| Age | Commit message (Collapse) | Author |
|---|
|
In __ghes_panic() clear the block status in the APEI generic
error status block for that generic hardware error source before
calling panic() to prevent a second panic() in the crash kernel
for exactly the same fatal error.
Otherwise ghes_probe(), running in the crash kernel, would see
an unhandled error in the APEI generic error status block and
panic again, thereby precluding any crash dump.
Signed-off-by: Lenny Szubowicz <lszubowi@redhat.com>
Signed-off-by: David Arcari <darcari@redhat.com>
Tested-by: Tyler Baicar <baicar.tyler@gmail.com>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
From git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
mlx5 updates taken for dependencies on following patches.
* branche 'mlx5-next': (23 commits)
IB/mlx5: Introduce uid as part of alloc/dealloc transport domain
net/mlx5: Add shared Q counter bits
net/mlx5: Continue driver initialization despite debugfs failure
net/mlx5: Fold the modify lag code into function
net/mlx5: Add lag affinity info to log
net/mlx5: Split the activate lag function into two routines
net/mlx5: E-Switch, Introduce flow counter affinity
IB/mlx5: Unify e-switch representors load approach between uplink and VFs
net/mlx5: Use lowercase 'X' for hex values
net/mlx5: Remove duplicated include from eswitch.c
net/mlx5: Remove the get protocol device interface entry
net/mlx5: Support extended destination format in flow steering command
net/mlx5: E-Switch, Change vhca id valid bool field to bit flag
net/mlx5: Introduce extended destination fields
net/mlx5: Revise gre and nvgre key formats
net/mlx5: Add monitor commands layout and event data
net/mlx5: Add support for plugged-disabled cable status in PME
net/mlx5: Add support for PCIe power slot exceeded error in PME
net/mlx5: Rework handling of port module events
net/mlx5: Move flow counters data structures from flow steering header
...
|
|
Use the mii_bus callbacks to address the entire clause 22/45 address
space. Enables userspace to poke switch registers instead of a single
PHY address.
The ixgbe firmware may be polling PHYs in a way that is not protected by
the mii_bus lock. This isn't new behavior, but as Andrew Lunn pointed
out there are more addresses available for conflicts.
Signed-off-by: Stephen Douthit <stephend@silicom-usa.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Most dsa devices expect a 'struct mii_bus' pointer to talk to switches
via the MII interface.
While this works for dsa devices, it will not work safely with Linux
PHYs in all configurations since the firmware of the ixgbe device may
be polling some PHY addresses in the background.
Signed-off-by: Stephen Douthit <stephend@silicom-usa.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
I210 ethernet card doesn't wakeup when a cable gets plugged. It's
because its PME is not set.
Since commit 42eca2302146 ("PCI: Don't touch card regs after runtime
suspend D3"), if the PCI state is saved, pci_pm_runtime_suspend() stops
calling pci_finish_runtime_suspend(), which enables the PCI PME.
To fix the issue, let's not to save PCI states when it's runtime
suspend, to let the PCI subsystem enables PME.
Fixes: 42eca2302146 ("PCI: Don't touch card regs after runtime suspend D3")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
If ice driver has q_vectors w/ active NAPI that has no rings,
then this will result in a divide by zero error. To correct it
I am updating the driver code so that we only support NAPI on
q_vectors that have 1 or more rings allocated to them.
See commit 13a8cd191a2b ("i40e: Do not enable NAPI on q_vectors
that have no rings") for detail.
Signed-off-by: Young Xiao <YangX92@hotmail.com>
Acked-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This adds support for the PTP_SYS_OFFSET_EXTENDED ioctl.
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Out of bound read reported by KASan.
i40iw_net_event() reads unconditionally 16 bytes from
neigh->primary_key while the memory allocated for
"neighbour" struct is evaluated in neigh_alloc() as
tbl->entry_size + dev->neigh_priv_len
where "dev" is a net_device.
