| Age | Commit message (Collapse) | Author |
|---|
|
The STM32MP13x Device Part Number (also named RPN in reference manual)
only uses the first 12 bits in OTP4, all the other bit are reserved and
they can be different of zero; they must be masked in NVMEM result, so
the number of bits must be defined in the nvmem cell description.
Fixes: 1da8779c0029 ("ARM: dts: stm32: add STM32MP13 SoCs support")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Commit 2dc0b46b5ea3 ("libata: sata_down_spd_limit should return if
driver has not recorded sstatus speed") changed the behavior of
sata_down_spd_limit() to return doing nothing if a drive does not report
a current link speed, to avoid reducing the link speed to the lowest 1.5
Gbps speed.
However, the change assumed that a speed was recorded before probing
(e.g. before a suspend/resume) and set in link->sata_spd. This causes
problems with adapters/drives combination failing to establish a link
speed during probe autonegotiation. One example reported of this problem
is an mvebu adapter with a 3Gbps port-multiplier box: autonegotiation
fails, leaving no recorded link speed and no reported current link
speed. Probe retries also fail as no action is taken by sata_set_spd()
after each retry.
Fix this by returning early in sata_down_spd_limit() only if we do have
a recorded link speed, that is, if link->sata_spd is not 0. With this
fix, a failed probe not leading to a recorded link speed is retried at
the lower 1.5 Gbps speed, with the link speed potentially increased
later on the second revalidate of the device if the device reports
that it supports higher link speeds.
Reported-by: Marius Dinu <marius@psihoexpert.ro>
Fixes: 2dc0b46b5ea3 ("libata: sata_down_spd_limit should return if driver has not recorded sstatus speed")
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Tested-by: Marius Dinu <marius@psihoexpert.ro>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
Add a DMI match for the CWI501 version of the Chuwi Vi8 tablet,
pointing to the same chuwi_vi8_data as the existing CWI506 version
DMI match.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230202103413.331459-1-hdegoede@redhat.com
|
|
Commit 41b7a347bf14 ("powerpc: Book3S 64-bit outline-only KASAN
support") added a select of ARCH_WANTS_NO_INSTR, because it also added
some uses of noinstr. However noinstr is always defined, regardless of
ARCH_WANTS_NO_INSTR, so there's no need to select it just for that.
As PeterZ says [1]:
Note that by selecting ARCH_WANTS_NO_INSTR you effectively state to
abide by its rules.
As of now the powerpc code does not abide by those rules, and trips some
new warnings added by Peter in linux-next.
So until the code can be fixed to avoid those warnings, disable
ARCH_WANTS_NO_INSTR.
Note that ARCH_WANTS_NO_INSTR is also used to gate building KCOV and
parts of KCSAN. However none of the noinstr annotations in powerpc were
added for KCOV or KCSAN, instead instrumentation is blocked at the file
level using KCOV_INSTRUMENT_foo.o := n.
[1]: https://lore.kernel.org/linuxppc-dev/Y9t6yoafrO5YqVgM@hirez.programming.kicks-ass.net
Reported-by: Sachin Sant <sachinp@linux.ibm.com>
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This will fix null pointer dereference that was caused by
the driver attempting to resume ports that were not yet
registered.
Fixes: e0dced9c7d47 ("usb: typec: ucsi: Resume in separate work")
Cc: <stable@vger.kernel.org>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216697
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230131141518.78215-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
tx_obj_num_coalesce_irq
If the a new ring layout is set, the max coalesced frames for RX and
TX are re-calculated, too. Add the missing assignment of the newly
calculated TX max coalesced frames.
Fixes: 656fc12ddaf8 ("can: mcp251xfd: add TX IRQ coalescing ethtool support")
Link: https://lore.kernel.org/all/20230130154334.1578518-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The timer for the transmission of isotp PDUs formerly had two functions:
1. send two consecutive frames with a given time gap
2. monitor the timeouts for flow control frames and the echo frames
This led to larger txstate checks and potentially to a problem discovered
by syzbot which enabled the panic_on_warn feature while testing.
The former 'txtimer' function is split into 'txfrtimer' and 'txtimer'
to handle the two above functionalities with separate timer callbacks.
