summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2020-01-21net: hns3: do not reuse pfmemalloc pagesYunsheng Lin
HNS3 driver allocates pages for DMA with dev_alloc_pages(), which calls alloc_pages_node() with the __GFP_MEMALLOC flag. So, in case of OOM condition, HNS3 can get pages with pfmemalloc flag set. So do not reuse the pages with pfmemalloc flag set because those pages are reserved for special cases, such as low memory case. Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-21net: hns3: limit the error logging in the hns3_clean_tx_ring()Yunsheng Lin
The error log printed by netdev_err() in the hns3_clean_tx_ring() may spam the kernel log. This patch uses hns3_rl_err() to ratelimit the error log in the hns3_clean_tx_ring(). Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-21wan/hdlc_x25: fix skb handlingMartin Schiller
o call skb_reset_network_header() before hdlc->xmit() o change skb proto to HDLC (0x0019) before hdlc->xmit() o call dev_queue_xmit_nit() before hdlc->xmit() This changes make it possible to trace (tcpdump) outgoing layer2 (ETH_P_HDLC) packets Additionally call skb_reset_network_header() after each skb_push() / skb_pull(). Signed-off-by: Martin Schiller <ms@dev.tdt.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-21wan/hdlc_x25: make lapb params configurableMartin Schiller
This enables you to configure mode (DTE/DCE), Modulo, Window, T1, T2, N2 via sethdlc (which needs to be patched as well). Signed-off-by: Martin Schiller <ms@dev.tdt.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-21net/smc: allow unprivileged users to read pnet tableHans Wippel
The current flags of the SMC_PNET_GET command only allow privileged users to retrieve entries from the pnet table via netlink. The content of the pnet table may be useful for all users though, e.g., for debugging smc connection problems. This patch removes the GENL_ADMIN_PERM flag so that unprivileged users can read the pnet table. Signed-off-by: Hans Wippel <ndev@hwipl.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-21arm64: entry: Avoid empty alternatives entriesJulien Thierry
kernel_ventry will create alternative entries to potentially replace 0 instructions with 0 instructions for EL1 vectors. While this does not cause an issue, it pointlessly takes up some bytes in the alternatives section. Do not generate such entries. Acked-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Julien Thierry <jthierry@redhat.com> Signed-off-by: Will Deacon <will@kernel.org>
2020-01-21tcp: remove redundant assigment to snd_cwndTheodore Dubois
Not sure how this got in here. git blame says the second assignment was added in 3a9a57f6, but that commit also removed the first assignment. Signed-off-by: Theodore Dubois <tblodt@icloud.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-21Merge branch 'phy-add-new-version-of-phy_do_ioctl-and-convert-suitable-drivers'David S. Miller
Heiner Kallweit says: ==================== net: phy: add new version of phy_do_ioctl and convert suitable drivers We just added phy_do_ioctl, but it turned out that we need another version of this function that doesn't check whether net_device is running. So rename phy_do_ioctl to phy_do_ioctl_running and add a new version of phy_do_ioctl. Eventually convert suitable drivers to use phy_do_ioctl. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-21net: convert suitable network drivers to use phy_do_ioctlHeiner Kallweit
Convert suitable network drivers to use phy_do_ioctl. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-21net: phy: add new version of phy_do_ioctlHeiner Kallweit
Add a new version of phy_do_ioctl that doesn't check whether net_device is running. It will typically be used if suitable drivers attach the PHY in probe already. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-21net: phy: rename phy_do_ioctl to phy_do_ioctl_runningHeiner Kallweit
We just added phy_do_ioctl, but it turned out that we need another version of this function that doesn't check whether net_device is running. So rename phy_do_ioctl to phy_do_ioctl_running. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-21net: hns3: replace snprintf with scnprintf in hns3_update_stringsChen Zhou
snprintf returns the number of bytes that would be written, which may be greater than the the actual length to be written. Here use extra code to handle this. scnprintf returns the number of bytes that was actually written, just use scnprintf to simplify the code. Signed-off-by: Chen Zhou <chenzhou10@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-21net: hns3: replace snprintf with scnprintf in hns3_dbg_cmd_readChen Zhou
The return value of snprintf may be greater than the size of HNS3_DBG_READ_LEN, use scnprintf instead in hns3_dbg_cmd_read. Signed-off-by: Chen Zhou <chenzhou10@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-21net: usb: lan78xx: Add .ndo_features_checkJames Hughes