But the driver does not setup dev->neigh_priv_len and
we read beyond the neigh entry allocated memory,
so the patch in the next mail fixes this.
Signed-off-by: Konstantin Khorenko <khorenko@virtuozzo.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Fix a static code checker warning:
drivers/net/ethernet/intel/e100.c:1349
e100_load_ucode_wait() warn: passing zero to 'PTR_ERR'
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add some pointers to the definition of the CBS algorithm, and some
notes about the limits of its implementation in the i210 family of
controllers.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Section 4.5.9 of the datasheet says that the total size of all packet
buffers combined (TxPB 0 + 1 + 2 + 3 + RxPB + BMC2OS + OS2BMC) must not
exceed 60KB. Today we are configuring a total of 62KB, so reduce the
RxPB from 32KB to 30KB in order to respect that.
The choice of changing RxPBSIZE here is mainly because it seems more
correct to give more priority to the transmit packet buffers over the
receiver ones when running in Qav mode. Also, the BMC2OS and OS2BMC
sizes are already too short.
Signed-off-by: Jesus Sanchez-Palencia <jesus.s.palencia@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
sbq_wake_ptr() checks sbq->ws_active to know if it needs to loop
the wait indexes or not. This requires the use of the sbitmap
waitqueue wrappers, but kyber doesn't use those for its domain
token waitqueue handling.
Convert kyber to use the helpers. This fixes a hang with waiting
for domain tokens.
Fixes: 5d2ee7122c73 ("sbitmap: optimize wakeup check")
Tested-by: Ming Lei <ming.lei@redhat.com>
Reported-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
After commit 5d2ee7122c73, users of sbitmap that need wait queue
handling must use the provided helpers. But we only added
prepare_to_wait()/finish_wait() style helpers, add the equivalent
add_wait_queue/list_del wrappers as we..
This is needed to ensure kyber plays by the sbitmap waitqueue
rules.
Tested-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This change is based off of the work and suggestion of Jan Jablonsky
<jan.jablonsky@thalesgroup.com>.
The Watchdog workqueue in igb driver is scheduled every 2s for each
network interface. That includes updating a statistics protected by
spinlock. Function igb_update_stats in this case will be protected
against preemption. According to number of a statistics registers
(cca 60), processing this function might cause additional cpu load
on CPU0.
In case of statistics spinlock may be replaced with mutex, which
reduce latency on CPU0.
CC: Bernhard Kaindl <bernhard.kaindl@thalesgroup.com>
CC: Jan Jablonsky <jan.jablonsky@thalesgroup.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When unregistering fbdev using unregister_framebuffer(), any bound
console will unbind automatically. This is working fine if this is the
only framebuffer, resulting in a switch to the dummy console. However if
there is a fb0 and I unregister fb1 having a bound console, I eventually
get a crash. The fastest way for me to trigger the crash is to do a
reboot, resulting in this splat:
[ 76.478825] WARNING: CPU: 0 PID: 527 at linux/kernel/workqueue.c:1442 __queue_work+0x2d4/0x41c
