| Age | Commit message (Collapse) | Author |
|---|
|
The June 2015 Intel SDM introduced IP Compression types 4 and 6. Refer
to section 36.4.2.2 Target IP (TIP) Packet - IP Compression.
Existing Intel PT packet decoder did not support type 4, and got type 6
wrong. Because type 3 and type 4 have the same number of bytes, the
packet 'count' has been changed from being the number of ip bytes to
being the type code. That allows the Intel PT decoder to correctly
decide whether to sign-extend or use the last ip. However that also
meant the code had to be adjusted in a number of places.
Currently hardware is not using the new compression types, so this fix
has no effect on existing hardware.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/1469005206-3049-1-git-send-email-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Executing from a non-executable area gives an ugly message:
lkdtm: Performing direct entry EXEC_RODATA
lkdtm: attempting ok execution at ffff0000084c0e08
lkdtm: attempting bad execution at ffff000008880700
Bad mode in Synchronous Abort handler detected on CPU2, code 0x8400000e -- IABT (current EL)
CPU: 2 PID: 998 Comm: sh Not tainted 4.7.0-rc2+ #13
Hardware name: linux,dummy-virt (DT)
task: ffff800077e35780 ti: ffff800077970000 task.ti: ffff800077970000
PC is at lkdtm_rodata_do_nothing+0x0/0x8
LR is at execute_location+0x74/0x88
The 'IABT (current EL)' indicates the error but it's a bit cryptic
without knowledge of the ARM ARM. There is also no indication of the
specific address which triggered the fault. The increase in kernel
page permissions makes hitting this case more likely as well.
Handling the case in the vectors gives a much more familiar looking
error message:
lkdtm: Performing direct entry EXEC_RODATA
lkdtm: attempting ok execution at ffff0000084c0840
lkdtm: attempting bad execution at ffff000008880680
Unable to handle kernel paging request at virtual address ffff000008880680
pgd = ffff8000089b2000
[ffff000008880680] *pgd=00000000489b4003, *pud=0000000048904003, *pmd=0000000000000000
Internal error: Oops: 8400000e [#1] PREEMPT SMP
Modules linked in:
CPU: 1 PID: 997 Comm: sh Not tainted 4.7.0-rc1+ #24
Hardware name: linux,dummy-virt (DT)
task: ffff800077f9f080 ti: ffff800008a1c000 task.ti: ffff800008a1c000
PC is at lkdtm_rodata_do_nothing+0x0/0x8
LR is at execute_location+0x74/0x88
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Sorry to refer incorrect clock diagram, we double check it that the bits
configuration of the Xpll_aclk_perihp_src need to be fixed:
bit 1 - shows aclk_perihp_cpll_src_en
bit 0 - shows aclk_perihp_gpll_src_en
Through the testing that plug/unplug the USB ethernet cable on the RK3399 kevin board.
1. the hclk_host0 and hclk_host1 are endpoint clocks:
cpll --> G5[1] --> aclk_perihp_cpll_src --\ |--> hclk_host0
| --> ... ---> |
gpll --> G5[0] --> aclk_perihp_gpll_src --/ |--> hclk_host1
2. there is no clock below the cpll_aclk_perihp_src,
and the hclk_hostX are below the gpll_aclk_perihp_src:
pll_cpll 1 1 800000000 0 0
cpll 7 19 800000000 0 0
cpll_aclk_perihp_src 0 0 800000000 0 0
...