The two simplified timers now run in one-shot mode and make the state
transitions (especially with isotp_rcv_echo) better understandable.
Fixes: 866337865f37 ("can: isotp: fix tx state handling for echo tx processing")
Reported-by: syzbot+5aed6c3aaba661f5b917@syzkaller.appspotmail.com
Cc: stable@vger.kernel.org # >= v6.0
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/all/20230104145701.2422-1-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
When wait_event_interruptible() has been interrupted by a signal the
tx.state value might not be ISOTP_IDLE. Force the state machines
into idle state to inhibit the timer handlers to continue working.
Fixes: 866337865f37 ("can: isotp: fix tx state handling for echo tx processing")
Cc: stable@vger.kernel.org
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/all/20230112192347.1944-1-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
A CAN XL device is always capable to process CAN FD frames. The former
check when sending CAN FD frames relied on the existence of a CAN FD
device and did not check for a CAN XL device that would be correct
too.
With this patch the CAN FD feature is enabled automatically when CAN
XL is switched on - and CAN FD cannot be switch off while CAN XL is
enabled.
This precondition also leads to a clean up and reduction of checks in
the hot path in raw_rcv() and raw_sendmsg(). Some conditions are
reordered to handle simple checks first.
changes since v1: https://lore.kernel.org/all/20230131091012.50553-1-socketcan@hartkopp.net
- fixed typo: devive -> device
changes since v2: https://lore.kernel.org/all/20230131091824.51026-1-socketcan@hartkopp.net/
- reorder checks in if statements to handle simple checks first
Fixes: 626332696d75 ("can: raw: add CAN XL support")
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/all/20230131105613.55228-1-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The conclusion "j1939_session_deactivate() should be called with a
session ref-count of at least 2" is incorrect. In some concurrent
scenarios, j1939_session_deactivate can be called with the session
ref-count less than 2. But there is not any problem because it
will check the session active state before session putting in
j1939_session_deactivate_locked().
Here is the concurrent scenario of the problem reported by syzbot
and my reproduction log.
cpu0 cpu1
j1939_xtp_rx_eoma
j1939_xtp_rx_abort_one
j1939_session_get_by_addr [kref == 2]
j1939_session_get_by_addr [kref == 3]
j1939_session_deactivate [kref == 2]
j1939_session_put [kref == 1]
j1939_session_completed
j1939_session_deactivate
WARN_ON_ONCE(kref < 2)
=====================================================
WARNING: CPU: 1 PID: 21 at net/can/j1939/transport.c:1088 j1939_session_deactivate+0x5f/0x70
CPU: 1 PID: 21 Comm: ksoftirqd/1 Not tainted 5.14.0-rc7+ #32
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1 04/01/2014
RIP: 0010:j1939_session_deactivate+0x5f/0x70
Call Trace:
j1939_session_deactivate_activate_next+0x11/0x28
j1939_xtp_rx_eoma+0x12a/0x180
j1939_tp_recv+0x4a2/0x510
j1939_can_recv+0x226/0x380
can_rcv_filter+0xf8/0x220
can_receive+0x102/0x220
? process_backlog+0xf0/0x2c0
can_rcv+0x53/0xf0
__netif_receive_skb_one_core+0x67/0x90
? process_backlog+0x97/0x2c0
__netif_receive_skb+0x22/0x80
Fixes: 0c71437dd50d ("can: j1939: j1939_session_deactivate(): clarify lifetime of session object")
Reported-by: syzbot+9981a614060dcee6eeca@syzkaller.appspotmail.com
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/all/20210906094200.95868-1-william.xuanziyang@huawei.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Before the commit fc274c1e9973 ("USB: gadget: Add a new bus for gadgets")
gadget driver.bus was unused. For whatever reason, many UDC drivers set
this field explicitly to NULL in udc_start(). With the newly added gadget
bus, doing this will crash the driver during the attach.
The problem was first reported, fixed and tested with OMAP UDC and g_ether.
Other drivers are changed based on code analysis only.
