| Age | Commit message (Collapse) | Author |
|---|
|
The write_end() function must always unlock the page and drop its ref
count, even on an error.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org
|
|
David Ahern says:
====================
net: ipv6: Improve user experience with multipath routes
This series closes a couple of gaps between IPv4 and IPv6 with respect
to multipath routes:
1. IPv4 allows all nexthops of multipath routes to be deleted using just
the prefix and length; IPv6 only deletes the first nexthop for the
route if only the prefix and length are given.
2. IPv4 returns multipath routes encoded in the RTA_MULTIPATH attribute.
IPv6 returns a series of routes with the same prefix and length - one
for each nexthop. This happens for both dumps and notifications.
IPv6 does accept RTA_MULTIPATH encoded routes, but installs them as a
series of routes.
Patch 1 addresses the first item by allowing IPv6 multipath routes to be
deleted using just the prefix and length. Patch 2 addresses the second
allowing IPv6 multipath routes to be returned encoded in the RTA_MULTIPATH.
Patches 3 and 4 upate the RTM_{NEW,DEL}ROUTE notifications to generate
1 notification with RTA_MULTIPATH where applicable.
Patch 5 prints IPv6 addresses in compressed format when showing route
replace errors. This was noticed testing REPLACE failures.
The end result for multipath routes:
1. Dump
- RTA_MULTIPATH used for multipath routes
$ ip -6 ro ls vrf red
2001:db8:1::/120 dev eth1 proto kernel metric 256 pref medium
2001:db8:2::/120 dev eth2 proto kernel metric 256 pref medium
2001:db8:200::/120 metric 1024
nexthop via 2001:db8:1::2 dev eth1 weight 1
nexthop via 2001:db8:2::2 dev eth2 weight 1
...
2. Route Add
- one notification with RTA_MULTIPATH attribute
$ ip -6 ro add vrf red 2001:db8:200::/120 nexthop via 2001:db8:1::2 nexthop via 2001:db8:2::2
$ ip mon route
2001:db8:200::/120 table red metric 1024
nexthop via 2001:db8:1::2 dev eth1 weight 1
nexthop via 2001:db8:2::2 dev eth2 weight 1
2. Route Replace
- one notification with RTA_MULTIPATH attribute
$ ip -6 ro replace vrf red 2001:db8:200::/120 nexthop via 2001:db8:1::16 nexthop via 2001:db8:2::16
$ ip mon route
Replaced 2001:db8:200::/120 table red metric 1024
nexthop via 2001:db8:1::16 dev eth1 weight 1
nexthop via 2001:db8:2::16 dev eth2 weight 1
- on a failure after the insertion of the first nexthop (which means
the original route has been replaced in the FIB), a notification is
sent with the successful nexthops and then the nexthops are deleted
with one notification per hop. This is consistent with how it works
today except the successful additions are coalesced into 1
notification.
3. Route Delete
- delete of entire multipath route using prefix/length only 1
notification is generated:
$ ip -6 ro del vrf red 2001:db8:200::/120
$ ip mon route
Deleted 2001:db8:200::/120 table red metric 1024
nexthop via 2001:db8:1::16 dev eth1 weight 1
nexthop via 2001:db8:2::16 dev eth2 weight 1
- if a delete request contains nexthops one notification is
generated per nexthop deleted. This is unavoidable since IPv6
alllows a single nexthop to be deleted within a multipath route
4. Route Appends
- IPv6 allows nexthops to be appended to an existing route. In this
case one notification is sent for the new route with the append
flag set.
$ ip -6 ro append vrf red 2001:db8:200::/120 nexthop via 2001:db8:2::20 nexthop via 2001:db8:1::20
$ ip mon route
Append 2001:db8:200::/120 table red metric 1024
nexthop via 2001:db8:1::2 dev eth1 weight 1
nexthop via 2001:db8:2::2 dev eth2 weight 1
nexthop via 2001:db8:2::20 dev eth2 weight 1
nexthop via 2001:db8:1::20 dev eth1 weight 1
- on failure of an append, a notification is sent with the route
containing all of the nexthops successfully added, and it is
followed by delete notifications as the hops are removed
returning the route to its prior state. This is consistent with
how it works today except the successful additions are coalesced
into 1 notification.
