| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
usb: fixes for v3.7-rc2
Here's the first set of fixes for v3.7-rc cycle.
DesignWare Core USB3 Driver (dwc3) got two fixes. The first one fixes a long
standing bug which would keep endpoint with BUSY flag set forever if we cancel
a transfer which has already been started by the controller. The second fix
will just switch PHYs back off when DWC3 driver is removed.
MUSB fixed a bug which would cause a Kernel Oops at least on AM3517 when
removing a device. For some reason that particular device can fall into a
situation where you have both Disconnect and Endpoint IRQs happen
simultaneously (have both bits set in IRQ_STATUS register) and, because
Disconnect Interrupt is handled before Endpoint Interrupts, we would try to
transfer data over a disconnected device, thus generating a kernel oops.
Renensas' USB DRD driver got two fixes which are a) fixing an off-by-one bug on
the pipe iterator implementation and b) fixing Interrupt Status Clear procedure
in order to properly clear a single Interrupt event without clearing (and
masking) other events we didn't handle yet.
|
|
This minor change adds a new system to which the "Fix Compliance Mode
on SN65LVPE502CP Hardware" patch has to be applied also.
System added:
Vendor: Hewlett-Packard. System Model: Z1
Signed-off-by: Alexis R. Cortes <alexis.cortes@ti.com>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make sure port data is initialised before creating sysfs attributes to
avoid a race.
A recent patch ("USB: io_ti: fix port-data memory leak") got the
sysfs-attribute creation and port-data initialisation ordering wrong.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make sure sysfs attributes are created at port probe.
A recent patch ("USB: iuu_phoenix: fix port-data memory leak") removed
the sysfs-attribute creation by mistake.
Reported-by: Yuanhan Liu <yuanhan.liu@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix port-data memory leak by replacing attach and release with
port_probe and port_remove.
Since commit 0998d0631001288 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix port-data memory leak by replacing attach and release with
port_probe and port_remove.
Since commit 0998d0631001288 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix port-data memory leak by moving port data allocation and
deallocation to port_probe and port_remove.
Since commit 0998d0631001288 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix port-data memory leak by replacing attach and release with
port_probe and port_remove.
Since commit 0998d0631001288 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix port-data memory leak by replacing attach and release with
port_probe and port_remove.
Since commit 0998d0631001288 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix port-data memory leak by replacing attach and release with
port_probe and port_remove.
Since commit 0998d0631001288 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Note that the write waitqueue was initialised but never used.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix port-data memory leak by moving port data allocation and
deallocation to port_probe and port_remove.
Since commit 0998d0631001288 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix port-data memory leak by replacing attach and release with
port_probe and port_remove.
Since commit 0998d0631001288 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Note that the write waitqueue was initialised but never used.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix port-data memory leak by replacing attach and release with
port_probe and port_remove.
Since commit 0998d0631001288 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix port-data memory leak by moving port data allocation and
deallocation to port_probe and port_remove.
Since commit 0998d0631001288 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix port-data memory leak by replacing attach and release with
port_probe and port_remove.
Since commit 0998d0631001288 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix port-data memory leak by replacing attach and release with
port_probe and port_remove.
Since commit 0998d0631001288 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The current code assumes that CSIZE is 0000060, which appears to be
wrong on some arches (such as powerpc).
Signed-off-by: Nicolas Boullis <nboullis@debian.org>
Acked-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Device-tree probed devices don't get a dev.dma_mask set. This patch
sets a default 32bit mask on arch-vt8500 when using devicetree.
Without this patch, arch-vt8500 cannot detect ehci attached devices.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Device-tree probed devices don't get a dev.dma_mask set. This patch
sets a default 32bit mask on platforms using devicetree.
Without this patch, arch-vt8500 cannot detect uhci attached devices.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If the write endpoint is interrupt type, usb_sndintpipe() should
be passed to usb_fill_int_urb() instead of usb_sndbulkpipe().
Cc: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The handling of large output bulk transfers is broken; the same user
page is read over and over again. Fixed with this patch.
Cc: stable <stable@vger.kernel.org>
Acked-by: Peter Stuge <peter@stuge.se>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There are no users of this macro anymore in the kernel tree, so finally
delete it.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch (as1615) fixes a bug in the Garmin USB serial driver. It
uses attach, disconnect, and release routines to carry out actions
that should be handled by port_probe and port_remove routines, because
they access port-specific data.
The bug causes an oops when the device in unplugged, because the
private data for each port structure now gets erased when the port is
unbound from the driver, resulting in a null-pointer dereference.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported--by: Markus Schauler <mschauler@gmail.com>
Tested-by: Markus Schauler <mschauler@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix port-data memory leak by allocating and freeing port data in
port_probe/remove rather than in attach/release, and by introducing
serial private data to store the device type which is interface rather
than port specific.