Fixes: fc274c1e9973 ("USB: gadget: Add a new bus for gadgets")
Cc: stable <stable@kernel.org>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20230201220125.GD2415@darkstar.musicnaut.iki.fi
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
netvsc_dma_map() and netvsc_dma_unmap() currently check the cp_partial
flag and adjust the page_count so that pagebuf entries for the RNDIS
portion of the message are skipped when it has already been copied into
a send buffer. But this adjustment has already been made by code in
netvsc_send(). The duplicate adjustment causes some pagebuf entries to
not be mapped. In a normal VM, this doesn't break anything because the
mapping doesn’t change the PFN. But in a Confidential VM,
dma_map_single() does bounce buffering and provides a different PFN.
Failing to do the mapping causes the wrong PFN to be passed to Hyper-V,
and various errors ensue.
Fix this by removing the duplicate adjustment in netvsc_dma_map() and
netvsc_dma_unmap().
Fixes: 846da38de0e8 ("net: netvsc: Add Isolation VM support for netvsc driver")
Cc: stable@vger.kernel.org
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Link: https://lore.kernel.org/r/1675135986-254490-1-git-send-email-mikelley@microsoft.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Exact match feature is only available in CN10K-B.
Unregister exact match devlink entry only for
this silicon variant.
Fixes: 87e4ea29b030 ("octeontx2-af: Debugsfs support for exact match.")
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230131061659.1025137-1-rkannoth@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
clang static analysis reports
drivers/net/ethernet/intel/igc/igc_ptp.c:673:3: warning: The left operand of
'+' is a garbage value [core.UndefinedBinaryOperatorResult]
ktime_add_ns(shhwtstamps.hwtstamp, adjust);
^ ~~~~~~~~~~~~~~~~~~~~
igc_ptp_systim_to_hwtstamp() silently returns without setting the hwtstamp
if the mac type is unknown. This should be treated as an error.
Fixes: 81b055205e8b ("igc: Add support for RX timestamping")
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20230131215437.1528994-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When THP is enabled, 4K pages are collapsed into a single huge
page using the generic pmdp_collapse_flush() which will further
use flush_tlb_range() to shoot-down stale TLB entries. Unfortunately,
the generic pmdp_collapse_flush() only invalidates cached leaf PTEs
using address specific SFENCEs which results in repetitive (or
unpredictable) page faults on RISC-V implementations which cache
non-leaf PTEs.
Provide a RISC-V specific pmdp_collapse_flush() which ensures both
cached leaf and non-leaf PTEs are invalidated by using non-address
specific SFENCEs as recommended by the RISC-V privileged specification.
Fixes: e88b333142e4 ("riscv: mm: add THP support on 64-bit")
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Link: https://lore.kernel.org/r/20230130074815.1694055-1-mchitale@ventanamicro.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
GCC 13 will enable -fasynchronous-unwind-tables by default on riscv. In
the kernel, we don't have any use for unwind tables yet, so disable them.
More importantly, the .eh_frame section brings relocations
(R_RISC_32_PCREL, R_RISCV_SET{6,8,16}, R_RISCV_SUB{6,8,16}) into modules
that we are not prepared to handle.
Signed-off-by: Andreas Schwab <schwab@suse.de>
Link: https://lore.kernel.org/r/mvmzg9xybqu.fsf@suse.de
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
The kernel would panic when probed for an illegal position. eg:
(CONFIG_RISCV_ISA_C=n)
echo 'p:hello kernel_clone+0x16 a0=%a0' >> kprobe_events
echo 1 > events/kprobes/hello/enable
cat trace
Kernel panic - not syncing: stack-protector: Kernel stack
is corrupted in: __do_sys_newfstatat+0xb8/0xb8
CPU: 0 PID: 111 Comm: sh Not tainted
6.2.0-rc1-00027-g2d398fe49a4d #490
Hardware name: riscv-virtio,qemu (DT)
Call Trace:
[<ffffffff80007268>] dump_backtrace+0x38/0x48
[<ffffffff80c5e83c>] show_stack+0x50/0x68
[<ffffffff80c6da28>] dump_stack_lvl+0x60/0x84
[<ffffffff80c6da6c>] dump_stack+0x20/0x30
[<ffffffff80c5ecf4>] panic+0x160/0x374
[<ffffffff80c6db94>] generic_handle_arch_irq+0x0/0xa8
[<ffffffff802deeb0>] sys_newstat+0x0/0x30
[<ffffffff800158c0>] sys_clone+0x20/0x30
[<ffffffff800039e8>] ret_from_syscall+0x0/0x4
---[ end Kernel panic - not syncing: stack-protector:
Kernel stack is corrupted in: __do_sys_newfstatat+0xb8/0xb8 ]---
That is because the kprobe's ebreak instruction broke the kernel's
original code. The user should guarantee the correction of the probe
position, but it couldn't make the kernel panic.