Addresses some of the inconsistencies also noted by Roopa at netdev0.1:
https://www.netdev01.org/docs/prabhu-linux_ipv4_ipv6_inconsistencies_talk_slides.pdf
v4
- changed series to do encoding in 1 patch and updating notificatons
in separate patches to make it easier to review and understand
- 1 notification for delete when using prefix/length; 1 notification for
append
- handle delete of a single nexthop without RTA_MULTIPATH in delete request
- upated commit messages and cover letter
v3
- removed the need for a user API to opt-in to change. Requiring an
API just shifts the difference from same API with different
behavior to different API to achieve equivalent behavior
- route notifications changed to use RTA_MULTIPATH for add and replace
- upated commit messages and cover letter
v2
- fixed locking in patch 1 as noted by DaveM
- changed user API for patch 2 to require an rtmsg with RTM_F_ALL_NEXTHOPS
set in rtm_flags
- revamped explanation of patch 2 and cover letter
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ip6_print_replace_route_err logs an error if a route replace fails with
IPv6 addresses in the full format. e.g,:
IPv6: IPV6: multipath route replace failed (check consistency of installed routes): 2001:0db8:0200:0000:0000:0000:0000:0000 nexthop 2001:0db8:0001:0000:0000:0000:0000:0016 ifi 0
Change the message to dump the addresses in the compressed format.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If an entire multipath route is deleted using prefix and len (without any
nexthops), send a single RTM_DELROUTE notification with the full route
using RTA_MULTIPATH. This is done by generating the skb before the route
delete when all of the sibling routes are still present but sending it
after the route has been removed from the FIB. The skip_notify flag
is used to tell the lower fib code not to send notifications for the
individual nexthop routes.
If a route is deleted using RTA_MULTIPATH for any nexthops or a single
nexthop entry is deleted, then the nexthops are deleted one at a time with
notifications sent as each hop is deleted. This is necessary given that
IPv6 allows individual hops within a route to be deleted.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change ip6_route_multipath_add to send one notifciation with the full
route encoded with RTA_MULTIPATH instead of a series of individual routes.
This is done by adding a skip_notify flag to the nl_info struct. The
flag is used to skip sending of the notification in the fib code that
actually inserts the route. Once the full route has been added, a
notification is generated with all nexthops.
ip6_route_multipath_add handles 3 use cases: new routes, route replace,
and route append. The multipath notification generated needs to be
consistent with the order of the nexthops and it should be consistent
with the order in a FIB dump which means the route with the first nexthop
needs to be used as the route reference. For the first 2 cases (new and
replace), a reference to the route used to send the notification is
obtained by saving the first route added. For the append case, the last
route added is used to loop back to its first sibling route which is
the first nexthop in the multipath route.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IPv6 returns multipath routes as a series of individual routes making
their display and handling by userspace different and more complicated
than IPv4, putting the burden on the user to see that a route is part of
a multipath route and internally creating a multipath route if desired
(e.g., libnl does this as of commit 29b71371e764). This patch addresses
this difference, allowing multipath routes to be returned using the
RTA_MULTIPATH attribute.
The end result is that IPv6 multipath routes can be treated and displayed
in a format similar to IPv4:
$ ip -6 ro ls vrf red
2001:db8:1::/120 dev eth1 proto kernel metric 256 pref medium
2001:db8:2::/120 dev eth2 proto kernel metric 256 pref medium
2001:db8:200::/120 metric 1024
nexthop via 2001:db8:1::2 dev eth1 weight 1
nexthop via 2001:db8:2::2 dev eth2 weight 1
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IPv4 allows multipath routes to be deleted using just the prefix and
length. For example:
$ ip ro ls vrf red
unreachable default metric 8192
1.1.1.0/24
nexthop via 10.100.1.254 dev eth1 weight 1
nexthop via 10.11.200.2 dev eth11.200 weight 1
10.11.200.0/24 dev eth11.200 proto kernel scope link src 10.11.200.3
10.100.1.0/24 dev eth1 proto kernel scope link src 10.100.1.3
$ ip ro del 1.1.1.0/24 vrf red
$ ip ro ls vrf red
unreachable default metric 8192
10.11.200.0/24 dev eth11.200 proto kernel scope link src 10.11.200.3
10.100.1.0/24 dev eth1 proto kernel scope link src 10.100.1.3
The same notation does not work with IPv6 because of how multipath routes
are implemented for IPv6. For IPv6 only the first nexthop of a multipath
route is deleted if the request contains only a prefix and length. This
leads to unnecessary complexity in userspace dealing with IPv6 multipath
routes.