As reported by Eric Dumazet, there are still some outstanding cases where the driver does not handle TSO correctly when skb's are over a certain size. Most cases have been fixed, this patch should ensure that forwarded SKB's that are greater than MAX_SINGLE_PACKET_SIZE - TX_OVERHEAD are software segmented and handled correctly. Signed-off-by: James Hughes <james.hughes@raspberrypi.org> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-21tcp_bbr: improve arithmetic division in bbr_update_bw()Wen Yang
do_div() does a 64-by-32 division. Use div64_long() instead of it if the divisor is long, to avoid truncation to 32-bit. And as a nice side effect also cleans up the function a bit. Signed-off-by: Wen Yang <wenyang@linux.alibaba.com> Cc: Eric Dumazet <edumazet@google.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru> Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org> Cc: netdev@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-21net-sysfs: Fix reference count leakJouni Hogander
Netdev_register_kobject is calling device_initialize. In case of error reference taken by device_initialize is not given up. Drivers are supposed to call free_netdev in case of error. In non-error case the last reference is given up there and device release sequence is triggered. In error case this reference is kept and the release sequence is never started. Fix this by setting reg_state as NETREG_UNREGISTERED if registering fails. This is the rootcause for couple of memory leaks reported by Syzkaller: BUG: memory leak unreferenced object 0xffff8880675ca008 (size 256): comm "netdev_register", pid 281, jiffies 4294696663 (age 6.808s) hex dump (first 32 bytes): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ backtrace: [<0000000058ca4711>] kmem_cache_alloc_trace+0x167/0x280 [<000000002340019b>] device_add+0x882/0x1750 [<000000001d588c3a>] netdev_register_kobject+0x128/0x380 [<0000000011ef5535>] register_netdevice+0xa1b/0xf00 [<000000007fcf1c99>] __tun_chr_ioctl+0x20d5/0x3dd0 [<000000006a5b7b2b>] tun_chr_ioctl+0x2f/0x40 [<00000000f30f834a>] do_vfs_ioctl+0x1c7/0x1510 [<00000000fba062ea>] ksys_ioctl+0x99/0xb0 [<00000000b1c1b8d2>] __x64_sys_ioctl+0x78/0xb0 [<00000000984cabb9>] do_syscall_64+0x16f/0x580 [<000000000bde033d>] entry_SYSCALL_64_after_hwframe+0x44/0xa9 [<00000000e6ca2d9f>] 0xffffffffffffffff BUG: memory leak unreferenced object 0xffff8880668ba588 (size 8): comm "kobject_set_nam", pid 286, jiffies 4294725297 (age 9.871s) hex dump (first 8 bytes): 6e 72 30 00 cc be df 2b nr0....+ backtrace: [<00000000a322332a>] __kmalloc_track_caller+0x16e/0x290 [<00000000236fd26b>] kstrdup+0x3e/0x70 [<00000000dd4a2815>] kstrdup_const+0x3e/0x50 [<0000000049a377fc>] kvasprintf_const+0x10e/0x160 [<00000000627fc711>] kobject_set_name_vargs+0x5b/0x140 [<0000000019eeab06>] dev_set_name+0xc0/0xf0 [<0000000069cb12bc>] netdev_register_kobject+0xc8/0x320 [<00000000f2e83732>] register_netdevice+0xa1b/0xf00 [<000000009e1f57cc>] __tun_chr_ioctl+0x20d5/0x3dd0 [<000000009c560784>] tun_chr_ioctl+0x2f/0x40 [<000000000d759e02>] do_vfs_ioctl+0x1c7/0x1510 [<00000000351d7c31>] ksys_ioctl+0x99/0xb0 [<000000008390040a>] __x64_sys_ioctl+0x78/0xb0 [<0000000052d196b7>] do_syscall_64+0x16f/0x580 [<0000000019af9236>] entry_SYSCALL_64_after_hwframe+0x44/0xa9 [<00000000bc384531>] 0xffffffffffffffff v3 -> v4: Set reg_state to NETREG_UNREGISTERED if registering fails v2 -> v3: * Replaced BUG_ON with WARN_ON in free_netdev and netdev_release v1 -> v2: * Relying on driver calling free_netdev rather than calling put_device directly in error path Reported-by: syzbot+ad8ca40ecd77896d51e2@syzkaller.appspotmail.com Cc: David Miller <davem@davemloft.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Lukas Bulwahn <lukas.bulwahn@gmail.com> Signed-off-by: Jouni Hogander <jouni.hogander@unikie.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-21dmaengine: Move dma_get_{,any_}slave_channel() to private dmaengine.hGeert Uytterhoeven
The functions dma_get_slave_channel() and dma_get_any_slave_channel() are called from DMA engine drivers only. Hence move their declarations from the public header file <linux/dmaengine.h> to the private header file drivers/dma/dmaengine.h. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Arnd Bergmann <arnd@arndb.de> Link: https://lore.kernel.org/r/20200121093311.28639-4-geert+renesas@glider.be Signed-off-by: Vinod Koul <vkoul@kernel.org>
2020-01-21dmaengine: Remove dma_request_slave_channel_compat() wrapperGeert Uytterhoeven
At its original introduction, dma_request_slave_channel_compat() used a wrapper, to accommodate filter functions that modify the mask passed. Filter functions can no longer modify masks, and the mask parameter was made const in commit a53e28da574a40bc ("dma: Make the 'mask' parameter of __dma_request_channel const") consecutively. Hence remove the wrapper, and rename __dma_request_slave_channel_compat() to dma_request_slave_channel_compat(), to get rid of one more function name starting with a double underscore. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Arnd Bergmann <arnd@arndb.de> Link: https://lore.kernel.org/r/20200121093311.28639-3-geert+renesas@glider.be Signed-off-by: Vinod Koul <vkoul@kernel.org>
