| Age | Commit message (Collapse) | Author |
|---|
|
Add DCB support to configure app trust sources and default port priority.
Following commands can be used for testing:
dcb apptrust set dev lan1 order pcp dscp
dcb app replace dev lan1 default-prio 3
Since it is not possible to configure DSCP-Prio mapping per port, this
patch provide only ability to read switch global dscp-prio mapping and
way to enable/disable app trust for DSCP.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
KSZ88X3 switches support up to 4 queues. Rework ksz8795_set_prio_queue()
to support KSZ8795 and KSZ88X3 families of switches.
Per default, configure KSZ88X3 to use one queue, since it need special
handling due to priority related errata. Errata handling is implemented
in a separate patch.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IEEE 802.1q specification provides recommendation and examples which can
be used as good default values for different drivers.
This patch implements mapping examples documented in IEEE 802.1Q-2022 in
Annex I "I.3 Traffic type to traffic class mapping" and IETF DSCP naming
and mapping DSCP to Traffic Type inspired by RFC8325.
This helpers will be used in followup patches for dsa/microchip DCB
implementation.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Most of Microchip KSZ switches use Internal Priority Value associated
with every frame. For example, it is possible to map any VLAN PCP or
DSCP value to IPV and at the end, map IPV to a queue.
Since amount of IPVs is not equal to amount of queues, add this
information and make use of it in some functions.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add DCB support to get/set trust configuration for different packet
priority information sources. Some switch allow to chose different
source of packet priority classification. For example on KSZ switches it
is possible to configure VLAN PCP and/or DSCP sources.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When tmigr_setup_groups() fails the level 0 group allocation, then the
cleanup derefences index -1 of the local stack array.
Prevent this by checking the loop condition first.
Fixes: 7ee988770326 ("timers: Implement the hierarchical pull model")
Signed-off-by: Levi Yun <ppbuk5246@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Link: https://lore.kernel.org/r/20240506041059.86877-1-ppbuk5246@gmail.com
|
|
Use the superblock's UUID to generate the fsid when it's non-null.
Reviewed-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Reviewed-by: Jingbo Xu <jefflexu@linux.alibaba.com>
Signed-off-by: Hongzhen Luo <hongzhen@linux.alibaba.com>
Link: https://lore.kernel.org/r/20240409113022.74720-1-hongzhen@linux.alibaba.com
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
|
|
This adds a special global buffer pool (in the end) for reserved pages.
Using a reserved pool for LZ4 decompression significantly reduces the
time spent on extra temporary page allocation for the extreme cases in
low memory scenarios.
The table below shows the reduction in time spent on page allocation for
LZ4 decompression when using a reserved pool. The results were obtained
from multi-app launch benchmarks on ARM64 Android devices running the
5.15 kernel with an 8-core CPU and 8GB of memory. In the benchmark, we
launched 16 frequently-used apps, and the camera app was the last one in
each round. The data in the table is the average time of camera app for
each round.
After using the reserved pool, there was an average improvement of 150ms
in the overall launch time of our camera app, which was obtained from
the systrace log.
+--------------+---------------+--------------+---------+
| | w/o page pool | w/ page pool | diff |
+--------------+---------------+--------------+---------+
| Average (ms) | 3434 | 21 | -99.38% |
+--------------+---------------+--------------+---------+
Based on the benchmark logs, 64 pages are sufficient for 95% of
scenarios. This value can be adjusted with a module parameter
`reserved_pages`. The default value is 0.
This pool is currently only used for the LZ4 decompressor, but it can be
applied to more decompressors if needed.
Signed-off-by: Chunhai Guo <guochunhai@vivo.com>
Reviewed-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Link: https://lore.kernel.org/r/20240402131523.2703948-1-guochunhai@vivo.com
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
|
|
Let's use alloc_pages_bulk_array() for simplicity and get rid of
unnecessary pagepool.
Signed-off-by: Chunhai Guo <guochunhai@vivo.com>
Reviewed-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Link: https://lore.kernel.org/r/20240402092757.2635257-1-guochunhai@vivo.com
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
|
|
It will cost more time if compressed buffers are allocated on demand for
low-latency algorithms (like lz4) so EROFS uses per-CPU buffers to keep
compressed data if in-place decompression is unfulfilled. While it is kind
of wasteful of memory for a device with hundreds of CPUs, and only a small
number of CPUs concurrently decompress most of the time.
This patch renames it as 'global buffer pool' and makes it configurable.
This allows two or more CPUs to share a common buffer to reduce memory
occupation.