This patch allows all nexthops to be deleted without specifying each one
in the delete request. Internally, this is done by walking the sibling
list of the route matching the specifications given (prefix, length,
metric, protocol, etc).
$ ip -6 ro ls vrf red
2001:db8:1::/120 dev eth1 proto kernel metric 256 pref medium
2001:db8:2::/120 dev eth2 proto kernel metric 256 pref medium
2001:db8:200::/120 via 2001:db8:1::2 dev eth1 metric 1024 pref medium
2001:db8:200::/120 via 2001:db8:2::2 dev eth2 metric 1024 pref medium
...
$ ip -6 ro del vrf red 2001:db8:200::/120
$ ip -6 ro ls vrf red
2001:db8:1::/120 dev eth1 proto kernel metric 256 pref medium
2001:db8:2::/120 dev eth2 proto kernel metric 256 pref medium
...
Because IPv6 allows individual nexthops to be deleted without deleting
the entire route, the ip6_route_multipath_del and non-multipath code
path (ip6_route_del) have to be discriminated so that all nexthops are
only deleted for the latter case. This is done by making the existing
fc_type in fib6_config a u16 and then adding a new u16 field with
fc_delete_all_nh as the first bit.
Suggested-by: Dinesh Dutt <ddutt@cumulusnetworks.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
syzkaller found another out of bound access in ip_options_compile(),
or more exactly in cipso_v4_validate()
Fixes: 20e2a8648596 ("cipso: handle CIPSO options correctly when NetLabel is disabled")
Fixes: 446fda4f2682 ("[NetLabel]: CIPSOv4 engine")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Paul Moore <paul@paul-moore.com>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Andrey Konovalov got crashes in __ip_options_echo() when a NULL skb->dst
is accessed.
ipv4_pktinfo_prepare() should not drop the dst if (evil) IP options
are present.
We could refine the test to the presence of ts_needtime or srr,
but IP options are not often used, so let's be conservative.
Thanks to syzkaller team for finding this bug.
Fixes: d826eb14ecef ("ipv4: PKTINFO doesnt need dst reference")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit 364b6055738b ("net: busy-poll: return busypolling status to
drivers"), napi_complete_done() returns a boolean that can be used
by drivers to conditionally rearm interrupts.
This patch changes virtio_net to use this boolean to avoid a bit of
overhead for busy-poll users.
Jason reports about 1.1% improvement for 1 byte TCP_RR (burst 100).
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enable ring 3 MONITOR/MWAIT for Intel Xeon Phi codenamed Knights Mill. We
can't guarantee that this (KNM) will be the last CPU model that needs this
hack. But, we do recognize that this is far from optimal, and there is an
effort to ensure we don't keep doing extending this hack forever.
Signed-off-by: Piotr Luc <piotr.luc@intel.com>
Cc: Piotr.Luc@intel.com
Cc: dave.hansen@linux.intel.com
Link: http://lkml.kernel.org/r/1484918557-15481-6-git-send-email-grzegorz.andrejczuk@intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
When vmemmap_populate() allocates space for the memmap it does so in 2MB
sized chunks. The libnvdimm-pfn driver incorrectly accounts for this
when the alignment of the device is set to 4K. When this happens we
trigger memory allocation failures in altmap_alloc_block_buf() and
trigger warnings of the form:
WARNING: CPU: 0 PID: 3376 at arch/x86/mm/init_64.c:656 arch_add_memory+0xe4/0xf0
[..]