This patch adds arch_check_kprobe in arch_prepare_kprobe to prevent an
illegal position (Such as the middle of an instruction).
Fixes: c22b0bcb1dd0 ("riscv: Add kprobes supported")
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
Signed-off-by: Guo Ren <guoren@kernel.org>
Reviewed-by: Björn Töpel <bjorn@kernel.org>
Link: https://lore.kernel.org/r/20230201040604.3390509-1-guoren@kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
A mutex may sleep, which is not permitted in atomic context.
Avoid a case where this may arise by moving the to
nfp_flower_lag_get_info_from_netdev() in nfp_tun_write_neigh() spinlock.
Fixes: abc210952af7 ("nfp: flower: tunnel neigh support bond offload")
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Yanguo Li <yanguo.li@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230131080313.2076060-1-simon.horman@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
'ip-ip6_gre-fix-gre-tunnels-not-generating-ipv6-link-local-addresses'
Thomas Winter says:
====================
ip/ip6_gre: Fix GRE tunnels not generating IPv6 link local addresses
For our point-to-point GRE tunnels, they have IN6_ADDR_GEN_MODE_NONE
when they are created then we set IN6_ADDR_GEN_MODE_EUI64 when they
come up to generate the IPv6 link local address for the interface.
Recently we found that they were no longer generating IPv6 addresses.
Also, non-point-to-point tunnels were not generating any IPv6 link
local address and instead generating an IPv6 compat address,
breaking IPv6 communication on the tunnel.
These failures were caused by commit e5dd729460ca and this patch set
aims to resolve these issues.
====================
Link: https://lore.kernel.org/r/20230131034646.237671-1-Thomas.Winter@alliedtelesis.co.nz
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We recently found that our non-point-to-point tunnels were not
generating any IPv6 link local address and instead generating an
IPv6 compat address, breaking IPv6 communication on the tunnel.
Previously, addrconf_gre_config always would call addrconf_addr_gen
and generate a EUI64 link local address for the tunnel.
Then commit e5dd729460ca changed the code path so that add_v4_addrs
is called but this only generates a compat IPv6 address for
non-point-to-point tunnels.
I assume the compat address is specifically for SIT tunnels so
have kept that only for SIT - GRE tunnels now always generate link
local addresses.
Fixes: e5dd729460ca ("ip/ip6_gre: use the same logic as SIT interfaces when computing v6LL address")
Signed-off-by: Thomas Winter <Thomas.Winter@alliedtelesis.co.nz>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
For our point-to-point GRE tunnels, they have IN6_ADDR_GEN_MODE_NONE
when they are created then we set IN6_ADDR_GEN_MODE_EUI64 when they
come up to generate the IPv6 link local address for the interface.
Recently we found that they were no longer generating IPv6 addresses.
This issue would also have affected SIT tunnels.
Commit e5dd729460ca changed the code path so that GRE tunnels
generate an IPv6 address based on the tunnel source address.
It also changed the code path so GRE tunnels don't call addrconf_addr_gen
in addrconf_dev_config which is called by addrconf_sysctl_addr_gen_mode
when the IN6_ADDR_GEN_MODE is changed.
This patch aims to fix this issue by moving the code in addrconf_notify
which calls the addr gen for GRE and SIT into a separate function
and calling it in the places that expect the IPv6 address to be
generated.
The previous addrconf_dev_config is renamed to addrconf_eth_config
since it only expected eth type interfaces and follows the
addrconf_gre/sit_config format.
A part of this changes means that the loopback address will be
attempted to be configured when changing addr_gen_mode for lo.
This should not be a problem because the address should exist anyway
and if does already exist then no error is produced.
