| Age | Commit message (Collapse) | Author |
|---|
|
Calling mac_reset() on a Mac IIci does reset the system, but what
follows is a POST failure that requires a manual reset to resolve.
Avoid that by using the 68030 asm implementation instead of the C
implementation.
Apparently the SE/30 has a similar problem as it has used the asm
implementation since before git. This patch extends that solution to
other systems with a similar ROM.
After this patch, the only systems still using the C implementation are
68040 systems where adb_type is either MAC_ADB_IOP or MAC_ADB_II. This
implies a 1 MiB Quadra ROM.
This now includes the Quadra 900/950, which previously fell through to
the "should never get here" catch-all.
Reported-and-tested-by: Stan Johnson <userm57@yahoo.com>
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Finn Thain <fthain@linux-m68k.org>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/480ebd1249d229c6dc1f3f1c6d599b8505483fd8.1714797072.git.fthain@linux-m68k.org
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
|
Context switching does take care to retain the correct lock owner across
the switch from 'prev' to 'next' tasks. This does rely on interrupts
remaining disabled for the entire duration of the switch.
This condition is guaranteed for normal process creation and context
switching between already running processes, because both 'prev' and
'next' already have interrupts disabled in their saved copies of the
status register.
The situation is different for newly created kernel threads. The status
register is set to PS_S in copy_thread(), which does leave the IPL at 0.
Upon restoring the 'next' thread's status register in switch_to() aka
resume(), interrupts then become enabled prematurely. resume() then
returns via ret_from_kernel_thread() and schedule_tail() where run queue
lock is released (see finish_task_switch() and finish_lock_switch()).
A timer interrupt calling scheduler_tick() before the lock is released
in finish_task_switch() will find the lock already taken, with the
current task as lock owner. This causes a spinlock recursion warning as
reported by Guenter Roeck.
As far as I can ascertain, this race has been opened in commit
533e6903bea0 ("m68k: split ret_from_fork(), simplify kernel_thread()")
but I haven't done a detailed study of kernel history so it may well
predate that commit.
Interrupts cannot be disabled in the saved status register copy for
kernel threads (init will complain about interrupts disabled when
finally starting user space). Disable interrupts temporarily when
switching the tasks' register sets in resume().
Note that a simple oriw 0x700,%sr after restoring sr is not enough here
- this leaves enough of a race for the 'spinlock recursion' warning to
still be observed.
Tested on ARAnyM and qemu (Quadra 800 emulation).
Fixes: 533e6903bea0 ("m68k: split ret_from_fork(), simplify kernel_thread()")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Closes: https://lore.kernel.org/all/07811b26-677c-4d05-aeb4-996cd880b789@roeck-us.net
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20240411033631.16335-1-schmitzmic@gmail.com
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
|
In a future patch HAS_IOPORT=n will disable inb()/outb() and friends at
compile time. With that choosing dynamically between I/O port and MMIO
access via GNERIC_IOMAP will not work. So only select GENERIC_IOMAP when
HAS_IOPORT is selected.
Co-developed-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20240403122851.38808-2-schnelle@linux.ibm.com
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
|
This macro has the advantage over SET_SYSTEM_SLEEP_PM_OPS that we don't
have to care about when the functions are actually used.
Also make use of pm_sleep_ptr() to discard all PM_SLEEP related
stuff if CONFIG_PM_SLEEP isn't enabled.
Link: https://lore.kernel.org/lkml/20240417044459.1908-2-linux.amoon@gmail.com/
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
|
|
David Howells says:
====================
rxrpc: Miscellaneous fixes (part)
Here some miscellaneous fixes for AF_RXRPC:
(1) Fix the congestion control algorithm to start cwnd at 4 and to not cut
ssthresh when the peer cuts its rwind size.
(2) Only transmit a single ACK for all the DATA packets glued together
into a jumbo packet to reduce the number of ACKs being generated.
====================
Link: https://lore.kernel.org/r/20240503150749.1001323-1-dhowells@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Only generate one ACK packet for all the subpackets in a jumbo packet. If
we would like to generate more than one ACK, we prioritise them base on
their reason code, in the order, highest first:
OutOfSeq > NoSpace > ExceedsWin > Duplicate > Requested > Delay > Idle
For the first four, we reference the lowest offending subpacket; for the
last three, the highest.