Since commit 0998d0631001288 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix port data memory leak by replacing port private data with serial
private data.
Since commit 0998d0631001288 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at
release.
The private data is used to store the control interface number, but as
this is the same for all ports on an interface it should be stored as
usb-serial data anyway.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix port-data memory leak by replacing attach and release with
port_probe and port_remove.
Since commit 0998d0631001288 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Note that the write waitqueue was initialised but never used.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix port-data memory leak by replacing attach and release with
port_probe and port_remove.
Since commit 0998d0631001288 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Note that the write waitqueue was initialised but never used.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix NULL-pointer dereference at release by replacing attach and release
with port_probe and port_remove.
Since commit 0998d0631001288 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is NULL when release is called.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The STOTG04 is an replacement for ISP1301.
Most of the registers on STOTG04 are the same as on ISP1301, but the
register ISP1301_I2C_OTG_CONTROL_2 (address 0x10) doesn't exist on the
ST part.
This is a work around for this by using the interrupt source register that
should behave the same on both parts and has the needed information.
Tested-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
When interrupt happened, renesas_usbhs driver gets irq status
by usbhs_status_get_each_irq(), and cleared all status by using 0.
But, this method is incorrect,
since extra interrupt might occur between them.
This patch cleared corresponding bits only
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
__usbhs_for_each_pipe() is the macro which moves around each pipe,
but it has a bug which didn't care about 1st pipe's position.
Because of this bug, it moves around
pipe0, pipe2, pipe3 ... even though it requested pipe1, pipe2, pipe3...
This patch modifies it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Composite gadget support is now available as a library instead of being
built with each gadget. Composite drivers need to select
USB_LIBCOMPOSITE.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We call usb_phy_init() from dwc3_core_init() during
probe, so adding usb_phy_shutdown() to dwc3_core_exit()
while removing the device so we don't keep PHYs
turned on, consuming power, unnecessarily.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
On AM3517, tx and rx interrupt are detected together with
the disconnect event. This generates a kernel panic in musb_interrupt,
because rx / tx are handled after disconnect.
This issue was seen on a Technexion's TAM3517 SOM. Unplugging a device,
tx / rx interrupts together with disconnect are detected. This brings
to kernel panic like this:
[ 68.526153] Unable to handle kernel NULL pointer dereference at virtual address 00000011
[ 68.534698] pgd = c0004000
[ 68.537536] [00000011] *pgd=00000000
[ 68.541351] Internal error: Oops: 17 [#1] ARM
[ 68.545928] Modules linked in:
[ 68.549163] CPU: 0 Not tainted (3.6.0-rc5-00020-g9e05905 #178)
[ 68.555694] PC is at rxstate+0x8/0xdc
[ 68.559539] LR is at musb_interrupt+0x98/0x858
[ 68.564239] pc : [<c035cd88>] lr : [<c035af1c>] psr: 40000193
[ 68.564239] sp : ce83fb40 ip : d0906410 fp : 00000000
[ 68.576293] r10: 00000000 r9 : cf3b0e40 r8 : 00000002
[ 68.581817] r7 : 00000019 r6 : 00000001 r5 : 00000001 r4 : 000000d4
[ 68.588684] r3 : 00000000 r2 : 00000000 r1 : ffffffcc r0 : cf23c108
[ 68.595550] Flags: nZcv IRQs off FIQs on Mode SVC_32 ISA ARM Segment ke
Note: this behavior is not seen with a USB hub, while it is
easy to reproduce connecting a USB-pen directly to the USB-A of
the board.
Drop tx / rx interrupts if disconnect is detected.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Felipe Balbi <balbi@ti.com>
Cc: stable@vger.kernel.org # 3.5 3.6
Tested-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Tested-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
If a USB transfer has already been started, meaning
we have already issued StartTransfer command to that
particular endpoint, DWC3_EP_BUSY flag has also
already been set.
When we try to cancel this transfer which is already
in controller's cache, we will not receive XferComplete
event and we must clear DWC3_EP_BUSY in order to allow
subsequent requests to be properly started.
The best place to clear that flag is right after issuing
DWC3_DEPCMD_ENDTRANSFER.
Cc: stable@vger.kernel.org # v3.4 v3.5 v3.6
Reported-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Sync up to a known-good point in Linus's tree to build on.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
|
|
Pull MIPS update from Ralf Baechle:
"Cleanups and fixes for breakage that occured earlier during this merge
phase. Also a few patches that didn't make the first pull request.