2020-01-21dmaengine: Remove dma_device_satisfies_mask() wrapperGeert Uytterhoeven
Commit aa1e6f1a385eb2b0 ("dmaengine: kill struct dma_client and supporting infrastructure") removed the last user of the dma_device_satisfies_mask() wrapper. Remove the wrapper, and rename __dma_device_satisfies_mask() to dma_device_satisfies_mask(), to get rid of one more function starting with a double underscore. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Arnd Bergmann <arnd@arndb.de> Link: https://lore.kernel.org/r/20200121093311.28639-2-geert+renesas@glider.be Signed-off-by: Vinod Koul <vkoul@kernel.org>
2020-01-21Merge tag 'rds-odp-for-5.5' of ↵David S. Miller
https://git.kernel.org/pub/scm/linux/kernel/git/leon/linux-rdma Leon Romanovsky says: ==================== Use ODP MRs for kernel ULPs The following series extends MR creation routines to allow creation of user MRs through kernel ULPs as a proxy. The immediate use case is to allow RDS to work over FS-DAX, which requires ODP (on-demand-paging) MRs to be created and such MRs were not possible to create prior this series. The first part of this patchset extends RDMA to have special verb ib_reg_user_mr(). The common use case that uses this function is a userspace application that allocates memory for HCA access but the responsibility to register the memory at the HCA is on an kernel ULP. This ULP acts as an agent for the userspace application. The second part provides advise MR functionality for ULPs. This is integral part of ODP flows and used to trigger pagefaults in advance to prepare memory before running working set. The third part is actual user of those in-kernel APIs. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-21dt-bindings: fsl-imx-sdma: Add i.MX8MM/i.MX8MN/i.MX8MP compatible stringAnson Huang
Add imx8mm/imx8mn/imx8mp sdma support. Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Acked-by: Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/1578893602-14395-1-git-send-email-Anson.Huang@nxp.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
2020-01-21dmaengine: zynqmp_dma: fix burst length configurationMatthias Fend
Since the dma engine expects the burst length register content as power of 2 value, the burst length needs to be converted first. Additionally add a burst length range check to avoid corrupting unrelated register bits. Signed-off-by: Matthias Fend <matthias.fend@wolfvision.net> Link: https://lore.kernel.org/r/20200115102249.24398-1-matthias.fend@wolfvision.net Signed-off-by: Vinod Koul <vkoul@kernel.org>
2020-01-21ipv6: sr: remove SKB_GSO_IPXIP6 on End.D* actionsYuki Taguchi
After LRO/GRO is applied, SRv6 encapsulated packets have SKB_GSO_IPXIP6 feature flag, and this flag must be removed right after decapulation procedure. Currently, SKB_GSO_IPXIP6 flag is not removed on End.D* actions, which creates inconsistent packet state, that is, a normal TCP/IP packets have the SKB_GSO_IPXIP6 flag. This behavior can cause unexpected fallback to GSO on routing to netdevices that do not support SKB_GSO_IPXIP6. For example, on inter-VRF forwarding, decapsulated packets separated into small packets by GSO because VRF devices do not support TSO for packets with SKB_GSO_IPXIP6 flag, and this degrades forwarding performance. This patch removes encapsulation related GSO flags from the skb right after the End.D* action is applied. Fixes: d7a669dd2f8b ("ipv6: sr: add helper functions for seg6local") Signed-off-by: Yuki Taguchi <tagyounit@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-21arm64: Kconfig: select HAVE_FUTEX_CMPXCHGVladimir Murzin
arm64 provides always working implementation of futex_atomic_cmpxchg_inatomic(), so there is no need to check it runtime. Reported-by: Piyush swami <Piyush.swami@arm.com> Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com> Signed-off-by: Will Deacon <will@kernel.org>
2020-01-21dmaengine: sun4i: Add support for cyclic requests with dedicated DMAStefan Mavrodiev
Currently the cyclic transfers can be used only with normal DMAs. They can be used by pcm_dmaengine module, which is required for implementing sound with sun4i-hdmi encoder. This is so because the controller can accept audio only from a dedicated DMA. This patch enables them, following the existing style for the scatter/gather type transfers. Signed-off-by: Stefan Mavrodiev <stefan@olimex.com> Acked-by: Maxime Ripard <mripard@kernel.org> Link: https://lore.kernel.org/r/20200110141140.28527-2-stefan@olimex.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