This reduces the number of ACKs we end up transmitting to one per UDP
packet transmitted to reduce network loading and packet parsing.
Fixes: 5d7edbc9231e ("rxrpc: Get rid of the Rx ring")
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Reviewed-by: Jeffrey Altman <jaltman@auristor.com <mailto:jaltman@auristor.com>>
Link: https://lore.kernel.org/r/20240503150749.1001323-3-dhowells@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Make the following fixes to the congestion control algorithm:
(1) Don't vary the cwnd starting value by the size of RXRPC_TX_SMSS since
that's currently held constant - set to the size of a jumbo subpacket
payload so that we can create jumbo packets on the fly. The current
code invariably picks 3 as the starting value.
Further, the starting cwnd needs to be an even number because we ack
every other packet, so set it to 4.
(2) Don't cut ssthresh when we see an ACK come from the peer with a
receive window (rwind) less than ssthresh. ssthresh keeps track of
characteristics of the connection whereas rwind may be reduced by the
peer for any reason - and may be reduced to 0.
Fixes: 1fc4fa2ac93d ("rxrpc: Fix congestion management")
Fixes: 0851115090a3 ("rxrpc: Reduce ssthresh to peer's receive window")
Signed-off-by: David Howells <dhowells@redhat.com>
Suggested-by: Simon Wilkinson <sxw@auristor.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Reviewed-by: Jeffrey Altman <jaltman@auristor.com <mailto:jaltman@auristor.com>>
Link: https://lore.kernel.org/r/20240503150749.1001323-2-dhowells@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
|
|
When LSE atomics are available, BPF atomic instructions are implemented
as single ARM64 atomic instructions, therefore it is easy to enable
these in bpf_arena using the currently available exception handling
setup.
LL_SC atomics use loops and therefore would need more work to enable in
bpf_arena.
Enable LSE atomics based instructions in bpf_arena and use the
bpf_jit_supports_insn() callback to reject atomics in bpf_arena if LSE
atomics are not available.
All atomics and arena_atomics selftests are passing:
[root@ip-172-31-2-216 bpf]# ./test_progs -a atomics,arena_atomics
#3/1 arena_atomics/add:OK
#3/2 arena_atomics/sub:OK
#3/3 arena_atomics/and:OK
#3/4 arena_atomics/or:OK
#3/5 arena_atomics/xor:OK
#3/6 arena_atomics/cmpxchg:OK
#3/7 arena_atomics/xchg:OK
#3 arena_atomics:OK
#10/1 atomics/add:OK
#10/2 atomics/sub:OK
#10/3 atomics/and:OK
#10/4 atomics/or:OK
#10/5 atomics/xor:OK
#10/6 atomics/cmpxchg:OK
#10/7 atomics/xchg:OK
#10 atomics:OK
Summary: 2/14 PASSED, 0 SKIPPED, 0 FAILED
Signed-off-by: Puranjay Mohan <puranjay@kernel.org>
Link: https://lore.kernel.org/r/20240426161116.441-1-puranjay@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
If we're updating an existing slot, we clear the slot bitmap only to
set it again right after. Just leave the bit set rather than toggle
it off and on, and move the unused slot setting into the branch of
not already having a file occupy this slot.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
When creating the topology for the test, three veth pairs are created in
the initial network namespace before being moved to one of the network
namespaces created by the test.
On systems where systemd-udev uses MACAddressPolicy=persistent (default
since systemd version 242), this will result in some net devices having
the same MAC address since they were created with the same name in the
initial network namespace. In turn, this leads to arping / ndisc6
failing since packets are dropped by the bridge's loopback filter.
Fix by creating each net device in the correct network namespace instead
of moving it there from the initial network namespace.
Reported-by: Jakub Kicinski <kuba@kernel.org>
Closes: https://lore.kernel.org/netdev/20240426074015.251854d4@kernel.org/
Fixes: 7648ac72dcd7 ("selftests: net: Add bridge neighbor suppression test")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/20240507113033.1732534-1-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
It is possible that the host connected and saw a cm established
event and started sending nvme capsules on the qp, however the
ctrl did not yet see an established event. This is why the
rsp_wait_list exists (for async handling of these cmds, we move
them to a pending list).