Fixes: e5dd729460ca ("ip/ip6_gre: use the same logic as SIT interfaces when computing v6LL address")
Signed-off-by: Thomas Winter <Thomas.Winter@alliedtelesis.co.nz>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There could be boards with DCN listed in IP discovery, but no
display hardware actually wired up. In this case the vbios
display table will not be populated. Detect this case and
skip loading DM when we detect it.
v2: Mark DCN as harvested as well so other display checks
elsewhere in the driver are handled properly.
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
These sysfs nodes are tested supported, so enable them.
Signed-off-by: Yiqing Yao <yiqing.yao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
A mistake has been made on some boards with NBIO 4.3.0 where some
NBIO registers aren't properly set by the hardware.
Ensure that they're set during initialization.
Cc: Natikar Basavaraj <Basavaraj.Natikar@amd.com>
Tested-by: Satyanarayana ReddyTVN <Satyanarayana.ReddyTVN@amd.com>
Tested-by: Rutvij Gajjar <Rutvij.Gajjar@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.1.x
|
|
Enable HDP clock gating control for gfx 11.0.3.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
PMFW will handle the features disablement properly for gpu reset case,
driver involvement may cause some unexpected issues.
Cc: stable@vger.kernel.org # 6.1
Signed-off-by: Tim Huang <tim.huang@amd.com>
Reviewed-by: Yifan Zhang <yifan1.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Otherwise we can be out of sync with what's in the hardware, leading
to us rerunning every command that's presently in the ringbuffer.
[How]
Reset software state for the mailboxes in hw_reset callback.
This is already done as part of the mailbox init in hw_init, but we
do need to remember to reset the last cached wptr value as well here.
Reviewed-by: Hansen Dsouza <hansen.dsouza@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
The hwss function does_plane_fit_in_mall not applicable to dcn3.2 asics.
Using it with dcn3.2 can result in undefined behaviour.
[How]
Assign the function pointer to NULL.
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Lower max_downscale_ratio and ARGB888 downscale factor
to prevent cases where underflow may occur on dcn314
[How]
Set max_downscale_ratio to 400 and ARGB downscale factor
to 250 for dcn314
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Daniel Miess <Daniel.Miess@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Brackets missing in the calculation for MIN_DST_Y_NEXT_START
[How]
Add missing brackets for this calculation
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Daniel Miess <Daniel.Miess@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
SQ_WAVE_INST_DW0 isn't present on gfx11 compared to gfx10, so update
wave data type to signify a difference.
Signed-off-by: Graham Sider <Graham.Sider@amd.com>
Reviewed-by: Mukul Joshi <Mukul.Joshi@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.1.x
|
|
We source root cgroup stats from the system-wide stats, see blkcg_print_stat
and blkcg_rstat_flush, so don't update io state for root cgroup.
Fixes blkg leak issue introduced in commit 3b8cc6298724 ("blk-cgroup: Optimize blkcg_rstat_flush()")
which starts to grab blkg's reference when adding iostat_cpu into percpu
blkcg list, but this state won't be consumed by blkcg_rstat_flush() where
the blkg reference is dropped.
Tested-by: Bart van Assche <bvanassche@acm.org>
Reported-by: Bart van Assche <bvanassche@acm.org>
Fixes: 3b8cc6298724 ("blk-cgroup: Optimize blkcg_rstat_flush()")
Cc: Tejun Heo <tj@kernel.org>
Cc: Waiman Long <longman@redhat.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230202021804.278582-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Commit baf1ed24b27d ("powerpc/mm: Remove empty hash__ functions")
removed some empty hash MMU flushing routines, but got a bit overeager
and also removed the call to hash__tlb_flush() from tlb_flush().
In regular use this doesn't lead to any noticable breakage, which is a
little concerning. Presumably there are flushes happening via other
paths such as arch_leave_lazy_mmu_mode(), and/or a bit of luck.
Fix it by reinstating the call to hash__tlb_flush().