Of those is the Alchemy work that merges code for many of the SOCs and
evaluation boards thus among other code shrinkage, reduces the number
of MIPS defconfigs by 5."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (22 commits)
MIPS: SNI: Switch RM400 serial to SCCNXP driver
MIPS: Remove unused empty_bad_pmd_table[] declaration.
MIPS: MT: Remove kspd.
MIPS: Malta: Fix section mismatch.
MIPS: asm-offset.c: Delete unused irq_cpustat_t struct offsets.
MIPS: Alchemy: Merge PB1100/1500 support into DB1000 code.
MIPS: Alchemy: merge PB1550 support into DB1550 code
MIPS: Alchemy: Single kernel for DB1200/1300/1550
MIPS: Optimize TLB refill for RI/XI configurations.
MIPS: proc: Cleanup printing of ASEs.
MIPS: Hardwire detection of DSP ASE Rev 2 for systems, as required.
MIPS: Add detection of DSP ASE Revision 2.
MIPS: Optimize pgd_init and pmd_init
MIPS: perf: Add perf functionality for BMIPS5000
MIPS: perf: Split the Kconfig option CONFIG_MIPS_MT_SMP
MIPS: perf: Remove unnecessary #ifdef
MIPS: perf: Add cpu feature bit for PCI (performance counter interrupt)
MIPS: perf: Change the "mips_perf_event" table unsupported indicator.
MIPS: Align swapper_pg_dir to 64K for better TLB Refill code.
vmlinux.lds.h: Allow architectures to add sections to the front of .bss
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module signing support from Rusty Russell:
"module signing is the highlight, but it's an all-over David Howells frenzy..."
Hmm "Magrathea: Glacier signing key". Somebody has been reading too much HHGTTG.
* 'modules-next' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (37 commits)
X.509: Fix indefinite length element skip error handling
X.509: Convert some printk calls to pr_devel
asymmetric keys: fix printk format warning
MODSIGN: Fix 32-bit overflow in X.509 certificate validity date checking
MODSIGN: Make mrproper should remove generated files.
MODSIGN: Use utf8 strings in signer's name in autogenerated X.509 certs
MODSIGN: Use the same digest for the autogen key sig as for the module sig
MODSIGN: Sign modules during the build process
MODSIGN: Provide a script for generating a key ID from an X.509 cert
MODSIGN: Implement module signature checking
MODSIGN: Provide module signing public keys to the kernel
MODSIGN: Automatically generate module signing keys if missing
MODSIGN: Provide Kconfig options
MODSIGN: Provide gitignore and make clean rules for extra files
MODSIGN: Add FIPS policy
module: signature checking hook
X.509: Add a crypto key parser for binary (DER) X.509 certificates
MPILIB: Provide a function to read raw data into an MPI
X.509: Add an ASN.1 decoder
X.509: Add simple ASN.1 grammar compiler
...
|
|
The hostprogs need access to the CONFIG_* symbols found in
include/generated/autoconf.h. But commit abbf1590de22 ("UAPI: Partition
the header include path sets and add uapi/ header directories") replaced
$(LINUXINCLUDE) with $(USERINCLUDE) which doesn't contain the necessary
include paths.
This has the undesirable effect of breaking the EFI boot stub because
the #ifdef CONFIG_EFI_STUB code in arch/x86/boot/tools/build.c is
never compiled.
It should also be noted that because $(USERINCLUDE) isn't exported by
the top-level Makefile it's actually empty in arch/x86/boot/Makefile.
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@kernel.org>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The UAPI commits forgot to test tooling builds such as tools/perf/,
and this fixes the fallout.
Manual conversion.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull ARM update from Russell King:
"This is the final round of stuff for ARM, left until the end of the
merge window to reduce the number of conflicts. This set contains the
ARM part of David Howells UAPI changes, and a fix to the ordering of
'select' statements in ARM Kconfig files (see the appropriate commit
for why this happened - thanks to Andrew Morton for pointing out the
problem.)
I've left this as long as I dare for this window to avoid conflicts,
and I regenerated the config patch yesterday, posting it to our
mailing list for review and testing. I have several acks which
include successful test reports for it.
However, today I notice we've got new conflicts with previously unseen
code... though that conflict should be trivial (it's my changes vs a
one liner.)"
* 'late-for-linus' of git://git.linaro.org/people/rmk/linux-arm:
ARM: config: make sure that platforms are ordered by option string
ARM: config: sort select statements alphanumerically
UAPI: (Scripted) Disintegrate arch/arm/include/asm
Fix up fairly conflict in arch/arm/Kconfig (the select re-organization
vs recent addition of GENERIC_KERNEL_EXECVE)
|
|
git://git.infradead.org/users/dhowells/linux-headers into usb-linus
UAPI Disintegration 2012-10-09
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus
USB 3.0 Link PM fixes.
