| Age | Commit message (Collapse) | Author |
|---|
|
This patch adds ieee802.11 VHT flags for the wcn3680b.
- RX_STBC1
- SU Beamformee
- MU Beamformee
- VHT80 SGI
- Single spatial stream
RX LDPC is declared as supported in the datasheet but not enabled at this
time.
After this patch is applied an AP should see the wcn3680 as an 802.11ac
capable device.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150822.2179261-5-bryan.odonoghue@linaro.org
|
|
This commit adds VHT rates to the wcn36xx_update_allowed_rates() routine.
Thus allowing the driver to latch the declared rates and transmit them to
the firmware in the same way as other 80211.n rates are.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150822.2179261-4-bryan.odonoghue@linaro.org
|
|
In order to send VHT parameters to wcn3680 we need to pass the extended V1
parameter structures to the firmware. These commands need to have the
version number set to 1.
This patch makes the conversion. The conversion consists of
1. Setting the version number for wcn3680 or leaving it at 0 otherwise
2. Setting the size of the packet header lower for wcn3620 and wcn3660
Once done all three chips can continue to use the same code to pass
parameters to their respective firmware. In the case of the wcn3680 the
passed structures will be slightly larger to accommodate communication of
VHT descriptors.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150822.2179261-3-bryan.odonoghue@linaro.org
|
|
In order to pass 802.11ac VHT parameters from the SoC to wcn36xx we need to
use the V1 data structures associated with BSS and STA parameters.
The means of identifying a V1 data-structure is via the SMD version field.
This patch defines a INIT_HAL_MSG_V1() which operates the same way as
INIT_HAL_MSG() with the exception that it defines VERSION1 as opposed to
VERSION0.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150822.2179261-2-bryan.odonoghue@linaro.org
|
|
This commit makes use of wcn36xx_smd_set_bss_vht_params() to extract VHT
parameters from the 80211_sta structure and latch appropriate bits in the
bss_params_v1 structure for transmission to the wcnss firmware.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150747.2179122-5-bryan.odonoghue@linaro.org
|
|
This commit modifies wcn36xx_smd_start() so that it can download wcn3680
specific firmware parameters if we are talking to the wcn3680. If not the
original generic firmware parameter table should continue to be used for
wcn3620 and wcn3660.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150747.2179122-4-bryan.odonoghue@linaro.org
|
|
This commit defines a firmware configuration for the wcn3680 which
represents a working downstream configuration. This configuration has been
successfully applied to the upstream driver with antecedent patches
resulting in the same or better through-put in comparison to the
downstream driver on the test hardware.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150747.2179122-3-bryan.odonoghue@linaro.org
|
|
In order to get 802.11ac working the way we want, additional parameters
need to be passed down to the firmware.
This patch takes the full remaining set of parameters defined in the
downstream riva/inc/wlan_hal_cfg.h and imports them into hal.h with some
minor name length adjustments.
This addition will allow us to pass a larger firmware configuration set
later on.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150747.2179122-2-bryan.odonoghue@linaro.org
|
|
For the 80MHz channel we need to set the PHY mode to one of four PHY modes
that span the 80MHz range.
This patch latches the hw_value PHY field previously defined for 5GHz
channels directly to the parameter passed to the firmware.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150708.2179043-6-bryan.odonoghue@linaro.org
|
|
This commit encodes the 802.11ac PHY mode for a given channel in the upper
bits of the hw_value field. This allows for a neat read-out and application
of the relevant PHY setting.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150708.2179043-5-bryan.odonoghue@linaro.org
|
|
Adds HW_VALUE_PHY(hw_value) an access macro that will be used to
extract a hardware specific PHY setting for a given channel.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150708.2179043-4-bryan.odonoghue@linaro.org
|
|
Uses HW_VALUE_CHANNEL() to extract the channel number from a
struct ieee80211_channel->hw_value. Once done we can use the upper bits of
the hw_value to encode PHY related data.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150708.2179043-3-bryan.odonoghue@linaro.org
|
|
Adds HW_VALUE_CHANNEL(hw_value) an access macro that will be used to
extract the channel number from struct ieee80211_channel->hw_value in
preparation for also storing PHY settings for 802.11ac in the upper bits of
hw_value.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150708.2179043-2-bryan.odonoghue@linaro.org
|
|
Board Data File (BDF) is loaded upon driver boot-up procedure.