[ 76.478849] Modules linked in: raspberrypi_hwmon gpio_backlight backlight bcm2835_rng rng_core [last unloaded: tinydrm]
[ 76.478916] CPU: 0 PID: 527 Comm: systemd-udevd Not tainted 4.20.0-rc4+ #4
[ 76.478933] Hardware name: BCM2835
[ 76.478949] Backtrace:
[ 76.478995] [<c010d388>] (dump_backtrace) from [<c010d670>] (show_stack+0x20/0x24)
[ 76.479022] r6:00000000 r5:c0bc73be r4:00000000 r3:6fb5bf81
[ 76.479060] [<c010d650>] (show_stack) from [<c08e82f4>] (dump_stack+0x20/0x28)
[ 76.479102] [<c08e82d4>] (dump_stack) from [<c0120070>] (__warn+0xec/0x12c)
[ 76.479134] [<c011ff84>] (__warn) from [<c01201e4>] (warn_slowpath_null+0x4c/0x58)
[ 76.479165] r9:c0eb6944 r8:00000001 r7:c0e927f8 r6:c0bc73be r5:000005a2 r4:c0139e84
[ 76.479197] [<c0120198>] (warn_slowpath_null) from [<c0139e84>] (__queue_work+0x2d4/0x41c)
[ 76.479222] r6:d7666a00 r5:c0e918ee r4:dbc4e700
[ 76.479251] [<c0139bb0>] (__queue_work) from [<c013a02c>] (queue_work_on+0x60/0x88)
[ 76.479281] r10:c0496bf8 r9:00000100 r8:c0e92ae0 r7:00000001 r6:d9403700 r5:d7666a00
[ 76.479298] r4:20000113
[ 76.479348] [<c0139fcc>] (queue_work_on) from [<c0496c28>] (cursor_timer_handler+0x30/0x54)
[ 76.479374] r7:d8a8fabc r6:c0e08088 r5:d8afdc5c r4:d8a8fabc
[ 76.479413] [<c0496bf8>] (cursor_timer_handler) from [<c0178744>] (call_timer_fn+0x100/0x230)
[ 76.479435] r4:c0e9192f r3:d758a340
[ 76.479465] [<c0178644>] (call_timer_fn) from [<c0178980>] (expire_timers+0x10c/0x12c)
[ 76.479495] r10:40000000 r9:c0e9192f r8:c0e92ae0 r7:d8afdccc r6:c0e19280 r5:c0496bf8
[ 76.479513] r4:d8a8fabc
[ 76.479541] [<c0178874>] (expire_timers) from [<c0179630>] (run_timer_softirq+0xa8/0x184)
[ 76.479570] r9:00000001 r8:c0e19280 r7:00000000 r6:c0e08088 r5:c0e1a3e0 r4:c0e19280
[ 76.479603] [<c0179588>] (run_timer_softirq) from [<c0102404>] (__do_softirq+0x1ac/0x3fc)
[ 76.479632] r10:c0e91680 r9:d8afc020 r8:0000000a r7:00000100 r6:00000001 r5:00000002
[ 76.479650] r4:c0eb65ec
[ 76.479686] [<c0102258>] (__do_softirq) from [<c0124d10>] (irq_exit+0xe8/0x168)
[ 76.479716] r10:d8d1a9b0 r9:d8afc000 r8:00000001 r7:d949c000 r6:00000000 r5:c0e8b3f0
[ 76.479734] r4:00000000
[ 76.479764] [<c0124c28>] (irq_exit) from [<c016b72c>] (__handle_domain_irq+0x94/0xb0)
[ 76.479793] [<c016b698>] (__handle_domain_irq) from [<c01021dc>] (bcm2835_handle_irq+0x3c/0x48)
[ 76.479823] r8:d8afdebc r7:d8afddfc r6:ffffffff r5:c0e089f8 r4:d8afddc8 r3:d8afddc8
[ 76.479851] [<c01021a0>] (bcm2835_handle_irq) from [<c01019f0>] (__irq_svc+0x70/0x98)
The problem is in the console rebinding in fbcon_fb_unbind(). It uses the
virtual console index as the new framebuffer index to bind the console(s)
to. The correct way is to use the con2fb_map lookup table to find the
framebuffer index.
Fixes: cfafca8067c6 ("fbdev: fbcon: console unregistration from unregister_framebuffer")
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Mikulas Patocka <mpatocka@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
|
|
Remove dependencies on HAS_DMA where a Kconfig symbol depends on another
symbol that implies HAS_DMA, and, optionally, on "|| COMPILE_TEST".
In most cases this other symbol is an architecture or platform specific
symbol, or PCI.