2020-01-21Merge branch 'master' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec Steffen Klassert says: ==================== pull request (net): ipsec 2020-01-21 1) Fix packet tx through bpf_redirect() for xfrm and vti interfaces. From Nicolas Dichtel. 2) Do not confirm neighbor when do pmtu update on a virtual xfrm interface. From Xu Wang. 3) Support output_mark for offload ESP packets, this was forgotten when the output_mark was added initially. From Ulrich Weber. Please pull or let me know if there are problems. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-21dmaengine: fsl-qdma: fix duplicated argument to &&Chen Zhou
There is duplicated argument to && in function fsl_qdma_free_chan_resources, which looks like a typo, pointer fsl_queue->desc_pool also needs NULL check, fix it. Detected with coccinelle. Fixes: b092529e0aa0 ("dmaengine: fsl-qdma: Add qDMA controller driver for Layerscape SoCs") Signed-off-by: Chen Zhou <chenzhou10@huawei.com> Reviewed-by: Peng Ma <peng.ma@nxp.com> Tested-by: Peng Ma <peng.ma@nxp.com> Link: https://lore.kernel.org/r/20200120125843.34398-1-chenzhou10@huawei.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
2020-01-21dmaengine: ti: k3-psil: make symbols staticPeter Ujfalusi
Fixe the following warnings by making these static drivers/dma/ti/k3-psil-j721e.c:62:16: warning: symbol 'j721e_src_ep_map' was not declared. Should it be static? drivers/dma/ti/k3-psil-j721e.c:172:16: warning: symbol 'j721e_dst_ep_map' was not declared. Should it be static? drivers/dma/ti/k3-psil-j721e.c:216:20: warning: symbol 'j721e_ep_map' was not declared. Should it be static? CC drivers/dma/ti/k3-psil-j721e.o drivers/dma/ti/k3-psil-am654.c:52:16: warning: symbol 'am654_src_ep_map' was not declared. Should it be static? drivers/dma/ti/k3-psil-am654.c:127:16: warning: symbol 'am654_dst_ep_map' was not declared. Should it be static? drivers/dma/ti/k3-psil-am654.c:169:20: warning: symbol 'am654_ep_map' was not declared. Should it be static? Reported-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Link: https://lore.kernel.org/r/20200121070104.4393-1-peter.ujfalusi@ti.com [vkoul: updated patch title] Signed-off-by: Vinod Koul <vkoul@kernel.org>
2020-01-21drm/i915: Align engine->uabi_class/instance with i915_drm.hTvrtko Ursulin
In our ABI we have defined I915_ENGINE_CLASS_INVALID_NONE and I915_ENGINE_CLASS_INVALID_VIRTUAL as negative values which creates implicit coupling with type widths used in, also ABI, struct i915_engine_class_instance. One place where we export engine->uabi_class I915_ENGINE_CLASS_INVALID_VIRTUAL is from our our tracepoints. Because the type of the former is u8 in contrast to u16 defined in the ABI, 254 will be returned instead of 65534 which userspace would legitimately expect. Another place is I915_CONTEXT_PARAM_ENGINES. Therefore we need to align the type used to store engine ABI class and instance. v2: * Update the commit message mentioning get_engines and cc stable. (Chris) Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Fixes: 6d06779e8672 ("drm/i915: Load balancing across a virtual engine") Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: <stable@vger.kernel.org> # v5.3+ Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20200116134508.25211-1-tvrtko.ursulin@linux.intel.com (cherry picked from commit 0b3bd0cdc329a1e2e00995cffd61aacf58c87cb4) Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
2020-01-21drm/i915/userptr: fix size calculationMatthew Auld
If we create a rather large userptr object(e.g 1ULL << 32) we might shift past the type-width of num_pages: (int)num_pages << PAGE_SHIFT, resulting in a totally bogus sg_table, which fortunately will eventually manifest as: gen8_ppgtt_insert_huge:463 GEM_BUG_ON(iter->sg->length < page_size) kernel BUG at drivers/gpu/drm/i915/gt/gen8_ppgtt.c:463! v2: more unsigned long prefer I915_GTT_PAGE_SIZE Fixes: 5cc9ed4b9a7a ("drm/i915: Introduce mapping of user pages into video memory (userptr) ioctl") Signed-off-by: Matthew Auld <matthew.auld@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20200117132413.1170563-2-matthew.auld@intel.com (cherry picked from commit 8e78871bc1e5efec22c950d3fd24ddb63d4ff28a) Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
2020-01-21ALSA: hda/hdmi - add retry logic to parse_intel_hdmi()Kai Vehmanen
The initial snd_hda_get_sub_node() can fail on certain devices (e.g. some Chromebook models using Intel GLK). The failure rate is very low, but as this is is part of the probe process, end-user impact is high. In observed cases, related hardware status registers have expected values, but the node query still fails. Retrying the node query does seem to help, so fix the problem by adding retry logic to the query. This does not impact non-Intel platforms. BugLink: https://github.com/thesofproject/linux/issues/1642 Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com> Reviewed-by: Takashi Iwai <tiwai@suse.de> Link: https://lore.kernel.org/r/20200120160117.29130-4-kai.vehmanen@linux.intel.com Signed-off-by: Takashi Iwai <tiwai@suse.de>