Call Trace:
dump_stack+0x86/0xc3
__warn+0xcb/0xf0
warn_slowpath_null+0x1d/0x20
arch_add_memory+0xe4/0xf0
devm_memremap_pages+0x29b/0x4e0
Fixes: 315c562536c4 ("libnvdimm, pfn: add 'align' attribute, default to HPAGE_SIZE")
Cc: <stable@vger.kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
1736f75d35e47409ad776273133d0f558a4c8253 is a (v2) patch which had
unresolved review comments[1]. Address the comments by removing the use
of macros from the consumer header (this patch represents the diff
between v2 and v3[2]).
[1] https://lkml.org/lkml/2017/1/26/337
[2] https://lkml.org/lkml/2017/1/26/786
Fixes: 1736f75d35e4 ("gpio: aspeed: Add banks Y, Z, AA, AB and AC")
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
- Prevent double activation of interrupt lines, which causes problems
on certain interrupt controllers
- Handle the fallout of the above because x86 (ab)uses the activation
function to reconfigure interrupts under the hood.
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/irq: Make irq activate operations symmetric
irqdomain: Avoid activating interrupts more than once
|
|
Pull KVM fix from Radim Krčmář:
"Fix a regression that prevented migration between hosts with different
XSAVE features even if the missing features were not used by the guest
(for stable)"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: do not save guest-unsupported XSAVE state
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are two bugfixes that resolve some reported issues. One in the
firmware loader, that should fix the much-reported problem of crashes
with it. The other is a hyperv fix for a reported regression.
Both have been in linux-next for a week or so with no reported issues"
* tag 'char-misc-4.10-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
Drivers: hv: vmbus: finally fix hv_need_to_signal_on_read()
firmware: fix NULL pointer dereference in __fw_load_abort()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO fixes from Greg KH:
"Here are a few small IIO and one staging driver fix for 4.10-rc7. They
fix some reported issues with the drivers.
All of them have been in linux-next for a week or so with no reported
issues"
* tag 'staging-4.10-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: greybus: timesync: validate platform state callback
iio: dht11: Use usleep_range instead of msleep for start signal
iio: adc: palmas_gpadc: retrieve a valid iio_dev in suspend/resume
iio: health: max30100: fixed parenthesis around FIFO count check
iio: health: afe4404: retrieve a valid iio_dev in suspend/resume
iio: health: afe4403: retrieve a valid iio_dev in suspend/resume
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB fixes for some reported issues, and the usual
number of new device ids for 4.10-rc7.
All of these, except the last new device id, have been in linux-next
for a while with no reported issues"
* tag 'usb-4.10-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: serial: pl2303: add ATEN device ID
usb: gadget: f_fs: Assorted buffer overflow checks.
USB: Add quirk for WORLDE easykey.25 MIDI keyboard
usb: musb: Fix external abort on non-linefetch for musb_irq_work()
usb: musb: Fix host mode error -71 regression
USB: serial: option: add device ID for HP lt2523 (Novatel E371)
USB: serial: qcserial: add Dell DW5570 QDL
|
|
.. at least for unprivileged users. Before we called into the SCSI
ioctl code to allow excemptions for a few SCSI passthrough ioctls,
but this is pretty unsafe and except for this call dm knows nothing
about SCSI ioctls.
As the SCSI ioctl code is now optional, we really don't want to
drag it in for DM, and the exception is not very useful anyway.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@kernel.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2017-02-03
This series contains updates to i40e/i40evf only.
Jake fixes up the driver to not call i40e_vsi_kill_vlan() or
i40e_vsi_add_vlan() when the PVID is set or when the VID is less than 1.
Cleaned up a check which really is not needed since there is no real
reason why we cannot just call i40e_del_mac_all_vlan() directly. Renamed
functions to better reflect their actual purpose and how they function
in a more clear manner.
Bimmy cleans up unused/deprecated macros.
Mitch cleans up unused device ids which were intended for use when
running Linux VF drivers under Hyper-V, but found to be not needed.
Then cleaned up a function that is no longer needed since the client
open and close functions were refactored. Adds a sleep without timeout
until the reply from the PF driver has been received since the iWARP
client cannot continue until the operation has been completed.
Tushar Dave fixes an issue seen on SPARC where the use of the 'packed'
directive was causing kernel unaligned errors.
Alex does a refactor to pull some data off of the stack and store it
in the transmit buffer info section of the transmit ring.