The right board data file is identified using bus and qmi-board-id.
The problem, however, can occur when the (default) board data
file cannot fulfill with the vendor requirements and it is
necessary to use a different board data file.
Also using the chip_id for identifying the board data helps
in dealing with different variants of the board data file based
on the RF card. If the chip_id is not programmed, a default value
of 0xff will be used for parsing the board data file.
Add the support to get the variant field from DTSI and
use this information along with the chip_id to load the vendor
specific BDF.
The device tree requires addition strings to define the variant name
wifi@a000000 {
status = "okay";
qcom,ath10k-calibration-variant = "xyz-v2";
};
wifi@a800000 {
status = "okay";
qcom,ath10k-calibration-variant = "xyz-v1";
};
This would create the boarddata identifiers for the board-2.bin search
* bus=snoc,qmi-board-id=16,qmi-chip-id=0,variant=xyz-v1
* bus=snoc,qmi-board-id=17,qmi-chip-id=0,variant=xyz-v2
Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1600157948-2042-1-git-send-email-pillair@codeaurora.org
|
|
This addresses the following coccinelle warning:
drivers/net/wireless/realtek/rtlwifi/rtl8723be/dm.c:1155:27-47: WARNING:
Comparison of 0/1 to bool variable
drivers/net/wireless/realtek/rtlwifi/rtl8723be/dm.c:1156:3-23: WARNING:
Assignment of 0/1 to bool variable
drivers/net/wireless/realtek/rtlwifi/rtl8723be/dm.c:1159:3-23: WARNING:
Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200919074437.3459305-1-yanaijie@huawei.com
|
|
This addresses the following coccinelle warning:
drivers/net/wireless/realtek/rtlwifi/rtl8821ae/dm.c:2680:27-47: WARNING:
Comparison of 0/1 to bool variable
drivers/net/wireless/realtek/rtlwifi/rtl8821ae/dm.c:2683:3-23: WARNING:
Assignment of 0/1 to bool variable
drivers/net/wireless/realtek/rtlwifi/rtl8821ae/dm.c:2686:3-23: WARNING:
Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200919074428.3459234-1-yanaijie@huawei.com
|
|
This addresses the following coccinelle warning:
drivers/net/wireless/realtek/rtlwifi/rtl8192ee/dm.c:721:27-47:
WARNING: Comparison of 0/1 to bool variable
drivers/net/wireless/realtek/rtlwifi/rtl8192ee/dm.c:722:3-23: WARNING:
Assignment of 0/1 to bool variable
drivers/net/wireless/realtek/rtlwifi/rtl8192ee/dm.c:725:2-22: WARNING:
Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200919074412.3459163-1-yanaijie@huawei.com
|
|
Remove the loop and use the generic ffs instead.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/e2ab424d24b74901bc0c39f0c60f75e871adf2ba.camel@perches.com
|
|
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Acked-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200919024838.14172-1-miaoqinglang@huawei.com
|
|
There is no caller in tree, so can remove it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200918131305.20976-1-yuehaibing@huawei.com
|
|
This commit adds support for Enhanced TX MPWQE feature in the regular
(SKB) data path. A MPWQE (multi-packet work queue element) can serve
multiple packets, reducing the PCI bandwidth on control traffic.
Two new stats (tx*_mpwqe_blks and tx*_mpwqe_pkts) are added. The feature
is on by default and controlled by the skb_tx_mpwqe private flag.
In a MPWQE, eseg is shared among all packets, so eseg-based offloads
(IPSEC, GENEVE, checksum) run on a separate eseg that is compared to the
eseg of the current MPWQE session to decide if the new packet can be
added to the same session.