2020-01-21ALSA: hda: No preallocation on x86 platformsTakashi Iwai
Like many other drivers, HD-audio drivers also do PCM buffer preallocation to assure the buffer pages allocated at the early boot stage. This step is useful for platforms that may fail to allocate the PCM hardware buffers -- which is mostly for either large continuous pages or with the specific DMA mask (like emu10k1). OTOH, when a buffer is allocated as SG-buffer and the DMA mask is either 32 or 64 bits, the allocation almost never fails unless it hits the real OOM situation. In such a case, we don't need the preallocation inevitably unlike the cases above. That said, we may drop the preallocation for HD-audio that does allocate via SG-buffers, and the patch achieves it. However, there is one caveat: the buffer allocation behavior depends on CONFIG_SND_DMA_SGBUF, and it falls back to the continuous pages when it's not set. And, currently this SG buffer allocation is enabled only on x86 platforms. So, covering those fall-outs, the patch adjusts CONFIG_SND_HDA_PREALLOC_SIZE depending on the condition, and keeps the old behavior as-is for non-x86 platforms. On x86, the kconfig item is no longer adjustable but always set to zero for disabling the preallocation. You can still enable the preallocation via procfs interface at any time later, too. Link: https://lore.kernel.org/r/20200120124423.11862-2-tiwai@suse.de Signed-off-by: Takashi Iwai <tiwai@suse.de>
2020-01-21ALSA: pcm: Set per-card upper limit of PCM buffer allocationsTakashi Iwai
Currently, the available buffer allocation size for a PCM stream depends on the preallocated size; when a buffer has been preallocated, the max buffer size is set to that size, so that application won't re-allocate too much memory. OTOH, when no preallocation is done, each substream may allocate arbitrary size of buffers as long as snd_pcm_hardware.buffer_bytes_max allows -- which can be quite high, HD-audio sets 1GB there. It means that the system may consume a high amount of pages for PCM buffers, and they are pinned and never swapped out. This can lead to OOM easily. For avoiding such a situation, this patch adds the upper limit per card. Each snd_pcm_lib_malloc_pages() and _free_pages() calls are tracked and it will return an error if the total amount of buffers goes over the defined upper limit. The default value is set to 32MB, which should be really large enough for usual operations. If larger buffers are needed for any specific usage, it can be adjusted (also dynamically) via snd_pcm.max_alloc_per_card option. Setting zero there means no chceck is performed, and again, unlimited amount of buffers are allowed. Link: https://lore.kernel.org/r/20200120124423.11862-1-tiwai@suse.de Signed-off-by: Takashi Iwai <tiwai@suse.de>
2020-01-21dmaengine: ti: k3-udma: Add glue layer for non DMAengine usersGrygorii Strashko
Certain users can not use right now the DMAengine API due to missing features in the core. Prime example is Networking. These users can use the glue layer interface to avoid misuse of DMAengine API and when the core gains the needed features they can be converted to use generic API. The most prominent features the glue layer clients are depending on: - most PSI-L native peripheral use extra rflow ranges on a receive channel and depending on the peripheral's configuration packets from a single free descriptor ring is going to be received to different receive ring - it is also possible to have different free descriptor rings per rflow and an rflow can also support 4 additional free descriptor ring based on the size of the incoming packet - out of order completion of descriptors on a channel - when we have several queues to handle different priority packets the descriptors will be completed 'out-of-order' - the notion of prep_slave_sg is not matching with what the streaming type of operation is demanding for networking - Streaming type of operation - Ability to fill the free descriptor ring with descriptors in anticipation of incoming traffic and when a packet arrives UDMAP will form a packet and gives it to the client driver - the descriptors are not backed with exact size data buffers as we don't know the size of the packet we will receive, but as a generic pool of buffers to be used by the receive channel - NAPI type of operation (polling instead of interrupt driven transfer) - without this we can not sustain gigabit speeds and we need to support NAPI - not to limit this to networking, but other high performance operations Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Tested-by: Keerthy <j-keerthy@ti.com> Link: https://lore.kernel.org/r/20191223110458.30766-12-peter.ujfalusi@ti.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