pll_gpll 1 1 594000000 0 0
gpll 10 10 594000000 0 0
gpll_aclk_perihp_src 2 2 594000000 0 0
hclk_perihp 5 5 74250000 0 0
hclk_host1_arb 2 2 74250000 0 0
hclk_host1 2 2 74250000 0 0
hclk_host0_arb 2 2 74250000 0 0
hclk_host0 2 2 74250000 0 0
3. by default, G5[0] and G5[1] are enabled:
localhost ~ # mem r 0xff760314
0x000003e0
4. close the G5[1] (aclk_perihp_cpll_src), and plug/unplug USB ethernet cable,
the DUT still works well:
localhost ~ # mem w 0xff760314 0xffff03e2
localhost ~ # mem r 0xff760314
0x000003e2
plug/unplug, the work statue is ok
5. close the G5[0] (aclk_perihp_gpll_src), , and plug/unplug USB ethernet cable,
the DUT will be crashed:
localhost ~ # mem w 0xff760314 0xffff03e1
localhost ~ # mem r 0xff760314
0x000003e1
plug/unplug, the DUT is crashed
Summary:
bit 1 - shows aclk_perihp_cpll_src_en
bit 0 - shows aclk_perihp_gpll_src_en
Fixes: 3bd14ae9da91 ("clk: rockchip: fix incorrect parent for rk3399's {c,g}pll_aclk_perihp_src")
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
[here the clock-documentation in the manual was actually stating the wrong
bits and thus only Xing's testing above revealed the issue]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.8-rc2
Here is a fix of a memory leak in a driver-registration error path, and
some new device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Signed-off-by: Thilo Cestonaro <thilo@cestona.ro>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Fix to return error code -ENODEV from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 87b2bdf02278 ("ASoC: Intel: Skylake: Initialize NHLT table")
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Acked-By: Vinod Koul <vinod.kou@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux
KVM: s390: Fixes for 4.8 (via kvm/master)
Here are two fixes found by fuzzing of the ioctl interface.
Both cases can trigger a WARN_ON_ONCE from user space.
|
|
Propagate errors from kvm_mips_handle_kseg0_tlb_fault() and
kvm_mips_handle_mapped_seg_tlb_fault(), usually triggering an internal
error since they normally indicate the guest accessed bad physical
memory or the commpage in an unexpected way.
Fixes: 858dd5d45733 ("KVM/MIPS32: MMU/TLB operations for the Guest.")
Fixes: e685c689f3a8 ("KVM/MIPS32: Privileged instruction/target branch emulation.")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: <stable@vger.kernel.org> # 3.10.x-
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
Two consecutive gfns are loaded into host TLB, so ensure the range check
isn't off by one if guest_pmap_npages is odd.
Fixes: 858dd5d45733 ("KVM/MIPS32: MMU/TLB operations for the Guest.")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: <stable@vger.kernel.org> # 3.10.x-
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
kvm_mips_handle_mapped_seg_tlb_fault() calculates the guest frame number
based on the guest TLB EntryLo values, however it is not range checked
to ensure it lies within the guest_pmap. If the physical memory the
guest refers to is out of range then dump the guest TLB and emit an
internal error.
Fixes: 858dd5d45733 ("KVM/MIPS32: MMU/TLB operations for the Guest.")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: <stable@vger.kernel.org> # 3.10.x-
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
kvm_mips_handle_mapped_seg_tlb_fault() appears to map the guest page at
virtual address 0 to PFN 0 if the guest has created its own mapping
there. The intention is unclear, but it may have been an attempt to
protect the zero page from being mapped to anything but the comm page in
code paths you wouldn't expect from genuine commpage accesses (guest
kernel mode cache instructions on that address, hitting trapping
instructions when executing from that address with a coincidental TLB
eviction during the KVM handling, and guest user mode accesses to that
address).
Fix this to check for mappings exactly at KVM_GUEST_COMMPAGE_ADDR (it
may not be at address 0 since commit 42aa12e74e91 ("MIPS: KVM: Move
commpage so 0x0 is unmapped")), and set the corresponding EntryLo to be
interpreted as 0 (invalid).
Fixes: 858dd5d45733 ("KVM/MIPS32: MMU/TLB operations for the Guest.")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: <stable@vger.kernel.org> # 3.10.x-
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
KVM devices were manipulating list data structures without any form of
synchronization, and some implementations of the create operations also
suffered from a lack of synchronization.
Now when we've split the xics create operation into create and init, we
can hold the kvm->lock mutex while calling the create operation and when
manipulating the devices list.
The error path in the generic code gets slightly ugly because we have to
take the mutex again and delete the device from the list, but holding
the mutex during anon_inode_getfd or releasing/locking the mutex in the
common non-error path seemed wrong.
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
As we are about to hold the kvm->lock during the create operation on KVM
devices, we should move the call to xics_debugfs_init into its own
function, since holding a mutex over extended amounts of time might not
be a good idea.
Introduce an init operation on the kvm_device_ops struct which cannot
fail and call this, if configured, after the device has been created.
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
This is likely that checking 'phy->hsic_clk' instead of 'phy->clk' is
expected here.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Chen-Yu Tsai <wens@csie.org
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Return proper error instead of 0 if brcm_sata_phy_init fails.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Create a new header file for TI DA8XX SoC CFGCHIPx registers.