Furthermore, it is possible that the ctrl cm times out, resulting
in a connect-error cm event. in this case we hit a bad deref [1]
because in nvmet_rdma_free_rsps we assume that all the responses
are in the free list.
We are freeing the cmds array anyways, so don't even bother to
remove the rsp from the free_list. It is also guaranteed that we
are not racing anything when we are releasing the queue so no
other context accessing this array should be running.
[1]:
--
Workqueue: nvmet-free-wq nvmet_rdma_free_queue_work [nvmet_rdma]
[...]
pc : nvmet_rdma_free_rsps+0x78/0xb8 [nvmet_rdma]
lr : nvmet_rdma_free_queue_work+0x88/0x120 [nvmet_rdma]
Call trace:
nvmet_rdma_free_rsps+0x78/0xb8 [nvmet_rdma]
nvmet_rdma_free_queue_work+0x88/0x120 [nvmet_rdma]
process_one_work+0x1ec/0x4a0
worker_thread+0x48/0x490
kthread+0x158/0x160
ret_from_fork+0x10/0x18
--
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
lapic_vector_set_in_irr() is already available, use it for checking
pending vectors at the local APIC. No functional change.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Imran Khan <imran.f.khan@oracle.com>
Link: https://lore.kernel.org/r/20240506175612.1141095-1-jacob.jun.pan@linux.intel.com
|
|
The nsid value is a u32 that comes from nvmet_req_find_ns(). It's
endian data and we're on an error path and both of those raise red
flags. So let's make this safer.
1) Make the buffer large enough for any u32.
2) Remove the unnecessary initialization.
3) Use snprintf() instead of sprintf() for even more safety.
4) The sprintf() function returns the number of bytes printed, not
counting the NUL terminator. It is impossible for the return value to
be <= 0 so delete that.
Fixes: 505363957fad ("nvmet: fix nvme status code when namespace is disabled")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
Only four lcluster types here, remove redundant code.
No real logic changes.
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Link: https://lore.kernel.org/r/20240508123357.3266173-1-hsiangkao@linux.alibaba.com
|
|
The number of updated CPU capabilities per netlink event is hard-coded to
16. On systems with more than 16 CPUs (a common case), it takes more than
one thermal netlink event to relay all the new capabilities after an HFI
interrupt. This adds unnecessary overhead to both the kernel and user space
entities.
Increase the number of CPU capabilities updated per event to 64. Any system
with 64 CPUs or less can now update all the capabilities in a single
thermal netlink event.
Signed-off-by: Ricardo Neri <ricardo.neri-calderon@linux.intel.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
When processing a hardware update, HFI generates as many thermal netlink
events as needed to relay all the updated CPU capabilities to user space.
The constant HFI_MAX_THERM_NOTIFY_COUNT is the number of CPU capabilities
updated per each of those events.
Give this constant a more descriptive name.
Signed-off-by: Ricardo Neri <ricardo.neri-calderon@linux.intel.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The delay between an HFI interrupt and its corresponding thermal netlink
event has so far been hard-coded to CONFIG_HZ jiffies (1 second). This
delay is too long for hardware that generates updates every tens of
milliseconds.
The HFI driver uses a delayed workqueue to send thermal netlink events. No
subsequent events will be sent if there is pending work.
As a result, much of the information of consecutive hardware updates will
be lost if the workqueue delay is too long. User space entities may act on
obsolete data. If the delay is too short, multiple events may overwhelm
listeners.
Set the delay to 100ms to strike a balance between too many and too few
events. Use milliseconds instead of jiffies to improve readability.
Signed-off-by: Ricardo Neri <ricardo.neri-calderon@linux.intel.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The name of the constant HFI_UPDATE_INTERVAL is misleading. It is not a
periodic interval at which HFI updates are processed. It is the delay in
the processing of an HFI update after the arrival of an HFI interrupt.
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Ricardo Neri <ricardo.neri-calderon@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
To address the performance drop issue, an optimization has been
implemented. The incorrect highest performance value previously set by the
low-level power firmware for AMD CPUs with Family ID 0x19 and Model ID
ranging from 0x70 to 0x7F series has been identified as the cause.