2020-01-21dmaengine: ti: New driver for K3 UDMAPeter Ujfalusi
Split patch for review containing: defines, structs, io and low level functions and interrupt callbacks. DMA driver for Texas Instruments K3 NAVSS Unified DMA – Peripheral Root Complex (UDMA-P) The UDMA-P is intended to perform similar (but significantly upgraded) functions as the packet-oriented DMA used on previous SoC devices. The UDMA-P module supports the transmission and reception of various packet types. The UDMA-P is architected to facilitate the segmentation and reassembly of SoC DMA data structure compliant packets to/from smaller data blocks that are natively compatible with the specific requirements of each connected peripheral. Multiple Tx and Rx channels are provided within the DMA which allow multiple segmentation or reassembly operations to be ongoing. The DMA controller maintains state information for each of the channels which allows packet segmentation and reassembly operations to be time division multiplexed between channels in order to share the underlying DMA hardware. An external DMA scheduler is used to control the ordering and rate at which this multiplexing occurs for Transmit operations. The ordering and rate of Receive operations is indirectly controlled by the order in which blocks are pushed into the DMA on the Rx PSI-L interface. The UDMA-P also supports acting as both a UTC and UDMA-C for its internal channels. Channels in the UDMA-P can be configured to be either Packet-Based or Third-Party channels on a channel by channel basis. The initial driver supports: - MEM_TO_MEM (TR mode) - DEV_TO_MEM (Packet / TR mode) - MEM_TO_DEV (Packet / TR mode) - Cyclic (Packet / TR mode) - Metadata for descriptors Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Tested-by: Keerthy <j-keerthy@ti.com> Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com> Link: https://lore.kernel.org/r/20191223110458.30766-11-peter.ujfalusi@ti.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
2020-01-21dt-bindings: dma: ti: Add document for K3 UDMAPeter Ujfalusi
New binding document for Texas Instruments K3 NAVSS Unified DMA – Peripheral Root Complex (UDMA-P). UDMA-P is introduced as part of the K3 architecture and can be found in AM654 and j721e. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Reviewed-by: Rob Herring <robh@kernel.org> Tested-by: Keerthy <j-keerthy@ti.com> Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com> Link: https://lore.kernel.org/r/20191223110458.30766-10-peter.ujfalusi@ti.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
2020-01-21dmaengine: ti: k3 PSI-L remote endpoint configurationPeter Ujfalusi
In K3 architecture the DMA operates within threads. One end of the thread is UDMAP, the other is on the peripheral side. The UDMAP channel configuration depends on the needs of the remote endpoint and it can be differ from peripheral to peripheral. This patch adds database for am654 and j721e and small API to fetch the PSI-L endpoint configuration from the database which should only used by the DMA driver(s). Another API is added for native peripherals to give possibility to pass new configuration for the threads they are using, which is needed to be able to handle changes caused by different firmware loaded for the peripheral for example. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Tested-by: Keerthy <j-keerthy@ti.com> Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com> Link: https://lore.kernel.org/r/20191223110458.30766-9-peter.ujfalusi@ti.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
2020-01-21dmaengine: ti: Add cppi5 header for K3 NAVSS/UDMAPeter Ujfalusi
The K3 DMA architecture uses CPPI5 (Communications Port Programming Interface) specified descriptors over PSI-L bus within NAVSS. The header provides helpers, macros to work with these descriptors in a consistent way. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Tested-by: Keerthy <j-keerthy@ti.com> Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com> Link: https://lore.kernel.org/r/20191223110458.30766-8-peter.ujfalusi@ti.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
2020-01-21dmaengine: Add helper function to convert direction value to textPeter Ujfalusi
dmaengine_get_direction_text() can be useful when the direction is printed out. The text is easier to comprehend than the number. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Link: https://lore.kernel.org/r/20191223110458.30766-7-peter.ujfalusi@ti.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
2020-01-21dmaengine: Add support for reporting DMA cached data amountPeter Ujfalusi