This will be used by a number of planned drivers including a new USB
PHY driver and common clock framework drivers.
The same defines *will* be removed from the platform_data header,
once all the users start using the new syscon device header.
This also fixes the following compiler error caused due to
a dependent patch not merged.
drivers/phy/phy-da8xx-usb.c:19:37:
fatal error: linux/mfd/da8xx-cfgchip.h: No such file or directory
#include <linux/mfd/da8xx-cfgchip.h>
Signed-off-by: David Lechner <david@lechnology.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Use the new of_usb_get_dr_mode_by_phy() function to get the dr_mode
from the musb controller node instead of assuming that having an id_det
gpio means otg mode, and not having one means host mode.
Implement peripheral-only mode by adding a sun4i_usb_phy0_get_id_det
helper which looks at the dr_mode, always registering our extcon and
always monitoring vbus.
If dr_mode is not specified in the dts, do not register phy0 as we then
do not know how to treat it. This is actually a good thing as this means
we will not be registering phy0 on devices where the otg controller is
not enabled in the devicetree.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Dues to incorrect diagram, we need to fix incorrect bits for
(c/g)pll_aclk_emmc_src:
cpll_aclk_emmc_src --> G6[13]
gpll_aclk_emmc_src --> G6[12]
Fixes: 115510053e5e ("clk: rockchip: add clock controller for the RK3399")
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
When triggering KVM_RUN without a user memory region being mapped
(KVM_SET_USER_MEMORY_REGION) a validity intercept occurs. This could
happen, if the user memory region was not mapped initially or if it
was unmapped after the vcpu is initialized. The function
kvm_s390_handle_requests checks for the KVM_REQ_MMU_RELOAD bit. The
check function always clears this bit. If gmap_mprotect_notify
returns an error code, the mapping failed, but the KVM_REQ_MMU_RELOAD
was not set anymore. So the next time kvm_s390_handle_requests is
called, the execution would fall trough the check for
KVM_REQ_MMU_RELOAD. The bit needs to be resetted, if
gmap_mprotect_notify returns an error code. Resetting the bit with
kvm_make_request(KVM_REQ_MMU_RELOAD, vcpu) fixes the bug.
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Julius Niedworok <jniedwor@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
|
|
When KVM_RUN is triggered on a VCPU without an initial reset, a
validity intercept occurs.
Setting the prefix will set the KVM_REQ_MMU_RELOAD bit initially,
thus preventing the bug.
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Julius Niedworok <jniedwor@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
|
|
There are bug reports about miscounting uncore counters on some
client machines like Sandybridge, Broadwell and Skylake. It is
very likely to be observed on idle systems.
This issue is caused by a hardware issue. PERF_GLOBAL_CTL could be
cleared after Package C7, and nothing will be count.
The related errata (HSD 158) could be found in:
www.intel.com/content/dam/www/public/us/en/documents/specification-updates/4th-gen-core-family-desktop-specification-update.pdf
This patch tries to work around this issue by re-enabling PERF_GLOBAL_CTL
in ->enable_box(). The workaround does not cover all cases. It helps for new
events after returning from C7. But it cannot prevent C7, it will still
miscount if a counter is already active.
There is no drawback in leaving it enabled, so it does not need
disable_box() here.
Signed-off-by: Kan Liang <kan.liang@intel.com>
Cc: <stable@vger.kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: http://lkml.kernel.org/r/1470925874-59943-1-git-send-email-kan.liang@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Some uncore boxes' num_counters value for Haswell server and
Broadwell server are not correct (too large, off by one).
This issue was found by comparing the code with the document. Although
there is no bug report from users yet, accessing non-existent counters
is dangerous and the behavior is undefined: it may cause miscounting or
even crashes.
This patch makes them consistent with the uncore document.
Reported-by: Lukasz Odzioba <lukasz.odzioba@intel.com>
Signed-off-by: Kan Liang <kan.liang@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/1470925820-59847-1-git-send-email-kan.liang@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Since instruction decoder now supports EVEX-encoded instructions, two fixes
are needed to correctly handle them in uprobes.
Extended bits for MODRM.rm field need to be sanitized just like we do it
for VEX3, to avoid encoding wrong register for register-relative access.
