| Age | Commit message (Collapse) | Author |
|---|
|
If we have a state already and disconnect/reconnect the display, the
SCDC messages won't be sent again since we didn't go through a disable /
enable cycle.
In order to fix this, let's call the vc4_hdmi_enable_scrambling function
in the detect callback if there is a mode and it needs the scrambler to
be enabled.
Fixes: c85695a2016e ("drm/vc4: hdmi: Enable the scrambler")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20211025152903.1088803-10-maxime@cerno.tech
|
|
Now that we have the infrastructure in place, we can raise the maximum
pixel rate we can reach for HDMI0 on the BCM2711.
HDMI1 is left untouched since its pixelvalve has a smaller FIFO and
would need a clock faster than what we can provide to support the same
modes.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20211025152903.1088803-9-maxime@cerno.tech
|
|
The load tracker was initially designed to report and warn about a load
too high for the HVS. To do so, it computes for each plane the impact
it's going to have on the HVS, and will warn (if it's enabled) if we go
over what the hardware can process.
While the limits being used are a bit irrelevant to the BCM2711, the
algorithm to compute the HVS load will be one component used in order to
compute the core clock rate on the BCM2711.
Let's remove the hooks to prevent the load tracker to do its
computation, but since we don't have the same limits, don't check them
against them, and prevent the debugfs file to enable it from being
created.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20211025152903.1088803-8-maxime@cerno.tech
|
|
The encoder retrieval code has been a source of bugs and glitches in the
past and the crtc <-> encoder association been wrong in a number of
different ways.
Add some logging to quickly spot issues if they occur.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20211025152903.1088803-7-maxime@cerno.tech
|
|
It turns out the encoder retrieval code, in addition to being
unnecessarily complicated, has a bug when only the planes and crtcs are
affected by a given atomic commit.
Indeed, in such a case, either drm_atomic_get_old_connector_state or
drm_atomic_get_new_connector_state will return NULL and thus our encoder
retrieval code will not match on anything.
We can however simplify the code by using drm_for_each_encoder_mask, the
drm_crtc_state storing the encoders a given CRTC is connected to
directly and without relying on any other state.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20211025152903.1088803-6-maxime@cerno.tech
|
|
vc4_crtc_config_pv() retrieves the encoder again, even though its only
caller, vc4_crtc_atomic_enable(), already did.
Pass the encoder pointer as an argument instead of going through all the
connectors to retrieve it again.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20211025152903.1088803-5-maxime@cerno.tech
|
|
We'll need that function in vc4_kms to compute the core clock rate
requirements.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20211025152903.1088803-4-maxime@cerno.tech
|
|
Prior to commit 6800234ceee0 ("drm/vc4: hdmi: Convert to gpiod"), in the
detect hook, if we had an HPD GPIO we would only rely on it and return
whatever state it was in.
However, that commit changed that by mistake to only consider the case
where we have a GPIO and it returns a logical high, and would fall back
to the other methods otherwise.
Since we can read the EDIDs when the HPD signal is low on some displays,
we changed the detection status from disconnected to connected, and we
would ignore an HPD pulse.
Fixes: 6800234ceee0 ("drm/vc4: hdmi: Convert to gpiod")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20211025152903.1088803-3-maxime@cerno.tech
|
|
Commit 9d44abbbb8d5 ("drm/vc4: Fall back to using an EDID probe in the
absence of a GPIO.") added some code to read the EDID through DDC in the
HDMI driver detect hook since the Pi3 had no HPD GPIO back then.
However, commit b1b8f45b3130 ("ARM: dts: bcm2837: Add missing GPIOs of
Expander") changed that a couple of years later.
This causes an issue though since some TV (like the LG 55C8) when it
comes out of standy will deassert the HPD line, but the EDID will
remain readable.
It causes an issues nn platforms without an HPD GPIO, like the Pi4,
where the DDC probing will be our primary mean to detect a display, and
thus we will never detect the HPD pulse. This was fine before since the
pulse was small enough that we would never detect it, and we also didn't
have anything (like the scrambler) that needed to be set up in the
display.
However, now that we have both, the display during the HPD pulse will
clear its scrambler status, and since we won't detect the
disconnect/reconnect cycle we will never enable the scrambler back.