A DMA hardware can have big cache or FIFO and the amount of data sitting in the DMA fabric can be an interest for the clients. For example in audio we want to know the delay in the data flow and in case the DMA have significantly large FIFO/cache, it can affect the latenc/delay Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Reviewed-by: Tero Kristo <t-kristo@ti.com> Tested-by: Keerthy <j-keerthy@ti.com> Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com> Link: https://lore.kernel.org/r/20191223110458.30766-6-peter.ujfalusi@ti.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
2020-01-21dmaengine: Add metadata_ops for dma_async_tx_descriptorPeter Ujfalusi
The metadata is best described as side band data or parameters traveling alongside the data DMAd by the DMA engine. It is data which is understood by the peripheral and the peripheral driver only, the DMA engine see it only as data block and it is not interpreting it in any way. The metadata can be different per descriptor as it is a parameter for the data being transferred. If the DMA supports per descriptor metadata it can implement the attach, get_ptr/set_len callbacks. Client drivers must only use either attach or get_ptr/set_len to avoid misconfiguration. Client driver can check if a given metadata mode is supported by the channel during probe time with dmaengine_is_metadata_mode_supported(chan, DESC_METADATA_CLIENT); dmaengine_is_metadata_mode_supported(chan, DESC_METADATA_ENGINE); and based on this information can use either mode. Wrappers are also added for the metadata_ops. To be used in DESC_METADATA_CLIENT mode: dmaengine_desc_attach_metadata() To be used in DESC_METADATA_ENGINE mode: dmaengine_desc_get_metadata_ptr() dmaengine_desc_set_metadata_len() Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Reviewed-by: Tero Kristo <t-kristo@ti.com> Tested-by: Keerthy <j-keerthy@ti.com> Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com> Link: https://lore.kernel.org/r/20191223110458.30766-5-peter.ujfalusi@ti.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
2020-01-21dmaengine: doc: Add sections for per descriptor metadata supportPeter Ujfalusi
Update the provider and client documentation with details about the metadata support. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Reviewed-by: Tero Kristo <t-kristo@ti.com> Tested-by: Keerthy <j-keerthy@ti.com> Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com> Link: https://lore.kernel.org/r/20191223110458.30766-4-peter.ujfalusi@ti.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
2020-01-21Merge TI ringacc driver from SantoshVinod Koul
This is for dependency of new TI ringacc dmaengine drivers Merge tag 'drivers_soc_for_5.6' into topic/ti SOC: TI Keystone Ring Accelerator driver The Ring Accelerator (RINGACC or RA) provides hardware acceleration to enable straightforward passing of work between a producer and a consumer. There is one RINGACC module per NAVSS on TI AM65x SoCs. Signed-off-by: Vinod Koul <vkoul@kernel.org>
2020-01-21scsi: RDMA/isert: Fix a recently introduced regression related to logoutBart Van Assche
iscsit_close_connection() calls isert_wait_conn(). Due to commit e9d3009cb936 both functions call target_wait_for_sess_cmds() although that last function should be called only once. Fix this by removing the target_wait_for_sess_cmds() call from isert_wait_conn() and by only calling isert_wait_conn() after target_wait_for_sess_cmds(). Fixes: e9d3009cb936 ("scsi: target: iscsi: Wait for all commands to finish before freeing a session"). Link: https://lore.kernel.org/r/20200116044737.19507-1-bvanassche@acm.org Reported-by: Rahul Kundu <rahul.kundu@chelsio.com> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Tested-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Acked-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2020-01-20scsi: fnic: do not queue commands during fwresetHannes Reinecke
When a link is going down the driver will be calling fnic_cleanup_io(), which will traverse all commands and calling 'done' for each found command. While the traversal is handled under the host_lock, calling 'done' happens after the host_lock is being dropped. As fnic_queuecommand_lck() is being called with the host_lock held, it might well be that it will pick the command being selected for abortion from the above routine and enqueue it for sending, but then 'done' is being called on that very command from the above routine. Which of course confuses the hell out of the scsi midlayer. So fix this by not queueing commands when fnic_cleanup_io is active. Link: https://lore.kernel.org/r/20200116102053.62755-1-hare@suse.de Signed-off-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2020-01-20Input: pm8xxx-vib - fix handling of separate enable registerStephan Gerhold
