| Age | Commit message (Collapse) | Author |
|---|
|
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains Netfilter fixes for net:
1) Crash due to missing initialization of timer data in
xt_IDLETIMER, from Juhee Kang.
2) NF_CONNTRACK_SECMARK should be bool in Kconfig, from Vegard Nossum.
3) Skip netdev events on netns removal, from Florian Westphal.
4) Add testcase to show port shadowing via UDP, also from Florian.
5) Remove pr_debug() code in ip6t_rt, this fixes a crash due to
unsafe access to non-linear skbuff, from Xin Long.
6) Make net/ipv4/vs/debug_level read-only from non-init netns,
from Antoine Tenart.
7) Remove bogus invocation to bash in selftests/netfilter/nft_flowtable.sh
also from Florian.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-fixes-2021-10-20
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2021-10-20
This series contains updates to e1000e, igc, and ice drivers.
Sasha fixes an issue with dropped packets on Tiger Lake platforms for
e1000e and corrects a device ID for igc.
Tony adds missing E810 device IDs for ice.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On KMB, ADV bridge must be programmed and powered on prior to
MIPI DSI HW initialization.
v2: changed to atomic_bridge_chain_enable (Sam)
Fixes: 98521f4d4b4c ("drm/kmb: Mipi DSI part of the display driver")
Co-developed-by: Edmund Dea <edmund.j.dea@intel.com>
Signed-off-by: Edmund Dea <edmund.j.dea@intel.com>
Signed-off-by: Anitha Chrisanthus <anitha.chrisanthus@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211019230719.789958-1-anitha.chrisanthus@intel.com
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
|
|
Check for Overflow bits for layer3 in the irq handler.
Fixes: 7f7b96a8a0a1 ("drm/kmb: Add support for KeemBay Display")
Signed-off-by: Anitha Chrisanthus <anitha.chrisanthus@intel.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211013233632.471892-5-anitha.chrisanthus@intel.com
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
|
|
Due to HW limitations, KMB cannot change height, width, or
pixel format after initial plane configuration.
v2: removed memset disp_cfg as it is already zero.
Fixes: 7f7b96a8a0a1 ("drm/kmb: Add support for KeemBay Display")
Signed-off-by: Edmund Dea <edmund.j.dea@intel.com>
Signed-off-by: Anitha Chrisanthus <anitha.chrisanthus@intel.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211013233632.471892-4-anitha.chrisanthus@intel.com
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
|
|
Don't clear the shared DPHY registers common to MIPI Rx and MIPI Tx during
DSI initialization since this was causing MIPI Rx reset. Rest of the
writes are bitwise, so will not affect Mipi Rx side.
Fixes: 98521f4d4b4c ("drm/kmb: Mipi DSI part of the display driver")
Signed-off-by: Edmund Dea <edmund.j.dea@intel.com>
Signed-off-by: Anitha Chrisanthus <anitha.chrisanthus@intel.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211013233632.471892-3-anitha.chrisanthus@intel.com
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
|
|
KMB only supports single resolution(1080p), this commit checks for
1920x1080x60 or 1920x1080x59 in crtc_mode_valid.
Also, modes with vfp < 4 are not supported in KMB display. This change
prunes display modes with vfp < 4.
v2: added vfp check
Fixes: 7f7b96a8a0a1 ("drm/kmb: Add support for KeemBay Display")
Co-developed-by: Edmund Dea <edmund.j.dea@intel.com>
Signed-off-by: Edmund Dea <edmund.j.dea@intel.com>
Signed-off-by: Anitha Chrisanthus <anitha.chrisanthus@intel.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link:https://patchwork.freedesktop.org/patch/msgid/20211013233632.471892-2-anitha.chrisanthus@intel.com
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
|
|
Use a different value for system clock offset in the
ppl/llp ratio calculations for clocks higher than 500 Mhz.
Fixes: 98521f4d4b4c ("drm/kmb: Mipi DSI part of the display driver")
Signed-off-by: Anitha Chrisanthus <anitha.chrisanthus@intel.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211013233632.471892-1-anitha.chrisanthus@intel.com
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
|
|
This adjusts sync values according to the datasheet
Fixes: 1c243751c095 ("drm/panel: ilitek-ili9881c: add support for Feixin K101-IM2BYL02 panel")
Co-developed-by: Marius Gripsgard <marius@ubports.com>
Signed-off-by: Dan Johansen <strit@manjaro.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210818214818.298089-1-strit@manjaro.org
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
|
|
The mxsfb->crtc.funcs may already be NULL when unloading the driver,
in which case calling mxsfb_irq_disable() via drm_irq_uninstall() from
mxsfb_unload() leads to NULL pointer dereference.
