| Age | Commit message (Collapse) | Author |
|---|
|
RK3399-Q7 is a Qseven compatible system-on-module by Theobroma Systems.
This adds the module and the EVK baseboard "Haikou"
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The ROCK64 is a credit card size 4K60P HDR Media Board Computer using the
Rockchip RK3328 Quad-Core ARM Cortex A53 64-Bit Processor and supporting
up to 4GB 1600MHz LPDDR3 memory. It provides eMMC module socket, MicroSD
Card slot, Pi-2 Bus, Pi-P5+ Bus, USB 3.0 and many others peripheral
devices interface for makers to integrate with sensors and devices.
The devicetree currently supports basic peripherals, with more to be
added later on.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
This patch add pdm controller device node for rk3328.
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add VPU/VDEC/IEP/ISP0/ISP1 iommu nodes
Signed-off-by: Simon Xue <xxm@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add IEP/ISP/VOP/HEVC/VPU iommu nodes
Signed-off-by: Simon Xue <xxm@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add H265e/VEPU/VPU/VDEC/VOP iommu nodes
Signed-off-by: Simon Xue <xxm@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
This adds and enable the operating points that have been tested and are
currently supported by the SoC. This also adds clocks for ARMCLKL and
ARMCLKB.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
RK805 consists of 4 DCDCs, 3 LDOs. It's different from RK808
and RK818 that there are 2 output only GPIOs, we should add
properties "gpio-controller" and "gpio-cells = <2>".
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Currently we are assigning mic irq to rt5514 i2c driver, which is wrong.
Assign it to rt5514 spi driver instead.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
We need to init vop aclk and hclk incase the U-Boot does not do
the initialize.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Mark Yao <mark.yao@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
There are 4 pwm channels built in rk3328 soc, need to configure
the both APB clock and bus clock.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
According to rt5514 dt-binding, it should be "realtek,dmic-init-delay-ms".
Fixes: 48f4d9796d99 (arm64: dts: rockchip: add Gru/Kevin DTS)
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
RK3399 USB DWC3 controller has a issue that FS/LS devices not
recognized if inserted through USB 3.0 HUB. It's because that
the inter-packet delay between the SSPLIT token to SETUP token
is about 566ns, more then the USB spec requirement.
This patch adds a quirk "snps,dis-tx-ipgap-linecheck-quirk" to
disable the u2mac linestate check to decrease the SSPLIT token
to SETUP token inter-packet delay from 566ns to 466ns.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
When adding the rk3399 sapphire som, two more of the recently removed
num-slots properties of dw-mmc nodes slipped in.
Remove them again.
Fixes: 8164a84cca12 ("arm64: dts: rockchip: Add support for rk3399 sapphire SOM")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
enable tsadc module on RK3328 eavluation board
Signed-off-by: Rocky Hao <rocky.hao@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
add thermal zone and dynamic CPU power coefficients for rk3328
Signed-off-by: Rocky Hao <rocky.hao@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
add tsadc needed main information for rk3328 SoC.
50000Hz is the max clock rate supported by tsadc module.
Signed-off-by: Rocky Hao <rocky.hao@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
This patch add the i2s dt nodes for rk3328.
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add support for the rk3399 excavator main board.
This board works in a combination with the sapphire SOM.
This board have been sold as the rk3399 evaluation board for commercial customers.
You can get more info from below link:
http://opensource.rock-chips.com/wiki_Excavator_sapphire_board
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add support for the rk3399 sapphire SOM board.
This board works in a combination with the excavator main board.
You can get more info from below link:
http://opensource.rock-chips.com/wiki_Excavator_sapphire_board
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add an hdmi node, and also add hdmi endpoints to vopb and vopl
output port nodes.
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add an mipi node, and also add mipi endpoints to vopb and vopl
output port nodes.
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add an edp node, and also add edp endpoints to vopb and vopl
output port nodes.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
1. add pd node for RK3399 Soc
2. create power domain tree
3. add qos node for domain
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add devicetree nodes for rk3399 VOP (Video Output Processors), and the
top level display-subsystem root node.
Later patches add endpoints (eDP, HDMI, MIPI, etc) that attach to the
VOPs' output ports.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add opp tables for cpu cluster0 and cluster1 by including
rk3399-opp.dtsi.
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
This patch adds basic OPP entries for RK3328 SoC.
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
This patch updates the dynamic-power-coefficient for big cluster on
rk3399 SoCs.
The dynamic power consumption of the CPU is proportional to the square of
the Voltage (V) and the clock frequency (f). The coefficient is used to
calculate the dynamic power as below -
Pdyn = dynamic-power-coefficient * V^2 * f
Where Voltage is in uV, frequency is in MHz.
As the following is the tested data on rk3399's big cluster.
frequency(MHz) Voltage(V) Current(mA) Dynamic-power-coefficient
24 0.8 15
48 0.8 23 ~417
96 0.8 40 ~443
216 0.8 82 ~438
312 0.8 115 ~430
408 0.8 150 ~455
So the dynamic-power-coefficient average value is about 436.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
This patch add the spdif dt node for rk3328.
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
This patch add the spdif dt node for rk3368 soc.
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
This allows basic support for SD highspeed cards but no UHS-I mode
got ready due to the propagated defer-probe error from RK805.
Cc: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add the core grf subnode for the io-domain controller.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Kill these two pinctrl reference totally from rk3399 as it
never work indeed.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
pcie_clkreqn actually doesn't work at all, so replace it with
pcie_clkreqn_cpm.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
This patch enables the gpu and adds the mali-supply power for RK3399-GRU
devices.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add Mali GPU device tree node for the RK3399 SoCs, with devfreq
opp table.