EVEX has _two_ extended bits: b and x. Theoretically, EVEX.x should be
ignored by the CPU (since GPRs go only up to 15, not 31), but let's be
paranoid here: proper encoding for register-relative access
should have EVEX.x = 1.
Secondly, we should fetch vex.vvvv for EVEX too.
This is now super easy because instruction decoder populates
vex_prefix.bytes[2] for all flavors of (e)vex encodings, even for VEX2.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Acked-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jim Keniston <jkenisto@us.ibm.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: linux-kernel@vger.kernel.org
Cc: <stable@vger.kernel.org> # v4.1+
Fixes: 8a764a875fe3 ("x86/asm/decoder: Create artificial 3rd byte for 2-byte VEX")
Link: http://lkml.kernel.org/r/20160811154521.20469-1-dvlasenk@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
into drm-fixes
Some AMD fixes and remove workaround now we have pcieport pm.
* 'drm-fixes-4.8' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: Fix memory trashing if UVD ring test fails
drm/amdgpu: fix vm init error path
Revert "drm/radeon: work around lack of upstream ACPI support for D3cold"
Revert "drm/amdgpu: work around lack of upstream ACPI support for D3cold"
|
|
git://people.freedesktop.org/~gabbayo/linux into drm-fixes
Simple amdkfd fix.
* tag 'drm-amdkfd-fixes-2016-08-09' of git://people.freedesktop.org/~gabbayo/linux:
drm/amdkfd: print doorbell offset as a hex value
|
|
Coverity reports:
result_independent_of_operands: data->features & (65536UL /* 1UL << 16 */)
is always 0 regardless of the values of its operands. This occurs as the
logical operand of if.
data->features needs to be 32 bit wide since there are more than 16 features.
Fixes: cc18da79d9b7 ("hwmon: (it87) Support up to 6 temperature sensors ... ");
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
According to the datasheet, SDn clocks are from the SDSRC clock. And
the SDSRC has a 1/2 divider. So, we should have ".sdsrc" as an internal
core clock. Otherwise, since the sdhi driver will calculate clock for
a sd card using the wrong parent clock rate, and then performance will
be not good.
Fixes: 90c073e53909da85 ("clk: shmobile: r8a7795: Add SD divider support")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable@vger.kernel.org
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Merge fixes from Andrew Morton:
"7 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm/memory_hotplug.c: initialize per_cpu_nodestats for hotadded pgdats
mm, oom: fix uninitialized ret in task_will_free_mem()
kasan: remove the unnecessary WARN_ONCE from quarantine.c
mm: memcontrol: fix memcg id ref counter on swap charge move
mm: memcontrol: fix swap counter leak on swapout from offline cgroup
proc, meminfo: use correct helpers for calculating LRU sizes in meminfo
mm/hugetlb: fix incorrect hugepages count during mem hotplug
|
|
The following oops occurs after a pgdat is hotadded:
Unable to handle kernel paging request for data at address 0x00c30001
Faulting instruction address: 0xc00000000022f8f4
Oops: Kernel access of bad area, sig: 11 [#1]
SMP NR_CPUS=2048 NUMA pSeries
Modules linked in: ip6t_rpfilter ip6t_REJECT nf_reject_ipv6 ipt_REJECT nf_reject_ipv4 xt_conntrack ebtable_nat ebtable_broute bridge stp llc ebtable_filter ebtables ip6table_nat nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_ipv6 ip6table_mangle ip6table_security ip6table_raw ip6table_filter ip6_tables iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack iptable_mangle iptable_security iptable_raw iptable_filter nls_utf8 isofs sg virtio_balloon uio_pdrv_genirq uio ip_tables xfs libcrc32c sr_mod cdrom sd_mod virtio_net ibmvscsi scsi_transport_srp virtio_pci virtio_ring virtio dm_mirror dm_region_hash dm_log dm_mod
CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 4.8.0-rc1-device #110
task: c000000000ef3080 task.stack: c000000000f6c000
NIP: c00000000022f8f4 LR: c00000000022f948 CTR: 0000000000000000
REGS: c000000000f6fa50 TRAP: 0300 Tainted: G W (4.8.0-rc1-device)
MSR: 800000010280b033 <SF,VEC,VSX,EE,FP,ME,IR,DR,RI,LE,TM[E]> CR: 84002028 XER: 20000000
CFAR: d000000001d2013c DAR: 0000000000c30001 DSISR: 40000000 SOFTE: 0
NIP refresh_cpu_vm_stats+0x1a4/0x2f0
LR refresh_cpu_vm_stats+0x1f8/0x2f0
Call Trace:
refresh_cpu_vm_stats+0x1f8/0x2f0 (unreliable)
Add per_cpu_nodestats initialization to the hotplug codepath.