As our main reason for that DDC probing is gone, let's just remove it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20211025152903.1088803-2-maxime@cerno.tech
|
|
Don't touch the exclusive fence manually here, but rather use the
general dma_resv function. We did that for better hw reset handling but
this doesn't necessary work correctly.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deuche <alexander.deucher@amd.com>
Acked-by: Nirmoy Das <nirmoy.das@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211028132630.2330-6-christian.koenig@amd.com
|
|
This makes sure we don't hit the
BUG_ON(dmabuf->cb_in.active || dmabuf->cb_out.active);
in dma_buf_release, which could be triggered by user space closing the
dma-buf file description while there are outstanding fence callbacks
from dma_buf_poll.
Cc: stable@vger.kernel.org
Signed-off-by: Michel Dänzer <mdaenzer@redhat.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723075857.4065-1-michel@daenzer.net
Signed-off-by: Christian König <christian.koenig@amd.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The usual collection of clk driver updates and new driver additions.
In terms of lines it's mainly Qualcomm and Mediatek code, supporting
various SoCs and their multitude of clk controllers.
New Drivers:
- GCC and RPMcc support for Qualcomm QCM2290 SoCs
- GCC support for Qualcomm MSM8994/MSM8992 SoCs
- LPASSCC and CAMCC support for Qualcomm SC7280 SoCs
- Support for Mediatek MT8195 SoCs
- Initial clock driver for the Exynos850 SoC
- Add i.MX8ULP clock driver and related bindings
Updates:
- Clock power management for new SAMA7G5 SoC
- Updates to the master clock driver and sam9x60-pll to be able to
use cpufreq-dt driver and avoid overclocking of CPU and MCK0
domains while changing the frequency via DVFS
- Use ARRAY_SIZE in qcom clk drivers
- Remove some impractical fallback parent names in qcom clk drivers
- Make Mediatek clk drivers tristate
- Refactoring of the CPU clock code and conversion of Samsung
Exynos5433 CPU clock driver to the platform driver
- A few conversions to devm_platform_ioremap_resource()
- Updates of the Samsung Kconfig help text
- Update video path realted clocks for Amlogic meson8
- Add SPI Multi I/O Bus and SDHI clocks and resets on Renesas RZ/G2L
- Add SPI Multi I/O Bus (RPC) clocks on Renesas R-Car V3U
- Add MediaLB clocks on Renesas R-Car H3, M3-W/W+, and M3-N
- Remove unused helpers from i.MX specific clock header
- Rework all i.MX clk based helpers to use clk_hw based ones
- Rework i.MX gate/mux/divider wrappers
- Rework imx_clk_hw_composite and imx_clk_hw_pll14xx wrappers
- Update i.MX pllv4 and composite clocks to support i.MX8ULP
- Disable i.MX7ULP composite clock during initialization
- Add CLK_SET_RATE_NO_REPARENT flag to the i.MX7ULP composite
- Disable the i.MX pfd when set pfdv2 clock rate
- Add support for i.MX8ULP in pfdv2
- Add the pcc reset controller support on i.MX8ULP
- Fix the build break when clk-imx8ulp is built as module
- Move csi_sel mux to correct base register in i.MX6UL clock drivr
- Fix csi clk gate register in i.MX6UL clock driver
- Fix build bug making CLK_IMX8ULP select MXC_CLK
- Add TPU (PWM), and Z (Cortex-A76) clocks on Renesas R-Car V3U
- Add Ethernet clocks on Renesas RZ/G2L
- Move Rockchip to use module_platform_probe
- Enable usage of Coresight related clocks on Rockchip rk3399"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (170 commits)
clk: use clk_core_get_rate_recalc() in clk_rate_get()
clk: at91: sama7g5: set low limit for mck0 at 32KHz
clk: at91: sama7g5: remove prescaler part of master clock
clk: at91: clk-master: add notifier for divider
clk: at91: clk-sam9x60-pll: add notifier for div part of PLL
clk: at91: clk-master: fix prescaler logic
clk: at91: clk-master: mask mckr against layout->mask
clk: at91: clk-master: check if div or pres is zero
clk: at91: sam9x60-pll: use DIV_ROUND_CLOSEST_ULL
clk: at91: pmc: add sama7g5 to the list of available pmcs
clk: at91: clk-master: improve readability by using local variables
clk: at91: clk-master: add register definition for sama7g5's master clock
clk: at91: sama7g5: add securam's peripheral clock
clk: at91: pmc: execute suspend/resume only for backup mode
clk: at91: re-factor clocks suspend/resume
clk: ux500: Add driver for the reset portions of PRCC
dt-bindings: clock: u8500: Rewrite in YAML and extend
clk: composite: Use rate_ops.determine_rate when also a mux is available
clk: samsung: describe drivers in Kconfig
clk: samsung: exynos5433: update apollo and atlas clock probing
...