Generic symbols and drivers without platform dependencies keep their
dependencies on HAS_DMA, to prevent compiling subsystems or drivers that
cannot work anyway.
This simplifies the dependencies, and allows to improve compile-testing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
|
|
A missing space in an error message.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Cc: Jiri Kosina <trivial@kernel.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
|
|
The null check on &info->cmap is redundant since cmap is a struct
inside fb_info and can never be null, so the check is always true.
We may remove it.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Acked-by: Timur Tabi <timur@kernel.org>
Cc: zhong.weidong@zte.com.cn
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
|
|
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
|
|
There is a spelling mistake in the module parameter description, fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Cc: Michal Januszewski <spock@gentoo.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
|
|
If there are extra logos (CONFIG_FB_LOGO_EXTRA) the heights of these
extra logos are not considered when centering the first logo vertically.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
|
|
In preparation for allowing centering of the bootup logo, make
fb_show_logo_line return where the next free framebuffer line is,
instead of returning the height of the shown logo.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
|
|
'info->modes' got allocated with devm_kcalloc in of_get_pxafb_display.
This gives this error message:
./drivers/video/fbdev/pxafb.c:2238:2-7: WARNING: invalid free of devm_ allocated data
Fixes: c8f96304ec8b4 ("video: fbdev: pxafb: switch to devm_* API")
Cc: stable@kernel.org [v4.19+]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Daniel Mack <daniel@zonque.org>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
|
|
Blitting an image with "negative" offsets is not working since there
is no clipping. It hopefully just crashes. For the bootup logo, there
is protection so that blitting does not happen as the image is drawn
further and further to the right (ROTATE_UR) or further and further
down (ROTATE_CW). There is however no protection when drawing in the
opposite directions (ROTATE_UD and ROTATE_CCW).
Add back this protection.
The regression is 20-odd years old but the mindless warning-killing
mentality displayed in commit 34bdb666f4b2 ("fbdev: fbmem: remove
positive test on unsigned values") is also to blame, methinks.
Fixes: 448d479747b8 ("fbdev: fb_do_show_logo() updates")
Signed-off-by: Peter Rosin <peda@axentia.se>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Fabian Frederick <ffrederick@users.sourceforge.net>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
cc: Geoff Levand <geoff@infradead.org>
Cc: James Simmons <jsimmons@users.sf.net>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
|
|
clps711x_fb_probe() increments refcnt of disp device node by
of_parse_phandle() and leaves it undecremented on both
successful and error paths.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Cc: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
|
|
BACKLIGHT_CLASS_DEVICE is already tristate, but a dependency
FB_BACKLIGHT prevents it from being built as a module. There
doesn't seem to be any particularly good reason for this, so
switch FB_BACKLIGHT over to tristate.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Tested-by: Arnd Bergmann <arnd@arndb.de>
Cc: Simon Horman <horms+renesas@verge.net.au>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Ulf Magnusson <ulfalizer@gmail.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Hans de Goede <j.w.r.degoede@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
|
|
In the current kernel, then kzalloc() can't fail for small allocations,
but if it did fail then we would have a NULL dereference in the error
handling. Also in dlfb_usb_disconnect() if "info" were NULL then it
would cause an Oops inside the unregister_framebuffer() function but it
can't be NULL so let's remove that check.
Fixes: 68a958a915ca ("udlfb: handle unplug properly")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Bernie Thompson <bernie@plugable.com>
Cc: Mikulas Patocka <mpatocka@redhat.com>
Cc: Alexey Khoroshilov <khoroshilov@ispras.ru>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Wen Yang <wen.yang99@zte.com.cn>
[b.zolnierkie: added "Fixes:" tag]
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
|
|
Mapping the delay slot emulation page as both writeable & executable
presents a security risk, in that if an exploit can write to & jump into
the page then it can be used as an easy way to execute arbitrary code.
Prevent this by mapping the page read-only for userland, and using
access_process_vm() with the FOLL_FORCE flag to write to it from
mips_dsemul().