Since all we care about is masking the IRQ and mxsfb->base is still
valid, just use that to clear and mask the IRQ.
Fixes: ae1ed00932819 ("drm: mxsfb: Stop using DRM simple display pipeline helper")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Abrecht <public@danielabrecht.ch>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Stefan Agner <stefan@agner.ch>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211016210446.171616-1-marex@denx.de
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
|
|
Instead of "goto err", return error directly, since there's no error
cleanup to do now.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
|
|
Syzkaller reports a null pointer dereference in fuse_test_super() that is
caused by sb->s_fs_info being NULL.
This is due to the fact that fuse_fill_super() is initializing s_fs_info,
which is too late, it's already on the fs_supers list. The initialization
needs to be done in sget_fc() with the sb_lock held.
Move allocation of fuse_mount and fuse_conn from fuse_fill_super() into
fuse_get_tree().
After this ->kill_sb() will always be called with non-NULL ->s_fs_info,
hence fuse_mount_destroy() can drop the test for non-NULL "fm".
Reported-by: syzbot+74a15f02ccb51f398601@syzkaller.appspotmail.com
Fixes: 5d5b74aa9c76 ("fuse: allow sharing existing sb")
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
|
|
1. call fuse_mount_destroy() for open coded variants
2. before deactivate_locked_super() don't need fuse_mount destruction since
that will now be done (if ->s_fs_info is not cleared)
3. rearrange fuse_mount setup in fuse_get_tree_submount() so that the
regular pattern can be used
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
|
|
The ->put_super callback is called from generic_shutdown_super() in case of
a fully initialized sb. This is called from kill_***_super(), which is
called from ->kill_sb instances.
Fuse uses ->put_super to destroy the fs specific fuse_mount and drop the
reference to the fuse_conn, while it does the same on each error case
during sb setup.
This patch moves the destruction from fuse_put_super() to
fuse_mount_destroy(), called at the end of all ->kill_sb instances. A
follup patch will clean up the error paths.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
|
|
Checking "fm" works because currently sb->s_fs_info is cleared on error
paths; however, sb->s_root is what generic_shutdown_super() checks to
determine whether the sb was fully initialized or not.
This change will allow cleanup of sb setup error paths.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
|
|
Since commit c300ab9f08df ("KVM: x86: Replace late check_nested_events() hack with
more precise fix") there is no longer the certainty that check_nested_events()
tries to inject an external interrupt vmexit to L1 on every call to vcpu_enter_guest.
Therefore, even in that case we need to set KVM_REQ_EVENT. This ensures
that inject_pending_event() is called, and from there kvm_check_nested_events().
Fixes: c300ab9f08df ("KVM: x86: Replace late check_nested_events() hack with more precise fix")
Cc: stable@vger.kernel.org
Reviewed-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The kvm_x86_sync_pir_to_irr callback can sometimes set KVM_REQ_EVENT.
If that happens exactly at the time that an exit is handled as
EXIT_FASTPATH_REENTER_GUEST, vcpu_enter_guest will go incorrectly
through the loop that calls kvm_x86_run, instead of processing
the request promptly.
Fixes: 379a3c8ee444 ("KVM: VMX: Optimize posted-interrupt delivery for timer fastpath")
Cc: stable@vger.kernel.org
Reviewed-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
PA_PWRMODEUSERDATA0 -> DL_FC0PROTTIMEOUTVAL
PA_PWRMODEUSERDATA1 -> DL_TC0REPLAYTIMEOUTVAL
PA_PWRMODEUSERDATA2 -> DL_AFC0REQTIMEOUTVAL
Link: https://lore.kernel.org/r/20211018062841.18226-1-chanho61.park@samsung.com
Fixes: a967ddb22d94 ("scsi: ufs: ufs-exynos: Apply vendor-specific values for three timeouts")
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Kiwoong Kim <kwmad.kim@samsung.com>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Commit a264cf5e81c7 ("scsi: ibmvfc: Fix command state accounting and stale
response detection") introduced a regression in detecting duplicate
responses. This was observed in test where a command was sent to the VIOS
and completed before ibmvfc_send_event() set the active flag to 1, which
resulted in the atomic_dec_if_positive() call in ibmvfc_handle_crq()
thinking this was a duplicate response, which resulted in scsi_done() not
getting called, so we then hit a SCSI command timeout for this command once
the timeout expires. This simply ensures the active flag gets set prior to
making the hcall to send the command to the VIOS, in order to close this
window.