Alan fixes a bug which was caused by passing a bad register value to the
firmware, by refactoring the macro INTRL_USEC_TO_REG into a static
inline function. Also added feedback to the user as to the actual
interrupt rate limit being used when it differs from the requested limit.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To make the code clearer, use rb_entry() instead of open coding it
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Toshi Kani <toshi.kani@hpe.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Link: http://lkml.kernel.org/r/974a91cd4ed2d04c92e4faa4765077e38f248d6b.1482157956.git.geliangtang@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
The driver defaults to voltage, not current, type so correct
this in the device tree binding documentation.
Signed-off-by: Hans Holmberg <hans@pixelmunchies.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Many Motorola phones like droid 4 are using a custom PMIC called CPCAP
or 6556002. This PMIC is used with several SoCs, I've noticed at least
omap3, omap4 and Tegra2 based Motorola phones and tablets using it.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
"re-enable" was misspelled as "reename".
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When performing this bulk operation, there is no need to track every supply
individually. It is more efficient to treat entire group as a single
managed resource.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
There is no need to have two loops there, we can store error for subsequent
reporting.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Instead of separate "exclusive" and "allow_dummy" arguments, that formed 3
valid combinations (normal, exclusive and optional) and an invalid one,
let's accept explicit "get_type", like we did in devm-managed code.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
There is no point in assigning value to 'ret' before calling
regulator_dev_lookup() as it will clobber 'ret' anyway.
Also, let's explicitly return -PROBE_DEFER when try_module_get() fails,
instead of relying that earlier initialization of "regulator" carries
correct value.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Exception handlers which may run on IST stack call ist_enter() at the start
of execution and ist_exit() in the end. ist_enter() disables preemption
unconditionally and ist_exit() enables it.
So the extra preempt_disable/enable() pairs nested inside the
ist_enter/exit() regions are pointless and can be removed.
Signed-off-by: Alexander Kuleshov <kuleshovmail@gmail.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Jianyu Zhan <nasa4836@gmail.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@suse.de>
Link: http://lkml.kernel.org/r/20161128075057.7724-1-kuleshovmail@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
commit 8fd524b355da ("x86: Kill bad_dma_address variable") has killed
bad_dma_address variable and used instead of macro DMA_ERROR_CODE
which is always zero. Since dma_addr is unsigned, the statement
dma_addr >= DMA_ERROR_CODE
is always true, and not needed.
arch/x86/kernel/pci-calgary_64.c: In function ‘iommu_free’:
arch/x86/kernel/pci-calgary_64.c:299:2: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
if (unlikely((dma_addr >= DMA_ERROR_CODE) && (dma_addr < badend))) {
Fixes: 8fd524b355da ("x86: Kill bad_dma_address variable")
Signed-off-by: Nikola Pajkovsky <npajkovsky@suse.cz>
Cc: iommu@lists.linux-foundation.org
Cc: Jon Mason <jdmason@kudzu.us>
Cc: Muli Ben-Yehuda <mulix@mulix.org>
Link: http://lkml.kernel.org/r/7612c0f9dd7c1290407dbf8e809def922006920b.1479161177.git.npajkovsky@suse.cz
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
On a large SMP systems with hundreds of CPUs, the current thresholds
for allocating and freeing debug objects (256 and 1024 respectively)
may not work well. This can cause a lot of needless calls to
kmem_aloc() and kmem_free() on those systems.
To alleviate this thrashing problem, the object freeing threshold
is now increased to "1024 + # of CPUs * 32". Whereas the object
allocation threshold is increased to "256 + # of CPUs * 4". That
should make the debug objects subsystem scale better with the number
of CPUs available in the system.
Signed-off-by: Waiman Long <longman@redhat.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: "Du Changbin" <changbin.du@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jan Stancek <jstancek@redhat.com>
Link: http://lkml.kernel.org/r/1483647425-4135-3-git-send-email-longman@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
New debugfs stat counters are added to track the numbers of
kmem_cache_alloc() and kmem_cache_free() function calls to get a
sense of how the internal debug objects cache management is performing.