To resolve this, a check has been implemented to accurately determine the
CPU family and model ID. The correct highest performance value is now set
and the performance drop caused by the incorrect highest performance value
are eliminated.
Before the fix, the highest frequency was set to 4200MHz, now it is set
to 4971MHz which is correct.
CPU NODE SOCKET CORE L1d:L1i:L2:L3 ONLINE MAXMHZ MINMHZ MHZ
0 0 0 0 0:0:0:0 yes 4971.0000 400.0000 400.0000
1 0 0 0 0:0:0:0 yes 4971.0000 400.0000 400.0000
2 0 0 1 1:1:1:0 yes 4971.0000 400.0000 4865.8140
3 0 0 1 1:1:1:0 yes 4971.0000 400.0000 400.0000
Fixes: f3a052391822 ("cpufreq: amd-pstate: Enable amd-pstate preferred core support")
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218759
Signed-off-by: Perry Yuan <perry.yuan@amd.com>
Co-developed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Tested-by: Gaha Bana <gahabana@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Without this change the created netns instances are not cleared after
this script execution. To fix this problem the cleanup_all_ns function
from ../lib.sh is called.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the explicit call to "return" in the void ax25_ds_set_timer
function that was introduced in 78a7b5dbc060 ("ax.25: x.25: Remove the
now superfluous sentinel elements from ctl_table array").
Signed-off-by: Joel Granados <j.granados@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Let's make all IPVS sysctls writtable even when
network namespace is owned by non-initial user namespace.
Let's make a few sysctls to be read-only for non-privileged users:
- sync_qlen_max
- sync_sock_size
- run_estimation
- est_cpulist
- est_nice
I'm trying to be conservative with this to prevent
introducing any security issues in there. Maybe,
we can allow more sysctls to be writable, but let's
do this on-demand and when we see real use-case.
This patch is motivated by user request in the LXC
project [1]. Having this can help with running some
Kubernetes [2] or Docker Swarm [3] workloads inside the system
containers.
Link: https://github.com/lxc/lxc/issues/4278 [1]
Link: https://github.com/kubernetes/kubernetes/blob/b722d017a34b300a2284b890448e5a605f21d01e/pkg/proxy/ipvs/proxier.go#L103 [2]
Link: https://github.com/moby/libnetwork/blob/3797618f9a38372e8107d8c06f6ae199e1133ae8/osl/namespace_linux.go#L682 [3]
Cc: Julian Anastasov <ja@ssi.bg>
Cc: Simon Horman <horms@verge.net.au>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: Jozsef Kadlecsik <kadlec@netfilter.org>
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: Alexander Mikhalitsyn <aleksandr.mikhalitsyn@canonical.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cc: Julian Anastasov <ja@ssi.bg>
Cc: Simon Horman <horms@verge.net.au>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: Jozsef Kadlecsik <kadlec@netfilter.org>
Cc: Florian Westphal <fw@strlen.de>
Suggested-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Alexander Mikhalitsyn <aleksandr.mikhalitsyn@canonical.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As it was done in commit fc1092f51567 ("ipv4: Fix uninit-value access in
__ip_make_skb()") for IPv4, check FLOWI_FLAG_KNOWN_NH on fl6->flowi6_flags
instead of testing HDRINCL on the socket to avoid a race condition which
causes uninit-value access.
Fixes: ea30388baebc ("ipv6: Fix an uninit variable access bug in __ip6_make_skb()")
Signed-off-by: Shigeru Yoshida <syoshida@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the ipq806x dwmac driver is almost always used attached to the
CPU port of a switch and phy-mode was always set to "rgmii" or "sgmii".
Some device came up with a special configuration where the PHY is
directly attached to the GMAC port and in those case phy-mode needs to
be set to "rgmii-id" to make the PHY correctly work and receive packets.
Since the driver supports only "rgmii" and "sgmii" mode, when "rgmii-id"
(or variants) mode is set, the mode is rejected and probe fails.
Add support also for these phy-modes to correctly setup PHYs that requires
delay applied to tx/rx.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enhance the error reporting mechanism in the switchdev framework to
provide more informative and user-friendly error messages.