Suggested-by: Gao Xiang <xiang@kernel.org>
Reviewed-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Signed-off-by: Chunhai Guo <guochunhai@vivo.com>
Link: https://lore.kernel.org/r/20240402100036.2673604-1-guochunhai@vivo.com
Signed-off-by: Sandeep Dhavale <dhavale@google.com>
Link: https://lore.kernel.org/r/20240408215231.3376659-1-dhavale@google.com
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
|
|
Currently, utils.c is only useful if CONFIG_EROFS_FS_ZIP is on.
So let's rename it to zutil.c as well as avoid its inclusion if
CONFIG_EROFS_FS_ZIP is explicitly disabled.
Signed-off-by: Chunhai Guo <guochunhai@vivo.com>
Reviewed-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Link: https://lore.kernel.org/r/20240401135550.2550043-1-guochunhai@vivo.com
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
|
|
Add a new EFA flags attribute for QP creation, and support unsolicited
write with immediate flag. QPs created with this flag set will not
consume receive work requests for incoming RDMA write with immediate.
Expose device capability bit for this feature support.
Reviewed-by: Daniel Kranzdorf <dkkranzd@amazon.com>
Reviewed-by: Firas Jahjah <firasj@amazon.com>
Signed-off-by: Michael Margolin <mrgolin@amazon.com>
Link: https://lore.kernel.org/r/20240506151829.6475-1-mrgolin@amazon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
Use of this structure was removed in:
8f2a28c5859b ("perf/x86/cstate: Use new probe function")
Remove the now stale type as well.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: linux-kernel@vger.kernel.org
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
This commit can be considered an addition to commit ca7e324e8ad3
("compiler_types: add Endianness-dependent __counted_by_{le,be}") [1].
In the commit referenced above the __counted_by_{le,be}() attributes
were defined based on platform's endianness with the goal to that the
structures contain flexible arrays at the end, and the counter for,
can be annotated with these attributes.
So, this commit only provide UAPI macros for UAPI structs that will
gain annotations for __counted_by_{le, be} attributes. And it is the
previous step to be able to use these attributes in UAPI.
Link: https://lore.kernel.org/r/20240327142241.1745989-2-aleksander.lobakin@intel.com
Suggested-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Erick Archer <erick.archer@outlook.com>
Link: https://lore.kernel.org/r/AS8PR02MB72372E45071E8821C07236F78BE42@AS8PR02MB7237.eurprd02.prod.outlook.com
Fixes: ca7e324e8ad3 ("compiler_types: add Endianness-dependent __counted_by_{le,be}")
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
This adds support for the FS_IOC_ENABLE_VERITY and FS_IOC_MEASURE_VERITY
ioctls. The FS_IOC_READ_VERITY_METADATA is missing but from the
documentation, "This is a fairly specialized use case, and most fs-verity
users won’t need this ioctl."
Signed-off-by: Richard Fung <richardfung@google.com>
Acked-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
|
|
The internal tag string doesn't contain a newline. Append one when
emitting the tag via sysfs.
[Stefan] Orthogonal to the newline issue, sysfs_emit(buf, "%s", fs->tag) is
needed to prevent format string injection.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Fixes: a8f62f50b4e4 ("virtiofs: export filesystem tags through sysfs")
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
|
|
Nobody checks the error flag on fuse folios, so stop setting it.
Optimise the (optional) setting of the uptodate flag and clearing
of the lock flag by using folio_end_read().
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
|
|
'struct sim_reg_op' wasn't ever used since it was introduced
14 years ago via:
91d8037f563e ("ce4100: Add PCI register emulation for CE4100")
Remove it.
[ mingo: Improved the changelog. ]
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20240507232348.46677-1-linux@treblig.org
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into soc/dt
A few more Qualcomm Arm64 DeviceTree updates for v6.10
This corrects the obviously broken compatible of the USB VBUS regulator
in PM6150.
It clears the odd-looking default address on QCS404 EVB, with the
expectation that a proper address is provides by other means.
The newly added SM8650 GPU node is corrected with a missing memory
region.
The third DWC3 instance on SC8280XP is added, and enabled on Lenovo
Thinkpad X13s to give working fingerprint sensor.
* tag 'qcom-arm64-for-6.10-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
arm64: dts: qcom: pm6150: correct USB VBUS regulator compatible
arm64: dts: qcom: qcs404: fix bluetooth device address
arm64: dts: qcom: sc8280xp-x13s: enable USB MP and fingerprint reader
arm64: dts: qcom: sc8280xp: Add USB DWC3 Multiport controller
arm64: dts: qcom: sm8650: Fix GPU cx_mem size
Link: https://lore.kernel.org/r/20240508021820.206441-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into soc/defconfig
One more Qualcomm Arm64 defconfig update for v6.10
This enables the SM6115 interconnect provider, to make it possible to
boot boards on this SoC.