Fixes: baf1ed24b27d ("powerpc/mm: Remove empty hash__ functions")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20230131111407.806770-1-mpe@ellerman.id.au
|
|
Wire up the missing ptrace requests PTRACE_GETREGS, PTRACE_SETREGS,
PTRACE_GETFPREGS and PTRACE_SETFPREGS when running 32-bit applications
on 64-bit kernels.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # 4.7+
|
|
Prefer usage of the PRIV_USER constant over the hard-coded value to set
the lowest 2 bits for the userspace privilege.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # 5.16+
|
|
Pull virtio fixes from Michael Tsirkin:
"Just small bugfixes all over the place"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vdpa: ifcvf: Do proper cleanup if IFCVF init fails
vhost-scsi: unbreak any layout for response
tools/virtio: fix the vringh test for virtio ring changes
vhost/net: Clear the pending messages when the backend is removed
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A bit higher volume of changes than wished, but each change is
relatively small and the fix targets are mostly device-specific, so
those should be safe as a late stage merge.
The most significant LoC is about the memalloc helper fix, which is
applied only to Xen PV. The other major parts are ASoC Intel SOF and
AVS fixes that are scattered as various small code changes. The rest
are device-specific fixes and quirks for HD- and USB-audio, FireWire
and ASoC AMD / HDMI"
* tag 'sound-6.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (30 commits)
ALSA: firewire-motu: fix unreleased lock warning in hwdep device
ALSA: memalloc: Workaround for Xen PV
ASoC: cs42l56: fix DT probe
ASoC: codecs: wsa883x: correct playback min/max rates
ALSA: hda/realtek: Add Acer Predator PH315-54
ASoC: amd: yc: Add Xiaomi Redmi Book Pro 15 2022 into DMI table
ALSA: hda: Do not unset preset when cleaning up codec
ASoC: SOF: sof-audio: prepare_widgets: Check swidget for NULL on sink failure
ASoC: hdmi-codec: zero clear HDMI pdata
ASoC: SOF: ipc4-mtrace: prevent underflow in sof_ipc4_priority_mask_dfs_write()
ASoC: Intel: sof_ssp_amp: always set dpcm_capture for amplifiers
ASoC: Intel: sof_nau8825: always set dpcm_capture for amplifiers
ASoC: Intel: sof_cs42l42: always set dpcm_capture for amplifiers
ASoC: Intel: sof_rt5682: always set dpcm_capture for amplifiers
ALSA: hda/via: Avoid potential array out-of-bound in add_secret_dac_path()
ALSA: usb-audio: Add FIXED_RATE quirk for JBL Quantum610 Wireless
ALSA: hda/realtek: fix mute/micmute LEDs, speaker don't work for a HP platform
ASoC: SOF: keep prepare/unprepare widgets in sink path
ASoC: SOF: sof-audio: skip prepare/unprepare if swidget is NULL
ASoC: SOF: sof-audio: unprepare when swidget->use_count > 0
...
|
|
When we parse the ZT signal context we read the entire context from
userspace, including the generic signal context header which was already
read by parse_user_sigframe() and padding bytes that we ignore. Avoid the
possibility of relying on the second read of the data read twice by only
reading the data which we are actually going to use.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20221212-arm64-signal-cleanup-v3-7-4545c94b20ff@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
When we parse the ZA signal context we read the entire context from
userspace, including the generic signal context header which was already
read by parse_user_sigframe() and padding bytes that we ignore. Avoid the
possibility of relying on the second read of the data read twice by only
reading the data which we are actually going to use.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20221212-arm64-signal-cleanup-v3-6-4545c94b20ff@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
When we parse the SVE signal context we read the entire context from
userspace, including the generic signal context header which was already
read by parse_user_sigframe() and padding bytes that we ignore. Avoid the
possibility of relying on the second read of the data read twice by only
reading the data which we are actually going to use.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20221212-arm64-signal-cleanup-v3-5-4545c94b20ff@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
We need to read the sizes of the signal context frames as part of parsing
the overall signal context in parse_user_sigframe(). In the cases where we
defer frame specific parsing to other functions those functions (other
than the recently added TPIDR2 parser) reread the size and validate the
version they read, opening the possibility that the value may change.
Avoid this possibility by passing the size read in parse_user_sigframe()
through user_ctxs and referring to that.
For consistency we move the size check for the TPIDR2 context into the
TPIDR2 parsing function.
Note that for SVE, ZA and ZT contexts we still read the size again but
after this change we no longer use the value, further changes will avoid
the read.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20221212-arm64-signal-cleanup-v3-4-4545c94b20ff@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Instead of taking a pointer to struct user_ctxs like the other two
restore_blah_context() functions the FPSIMD function takes a pointer to the
user struct it should read. Change it to be consistent with the rest, both
for consistency and to prepare for changes which avoid rereading data that
has already been read by the core parsing code.