Link: https://lore.kernel.org/r/20211019152129.16558-1-brking@linux.vnet.ibm.com
Fixes: a264cf5e81c7 ("scsi: ibmvfc: Fix command state accounting and stale response detection")
Cc: stable@vger.kernel.org
Acked-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
There's a mistake in commit 2be7828c9fefc ("get rid of autofs_getpath()")
that affects kernels from v5.13.0, basically missed because of me not
fully testing the change for Al.
The problem is that the hash calculation for the wait name qstr hasn't
been updated to account for the change to use dentry_path_raw(). This
prevents the correct matching an existing wait resulting in multiple
notifications being sent to the daemon for the same mount which must
not occur.
The problem wasn't discovered earlier because it only occurs when
multiple processes trigger a request for the same mount concurrently
so it only shows up in more aggressive testing.
Fixes: 2be7828c9fefc ("get rid of autofs_getpath()")
Cc: stable@vger.kernel.org
Signed-off-by: Ian Kent <raven@themaw.net>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Pull ceph fixes from Ilya Dryomov:
"Two important filesystem fixes, marked for stable.
The blocklisted superblocks issue was particularly annoying because
for unexperienced users it essentially exacted a reboot to establish a
new functional mount in that scenario"
* tag 'ceph-for-5.15-rc7' of git://github.com/ceph/ceph-client:
ceph: fix handling of "meta" errors
ceph: skip existing superblocks that are blocklisted or shut down when mounting
|
|
Pull dma-mapping fixes from Christoph Hellwig:
- fix more dma-debug fallout (Gerald Schaefer, Hamza Mahfooz)
- fix a kerneldoc warning (Logan Gunthorpe)
* tag 'dma-mapping-5.15-2' of git://git.infradead.org/users/hch/dma-mapping:
dma-debug: teach add_dma_entry() about DMA_ATTR_SKIP_CPU_SYNC
dma-debug: fix sg checks in debug_dma_map_sg()
dma-mapping: fix the kerneldoc for dma_map_sgtable()
|
|
B0 internal rev_id is 0x01, B1 internal rev_id is 0x02.
The external rev_id for B0 and B1 is 0x20.
The original expression is not suitable for B1.
v2: squash in fix for display code (Alex)
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
[Why]
bios_golden_init will override dccg_init during init_hw.
[How]
Move dccg_init to after bios_golden_init.
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Agustin Gutierrez Sanchez <agustin.gutierrez@amd.com>
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
[why]
The original latencies were causing underflow in some modes
[how]
Replace with the up-to-date watermark values based on new measurments
Reviewed-by: Ahmad Othman <ahmad.othman@amd.com>
Acked-by: Agustin Gutierrez Sanchez <agustin.gutierrez@amd.com>
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
[Why]
Z9 latency is higher than when we originally tuned the watermark
parameters, causing underflow. Increasing the value until the latency
issues is resolved.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Agustin Gutierrez Sanchez <agustin.gutierrez@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
[Why]
Immediate flip can be enabled dynamically and has higher BW requirements
when validating which voltage mode to use.
If we validate when it's not set then potentially DCFCLK will be too low
and we will underflow.
[How]
DM always requires support so always require it as part of DML input
parameters.
This can't be enabled unconditionally on older ASIC because it blocks
some expected modes so only target DCN3.1 for now.
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Agustin Gutierrez Sanchez <agustin.gutierrez@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
[Why]
Prefetch BW calculated is lower than the DML reference because of a
porting error that's excluding cursor and row bandwidth from the
pixel data bandwidth.
[How]
Change the dml_max4 to dml_max3 and include cursor and row bandwidth
in the same calculation as the rest of the pixel data during vactive.
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Agustin Gutierrez Sanchez <agustin.gutierrez@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
[why]
The requirement is that image width up to 4096 shall be supported
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Agustin Gutierrez Sanchez <agustin.gutierrez@amd.com>
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Size can be any value and is user controlled resulting in overwriting the
40 byte array wr_buf with an arbitrary length of data from buf.
Signed-off-by: Thelford Williams <tdwilliamsiv@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Current Work Queue Entry (WQE) checksum (csum) flags in the ethernet
segment (eseg) in case of IPsec crypto offload datapath are not aligned
with PRM/HW expectations.