|
|
Move the soc revision parsing to the initial probe, saving the driver
from parsing the register multiple times.
Use this variable to select the correct divisor table for the AHB clock.
Before this fix the A2 would have used the A0 table.
Fixes: 2d491066ccd4 ("clk: ast2600: Fix AHB clock divider for A1")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210922235449.213631-1-joel@jms.id.au
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Need to make sure the command size is valid before copying the command from
user space.
Link: https://lore.kernel.org/r/20211103170659.22151-1-tadeusz.struk@linaro.org
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: James E.J. Bottomley <jejb@linux.ibm.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: <linux-scsi@vger.kernel.org>
Cc: <linux-kernel@vger.kernel.org>
Cc: <stable@vger.kernel.org> # 5.15, 5.14, 5.10
Signed-off-by: Tadeusz Struk <tadeusz.struk@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The spec recommends that for transfer length larger than the max-single-cmd
attribute (bMAX_DATA_SIZE_FOR_HPB_SINGLE_CMD) it is possible to couple
pre-requests with the HPB-READ command. Being a recommendation, using
pre-requests can be perceived merely as a means of optimization. A common
practice was to send pre-requests for chunks within some interval, and
leave the READ10 untouched if larger.
Now that the pre-request flows have been removed, all the commands are
single commands. Properly handle this attribute and do not send HPB-READ
for transfer lengths larger than max-single-cmd.
[mkp: resolve conflict]
Fixes: 09d9e4d04187 ("scsi: ufs: ufshpb: Remove HPB2.0 flows")
Link: https://lore.kernel.org/r/20211031123654.17719-1-avri.altman@wdc.com
Reviewed-by: Daejun Park <daejun7.park@samsung.com>
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The partial UFS revert in 5.15 is needed for some additional fixes in
the 5.16 SCSI tree. Merge the fixes branch.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The changes to issue the abort from the scmd->abort_work instead of the EH
thread introduced a problem if eh_deadline is used. If aborting the
command(s) is successful, and there are never any scmds added to the
shost->eh_cmd_q, there is no code path which will reset the ->last_reset
value back to zero.
The effect of this is that after a successful abort with no EH thread
activity, a subsequent timeout, perhaps a long time later, might
immediately be considered past a user-set eh_deadline time, and the host
will be reset with no attempt at recovery.
Fix this by resetting ->last_reset back to zero in scmd_eh_abort_handler()
if it is determined that the EH thread will not run to do this.
Thanks to Gopinath Marappan for investigating this problem.
Link: https://lore.kernel.org/r/20211029194311.17504-2-emilne@redhat.com
Fixes: e494f6a72839 ("[SCSI] improved eh timeout handler")
Cc: stable@vger.kernel.org
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When the value of error is printed, it will always be 0. We should print
the correct error code when scsi_bsg_register_queue() fails.
Link: https://lore.kernel.org/r/20211022010201.426746-1-liu.yun@linux.dev
Fixes: ead09dd3aed5 ("scsi: bsg: Simplify device registration")
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Christoph Hellwig <hch@lst.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jackie Liu <liuyun01@kylinos.cn>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
During commit 6594988fd625 ("clk: composite: Use rate_ops.determine_rate
when also a mux is available") setting req->best_parent_hw got lost,
so best_parent_hw stays NULL during switch to the same parent. This
results in the (debug) message:
clk_calc_new_rates: lcdif_pixel not gated but wants to reparent
and the following rate change is dropped.
