile
Express platforms.
The remainder are the quite small, maybe one or two line changes"
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7759/1: decouple CPU offlining from reboot/shutdown
ARM: 7756/1: zImage/virt: remove hyp-stub.S during distclean
ARM: 7755/1: handle user space mapped pages in flush_kernel_dcache_page
ARM: 7754/1: Fix the CPU ID and the mask associated to the PJ4B
ARM: 7753/1: map_init_section flushes incorrect pmd
ARM: 7752/1: errata: LoUIS bit field in CLIDR register is incorrect
|
|
The CLOCKSOURCE_OF_DECLARE functions now take a device_node pointer
as their argument, as of the clksrc/cleanup branch in arm-soc.
This patch adapts the bcm_kona_timer driver to the new interface.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Christian Daudt <csd@broadcom.com>
Cc: John Stultz <john.stultz@linaro.org>
|