* tag 'qcom-arm64-defconfig-for-6.10-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
arm64: defconfig: select INTERCONNECT_QCOM_SM6115 as built-in
Link: https://lore.kernel.org/r/20240508021312.206121-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
XSk infra's been using its own DMA sync shortcut to try avoiding
redundant function calls. Now that there is a generic one, remove
the custom implementation and rely on the generic helpers.
xsk_buff_dma_sync_for_cpu() doesn't need the second argument anymore,
remove it.
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
We can save a couple more function calls in the Page Pool code if we
check for dma_need_sync() earlier, just when we test pp->p.dma_sync.
Move both these checks into an inline wrapper and call the PP wrapper
over the generic DMA sync function only when both are true.
You can't cache the result of dma_need_sync() in &page_pool, as it may
change anytime if an SWIOTLB buffer is allocated or mapped.
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into soc/drivers
A few more Qualcomm driver updates for v6.10
This fixes a sleep-while-atomic issue in pmic_glink, stemming from the
fact that the GLINK callback comes from interrupt context.
It fixes the Bluetooth address in the example of qcom,wcnss, and it
enables UEFI variables on SC8180X devices (Primus and Flex 5G).
* tag 'qcom-drivers-for-6.10-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
firmware: qcom: uefisecapp: Allow on sc8180x Primus and Flex 5G
soc: qcom: pmic_glink: Make client-lock non-sleeping
dt-bindings: soc: qcom,wcnss: fix bluetooth address example
Link: https://lore.kernel.org/r/20240508020900.204413-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The early command line parsing treats "kvm-arm.mode=protected" as an
alias for "id_aa64mmfr1.vh=0", forcing the use of nVHE so that the host
kernel runs at EL1 with the pKVM hypervisor at EL2.
With the introduction of hVHE support in ad744e8cb346 ("arm64: Allow
arm64_sw.hvhe on command line"), the hypervisor can run using the EL2+0
translation regime. This is interesting for unusual CPUs that have VH
stuck to 1, but also because it opens the possibility of a hypervisor
"userspace" in the distant future which could be used to isolate vCPU
contexts in the hypervisor (see Marc's talk from KVM Forum 2022 [1]).
Repaint the "kvm-arm.mode=protected" alias to map to "arm64_sw.hvhe=1",
which will use hVHE on CPUs that support it and remain with nVHE
otherwise.
[1] https://www.youtube.com/watch?v=1F_Mf2j9eIo
Signed-off-by: Will Deacon <will@kernel.org>
Acked-by: Oliver Upton <oliver.upton@linux.dev>
Link: https://lore.kernel.org/r/20240501163400.15838-3-will@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
|
|
Booting a kernel with "arm64_sw.hvhe=1 kvm-arm.mode=nvhe" on the
command-line results in KVM initialising using hVHE, whereas one might
expect the latter option to override the former.
Fix this by adding "arm64_sw.hvhe=0" to the alias expansion for
"kvm-arm.mode=nvhe".
Signed-off-by: Will Deacon <will@kernel.org>
Acked-by: Oliver Upton <oliver.upton@linux.dev>
Link: https://lore.kernel.org/r/20240501163400.15838-2-will@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
|
|
of_gpio.h is deprecated and subject to remove.
The driver doesn't use it, simply remove the unused header.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240507205659.690270-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Both dma_unmap_sgtable() and sg_free_table() in spi_unmap_buf_attrs()
have checks for orig_nents against 0. No need to duplicate this.
All the same applies to other DMA mapping API calls.
Also note, there is no other user in the kernel that does this kind of
checks.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240507201028.564630-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
*-objs suffix is reserved rather for (user-space) host programs while
usually *-y suffix is used for kernel drivers (although *-objs works
for that purpose for now).
Let's correct the old usages of *-objs in Makefiles.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20240507155540.24815-35-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
*-objs suffix is reserved rather for (user-space) host programs while
usually *-y suffix is used for kernel drivers (although *-objs works
for that purpose for now).
Let's correct the old usages of *-objs in Makefiles.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20240507155540.24815-34-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
*-objs suffix is reserved rather for (user-space) host programs while
usually *-y suffix is used for kernel drivers (although *-objs works
for that purpose for now).
Let's correct the old usages of *-objs in Makefiles.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20240507155540.24815-33-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
*-objs suffix is reserved rather for (user-space) host programs while
usually *-y suffix is used for kernel drivers (although *-objs works
for that purpose for now).