Currently the driver always sets the l3_inner_csum flag in case of IPsec
because of the wrong usage of skb->encapsulation as indicator for inner
IPsec header since skb->encapsulation is always ON for IPsec packets
since IPsec itself is an encapsulation protocol. The above forced a
failing attempts of calculating csum of non-existing segments (like in
the IP|ESP|TCP packet case which does not have an l3_inner) which led
to lots of packet drops hence the low throughput.
Fix by using xo->inner_ipproto as indicator for inner IPsec header
instead of skb->encapsulation in addition to setting the csum flags
as following:
* Tunnel Mode:
* Pkt: MAC IP ESP IP L4
* CSUM: l3_cs | l3_inner_cs | l4_inner_cs
*
* Transport Mode:
* Pkt: MAC IP ESP L4
* CSUM: l3_cs [ | l4_cs (checksum partial case)]
*
* Tunnel(VXLAN TCP/UDP) over Transport Mode
* Pkt: MAC IP ESP UDP VXLAN IP L4
* CSUM: l3_cs | l3_inner_cs | l4_inner_cs
Fixes: f1267798c980 ("net/mlx5: Fix checksum issue of VXLAN and IPsec crypto offload")
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
IPsec crypto offload current Software Parser (SWP) fields settings in
the ethernet segment (eseg) are not aligned with PRM/HW expectations.
Among others in case of IP|ESP|TCP packet, current driver sets the
offsets for inner_l3 and inner_l4 although there is no inner l3/l4
headers relative to ESP header in such packets.
SWP provides the offsets for HW ,so it can be used to find csum fields
to offload the checksum, however these are not necessarily used by HW
and are used as fallback in case HW fails to parse the packet, e.g
when performing IPSec Transport Aware (IP | ESP | TCP) there is no
need to add SW parse on inner packet. So in some cases packets csum
was calculated correctly , whereas in other cases it failed. The later
faced csum errors (caused by wrong packet length calculations) which
led to lots of packet drops hence the low throughput.
Fix by setting the SWP fields as expected in a IP|ESP|TCP packet.
the following describe the expected SWP offsets:
* Tunnel Mode:
* SWP: OutL3 InL3 InL4
* Pkt: MAC IP ESP IP L4
*
* Transport Mode:
* SWP: OutL3 OutL4
* Pkt: MAC IP ESP L4
*
* Tunnel(VXLAN TCP/UDP) over Transport Mode
* SWP: OutL3 InL3 InL4
* Pkt: MAC IP ESP UDP VXLAN IP L4
Fixes: f1267798c980 ("net/mlx5: Fix checksum issue of VXLAN and IPsec crypto offload")
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
During suspend flow the driver calls mlx5e_destroy_vlan_table() which
does not only delete the vlans steering flow rules, but also frees the
data on currently active vlans, thus it is not restored during resume
flow.
This fix keeps the vlan data on suspend flow and frees it only on driver
remove flow.
Fixes: 6783f0a21a3c ("net/mlx5e: Dynamic alloc vlan table for netdev when needed")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Dan Carpenter report:
The patch f47e04eb96e0: "net/mlx5: E-switch, Allow setting share/max
tx rate limits of rate groups" from May 31, 2021, leads to the
following Smatch static checker warning:
drivers/net/ethernet/mellanox/mlx5/core/esw/qos.c:483 esw_qos_create_rate_group()
warn: passing zero to 'ERR_PTR'
If min rate normalization failed then error code may be overwritten to 0
if scheduling element destruction succeed. Ignore this value and always
return initial one.
Fixes: f47e04eb96e0 ("net/mlx5: E-switch, Allow setting share/max tx rate limits of rate groups")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Both multipath and bonding events are changing the HW LAG state
independently.
Handling one of the features events while the other is already
enabled can cause unwanted behavior, for example handling
bonding event while multipath enabled will disable the lag and
cause multipath to stop working.
Fix it by ignoring bonding event while in multipath and ignoring FIB
events while in bonding mode.
Fixes: 544fe7c2e654 ("net/mlx5e: Activate HW multipath and handle port affinity based on FIB events")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
As noted in the "Deprecated Interfaces, Language Features, Attributes,
and Conventions" documentation [1], size calculations (especially
multiplication) should not be performed in memory allocator (or similar)
function arguments due to the risk of them overflowing. This could lead
to values wrapping around and a smaller allocation being made than the
caller was expecting. Using those allocations could lead to linear
overflows of heap memory and other misbehaviors.