Signed-off-by: Waiman Long <longman@redhat.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: "Du Changbin" <changbin.du@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jan Stancek <jstancek@redhat.com>
Link: http://lkml.kernel.org/r/1483647425-4135-2-git-send-email-longman@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
It was observed that on an Intel x86 system without the ARAT (Always
running APIC timer) feature and with fairly large number of CPUs as
well as CPUs coming in and out of intel_idle frequently, the lock
contention on the tick_broadcast_lock can become significant.
To reduce contention, the lock is put into its own cacheline and all
the cpumask_var_t variables are put into the __read_mostly section.
Running the SP benchmark of the NAS Parallel Benchmarks on a 4-socket
16-core 32-thread Nehalam system, the performance number improved
from 3353.94 Mop/s to 3469.31 Mop/s when this patch was applied on
a 4.9.6 kernel. This is a 3.4% improvement.
Signed-off-by: Waiman Long <longman@redhat.com>
Cc: "Peter Zijlstra (Intel)" <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/1485799063-20857-1-git-send-email-longman@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Enable ring 3 MONITOR/MWAIT for Intel Xeon Phi x200 codenamed Knights
Landing.
Presence of this feature cannot be detected automatically (by reading any
other MSR) therefore it is required to explicitly check for the family and
model of the CPU before attempting to enable it.
Signed-off-by: Grzegorz Andrejczuk <grzegorz.andrejczuk@intel.com>
Cc: Piotr.Luc@intel.com
Cc: dave.hansen@linux.intel.com
Link: http://lkml.kernel.org/r/1484918557-15481-5-git-send-email-grzegorz.andrejczuk@intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Add software-defined CPUID bit for the non-architectural ring 3
MONITOR/MWAIT feature.
Signed-off-by: Grzegorz Andrejczuk <grzegorz.andrejczuk@intel.com>
Cc: Piotr.Luc@intel.com
Cc: dave.hansen@linux.intel.com
Link: http://lkml.kernel.org/r/1484918557-15481-4-git-send-email-grzegorz.andrejczuk@intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Introduce ELF_HWCAP2 variable for x86 and reserve its bit 0 to expose the
ring 3 MONITOR/MWAIT.
HWCAP variables contain bitmasks which can be used by userspace
applications to detect which instruction sets are supported by CPU. On x86
architecture information about CPU capabilities can be checked via CPUID
instructions, unfortunately presence of ring 3 MONITOR/MWAIT feature cannot
be checked this way. ELF_HWCAP cannot be used as well, because on x86 it is
set to CPUID[1].EDX which means that all bits are reserved there.
HWCAP2 approach was chosen because it reuses existing solution present
in other architectures, so only minor modifications are required to the
kernel and userspace applications. When ELF_HWCAP2 is defined
kernel maps it to AT_HWCAP2 during the start of the application.
This way the ring 3 MONITOR/MWAIT feature can be detected using getauxval()
API in a simple and fast manner. ELF_HWCAP2 type is u32 to be consistent
with x86 ELF_HWCAP type.
Signed-off-by: Grzegorz Andrejczuk <grzegorz.andrejczuk@intel.com>
Cc: Piotr.Luc@intel.com
Cc: dave.hansen@linux.intel.com
Link: http://lkml.kernel.org/r/1484918557-15481-3-git-send-email-grzegorz.andrejczuk@intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Define new MSR MISC_FEATURE_ENABLES (0x140).
On supported CPUs if bit 1 of this MSR is set, then calling MONITOR and
MWAIT instructions outside of ring 0 will not cause invalid-opcode
exception.
The MSR MISC_FEATURE_ENABLES is not yet documented in the SDM. Here is the
relevant documentation:
Hex Dec Name Scope
140H 320 MISC_FEATURE_ENABLES Thread
0 Reserved
1 If set to 1, the MONITOR and MWAIT instructions do not
cause invalid-opcode exceptions when executed with CPL > 0
or in virtual-8086 mode. If MWAIT is executed when CPL > 0
or in virtual-8086 mode, and if EAX indicates a C-state
other than C0 or C1, the instruction operates as if EAX
indicated the C-state C1.