MPWQE is not compatible with certain offloads and features, such as TLS
offload, TSO, nonlinear SKBs. If such incompatible features are in use,
the driver gracefully falls back to non-MPWQE.
This change has no performance impact in TCP single stream test and
XDP_TX single stream test.
UDP pktgen, 64-byte packets, single stream, MPWQE off:
Packet rate: 16.96 Mpps (±0.12 Mpps) -> 17.01 Mpps (±0.20 Mpps)
Instructions per packet: 421 -> 429
Cycles per packet: 156 -> 161
Instructions per cycle: 2.70 -> 2.67
UDP pktgen, 64-byte packets, single stream, MPWQE on:
Packet rate: 16.96 Mpps (±0.12 Mpps) -> 20.94 Mpps (±0.33 Mpps)
Instructions per packet: 421 -> 329
Cycles per packet: 156 -> 123
Instructions per cycle: 2.70 -> 2.67
Enabling MPWQE can reduce PCI bandwidth:
PCI Gen2, pktgen at fixed rate of 36864000 pps on 24 CPU cores:
Inbound PCI utilization with MPWQE off: 80.3%
Inbound PCI utilization with MPWQE on: 59.0%
PCI Gen3, pktgen at fixed rate of 56064000 pps on 24 CPU cores:
Inbound PCI utilization with MPWQE off: 65.4%
Inbound PCI utilization with MPWQE on: 49.3%
Enabling MPWQE can also reduce CPU load, increasing the packet rate in
case of CPU bottleneck:
PCI Gen2, pktgen at full rate on 24 CPU cores:
Packet rate with MPWQE off: 37.5 Mpps
Packet rate with MPWQE on: 49.0 Mpps
PCI Gen3, pktgen at full rate on 24 CPU cores:
Packet rate with MPWQE off: 57.0 Mpps
Packet rate with MPWQE on: 66.8 Mpps
Burst size in all pktgen tests is 32.
CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz (x86_64)
NIC: Mellanox ConnectX-6 Dx
GCC 10.2.0
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
mlx5e_txwqe_complete performs some actions that can be taken to separate
functions:
1. Update the flags needed for hardware timestamping.
2. Stop the TX queue if it's full.
Take these actions into separate functions to be reused by the MPWQE
code in the following commit and to maintain clear responsibilities of
functions.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
As preparation for the upcoming TX MPWQE support for SKBs, rename struct
mlx5e_xdp_mpwqe to mlx5e_tx_mpwqe and move it above struct mlx5e_txqsq.
This structure will be reused in the regular SQ and in the regular TX
data path. Also rename mlx5e_xdp_xmit_data to mlx5e_xmit_data - it will
be used in the upcoming TX MPWQE flow.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
As preparation for the upcoming TX MPWQE for SKBs, create a function
(mlx5e_tx_mpwqe_is_full) to check whether an MPWQE session is full. This
function will be shared by MPWQE code for XDP and for SKBs. Defines are
renamed and moved to make them not XDP-specific.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
TX MPWQE support for SKBs is coming in one of the following patches, and
a single MPWQE can send multiple SKBs. This commit prepares the TX path
code to handle such cases:
1. An additional FIFO for SKBs is added, just like the FIFO for DMA
chunks.
2. struct mlx5e_tx_wqe_info will contain num_fifo_pkts. If a given WQE
contains only one packet, num_fifo_pkts will be zero, and the SKB will
be stored in mlx5e_tx_wqe_info, as usual. If num_fifo_pkts > 0, the SKB
pointer will be NULL, and the SKBs will be stored in the FIFO.
This change has no performance impact in TCP single stream test and
XDP_TX single stream test.