In this case this is not actually dynamic size: all the operands
involved in the calculation are constant values. However it is better to
refactor this anyway, just to keep the open-coded math idiom out of
code.
So, use the struct_size() helper to do the arithmetic instead of the
argument "size + count * size" in the kmalloc() function.
This code was detected with the help of Coccinelle and audited and fixed
manually.
[1] https://www.kernel.org/doc/html/latest/process/deprecated.html#open-coded-arithmetic-in-allocator-arguments
Signed-off-by: Len Baker <len.baker@gmx.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
When reading the partition table on initial scan hits an I/O error the
I/O will hang with the scan_mutex held:
[<0>] do_read_cache_page+0x49b/0x790
[<0>] read_part_sector+0x39/0xe0
[<0>] read_lba+0xf9/0x1d0
[<0>] efi_partition+0xf1/0x7f0
[<0>] bdev_disk_changed+0x1ee/0x550
[<0>] blkdev_get_whole+0x81/0x90
[<0>] blkdev_get_by_dev+0x128/0x2e0
[<0>] device_add_disk+0x377/0x3c0
[<0>] nvme_mpath_set_live+0x130/0x1b0 [nvme_core]
[<0>] nvme_mpath_add_disk+0x150/0x160 [nvme_core]
[<0>] nvme_alloc_ns+0x417/0x950 [nvme_core]
[<0>] nvme_validate_or_alloc_ns+0xe9/0x1e0 [nvme_core]
[<0>] nvme_scan_work+0x168/0x310 [nvme_core]
[<0>] process_one_work+0x231/0x420
and trying to delete the controller will deadlock as it tries to grab
the scan mutex:
[<0>] nvme_mpath_clear_ctrl_paths+0x25/0x80 [nvme_core]
[<0>] nvme_remove_namespaces+0x31/0xf0 [nvme_core]
[<0>] nvme_do_delete_ctrl+0x4b/0x80 [nvme_core]
As we're now properly ordering the namespace list there is no need to
hold the scan_mutex in nvme_mpath_clear_ctrl_paths() anymore.
And we always need to kick the requeue list as the path will be marked
as unusable and I/O will be requeued _without_ a current path.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
The host memory doorbell and event buffers need to be initialized on
each reset so the driver doesn't observe stale values from the previous
instantiation.
Signed-off-by: Keith Busch <kbusch@kernel.org>
Tested-by: John Levon <john.levon@nutanix.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
In case that icdoff is not zero or mandatory keyed sgls are not
supported by the NVMe/RDMA target, we'll go to error flow but we'll
return 0 to the caller. Fix it by returning an appropriate error code.
Fixes: c66e2998c8ca ("nvme-rdma: centralize controller setup sequence")
Signed-off-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
We never checked for errors on add_disk() as this function
returned void. Now that this is fixed, use the shiny new
error handling.
Since we now can tell for sure when a disk was added, move
setting the bit NVME_NSHEAD_DISK_LIVE only when we did
add the disk successfully.
Nothing to do here as the cleanup is done elsewhere. We take
care and use test_and_set_bit() because it is protects against
two nvme paths simultaneously calling device_add_disk() on the
same namespace head.
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
This makes the code more readable.
Signed-off-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
This makes the code more readable.
Signed-off-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
With discovery controllers supporting unique subsystem NQNs the
actual subsystem NQN might be different from that one passed in
via the connect args. So add a helper to display the resulting
subsystem NQN.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Add a connect option 'discovery' to specify that the connection
should be made to a discovery controller, not a normal I/O controller.
With discovery controllers supporting unique subsystem NQNs we
cannot easily distinguish by the subsystem NQN if this should be
a discovery connection, but we need this information to blank out
options not supported by discovery controllers.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
With unique discovery controller NQNs we cannot distinguish the
subsystem type by the NQN alone, but need to check the subsystem
type, too.
So expose the subsystem type in a new sysfs attribute 'subsystype'.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Set the correct 'CNTRLTYPE' field in the identify controller data.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Add a helper function to determine if a given subsystem is a discovery
subsystem.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Update the 'identify controller' structure to define the newly added
CNTRLTYPE field.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
TPAR8013 allows for unique discovery NQNs, so make the discovery
controller NQN configurable by exposing a subsys attribute
'discovery_nqn'.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