63:2 Reserved
Signed-off-by: Grzegorz Andrejczuk <grzegorz.andrejczuk@intel.com>
Cc: Piotr.Luc@intel.com
Cc: dave.hansen@linux.intel.com
Link: http://lkml.kernel.org/r/1484918557-15481-2-git-send-email-grzegorz.andrejczuk@intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fix from James Bottomley:
"A single fix this time: a fix for a virtqueue removal bug which only
appears to affect S390, but which results in the queue hanging forever
thus causing the machine to fail shutdown"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: virtio_scsi: Reject commands when virtqueue is broken
|
|
- s/freqnency/frequency/
- s/accomodating/accommodating/
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The might_sleep_if() assertions in __pm_runtime_idle(),
__pm_runtime_suspend() and __pm_runtime_resume() may generate
false-positive warnings in some situations. For example, that
happens if a nested pm_runtime_get_sync()/pm_runtime_put() pair
is executed with disabled interrupts within an outer
pm_runtime_get_sync()/pm_runtime_put() section for the same device.
[Generally, pm_runtime_get_sync() may sleep, so it should not be
called with disabled interrupts, but in this particular case the
previous pm_runtime_get_sync() guarantees that the device will not
be suspended, so the inner pm_runtime_get_sync() will return
immediately after incrementing the device's usage counter.]
That started to happen in the i915 driver in 4.10-rc, leading to
the following splat:
BUG: sleeping function called from invalid context at drivers/base/power/runtime.c:1032
in_atomic(): 1, irqs_disabled(): 0, pid: 1500, name: Xorg
1 lock held by Xorg/1500:
#0: (&dev->struct_mutex){+.+.+.}, at:
[<ffffffffa0680c13>] i915_mutex_lock_interruptible+0x43/0x140 [i915]
CPU: 0 PID: 1500 Comm: Xorg Not tainted
Call Trace:
dump_stack+0x85/0xc2
___might_sleep+0x196/0x260
__might_sleep+0x53/0xb0
__pm_runtime_resume+0x7a/0x90
intel_runtime_pm_get+0x25/0x90 [i915]
aliasing_gtt_bind_vma+0xaa/0xf0 [i915]
i915_vma_bind+0xaf/0x1e0 [i915]
i915_gem_execbuffer_relocate_entry+0x513/0x6f0 [i915]
i915_gem_execbuffer_relocate_vma.isra.34+0x188/0x250 [i915]
? trace_hardirqs_on+0xd/0x10
? i915_gem_execbuffer_reserve_vma.isra.31+0x152/0x1f0 [i915]
? i915_gem_execbuffer_reserve.isra.32+0x372/0x3a0 [i915]
i915_gem_do_execbuffer.isra.38+0xa70/0x1a40 [i915]
? __might_fault+0x4e/0xb0
i915_gem_execbuffer2+0xc5/0x260 [i915]
? __might_fault+0x4e/0xb0
drm_ioctl+0x206/0x450 [drm]
? i915_gem_execbuffer+0x340/0x340 [i915]
? __fget+0x5/0x200
do_vfs_ioctl+0x91/0x6f0
? __fget+0x111/0x200
? __fget+0x5/0x200
SyS_ioctl+0x79/0x90
entry_SYSCALL_64_fastpath+0x23/0xc6
even though the code triggering it is correct.
Unfortunately, the might_sleep_if() assertions in question are
too coarse-grained to cover such cases correctly, so make them
a bit less sensitive in order to avoid the false-positives.
Reported-and-tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Pull virtio/vhost fixes from Michael S. Tsirkin:
"Last minute fixes:
- ARM DMA fix revert
- vhost endian-ness fix
- MAINTAINERS: email address change for Amit"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
MAINTAINERS: update email address for Amit Shah
vhost: fix initialization for vq->is_le
Revert "vring: Force use of DMA API for ARM-based systems with legacy devices"
|
|
Pull VFIO fix from Alex Williamson:
"Fix an error path in SPAPR IOMMU backend (Alexey Kardashevskiy)"
* tag 'vfio-v4.10-rc7' of git://github.com/awilliam/linux-vfio:
vfio/spapr: Fix missing mutex unlock when creating a window
|
|
Some Kabylake desktop processors may not reach max turbo when running in
HWP mode, even if running under sustained 100% utilization.