When compiled with a recent GCC, this change shows no visible
performance impact on UDP pktgen (burst 32) single stream test either:
Packet rate: 16.95 Mpps (±0.15 Mpps) -> 16.96 Mpps (±0.12 Mpps)
Instructions per packet: 429 -> 421
Cycles per packet: 160 -> 156
Instructions per cycle: 2.69 -> 2.70
CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz (x86_64)
NIC: Mellanox ConnectX-6 Dx
GCC 10.2.0
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Before this patch, mlx5e_ktls_tx_handle_resync_dump_comp checked for
resync_dump_frag_page. It happened for all WQEs without an SKB,
including padding WQEs, and required a function call. Normally, padding
WQEs happen more often than TLS resyncs. Take this check out of the
function and put it to an inline function to save a call on all padding
WQEs.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
A constant for the number of DS in an empty WQE (i.e. a WQE without data
segments) is needed in multiple places (normal TX data path, MPWQE in
XDP), but currently we have a constant for XDP and an inline formula in
normal TX. This patch introduces a common constant.
Additionally, mlx5e_xdp_mpwqe_session_start is converted to use struct
assignment, because the code nearby is touched.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Use MLX5E_XDP_MPW_MAX_WQEBBS to reserve space for a MPWQE, because it's
actually the maximal size a MPWQE can take.
Reorganize the logic that checks when to close the MPWQE session:
1. Put all checks into a single function.
2. When inline is on, make only one comparison - if it's false, the less
strict one will also be false. The compiler probably optimized it out
anyway, but it's clearer to also reflect it in the code.
The MLX5E_XDP_INLINE_WQE_* defines are also changed to make the
calculations more correct from the logical point of view. Though
MLX5E_XDP_INLINE_WQE_MAX_DS_CNT used to be 16 and didn't change its
value, the calculation used to be DIV_ROUND_UP(max inline packet size,
MLX5_SEND_WQE_DS), and the numerator should have included sizeof(struct
mlx5_wqe_inline_seg).
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
A huge function mlx5e_sq_xmit was split into several to achieve multiple
goals:
1. Reuse the code in IPoIB.
2. Better intergrate with TLS, IPSEC, GENEVE and checksum offloads. Now
it's possible to reserve space in the WQ before running eseg-based
offloads, so:
2.1. It's not needed to copy cseg and eseg after mlx5e_fill_sq_frag_edge
anymore.
2.2. mlx5e_txqsq_get_next_pi will be used instead of the legacy
mlx5e_fill_sq_frag_edge for better code maintainability and reuse.
3. Prepare for the upcoming TX MPWQE for SKBs. It will intervene after
mlx5e_sq_calc_wqe_attr to check if it's possible to use MPWQE, and the
code flow will split into two paths: MPWQE and non-MPWQE.
Two high-level functions are provided to send packets:
* mlx5e_xmit is called by the networking stack, runs offloads and sends
the packet. In one of the following patches, MPWQE support will be added
to this flow.
* mlx5e_sq_xmit_simple is called by the TLS offload, runs only the
checksum offload and sends the packet.
This change has no performance impact in TCP single stream test and
XDP_TX single stream test.
When compiled with a recent GCC, this change shows no visible
performance impact on UDP pktgen (burst 32) single stream test either:
Packet rate: 16.86 Mpps (±0.15 Mpps) -> 16.95 Mpps (±0.15 Mpps)
Instructions per packet: 434 -> 429
Cycles per packet: 158 -> 160
Instructions per cycle: 2.75 -> 2.69
CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz (x86_64)
NIC: Mellanox ConnectX-6 Dx
GCC 10.2.0
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Move mlx5e_tx_wqe_inline_mode from en/txrx.h to en_tx.c as it's only
used there.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Struct assignment guarantees that all fields of the structure are
initialized (those that are not mentioned are zeroed). It makes code
mode robust and reduces chances for unpredictable behavior when one
forgets to reset some field and it holds an old value from previous
iterations of using the structure.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
As preparation for the next patch, don't increase ihs to calculate
ds_cnt and then decrease it, but rather calculate the intermediate value
temporarily. This code has the same amount of arithmetic operations, but
now allows to split out ds_cnt calculation, which will be performed in
the next patch.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Vladimir Oltean says:
====================
Fix broken tc-flower rules for mscc_ocelot switches
All 3 switch drivers from the Ocelot family have the same bug in the
VCAP IS2 key offsets, which is that some keys are in the incorrect
order.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The IS2 IP4_TCP_UDP key offsets do not correspond to the VSC7514
datasheet. Whether they work or not is unknown to me. On VSC9959 and
VSC9953, with the same mistake and same discrepancy from the
documentation, tc-flower src_port and dst_port rules did not work, so I
am assuming the same is true here.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since these were copied from the Felix VCAP IS2 code, and only the
offsets were adjusted, the order of the bit fields is still wrong.