Hi Greg,
Here's four fixes for the USB 3.0 Link Power Management code. They
work around some USB 3.0 devices that don't support LPM, like the
Western Digital My Passport hard drive. They also fix an LPM disable
ref count bug that would cause LPM to remain disabled for a device
after a failed probe.
Please queue for 3.7 after the merge window closes. Several patches are
marked for stable.
Sarah Sharp
|
|
git://git.infradead.org/users/dhowells/linux-headers
Pull UAPI disintegration for include/linux/{,byteorder/}*.h from David Howells:
"The patches contained herein do the following:
(1) Remove kernel-only stuff in linux/ppp-comp.h from the UAPI. I checked
this with Paul Mackerras before I created the patch and he suggested some
extra bits to unexport.
(2) Remove linux/blk_types.h entirely from the UAPI as none of it is userspace
applicable, and remove from the UAPI that part of linux/fs.h that was the
reason for linux/blk_types.h being exported in the first place. I
discussed this with Jens Axboe before creating the patch.
(3) The big patch of the series to disintegrate include/linux/*.h as a unit.
This could be split up, though there would be collisions in moving stuff
between the two Kbuild files when the parts are merged as that file is
sorted alphabetically rather than being grouped by subsystem.
Of this set of headers, 17 files have changed in the UAPI exported region
since the 4th and only 8 since the 9th so there isn't much change in this
area - as one might expect.
It should be pretty obvious and straightforward if it does come to fixing
up: stuff in __KERNEL__ guards stays where it is and stuff outside moves
to the same file in the include/uapi/linux/ directory.
If a new file appears then things get a bit more complicated as the
"headers +=" line has to move to include/uapi/linux/Kbuild. Only one new
file has appeared since the 9th and I judge this type of event relatively
unlikely.
(4) A patch to disintegrate include/linux/byteorder/*.h as a unit.
Signed-off-by: David Howells <dhowells@redhat.com>"
* tag 'disintegrate-main-20121013' of git://git.infradead.org/users/dhowells/linux-headers:
UAPI: (Scripted) Disintegrate include/linux/byteorder
UAPI: (Scripted) Disintegrate include/linux
UAPI: Unexport linux/blk_types.h
UAPI: Unexport part of linux/ppp-comp.h
|
|
git://git.infradead.org/users/dhowells/linux-headers
Pull spi UAPI disintegration from David Howells:
"This is to complete part of the Userspace API (UAPI) disintegration
for which the preparatory patches were pulled recently. After these
patches, userspace headers will be segregated into:
include/uapi/linux/.../foo.h
for the userspace interface stuff, and:
include/linux/.../foo.h
for the strictly kernel internal stuff.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>"
* tag 'disintegrate-spi-20121009' of git://git.infradead.org/users/dhowells/linux-headers:
UAPI: (Scripted) Disintegrate include/linux/spi
|
|
Pull OpenRISC uapi disintegration from Jonas Bonn:
"OpenRISC UAPI disintegration work from David Howells"
* tag 'openrisc-uapi' of git://openrisc.net/jonas/linux:
UAPI: (Scripted) Disintegrate arch/openrisc/include/asm
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull user namespace compile fixes from Eric W Biederman:
"This tree contains three trivial fixes. One compiler warning, one
thinko fix, and one build fix"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
btrfs: Fix compilation with user namespace support enabled
userns: Fix posix_acl_file_xattr_userns gid conversion
userns: Properly print bluetooth socket uids
|
|
Pull md updates from NeilBrown:
- "discard" support, some dm-raid improvements and other assorted bits
and pieces.
* tag 'md-3.7' of git://neil.brown.name/md: (29 commits)
md: refine reporting of resync/reshape delays.
md/raid5: be careful not to resize_stripes too big.
md: make sure manual changes to recovery checkpoint are saved.
md/raid10: use correct limit variable
md: writing to sync_action should clear the read-auto state.
Subject: [PATCH] md:change resync_mismatches to atomic64_t to avoid races
md/raid5: make sure to_read and to_write never go negative.
md: When RAID5 is dirty, force reconstruct-write instead of read-modify-write.
md/raid5: protect debug message against NULL derefernce.
md/raid5: add some missing locking in handle_failed_stripe.
MD: raid5 avoid unnecessary zero page for trim
MD: raid5 trim support
md/bitmap:Don't use IS_ERR to judge alloc_page().
md/raid1: Don't release reference to device while handling read error.
raid: replace list_for_each_continue_rcu with new interface
add further __init annotations to crypto/xor.c
DM RAID: Fix for "sync" directive ineffectiveness
DM RAID: Fix comparison of index and quantity for "rebuild" parameter
DM RAID: Add rebuild capability for RAID10
DM RAID: Move 'rebuild' checking code to its own function
...
|