Link: http://lkml.kernel.org/r/1470931473-7090-1-git-send-email-arbab@linux.vnet.ibm.com
Signed-off-by: Reza Arbab <arbab@linux.vnet.ibm.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
mm/oom_kill.c: In function `task_will_free_mem':
mm/oom_kill.c:767: warning: `ret' may be used uninitialized in this function
If __task_will_free_mem() is never called inside the for_each_process()
loop, ret will not be initialized.
Fixes: 1af8bb43269563e4 ("mm, oom: fortify task_will_free_mem()")
Link: http://lkml.kernel.org/r/1470255599-24841-1-git-send-email-geert@linux-m68k.org
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
It's quite unlikely that the user will so little memory that the per-CPU
quarantines won't fit into the given fraction of the available memory.
Even in that case he won't be able to do anything with the information
given in the warning.
Link: http://lkml.kernel.org/r/1470929182-101413-1-git-send-email-glider@google.com
Signed-off-by: Alexander Potapenko <glider@google.com>
Acked-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Andrey Konovalov <adech.fo@gmail.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Kuthonuzo Luruo <kuthonuzo.luruo@hpe.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Since commit 73f576c04b94 ("mm: memcontrol: fix cgroup creation failure
after many small jobs") swap entries do not pin memcg->css.refcnt
directly. Instead, they pin memcg->id.ref. So we should adjust the
reference counters accordingly when moving swap charges between cgroups.
Fixes: 73f576c04b941 ("mm: memcontrol: fix cgroup creation failure after many small jobs")
Link: http://lkml.kernel.org/r/9ce297c64954a42dc90b543bc76106c4a94f07e8.1470219853.git.vdavydov@virtuozzo.com
Signed-off-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: <stable@vger.kernel.org> [3.19+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
An offline memory cgroup might have anonymous memory or shmem left
charged to it and no swap. Since only swap entries pin the id of an
offline cgroup, such a cgroup will have no id and so an attempt to
swapout its anon/shmem will not store memory cgroup info in the swap
cgroup map. As a result, memcg->swap or memcg->memsw will never get
uncharged from it and any of its ascendants.
Fix this by always charging swapout to the first ancestor cgroup that
hasn't released its id yet.
[hannes@cmpxchg.org: add comment to mem_cgroup_swapout]
[vdavydov@virtuozzo.com: use WARN_ON_ONCE() in mem_cgroup_id_get_online()]
Link: http://lkml.kernel.org/r/20160803123445.GJ13263@esperanza
Fixes: 73f576c04b941 ("mm: memcontrol: fix cgroup creation failure after many small jobs")
Link: http://lkml.kernel.org/r/5336daa5c9a32e776067773d9da655d2dc126491.1470219853.git.vdavydov@virtuozzo.com
Signed-off-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: <stable@vger.kernel.org> [3.19+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
meminfo_proc_show() and si_mem_available() are using the wrong helpers
for calculating the size of the LRUs. The user-visible impact is that
there appears to be an abnormally high number of unevictable pages.
Link: http://lkml.kernel.org/r/20160805105805.GR2799@techsingularity.net
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Cc: Dave Chinner <david@fromorbit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When memory hotplug operates, free hugepages will be freed if the
movable node is offline. Therefore, /proc/sys/vm/nr_hugepages will be
incorrect.
Fix it by reducing max_huge_pages when the node is offlined.
n-horiguchi@ah.jp.nec.com said:
: dissolve_free_huge_page intends to break a hugepage into buddy, and the
: destination hugepage is supposed to be allocated from the pool of the
: destination node, so the system-wide pool size is reduced. So adding
: h->max_huge_pages-- makes sense to me.
Link: http://lkml.kernel.org/r/1470624546-902-1-git-send-email-zhongjiang@huawei.com
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Acked-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"A couple of bug fixes have come in for v4.8 so far. Since the first
few were originally meant to go into -rc1 (but didn't get sent in time
for travel reasons), the branch is unfortunately based on top of a
commit in the middle of the merge window rather than -rc1.