Fix it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some of the IS2 IP4_TCP_UDP keys are not correct, like L4_DPORT,
L4_SPORT and other L4 keys. This prevents offloaded tc-flower rules from
matching on src_port and dst_port for TCP and UDP packets.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
User space could send an invalid INET_DIAG_REQ_PROTOCOL attribute
as caught by syzbot.
BUG: KMSAN: uninit-value in inet_diag_lock_handler net/ipv4/inet_diag.c:55 [inline]
BUG: KMSAN: uninit-value in __inet_diag_dump+0x58c/0x720 net/ipv4/inet_diag.c:1147
CPU: 0 PID: 8505 Comm: syz-executor174 Not tainted 5.9.0-rc4-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x21c/0x280 lib/dump_stack.c:118
kmsan_report+0xf7/0x1e0 mm/kmsan/kmsan_report.c:122
__msan_warning+0x58/0xa0 mm/kmsan/kmsan_instr.c:219
inet_diag_lock_handler net/ipv4/inet_diag.c:55 [inline]
__inet_diag_dump+0x58c/0x720 net/ipv4/inet_diag.c:1147
inet_diag_dump_compat+0x2a5/0x380 net/ipv4/inet_diag.c:1254
netlink_dump+0xb73/0x1cb0 net/netlink/af_netlink.c:2246
__netlink_dump_start+0xcf2/0xea0 net/netlink/af_netlink.c:2354
netlink_dump_start include/linux/netlink.h:246 [inline]
inet_diag_rcv_msg_compat+0x5da/0x6c0 net/ipv4/inet_diag.c:1288
sock_diag_rcv_msg+0x24f/0x620 net/core/sock_diag.c:256
netlink_rcv_skb+0x6d7/0x7e0 net/netlink/af_netlink.c:2470
sock_diag_rcv+0x63/0x80 net/core/sock_diag.c:275
netlink_unicast_kernel net/netlink/af_netlink.c:1304 [inline]
netlink_unicast+0x11c8/0x1490 net/netlink/af_netlink.c:1330
netlink_sendmsg+0x173a/0x1840 net/netlink/af_netlink.c:1919
sock_sendmsg_nosec net/socket.c:651 [inline]
sock_sendmsg net/socket.c:671 [inline]
____sys_sendmsg+0xc82/0x1240 net/socket.c:2353
___sys_sendmsg net/socket.c:2407 [inline]
__sys_sendmsg+0x6d1/0x820 net/socket.c:2440
__do_sys_sendmsg net/socket.c:2449 [inline]
__se_sys_sendmsg+0x97/0xb0 net/socket.c:2447
__x64_sys_sendmsg+0x4a/0x70 net/socket.c:2447
do_syscall_64+0x9f/0x140 arch/x86/entry/common.c:48
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x441389
Code: e8 fc ab 02 00 48 83 c4 18 c3 0f 1f 80 00 00 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 1b 09 fc ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007fff3b02ce98 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 0000000000441389
RDX: 0000000000000000 RSI: 0000000020001500 RDI: 0000000000000003
RBP: 00000000006cb018 R08: 00000000004002c8 R09: 00000000004002c8
R10: 0000000000000004 R11: 0000000000000246 R12: 0000000000402130
R13: 00000000004021c0 R14: 0000000000000000 R15: 0000000000000000
Uninit was created at:
kmsan_save_stack_with_flags mm/kmsan/kmsan.c:143 [inline]
kmsan_internal_poison_shadow+0x66/0xd0 mm/kmsan/kmsan.c:126
kmsan_slab_alloc+0x8a/0xe0 mm/kmsan/kmsan_hooks.c:80
slab_alloc_node mm/slub.c:2907 [inline]
__kmalloc_node_track_caller+0x9aa/0x12f0 mm/slub.c:4511
__kmalloc_reserve net/core/skbuff.c:142 [inline]
__alloc_skb+0x35f/0xb30 net/core/skbuff.c:210
alloc_skb include/linux/skbuff.h:1094 [inline]