RK3399 and RK3399-OP1 SoCs have a different recommendation table with
gpu opp. Also, the ARM's mali driver found on
https://developer.arm.com/products/software/mali-drivers/midgard-kernel.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
RK3399's GPU uses the quad-core Mali-T860, which is the new generation of
high-end graphics processors from ARM.
This patch added "rockchip,rk3399-mali" for dt-bindings, in order to
support IPA of gpu thermal in later.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
keep-power-in-suspend was invented for SDIO only, so it should
not be used for eMMC node.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
We deprecated the "num-slots" property now and plan to get
rid of it finally. Just move a step to cleanup it from DT.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
pcie_clkreqn actually doesn't work at all, so replace it with
pcie_clkreqn_cpm.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The SdioAudio power domain includes the i2s/spdif/spi5/sdio.
So this patch adds the pd control for rk3399 i2s/spdif/spi5/sdio, in order
to save more power consumption.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Rockchip's RK3328 evaluation board has one usb2 otg controller
and one usb2 host controller which consist of EHCI and OHCI.
Each usb controller connects with one usb2 phy port through
UTMI+ interface. Let's enable them to support usb2 on RK3328
evaluation board.
Signed-off-by: William Wu <william.wu@rock-chips.com>
[restructured enablement of u2phy subnodes]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
This patch adds usb2 otg/host controllers and phys nodes
for Rockchip RK3328 SoCs.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Provide the dynamic power coefficient of the big and little CPU
clusters. These numbers are currently in use on the Samsung Chromebook
Plus ("Kevin").
The power allocator thermal governor doesn't know how to do anything if
it doesn't get power parameters from its cooling devices (in this case,
CPUfreq). So this effectively enables the power-allocator governor.
Signed-off-by: Brian Norris <briannorris@chromium.org>
[set the property in each core node]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The Gru device tree currently contains entries for the regulators
ppvar_bigcpu, ppvar_litcpu, ppvar_gpu and ppvar_centerlogic; however,
the regulators have not been enabled, due to the lack of binding and driver
support for keeping the over-voltage protection (OVP) at bay and
preventing unintended regulator shutdowns on voltage downshifts.
Now, the vctrl regulator driver has been merged, along with new bindings
for asymmetric settling time. The driver is OVP aware, it splits larger
voltage decreases in multiple steps when necessary and adds required
delays.
This change renames each of the aforementioned regulators to
<orig_name>_pwm and adds a new vctrl regulator named <orig_name>.
The vctrl regulators use the voltage of their corresponding PWM regulator
as control voltage. The OVP related values are empirical and stem from
the Chrome OS kernel tree.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
[fixed node names and parent supplies of gpu and centerlogic]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Gru derivatives besides Kevin have slightly different voltage ranges for
their CPU regulators. Let's keep the base Gru file accurate and let
Kevin override.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
replace all occurrences of sdmcc with sdmmc in the arm64 rockchip
devicetree files.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
|
|
Pull documentation format standardization from Jonathan Corbet:
"This series converts a number of top-level documents to the RST format
without incorporating them into the Sphinx tree. The hope is to bring
some uniformity to kernel documentation and, perhaps more importantly,
have our existing docs serve as an example of the desired formatting
for those that will be added later.
Mauro has gone through and fixed up a lot of top-level documentation
files to make them conform to the RST format, but without moving or
renaming them in any way. This will help when we incorporate the ones
we want to keep into the Sphinx doctree, but the real purpose is to
bring a bit of uniformity to our documentation and let the top-level
docs serve as examples for those writing new ones"
* tag 'standardize-docs' of git://git.lwn.net/linux: (84 commits)
docs: kprobes.txt: Fix whitespacing
tee.txt: standardize document format
cgroup-v2.txt: standardize document format
dell_rbu.txt: standardize document format
zorro.txt: standardize document format
xz.txt: standardize document format
xillybus.txt: standardize document format
vfio.txt: standardize document format
vfio-mediated-device.txt: standardize document format
unaligned-memory-access.txt: standardize document format
this_cpu_ops.txt: standardize document format
svga.txt: standardize document format
static-keys.txt: standardize document format
smsc_ece1099.txt: standardize document format
SM501.txt: standardize document format
siphash.txt: standardize document format
sgi-ioc4.txt: standardize document format
SAK.txt: standardize document format
rpmsg.txt: standardize document format
robust-futexes.txt: standardize document format
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull random updates from Ted Ts'o:
"Add wait_for_random_bytes() and get_random_*_wait() functions so that
callers can more safely get random bytes if they can block until the
CRNG is initialized.
Also print a warning if get_random_*() is called before the CRNG is
initialized. By default, only one single-line warning will be printed
per boot. If CONFIG_WARN_ALL_UNSEEDED_RANDOM is defined, then a
warning will be printed for each function which tries to get random
bytes before the CRNG is initialized. This can get spammy for certain
architecture types, so it is not enabled by default"
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
random: reorder READ_ONCE() in get_random_uXX
random: suppress spammy warnings about unseeded randomness
random: warn when kernel uses unseeded randomness
net/route: use get_random_int for random counter
net/neighbor: use get_random_u32 for 32-bit hash random
rhashtable: use get_random_u32 for hash_rnd
ceph: ensure RNG is seeded before using
iscsi: ensure RNG is seeded before use
cifs: use get_random_u32 for 32-bit lock random
random: add get_random_{bytes,u32,u64,int,long,once}_wait family
random: add wait_for_random_bytes() API
|