Fixes: 6594988fd625 ("clk: composite: Use rate_ops.determine_rate when also a mux is available")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20211103122441.3208576-1-alexander.stein@ew.tq-group.com
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM defconfig updates from Arnd Bergmann:
"These are the usual changes to enable newly added driver by default,
and to do some housekeeping around changing Kconfig symbols"
* tag 'defconfig-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (33 commits)
arm64: defconfig: Enable Qualcomm LMH driver
arm64: defconfig: Enable Qualcomm prima/pronto drivers
arm64: defconfig: Enable Sleep stats driver
arm64: defconfig: Visconti: Enable PCIe host controller
ARM: configs: aspeed: Remove unused USB gadget devices
ARM: config: aspeed: Enable Network Block Device
ARM: configs: aspeed: Enable pstore and lockup detectors
ARM: configs: aspeed: Enable commonly used drivers
ARM: configs: aspeed: Disable IPV6 SIT device
ARM: imx_v6_v7_defconfig: Enable HID I2C
arm64: defconfig: Enable QTI SC7280 pinctrl, gcc and interconnect
arm64: defconfig: Disable firmware sysfs fallback
ARM: mvebu_v7_defconfig: rebuild default configuration
ARM: mvebu_v7_defconfig: enable mtd physmap
arm64: defconfig: Enable few Tegra210 based AHUB drivers
arm64: defconfig: drop obsolete ARCH_* configs
ARM: imx_v6_v7_defconfig: enable bpf syscall and cgroup bpf
ARM: imx_v6_v7_defconfig: build imx sdma driver as module
ARM: imx_v6_v7_defconfig: rebuild default configuration
ARM: imx_v6_v7_defconfig: change snd soc tlv320aic3x to i2c variant
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"These are all the driver updates for SoC specific drivers. There are a
couple of subsystems with individual maintainers picking up their
patches here:
- The reset controller subsystem add support for a few new SoC
variants to existing drivers, along with other minor improvements
- The OP-TEE subsystem gets a driver for the ARM FF-A transport
- The memory controller subsystem has improvements for Tegra,
Mediatek, Renesas, Freescale and Broadcom specific drivers.
- The tegra cpuidle driver changes get merged through this tree this
time. There are only minor changes, but they depend on other tegra
driver updates here.
- The ep93xx platform finally moves to using the drivers/clk/
subsystem, moving the code out of arch/arm in the process. This
depends on a small sound driver change that is included here as
well.
- There are some minor updates for Qualcomm and Tegra specific
firmware drivers.
The other driver updates are mainly for drivers/soc, which contains a
mixture of vendor specific drivers that don't really fit elsewhere:
- Mediatek drivers gain more support for MT8192, with new support for
hw-mutex and mmsys routing, plus support for reset lines in the
mmsys driver.
- Qualcomm gains a new "sleep stats" driver, and support for the
"Generic Packet Router" in the APR driver.
- There is a new user interface for routing the UARTS on ASpeed BMCs,
something that apparently nobody else has needed so far.
- More drivers can now be built as loadable modules, in particular
for Broadcom and Samsung platforms.
- Lots of improvements to the TI sysc driver for better
suspend/resume support"
Finally, there are lots of minor cleanups and new device IDs for
amlogic, renesas, tegra, qualcomm, mediateka, samsung, imx,
layerscape, allwinner, broadcom, and omap"
* tag 'drivers-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (179 commits)
optee: Fix spelling mistake "reclain" -> "reclaim"
Revert "firmware: qcom: scm: Add support for MC boot address API"
qcom: spm: allow compile-testing
firmware: arm_ffa: Remove unused 'compat_version' variable
soc: samsung: exynos-chipid: add exynosautov9 SoC support
firmware: qcom: scm: Don't break compile test on non-ARM platforms
soc: qcom: smp2p: Add of_node_put() before goto
soc: qcom: apr: Add of_node_put() before return
soc: qcom: qcom_stats: Fix client votes offset
soc: qcom: rpmhpd: fix sm8350_mxc's peer domain
dt-bindings: arm: cpus: Document qcom,msm8916-smp enable-method
ARM: qcom: Add qcom,msm8916-smp enable-method identical to MSM8226
firmware: qcom: scm: Add support for MC boot address API
soc: qcom: spm: Add 8916 SPM register data
dt-bindings: soc: qcom: spm: Document qcom,msm8916-saw2-v3.0-cpu
soc: qcom: socinfo: Add PM8150C and SMB2351 models
firmware: qcom_scm: Fix error retval in __qcom_scm_is_call_available()
soc: aspeed: Add UART routing support
soc: fsl: dpio: rename the enqueue descriptor variable
soc: fsl: dpio: use an explicit NULL instead of 0
...
|
|
Pull ARM SoC DT updates from Arnd Bergmann:
"This is a rather large update for the ARM devicetree files, after a
few quieter releases, with 775 total commits and 47 branches pulled
into this one.