netlink_alloc_large_skb net/netlink/af_netlink.c:1176 [inline]
netlink_sendmsg+0xdb9/0x1840 net/netlink/af_netlink.c:1894
sock_sendmsg_nosec net/socket.c:651 [inline]
sock_sendmsg net/socket.c:671 [inline]
____sys_sendmsg+0xc82/0x1240 net/socket.c:2353
___sys_sendmsg net/socket.c:2407 [inline]
__sys_sendmsg+0x6d1/0x820 net/socket.c:2440
__do_sys_sendmsg net/socket.c:2449 [inline]
__se_sys_sendmsg+0x97/0xb0 net/socket.c:2447
__x64_sys_sendmsg+0x4a/0x70 net/socket.c:2447
do_syscall_64+0x9f/0x140 arch/x86/entry/common.c:48
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes: 3f935c75eb52 ("inet_diag: support for wider protocol numbers")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Christoph Paasch <cpaasch@apple.com>
Cc: Mat Martineau <mathew.j.martineau@linux.intel.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When calling the RCU brother of br_vlan_get_pvid(), lockdep warns:
=============================
WARNING: suspicious RCU usage
5.9.0-rc3-01631-g13c17acb8e38-dirty #814 Not tainted
-----------------------------
net/bridge/br_private.h:1054 suspicious rcu_dereference_protected() usage!
Call trace:
lockdep_rcu_suspicious+0xd4/0xf8
__br_vlan_get_pvid+0xc0/0x100
br_vlan_get_pvid_rcu+0x78/0x108
The warning is because br_vlan_get_pvid_rcu() calls nbp_vlan_group()
which calls rtnl_dereference() instead of rcu_dereference(). In turn,
rtnl_dereference() calls rcu_dereference_protected() which assumes
operation under an RCU write-side critical section, which obviously is
not the case here. So, when the incorrect primitive is used to access
the RCU-protected VLAN group pointer, READ_ONCE() is not used, which may
cause various unexpected problems.
I'm sad to say that br_vlan_get_pvid() and br_vlan_get_pvid_rcu() cannot
share the same implementation. So fix the bug by splitting the 2
functions, and making br_vlan_get_pvid_rcu() retrieve the VLAN groups
under proper locking annotations.
Fixes: 7582f5b70f9a ("bridge: add br_vlan_get_pvid_rcu()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes-2020-09-18
This series introduces some fixes to mlx5 driver.
Please pull and let me know if there is any problem.
v1->v2:
Remove missing patch from -stable list.
For -stable v5.1
('net/mlx5: Fix FTE cleanup')
For -stable v5.3
('net/mlx5e: TLS, Do not expose FPGA TLS counter if not supported')
('net/mlx5e: Enable adding peer miss rules only if merged eswitch is supported')
For -stable v5.7
('net/mlx5e: Fix memory leak of tunnel info when rule under multipath not ready')
For -stable v5.8
('net/mlx5e: Use RCU to protect rq->xdp_prog')
('net/mlx5e: Fix endianness when calculating pedit mask first bit')
('net/mlx5e: Use synchronize_rcu to sync with NAPI')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update maintainers for MediaTek switch driver with Landen Chao who is
familiar with MediaTek MT753x switch devices and will help maintenance
from the vendor side.