This occurs when the HWP.EPP (Energy Performance Preference) is set to
"balance_power" (0x80) -- the default on most systems.
It occurs because the platform BIOS may erroneously enable an
energy-efficiency setting -- MSR_IA32_POWER_CTL BIT-EE, which is not
recommended to be enabled on this SKU.
On the failing systems, this BIOS issue was not discovered when the
desktop motherboard was tested with Windows, because the BIOS also
neglects to provide the ACPI/CPPC table, that Windows requires to enable
HWP, and so Windows runs in legacy P-state mode, where this setting has
no effect.
Linux' intel_pstate driver does not require ACPI/CPPC to enable HWP, and
so it runs in HWP mode, exposing this incorrect BIOS configuration.
There are several ways to address this problem.
First, Linux can also run in legacy P-state mode on this system.
As intel_pstate is how Linux enables HWP, booting with
"intel_pstate=disable"
will run in acpi-cpufreq/ondemand legacy p-state mode.
Or second, the "performance" governor can be used with intel_pstate,
which will modify HWP.EPP to 0.
Or third, starting in 4.10, the
/sys/devices/system/cpu/cpufreq/policy*/energy_performance_preference
attribute in can be updated from "balance_power" to "performance".
Or fourth, apply this patch, which fixes the erroneous setting of
MSR_IA32_POWER_CTL BIT_EE on this model, allowing the default
configuration to function as designed.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Reviewed-by: Len Brown <len.brown@intel.com>
Cc: 4.6+ <stable@vger.kernel.org> # 4.6+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
When HWP is active, turbo activation ratio is not used to calculate max
non turbo ratio. But on these systems the max non turbo ratio is decided
by config TDP settings.
This change removes usage of MSR_TURBO_ACTIVATION_RATIO for HWP systems,
instead directly use TDP ratios, when more than one TDPs are available.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Under HWP the performance limits are calculated using max_perf_pct
and min_perf_pct using possible performance, not available performance.
The available performance can be reduced by no_turbo setting. To make
compatible with legacy mode, use max/min performance percentage with
respect to available performance.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
When turbo is not disabled by BIOS, but user disabled from intel P-State
sysfs and changes max/min using cpufreq sysfs, the resultant frequency
is lower than what user requested.
The reason for this, when the perf limits are calculated in set_policy()
callback, they are with reference to max cpu frequency (turbo frequency
), but when enforced in the intel_pstate_get_min_max() they are with
reference to max available performance as documented in the intel_pstate
documentation (in this case max non turbo P-State).
This needs similar change as done in intel_cpufreq_verify_policy() for
passive mode. Set policy->cpuinfo.max_freq based on the turbo status.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Make it possible to change the operation mode of intel_pstate with
the help of a new sysfs attribute called "status".
There are three possible configurations that can be selected using
this attribute:
"off" - The driver is not in use at this time.
"active" - The driver works as a P-state governor (default).
"passive" - The driver works as a regular cpufreq one and collaborates
with the generic cpufreq governors (it sets P-states as
requested by those governors). [This is the same mode
the driver can be started in by passing intel_pstate=passive
in the kernel command line.]
The current setting is returned by reads from this attribute. Writing
one of the above strings to it changes the operation mode as indicated
by that string, if possible.
If HW-managed P-states (HWP) feature is enabled, it is not possible
to change the driver's operation mode and attempts to write to this
attribute will fail.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Expose the intel_pstate's global sysfs attributes before registering
the driver to prepare for the addition of an attribute that also will
have to work if the driver is not registered.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Its not used anymore, remove it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
acpi_processor_ppc_notifier() can live without using CPUFREQ_START
(which is gonna be removed soon), as it is only used while setting
ignore_ppc to 0. This can be done with the help of "ignore_ppc < 0"
check alone. The notifier function anyway ignores all events except
CPUFREQ_ADJUST and dropping CPUFREQ_START wouldn't harm at all.
Once CPUFREQ_START event is removed from the cpufreq core,
acpi_processor_ppc_notifier() will get called only for CPUFREQ_NOTIFY or
CPUFREQ_ADJUST event. Drop the return statement from the first if block
to make sure we don't ignore any such events.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