Following feedback from users struggling to understand the implications
of error messages like "failed (err=-28) to add object (id=2)", this
update aims to clarify what operation failed and how this might impact
the system or network.
With this change, error messages now include a description of the failed
operation, the specific object involved, and a brief explanation of the
potential impact on the system. This approach helps administrators and
developers better understand the context and severity of errors,
facilitating quicker and more effective troubleshooting.
Example of the improved logging:
[ 70.516446] ksz-switch spi0.0 uplink: Failed to add Port Multicast
Database entry (object id=2) with error: -ENOSPC (-28).
[ 70.516446] Failure in updating the port's Multicast Database could
lead to multicast forwarding issues.
[ 70.516446] Current HW/SW setup lacks sufficient resources.
This comprehensive update includes handling for a range of switchdev
object IDs, ensuring that most operations within the switchdev framework
benefit from clearer error reporting.
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Different revisions of the Marvell 88q2xxx phy needs different init
sequences.
Add init sequence for Rev B1 and Rev B2. Rev B2 init sequence skips one
register write.
Tested-by: Dimitri Fedrau <dima.fedrau@gmail.com>
Signed-off-by: Gregor Herburger <gregor.herburger@ew.tq-group.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a broadcast AppleTalk packet is received, prefer queuing it on the
socket whose address matches the address of the interface that received
the packet (and is listening on the correct port). Userspace
applications that handle such packets will usually send a response on
the same socket that received the packet; this fix allows the response
to be sent on the correct interface.
If a socket matching the interface's address is not found, an arbitrary
socket listening on the correct port will be used, if any. This matches
the implementation's previous behavior.
Fixes atalkd's responses to network information requests when multiple
network interfaces are configured to use AppleTalk.
Link: https://lore.kernel.org/netdev/20200722113752.1218-2-vincent.ldev@duvert.net/
Link: https://gist.github.com/VinDuv/4db433b6dce39d51a5b7847ee749b2a4
Signed-off-by: Vincent Duvert <vincent.ldev@duvert.net>
Signed-off-by: Doug Brown <doug@schmorgal.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce a tracepoint for icmp_send, which can help users to get more
detail information conveniently when icmp abnormal events happen.
1. Giving an usecase example:
=============================
When an application experiences packet loss due to an unreachable UDP
destination port, the kernel will send an exception message through the
icmp_send function. By adding a trace point for icmp_send, developers or
system administrators can obtain detailed information about the UDP
packet loss, including the type, code, source address, destination address,
source port, and destination port. This facilitates the trouble-shooting
of UDP packet loss issues especially for those network-service
applications.
2. Operation Instructions:
==========================
Switch to the tracing directory.
cd /sys/kernel/tracing
Filter for destination port unreachable.
echo "type==3 && code==3" > events/icmp/icmp_send/filter
Enable trace event.
echo 1 > events/icmp/icmp_send/enable
3. Result View:
================
udp_client_erro-11370 [002] ...s.12 124.728002:
icmp_send: icmp_send: type=3, code=3.
From 127.0.0.1:41895 to 127.0.0.1:6666 ulen=23
skbaddr=00000000589b167a
Signed-off-by: Peilin He <he.peilin@zte.com.cn>
Signed-off-by: xu xin <xu.xin16@zte.com.cn>
Reviewed-by: Yunkai Zhang <zhang.yunkai@zte.com.cn>
Cc: Yang Yang <yang.yang29@zte.com.cn>
Cc: Liu Chun <liu.chun2@zte.com.cn>
Cc: Xuexin Jiang <jiang.xuexin@zte.com.cn>
Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The change from skb_copy to pskb_copy unfortunately changed the data
copying to omit the ethernet header, since it was pulled before reaching
this point. Fix this by calling __skb_push/pull around pskb_copy.
Fixes: 59c878cbcdd8 ("net: bridge: fix multicast-to-unicast with fraglist GSO")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Oleksij Rempel says:
====================
add DCB and DSCP support for KSZ switches
This patch series is aimed at improving support for DCB (Data Center
Bridging) and DSCP (Differentiated Services Code Point) on KSZ switches.