Cc: Steven Liu <steven.liu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Landen Chao <Landen.Chao@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Returning errno is a bug, fix that.
Also fixes smatch warnings:
drivers/net/ethernet/mellanox/mlx5/core/en/port.c:453
mlx5e_fec_in_caps() warn: signedness bug returning '(-95)'
Fixes: 2132b71f78d2 ("net/mlx5e: Advertise globaly supported FEC modes")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Aya Levin <ayal@nvidia.com>
|
|
The spinlock only needed when accessing the channel's icosq, grab the lock
after the buf allocation in resync_post_get_progress_params() to avoid
kzalloc(GFP_KERNEL) in atomic context.
Fixes: 0419d8c9d8f8 ("net/mlx5e: kTLS, Add kTLS RX resync support")
Reported-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
|
|
Resync progress params buffer and dma weren't released on error,
Add missing error unwinding for resync_post_get_progress_params().
Fixes: 0419d8c9d8f8 ("net/mlx5e: kTLS, Add kTLS RX resync support")
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
|
|
Progress params dma address is never unmapped, unmap it when completion
handling is over.
Fixes: 0419d8c9d8f8 ("net/mlx5e: kTLS, Add kTLS RX resync support")
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
|
|
Using synchronize_rcu() is sufficient to wait until running NAPI quits.
See similar upstream fix with detailed explanation:
("net/mlx5e: Use synchronize_rcu to sync with NAPI")
This change also fixes a possible use-after-free as the NAPI
might be already released at this stage.
Fixes: 0419d8c9d8f8 ("net/mlx5e: kTLS, Add kTLS RX resync support")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The set of TLS TX global SW counters in mlx5e_tls_sw_stats_desc
is updated from all rings by using atomic ops.
This set of stats is used only in the FPGA TLS use case, not in
the Connect-X TLS one, where regular per-ring counters are used.
Do not expose them in the Connect-X use case, as this would cause
counter duplication. For example, tx_tls_drop_no_sync_data would
appear twice in the ethtool stats.
Fixes: d2ead1f360e8 ("net/mlx5e: Add kTLS TX HW offload support")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
The cited commit started to reuse function mlx5e_update_ndo_stats() for
the representors as well.
However, the function is hard-coded to work on mlx5e_nic_stats_grps only.
Due to this issue, the representors statistics were not updated in the
output of "ip -s".
Fix it to work with the correct group by extracting it from the caller's
profile.
Also, while at it and since this function became generic, move it to
en_stats.c and rename it accordingly.
Fixes: 8a236b15144b ("net/mlx5e: Convert rep stats to mlx5e_stats_grp-based infra")
Signed-off-by: Alaa Hleihel <alaa@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Currently the FW does not generate events for counters other than error
counters. Unlike ".get_ethtool_stats", ".ndo_get_stats64" (which ip -s
uses) might run in atomic context, while the FW interface is non atomic.
Thus, 'ip' is not allowed to issue FW commands, so it will only display
cached counters in the driver.
Add a SW counter (mcast_packets) in the driver to count rx multicast
packets. The counter also counts broadcast packets, as we consider it a
special case of multicast.
Use the counter value when calling "ip -s"/"ifconfig".
Fixes: f62b8bb8f2d3 ("net/mlx5: Extend mlx5_core to support ConnectX-4 Ethernet functionality")
Signed-off-by: Ron Diskin <rondi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The field mask value is provided in network byte order and has to
be converted to host byte order before calculating pedit mask
first bit.
Fixes: 88f30bbcbaaa ("net/mlx5e: Bit sized fields rewrite support")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
The cited commit creates peer miss group during switchdev mode
initialization in order to handle miss packets correctly while in VF
LAG mode. This is done regardless of FW support of such groups which
could cause rules setups failure later on.
Fix by adding FW capability check before creating peer groups/rule.
Fixes: ac004b832128 ("net/mlx5e: E-Switch, Add peer miss rules")
Signed-off-by: Maor Dickman <maord@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Raed Salem <raeds@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