This will likely be less efficient due to copy_to_user_page() performing
cache maintenance on a whole page, rather than a single line as in the
previous use of flush_cache_sigtramp(). However this delay slot
emulation code ought not to be running in any performance critical paths
anyway so this isn't really a problem, and we can probably do better in
copy_to_user_page() anyway in future.
A major advantage of this approach is that the fix is small & simple to
backport to stable kernels.
Reported-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: 432c6bacbd0c ("MIPS: Use per-mm page to execute branch delay slot instructions")
Cc: stable@vger.kernel.org # v4.8+
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Rich Felker <dalias@libc.org>
Cc: David Daney <david.daney@cavium.com>
|
|
In commit 4f83d5ea643a ("security: integrity: make ima_main explicitly
non-modular") I'd removed <linux/module.h> after assuming that the
function is_module_sig_enforced() was an LSM function and not a core
kernel module function.
Unfortunately the typical .config selections used in build testing
provide an implicit <linux/module.h> presence, and so normal/typical
build testing did not immediately reveal my incorrect assumption.
Cc: Mimi Zohar <zohar@linux.vnet.ibm.com>
Cc: Dmitry Kasatkin <dmitry.kasatkin@gmail.com>
Cc: James Morris <james.l.morris@oracle.com>
Cc: "Serge E. Hallyn" <serge@hallyn.com>
Cc: linux-ima-devel@lists.sourceforge.net
Cc: linux-security-module@vger.kernel.org
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/core
Pull perf/core improvements and fixes from Arnaldo Carvalho de Melo:
- Implement BPF based syscall filtering in 'perf trace', using BPF maps and
the augmented_raw_syscalls.c BPF proggie (Arnaldo Carvalho de Melo)
- Allow specifying in .perfconfig a set of events use in 'perf trace' in
addition to any other specified from the command line. This initially
will be used to always use the augmented_raw_syscalls.o precompiled
BPF program for getting pointer contents. (Arnaldo Carvalho de Melo)
- Allow fine grained control about how the syscall output should be
formatted. This will be used to allow producing the same output produced
by the 'strace' tool, to then use in regression tests comparing the
output of 'perf trace' with the one produced from 'strace' (Arnaldo Carvalho de Melo)
- Beautify the renameat2 olddirfd, newdirfd and flags arguments (Arnaldo Carvalho de Melo)
- Beautify arch_prctl 'code' syscall arg (Arnaldo Carvalho de Melo)
- Beautify fadvise64 'advice' syscall arg (Arnaldo Carvalho de Melo)
- Relax checks on perf-PID.map ownership, resulting in symbols in
executable anonymous maps setup by JITs in things like node.js to
be resolved in a 'perf top' session run by root without the need
for --force to be used (Arnaldo Carvalho de Melo)
- Update asm-generic/unistd.h copy (Arnaldo Carvalho de Melo)
- Do not use the first and last symbols when setting up address filters in
auxtrace, this fails when we don't have a symbol table, filter the entire
area based on the dso size. (Adrian Hunter)
- Do not use kernel headers to build libsubcmd, we shouldn't use
anything from outside tools/, fixes the build with the Android NDK (Arnaldo Carvalho de Melo)
- Add several prototypes for systems lacking those, such as open_memstream(),
sigqueue(), fixing warnings building with Android's bionic libc that were
preventing the use of -Werror there (Arnaldo Carvalho de Melo)
- Use LDFLAGS in the libtraceevent build commands, allowing developers
to override its values (Jiri Olsa)
- Link libperf-jvmti.so with LDFLAGS variable, allowing distro
packages to propagate its settings when building this library (Jiri Olsa)
- cs-etm (ARM CoreSight) fixes: (Leo Yan)
- Correct packets swapping in cs_etm__flush()
- Avoid stale branch samples when flush packet
- Remove unused 'trace_on' in cs_etm_decoder
- Refactor enumeration cs_etm_sample_type
- Rename CS_ETM_TRACE_ON to CS_ETM_DISCONTINUITY
- Treat NO_SYNC element as trace discontinuity
- Treat EO_TRACE element as trace discontinuity
- Generate branch sample for exception packet
- Use shebangs in the 'perf test' shell scripts, making them identifiable as
shell scripts (Michael Petlan)
- Avoid segfaults caused by negated options in 'perf stat' (Michael Petlan)
- Fix processing of dereferenced args in bprintk events in libtracevent (Steven Rostedt)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
ath.git patches for 4.21. Major changes:
ath10k
* add amsdu support for QCA6174 monitor mode
* report tx rate using the new ieee80211_tx_rate_update() API
* wcn3990 support is not experimental anymore
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
Fix spectre v1 vuln in drm_ioctl
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20181220165740.GA42344@art_vandelay
|
|
Need to blank stream before deallocate MST payload.