Content-wise we have:
- a fix for the last remaining broken build in kernelci, getting
mach-shmobile to build again with SMP disabled
- a fix for a realview regression that broke real hardware but not
the qemu model that everyone uses in practice (needed for v4.7 as
well)
- a merge conflict fix for Tegra that also broke v4.7
- two Kconfig fixes for arm64 build regressions
- a couple of arm32 build warning fixes (all harmless)
- fix the RTC on Exynos7 Espresso (which apparently never worked
right)"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
Merge tag 'pxa-fixes-v4.8' of https://github.com/rjarzmik/linux into randconfig-4.8
arm64: Kconfig: select HISILICON_IRQ_MBIGEN only if PCI is selected
arm64: Kconfig: select ALPINE_MSI only if PCI is selected
ARM: dts: realview: Fix PBX-A9 cache description
ARM: tegra: fix erroneous address in dts
ARM: dts: add syscon compatible string for AP syscon
ARM: dts: add syscon compatible string for CP syscon
ARM: oxnas: select reset controller framework
ARM: hide mach-*/ include for ARM_SINGLE_ARMV7M
ARM: don't include removed directories
Revert "ARM: aspeed: adapt defconfigs for new CONFIG_PRINTK_TIME"
ARM: shmobile: don't call platform_can_secondary_boot on UP
MAINTAINER: alpine: add a mailing list
ARM: do away with final ARCH_REQUIRE_GPIOLIB
arm64: dts: Fix RTC by providing rtc_src clock
|
|
Pull virtio/vhost fixes and cleanups from Michael Tsirkin:
"Misc fixes and cleanups all over the place"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio/s390: deprecate old transport
virtio/s390: keep early_put_chars
virtio_blk: Fix a slient kernel panic
virtio-vsock: fix include guard typo
vhost/vsock: fix vhost virtio_vsock_pkt use-after-free
9p/trans_virtio: use kvfree() for iov_iter_get_pages_alloc()
virtio: fix error handling for debug builds
virtio: fix memory leak in virtqueue_add()
|
|
Fix incorrect rk3399 aclk_vio gating bit, it should be 0, not 10.
Fixes: 115510053e5e ("clk: rockchip: add clock controller for the RK3399")
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Xing Zheng <zhengxing@rock-chips.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Pull ceph fixes from Ilya Dryomov:
"A patch for a NULL dereference bug introduced in 4.8-rc1 and a handful
of static checker fixes"
* tag 'ceph-for-4.8-rc2' of https://github.com/ceph/ceph-client:
ceph: initialize pathbase in the !dentry case in encode_caps_cb()
rbd: nuke the 32-bit pool id check
rbd: destroy header_oloc in rbd_dev_release()
ceph: fix null pointer dereference in ceph_flush_snaps()
libceph: using kfree_rcu() to simplify the code
libceph: make cancel_generic_request() static
libceph: fix return value check in alloc_msg_with_page_vector()
|
|
When running LTP's nfslock01 test, the Linux client can send a LOCK
and a FREE_STATEID request at the same time. The outcome is:
Frame 324 R OPEN stateid [2,O]
Frame 115004 C LOCK lockowner_is_new stateid [2,O] offset 672000 len 64
Frame 115008 R LOCK stateid [1,L]
Frame 115012 C WRITE stateid [0,L] offset 672000 len 64
Frame 115016 R WRITE NFS4_OK
Frame 115019 C LOCKU stateid [1,L] offset 672000 len 64
Frame 115022 R LOCKU NFS4_OK
Frame 115025 C FREE_STATEID stateid [2,L]
Frame 115026 C LOCK lockowner_is_new stateid [2,O] offset 672128 len 64
Frame 115029 R FREE_STATEID NFS4_OK
Frame 115030 R LOCK stateid [3,L]
Frame 115034 C WRITE stateid [0,L] offset 672128 len 64
Frame 115038 R WRITE NFS4ERR_BAD_STATEID
In other words, the server returns stateid L in a successful LOCK
reply, but it has already released it. Subsequent uses of stateid L
fail.
To address this, protect the generation check in nfsd4_free_stateid
with the st_mutex. This should guarantee that only one of two
outcomes occurs: either LOCK returns a fresh valid stateid, or
FREE_STATEID returns NFS4ERR_LOCKS_HELD.