There should be no functional change from this patch.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20221212-arm64-signal-cleanup-v3-3-4545c94b20ff@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
There is some minimal size validation in parse_user_sigframe() however
all of the individual parsing functions perform frame specific validation
of the sizing information, remove the frame specific size checks in the
core so that there isn't any confusion about what we validate for size.
Since the checks in the SVE and ZA parsing are after we have read the
relevant context and since they won't report an error if the frame is
undersized they are adjusted to check for this before doing anything else.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20221212-arm64-signal-cleanup-v3-2-4545c94b20ff@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
We validate that the magic in the struct fpsimd_context is correct in
restore_fpsimd_context() but this is redundant since parse_user_sigframe()
uses this magic to decide to call the function in the first place. Remove
the extra validation.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20221212-arm64-signal-cleanup-v3-1-4545c94b20ff@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Patches on this branch depend on the branches merged above.
|
|
At present the hwcaps are hard to read and a bit error prone since the
macros used to specify matches require us to write out the register name
multiple times and explicitly specify the width of the field, hopefully
using the correct constant. Now that all the ID registers are generated we
can improve this somewhat by redoing the macros so that we specify the
register, field and minimum value symbolically and use token pasting to
initialise the capability struct with the appropriate values.
We move from specifying like this:
HWCAP_CAP(SYS_ID_AA64PFR1_EL1, ID_AA64PFR1_EL1_BT_SHIFT, 4, FTR_UNSIGNED, ID_AA64PFR1_EL1_BT_IMP, CAP_HWCAP, KERNEL_HWCAP_BTI),
to this:
HWCAP_CAP(ID_AA64PFR1_EL1, BT, IMP, CAP_HWCAP, KERNEL_HWCAP_BTI),
which is shorter due to having less duplicate information and makes it
much harder to make an error like specifying the wrong field width or
an invalid enumeration value since everything must be a constant defined
for the sysreg and names are only typed once.
There should be no functional effect from this change, a check of the
generated .rodata showed no differences.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20221207-arm64-sysreg-helpers-v4-5-25b6b3fb9d18@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Our table of hwcaps sometimes uses the defined constant to specify the
enumeration value they are attempting to match but in some cases an
unadorned number is used. In preparation for using helper macros to to
specify the hwcaps less verbosely replace the magic numbers with their
constants, this will hopefully make the conversion to helper macros
easier to review.
There should be no functional effect from this change, a check of the
generate .rodata showed no differences.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20221207-arm64-sysreg-helpers-v4-4-25b6b3fb9d18@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
In order to allow the simplification of way we declare hwcaps annotate
most of the unsigned fields in the identification registers as such. This
is not a complete annotation, it does cover all the cases where we already
annotate signedness of the field in the hwcaps and some others which I
happened to look at and seemed clear but there will be more and nothing
outside the identification registers was even looked at.
Other fields can be annotated as incrementally as people have the time and
need to do so.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20221207-arm64-sysreg-helpers-v4-3-25b6b3fb9d18@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
We currently annotate a few bitfields as signed in hwcaps, update all of
these to be SignedEnum in the sysreg generation. Further signed bitfields
can be done incrementally, this is the minimum required for the conversion
of the hwcaps to use token pasting to simplify their declaration.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20221207-arm64-sysreg-helpers-v4-2-25b6b3fb9d18@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Many of our enumerations follow a standard scheme where the values can be
treated as signed however there are some where the value must be treated
as signed and others that are simple enumerations where there is no clear
ordering to the values. Provide new field types SignedEnum and
UnsignedEnum which allows the signedness to be specified in the sysreg
definition and emit a REG_FIELD_SIGNED define for these which is a
boolean corresponding to our current FTR_UNSIGNED and FTR_SIGNED macros.
Existing Enums will need to be converted, since these do not have a
define generated anyone wishing to use the sign of one of these will
need to explicitly annotate that field so nothing should start going
wrong by default.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20221207-arm64-sysreg-helpers-v4-1-25b6b3fb9d18@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