[drm:generic_reg_wait [amdgpu]] *ERROR* REG_WAIT timeout 10us * 3000 tries - dce110_stream_encoder_dp_blank line:944
------------[ cut here ]------------
WARNING: CPU: 0 PID: 2201 at /var/lib/dkms/amdgpu/18.50-690240/build/amd/amdgpu/../display/dc/dc_helper.c:249 generic_reg_wait+0xe7/0x160 [amdgpu]
Call Trace:
dce110_stream_encoder_dp_blank+0x11c/0x180 [amdgpu]
core_link_disable_stream+0x40/0x230 [amdgpu]
? generic_reg_update_ex+0xdb/0x130 [amdgpu]
dce110_reset_hw_ctx_wrap+0xb7/0x1f0 [amdgpu]
dce110_apply_ctx_to_hw+0x30/0x430 [amdgpu]
? dce110_apply_ctx_for_surface+0x206/0x260 [amdgpu]
dc_commit_state+0x2ba/0x4d0 [amdgpu]
amdgpu_dm_atomic_commit_tail+0x297/0xd70 [amdgpu]
? amdgpu_bo_pin_restricted+0x58/0x260 [amdgpu]
? wait_for_completion_timeout+0x1f/0x120
? wait_for_completion_interruptible+0x1c/0x160
commit_tail+0x3d/0x60 [drm_kms_helper]
drm_atomic_helper_commit+0xf6/0x100 [drm_kms_helper]
drm_atomic_connector_commit_dpms+0xe5/0xf0 [drm]
drm_mode_obj_set_property_ioctl+0x14f/0x250 [drm]
drm_mode_connector_property_set_ioctl+0x2e/0x40 [drm]
drm_ioctl+0x1e0/0x430 [drm]
? drm_mode_connector_set_obj_prop+0x70/0x70 [drm]
? ep_read_events_proc+0xb0/0xb0
? ep_scan_ready_list.constprop.18+0x1e6/0x1f0
? timerqueue_add+0x52/0x80
amdgpu_drm_ioctl+0x49/0x80 [amdgpu]
do_vfs_ioctl+0x90/0x5f0
SyS_ioctl+0x74/0x80
do_syscall_64+0x74/0x140
entry_SYSCALL_64_after_hwframe+0x3d/0xa2
---[ end trace 3ed7b77a97d60f72 ]---
Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
[why]
Some dongle doesn't have a valid extended dongle caps,
but we still set the extended dongle caps to be valid.
This causes validation fails for all timing.
[how]
If no dp_hdmi_max_pixel_clk is provided,
don't use extended dongle caps.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Abdoulaye Berthe <Abdoulaye.Berthe@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Resolves __udivdi3 missing errors when building for i386.