Reported-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Fix-suggested-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Tested-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
|
|
irq already contains the interrupt number for the port, don't add the
port index to it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Fixes: d684a90d38e2 ("ahci: per-port msix support")
Cc: stable@vger.kernel.org v4.5+
|
|
macsec_notify() loops over the list of macsec devices configured on the
underlying device when this device is being removed. This list is part
of the rx_handler data.
However, macsec_dellink unregisters the rx_handler and frees the
rx_handler data when the last macsec device is removed from the
underlying device.
Add macsec_common_dellink() to delete macsec devices without
unregistering the rx_handler and freeing the associated data.
Fixes: 960d5848dbf1 ("macsec: fix memory leaks around rx_handler (un)registration")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We've clean skb_array in macvtap_put_queue() but still try to pop from
it during macvtap_sock_destruct(). Fix this use after free by moving
the skb array cleanup to macvtap_sock_destruct() instead.
Fixes: 362899b8725b ("macvtap: switch to use skb array")
Reported-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Tested-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we need to move xattrs into external xattr block, we call
ext4_xattr_block_set() from ext4_expand_extra_isize_ea(). That may end
up calling ext4_mark_inode_dirty() again which will recurse back into
the inode expansion code leading to deadlocks.
Protect from recursion using EXT4_STATE_NO_EXPAND inode flag and move
its management into ext4_expand_extra_isize_ea() since its manipulation
is safe there (due to xattr_sem) from possible races with
ext4_xattr_set_handle() which plays with it as well.
CC: stable@vger.kernel.org # 4.4.x
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
Because the arm64 calling standard allows stacked function arguments to be
anywhere in the stack frame, do not attempt to duplicate the stack frame for
jprobes handler functions.
Documentation changes to describe this issue have been broken out into a
separate patch in order to simultaneously address them in other
architecture(s).
Signed-off-by: David A. Long <dave.long@linaro.org>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
In sg_timeout(), req->status is set to "-ETIMEDOUT" before calling
into usb_sg_cancel(). usb_sg_cancel() will do nothing and return
directly if req->status has been set to a non-zero value. This will
cause driver hang whenever transfer time out is triggered.
This patch fixes this issue. It could be backported to stable kernel
with version later than v3.15.
Cc: stable@vger.kernel.org # 3.15+
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.8-rc1
First set of fixes for v4.8-rc cycle. Again, dwc3 is
the most active driver with over 60% of this pull
request touching it.
The most important fixes are related to scatterlist
usage with dwc3. Before this pull request, we were
increment request->actual multiple times and this
would result in request->actual being larger than
request->length.
Also, if a we received a short packet midway through
processing a scatterlist, we were not clearning HWO
bit as we should.
Other than the large dwc3 scatterlist fixes, we have
a new Device ID for Intel's Kabylake silicon.
Other drivers, such as fsl_qe_udc and renesas udc,
also got a few minor fixes. Details are in shortlog.
|
|
We did not count with the padding of xattr value when computing desired
shift of xattrs in the inode when expanding i_extra_isize. As a result
we could create unaligned start of inline xattrs. Account for alignment
properly.
CC: stable@vger.kernel.org # 4.4.x-
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
When multiple xattrs need to be moved out of inode, we did not properly
recompute total size of xattr headers in the inode and the new header
position. Thus when moving the second and further xattr we asked
ext4_xattr_shift_entries() to move too much and from the wrong place,
resulting in possible xattr value corruption or general memory
corruption.
CC: stable@vger.kernel.org # 4.4.x
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
The code in ext4_expand_extra_isize_ea() treated new_extra_isize
argument sometimes as the desired target i_extra_isize and sometimes as
the amount by which we need to grow current i_extra_isize. These happen
to coincide when i_extra_isize is 0 which used to be the common case and
so nobody noticed this until recently when we added i_projid to the
inode and so i_extra_isize now needs to grow from 28 to 32 bytes.
The result of these bugs was that we sometimes unnecessarily decided to
move xattrs out of inode even if there was enough space and we often
ended up corrupting in-inode xattrs because arguments to
ext4_xattr_shift_entries() were just wrong. This could demonstrate
itself as BUG_ON in ext4_xattr_shift_entries() triggering.
Fix the problem by introducing new isize_diff variable and use it where
appropriate.
CC: stable@vger.kernel.org # 4.4.x
Reported-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