The main goal is to introduce global DSCP and PCP (Priority Code Point)
mapping support, addressing the limitation of KSZ switches not having
per-port DSCP priority mapping. This involves extending the DSA
framework with new callbacks for managing trust settings for global DSCP
and PCP maps. Additionally, we introduce IEEE 802.1q helpers for default
configurations, benefiting other drivers too.
Change logs are in separate patches.
Compared to v6 this series includes some new patches for DSCP global
mapping support and QoS selftest script for KSZ9477 switches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add tests covering following functionality on KSZ9477 switch family:
- default port priority
- global DSCP to Internal Priority Mapping
- apptrust configuration
This script was tested on KSZ9893R
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Microchip KSZ and LAN variants do not have per port DSCP priority
configuration. Instead there is a global DSCP mapping table.
This patch provides write access to this global DSCP map. In case entry
is "deleted", we map corresponding DSCP entry to a best effort prio,
which is expected to be the default priority for all untagged traffic.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some switches like Microchip KSZ variants do not support per port DSCP
priority configuration. Instead there is a global DSCP mapping table.
To handle it, we will accept set/del request to any of user ports to
make global configuration and update dcb app entries for all other
ports.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
802.1P (PCP) and DiffServ (DSCP) are handled now by DCB code. Let it do
all needed initial configuration.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
KSZ8xxx variants
Init priority to queue mapping in the way as it shown in IEEE 802.1Q
mapping example.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I tested ETS support on KSZ9893, so it should work other KSZ989X
variants too, which was till not listed as support.
With this change we now officially not support only ksz8 family of
chips.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
KSZ88X3 switches have different behavior on different ports:
- It seems to be not possible to disable VLAN PCP classification on port
2. It means, as soon as mutliqueue support is enabled, frames with
VLAN tag will get PCP prios. This behavior do not affect Port 1 -
it is possible to disable PCP prios.
- DSCP classification is not working on Port 2.
Since there are still usable configuration combinations, I added some
quirks to make sure user will get appropriate error message if not
possible configuration is chosen.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add DCB support to configure app trust sources and default port priority.
Following commands can be used for testing:
dcb apptrust set dev lan1 order pcp dscp
dcb app replace dev lan1 default-prio 3
Since it is not possible to configure DSCP-Prio mapping per port, this
patch provide only ability to read switch global dscp-prio mapping and
way to enable/disable app trust for DSCP.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
KSZ88X3 switches support up to 4 queues. Rework ksz8795_set_prio_queue()
to support KSZ8795 and KSZ88X3 families of switches.
Per default, configure KSZ88X3 to use one queue, since it need special
handling due to priority related errata. Errata handling is implemented
in a separate patch.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IEEE 802.1q specification provides recommendation and examples which can
be used as good default values for different drivers.
This patch implements mapping examples documented in IEEE 802.1Q-2022 in
Annex I "I.3 Traffic type to traffic class mapping" and IETF DSCP naming
and mapping DSCP to Traffic Type inspired by RFC8325.
This helpers will be used in followup patches for dsa/microchip DCB
implementation.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Most of Microchip KSZ switches use Internal Priority Value associated
with every frame. For example, it is possible to map any VLAN PCP or
DSCP value to IPV and at the end, map IPV to a queue.
Since amount of IPVs is not equal to amount of queues, add this
information and make use of it in some functions.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add DCB support to get/set trust configuration for different packet
priority information sources. Some switch allow to chose different
source of packet priority classification. For example on KSZ switches it
is possible to configure VLAN PCP and/or DSCP sources.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When tmigr_setup_groups() fails the level 0 group allocation, then the
cleanup derefences index -1 of the local stack array.
Prevent this by checking the loop condition first.
Fixes: 7ee988770326 ("timers: Implement the hierarchical pull model")
Signed-off-by: Levi Yun <ppbuk5246@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Link: https://lore.kernel.org/r/20240506041059.86877-1-ppbuk5246@gmail.com
|
|
Use the superblock's UUID to generate the fsid when it's non-null.
Reviewed-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Reviewed-by: Jingbo Xu <jefflexu@linux.alibaba.com>
Signed-off-by: Hongzhen Luo <hongzhen@linux.alibaba.com>
Link: https://lore.kernel.org/r/20240409113022.74720-1-hongzhen@linux.alibaba.com
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
|