Fixes: 6378ef012ddc ("drm/amd/display: Add below the range support for FreeSync")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Since umr tool can't handle bracket, change uvd ring name convention.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Support manual LCLK DPM level switch on Vega20.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
When a job is timeout, try to print the related process information
for debugging
Signed-off-by: Trigger Huang <Trigger.Huang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Configure PCIE_CI_CNTL to work around a hw bug that affects
some multi-GPU compute workloads.
Acked-by: Feifei Xu <Feifei.Xu@amd.com>
Reviewed-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Configure PCIE_CI_CNTL to work around a hw bug that affects
some multi-GPU compute workloads.
Acked-by: Feifei Xu <Feifei.Xu@amd.com>
Reviewed-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Changed "avaiable" to "available" and "interupt" to "interrupt".
Signed-off-by: Jona Crasselt <jona.crasselt@fau.de>
Signed-off-by: Felix Windsheimer <felix.windsheimer@fau.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add wmi configuration cmd to configure base band(BB) power amplifier(PA)
off timing values in hardware. The default PA off timings were fine tuned
to make proper DFS radar detection in QCA reference design. If ODM uses
different PA in their design, then the same default PA off timing values
cannot be used, it requires different settling time to detect radar pulses
very sooner and avoid radar detection problems. In that case it provides
provision to select proper PA off timing values based on the PA hardware used.
The PA component is part of FEM hardware and new device tree entry
"ext-fem-name" is used to indentify the FEM hardware. And this wmi configuration
cmd is enabled via wmi service flag "WMI_SERVICE_BB_TIMING_CONFIG_SUPPORT".
Other way is to apply these values through calibration data, but recalibration
of all boards out there might not be feasible.
This change tested on firmware ver 10.2.4-1.0-00042 in QCA988X chipset.
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This adds new dt entry ext-fem-name, it is used by ath10k driver
to select correct timing parameters and configure it in target wifi hardware.
The Front End Module(FEM) normally includes tx power amplifier(PA) and
rx low noise amplifier(LNA). The default timing parameters like tx end to
PA off timing values were fine tuned for internal FEM used in reference
design. And these timing values can not be same if ODM modifies hardware
design with different external FEM. This DT entry helps to choose correct
timing values in driver if different external FEM hardware used.
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In qcom,ath10k documentation, ath10k is used as node name in the example of
pci based device. Normally, node name should be class of device and not the
model name, so fix it to node name "wifi". And remove the property device_type
pci since only pci bridges should have this property.
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Memory of tx_stats was allocated when a STA was added. But it's not freed
if the STA failed to be added to driver. This issue could be seen in MDK3
attack case when STA number reached the limit.
Tested: QCA9984 with firmware ver 10.4-3.9.0.1-00005
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
There was a race condition in SMP that an ath10k_peer was created but its
member sta was null. Following are procedures of ath10k_peer creation and
member sta access in peer statistics path.
1. Peer creation:
ath10k_peer_create()
=>ath10k_wmi_peer_create()
=>ath10k_wait_for_peer_created()
...
# another kernel path, RX from firmware
ath10k_htt_t2h_msg_handler()
=>ath10k_peer_map_event()
=>wake_up()
# ar->peer_map[id] = peer //add peer to map
#wake up original path from waiting
...
# peer->sta = sta //sta assignment
2. RX path of statistics
ath10k_htt_t2h_msg_handler()
=>ath10k_update_per_peer_tx_stats()
=>ath10k_htt_fetch_peer_stats()
# peer->sta //sta accessing
Any access of peer->sta after peer was added to peer_map but before sta was
assigned could cause a null pointer issue. And because these two steps are
asynchronous, no proper lock can protect them. So both peer and sta need to
be checked before access.
Tested: QCA9984 with firmware ver 10.4-3.9.0.1-00005
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
WCN3990 wifi module can optionally make use of the IOMMU.
Add binding documentation for phandle to the IOMMU and
the stream id of wifi iommu block.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Add missing optional properties in WCN3990 wifi node.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The "survey" pointer is the address of an array element. We know that
it can't be NULL so this check can be removed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