Setting the vibrator enable_mask is not implemented correctly: For regmap_update_bits(map, reg, mask, val) we give in either regs->enable_mask or 0 (= no-op) as mask and "val" as value. But "val" actually refers to the vibrator voltage control register, which has nothing to do with the enable_mask. So we usually end up doing nothing when we really wanted to enable the vibrator. We want to set or clear the enable_mask (to enable/disable the vibrator). Therefore, change the call to always modify the enable_mask and set the bits only if we want to enable the vibrator. Fixes: d4c7c5c96c92 ("Input: pm8xxx-vib - handle separate enable register") Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Link: https://lore.kernel.org/r/20200114183442.45720-1-stephan@gerhold.net Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2020-01-20Merge branch 'libbpf-include-path'Alexei Starovoitov
Toke Høiland-Jørgensen says: ==================== We are currently being somewhat inconsistent with the libbpf include paths, which makes it difficult to move files from the kernel into an external libbpf-using project without adjusting include paths. Having the bpf/ subdir of $INCLUDEDIR in the include path has never been a requirement for building against libbpf before, and indeed the libbpf pkg-config file doesn't include it. So let's make all libbpf includes across the kernel tree use the bpf/ prefix in their includes. Since bpftool skeleton generation emits code with a libbpf include, this also ensures that those can be used in existing external projects using the regular pkg-config include path. This turns out to be a somewhat invasive change in the number of files touched; however, the actual changes to files are fairly trivial (most of them are simply made with 'sed'). The series is split to make the change for one tool subdir at a time, while trying not to break the build along the way. It is structured like this: - Patch 1-3: Trivial fixes to Makefiles for issues I discovered while changing the include paths. - Patch 4-8: Change the include directives to use the bpf/ prefix, and updates Makefiles to make sure tools/lib/ is part of the include path, but without removing tools/lib/bpf - Patch 9-11: Remove tools/lib/bpf from include paths to make sure we don't inadvertently re-introduce includes without the bpf/ prefix. Changelog: v5: - Combine the libbpf build rules in selftests Makefile (using Andrii's suggestion for a make rule). - Re-use self-tests libbpf build for runqslower (new patch 10) - Formatting fixes v4: - Move runqslower error on missing BTF into make rule - Make sure we don't always force a rebuild selftests - Rebase on latest bpf-next (dropping patch 11) v3: - Don't add the kernel build dir to the runqslower Makefile, pass it in from selftests instead. - Use libbpf's 'make install_headers' in selftests instead of trying to generate bpf_helper_defs.h in-place (to also work on read-only filesystems). - Use a scratch builddir for both libbpf and bpftool when building in selftests. - Revert bpf_helpers.h to quoted include instead of angled include with a bpf/ prefix. - Fix a few style nits from Andrii v2: - Do a full cleanup of libbpf includes instead of just changing the bpf_helper_defs.h include. ==================== Acked-by: Andrii Nakryiko <andriin@fb.com> Tested-by: Andrii Nakryiko <andriin@fb.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org>
2020-01-20selftests: Refactor build to remove tools/lib/bpf from include pathToke Høiland-Jørgensen
To make sure no new files are introduced that doesn't include the bpf/ prefix in its #include, remove tools/lib/bpf from the include path entirely. Instead, we introduce a new header files directory under the scratch tools/ dir, and add a rule to run the 'install_headers' rule from libbpf to have a full set of consistent libbpf headers in $(OUTPUT)/tools/include/bpf, and then use $(OUTPUT)/tools/include as the include path for selftests. For consistency we also make sure we put all the scratch build files from other bpftool and libbpf into tools/build/, so everything stays within selftests/. Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Link: https://lore.kernel.org/bpf/157952561246.1683545.2762245552022369203.stgit@toke.dk
2020-01-20runsqslower: Support user-specified libbpf include and object pathsToke Høiland-Jørgensen
This adds support for specifying the libbpf include and object paths as arguments to the runqslower Makefile, to support reusing the libbpf version built as part of the selftests. Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Link: https://lore.kernel.org/bpf/157952561135.1683545.5660339645093141381.stgit@toke.dk
2020-01-20tools/runqslower: Remove tools/lib/bpf from include pathToke Høiland-Jørgensen
Since we are now consistently using the bpf/ prefix on #include directives, we don't need to include tools/lib/bpf in the include path. Remove it to make sure we don't inadvertently introduce new includes without the prefix. Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Andrii Nakryiko <andriin@fb.com> Link: https://lore.kernel.org/bpf/157952561027.1683545.1976265477926794138.stgit@toke.dk
generated by cgit (git 2.34.1) at 2025-09-14 15:17:05 +0000