Let's correct the old usages of *-objs in Makefiles.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20240507155540.24815-32-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
*-objs suffix is reserved rather for (user-space) host programs while
usually *-y suffix is used for kernel drivers (although *-objs works
for that purpose for now).
Let's correct the old usages of *-objs in Makefiles.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20240507155540.24815-31-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
*-objs suffix is reserved rather for (user-space) host programs while
usually *-y suffix is used for kernel drivers (although *-objs works
for that purpose for now).
Let's correct the old usages of *-objs in Makefiles.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20240507155540.24815-30-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
*-objs suffix is reserved rather for (user-space) host programs while
usually *-y suffix is used for kernel drivers (although *-objs works
for that purpose for now).
Let's correct the old usages of *-objs in Makefiles.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20240507155540.24815-29-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
*-objs suffix is reserved rather for (user-space) host programs while
usually *-y suffix is used for kernel drivers (although *-objs works
for that purpose for now).
Let's correct the old usages of *-objs in Makefiles.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20240507155540.24815-28-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
*-objs suffix is reserved rather for (user-space) host programs while
usually *-y suffix is used for kernel drivers (although *-objs works
for that purpose for now).
Let's correct the old usages of *-objs in Makefiles.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20240507155540.24815-27-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
*-objs suffix is reserved rather for (user-space) host programs while
usually *-y suffix is used for kernel drivers (although *-objs works
for that purpose for now).
Let's correct the old usages of *-objs in Makefiles.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20240507155540.24815-26-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
*-objs suffix is reserved rather for (user-space) host programs while
usually *-y suffix is used for kernel drivers (although *-objs works
for that purpose for now).
Let's correct the old usages of *-objs in Makefiles.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20240507155540.24815-25-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
*-objs suffix is reserved rather for (user-space) host programs while
usually *-y suffix is used for kernel drivers (although *-objs works
for that purpose for now).
Let's correct the old usages of *-objs in Makefiles.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20240507155540.24815-24-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
*-objs suffix is reserved rather for (user-space) host programs while
usually *-y suffix is used for kernel drivers (although *-objs works
for that purpose for now).
Let's correct the old usages of *-objs in Makefiles.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20240507155540.24815-23-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
*-objs suffix is reserved rather for (user-space) host programs while
usually *-y suffix is used for kernel drivers (although *-objs works
for that purpose for now).
Let's correct the old usages of *-objs in Makefiles.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20240507155540.24815-22-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
*-objs suffix is reserved rather for (user-space) host programs while
usually *-y suffix is used for kernel drivers (although *-objs works
for that purpose for now).
Let's correct the old usages of *-objs in Makefiles.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20240507155540.24815-21-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
*-objs suffix is reserved rather for (user-space) host programs while
usually *-y suffix is used for kernel drivers (although *-objs works
for that purpose for now).
Let's correct the old usages of *-objs in Makefiles.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20240507155540.24815-20-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
*-objs suffix is reserved rather for (user-space) host programs while
usually *-y suffix is used for kernel drivers (although *-objs works
for that purpose for now).
Let's correct the old usages of *-objs in Makefiles.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20240507155540.24815-19-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
*-objs suffix is reserved rather for (user-space) host programs while
usually *-y suffix is used for kernel drivers (although *-objs works
for that purpose for now).
Let's correct the old usages of *-objs in Makefiles.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20240507155540.24815-18-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
*-objs suffix is reserved rather for (user-space) host programs while
usually *-y suffix is used for kernel drivers (although *-objs works
for that purpose for now).
Let's correct the old usages of *-objs in Makefiles.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20240507155540.24815-17-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
*-objs suffix is reserved rather for (user-space) host programs while
usually *-y suffix is used for kernel drivers (although *-objs works
for that purpose for now).
Let's correct the old usages of *-objs in Makefiles.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20240507155540.24815-16-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
*-objs suffix is reserved rather for (user-space) host programs while
usually *-y suffix is used for kernel drivers (although *-objs works
for that purpose for now).
Let's correct the old usages of *-objs in Makefiles.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20240507155540.24815-15-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
*-objs suffix is reserved rather for (user-space) host programs while
usually *-y suffix is used for kernel drivers (although *-objs works
for that purpose for now).
Let's correct the old usages of *-objs in Makefiles.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20240507155540.24815-14-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
*-objs suffix is reserved rather for (user-space) host programs while
usually *-y suffix is used for kernel drivers (although *-objs works
for that purpose for now).
Let's correct the old usages of *-objs in Makefiles.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20240507155540.24815-13-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