There are 5 new SoC types plus some minor variations, and a total of
60 new machines, so I'm limiting the summary to the main noteworthy
items:
- Apple M1 gain support for PCI and pinctrl, getting a bit closer to
a usable system out of the box.
- Qualcomm gains support for Snapdragon 690 (aka SM6350) as well as
SM7225, 11 new smartphones, and three additional Chromebooks, and
improvements all over the place.
- Samsung gains support for ExynosAutov9, an automotive version of
their smartphone SoC, but otherwise no major changes.
- Microchip adds the SAMA5D29 SoC in the SAMA5 family, and a number
of improvements for the recently added SAMA7 family. The LAN966 SoC
that was added in the platform code does not have dts files yet.
Two board files are added for the older at91sam9g20 SoC
- Aspeed supports two additional server boards using their AST2600 as
BMC, and improves support for qemu models
- Rockchip RK3566/RK3688 gets added, along with six new development
boards using RK3328/RK3399/RK3566, and one Chromebook tablet.
- Two NAS boxes are added using the ARMv4 based Gemini platform
- One new board is added to the Intel Arria SoC FPGA family
- Marvell adds one network switch based on Armada 381 and the new
MOCHAbin 7040 development board
- NXP adds support for the S32G2 automotive SoC, two imx6 based ebook
readers, and three additional development boards, which is notably
less than their usual additions, but they also gain improvements to
their many existing boards
- STmicroelectronics adds their stm32mp13 SoC family along with a
reference board
- Renesas adds new versions of their R-Car Gen3 SoCs and many updates
for their older generations
- Broadcom adds support for a number of Cisco Meraki wireless
controllers, along with two new boards and other updates for
BCM53xx/BCM47xx networking SoCs and the Raspberry Pi boards
- Mediatek improves support for the MT81xx SoCs used in Chromebooks
as well as the MT76xx networking SoCs
- NVIDIA adds a number of cleanups and additional support for more
hardware on the already supported machines
- TI K3 adds support for three new boards along with cleanups
- Toshiba adds one board for the Visconti family
- Xilinx adds five new ZynqMP based machines
- Amlogic support is added for the Radxa Zero and two Jethub home
automation controllers, along with changes to other machines
- Rob Herring continues his work on fixing dtc warnings all over the
tree.
- Minor updates for TI OMAP, Mstar, Allwinner/sunxi, Hisilicon,
Ux500, Unisoc"
* tag 'dt-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (720 commits)
arm64: dts: apple: j274: Expose PCI node for the Ethernet MAC address
arm64: dts: apple: t8103: Add root port interrupt routing
arm64: dts: apple: t8103: Add PCIe DARTs
arm64: apple: Add PCIe node
arm64: apple: Add pinctrl nodes
ARM: dts: arm: Update ICST clock nodes 'reg' and node names
ARM: dts: arm: Update register-bit-led nodes 'reg' and node names
arm64: dts: exynos: add chipid node for exynosautov9 SoC
ARM: dts: qcom: fix typo in IPQ8064 thermal-sensor node
Revert "arm64: dts: qcom: msm8916-asus-z00l: Add sensors"
arm64: dts: qcom: ipq6018: Remove unused 'iface_clk' property from dma-controller node
arm64: dts: qcom: ipq6018: Remove unused 'qcom,config-pipe-trust-reg' property
arm64: dts: qcom: sm8350: Add CPU topology and idle-states
arm64: dts: qcom: Drop unneeded extra device-specific includes
arm64: dts: qcom: msm8916: Drop standalone smem node
arm64: dts: qcom: Fix node name of rpm-msg-ram device nodes
arm64: dts: qcom: msm8916-asus-z00l: Add sensors
arm64: dts: qcom: msm8916-asus-z00l: Add SDCard
arm64: dts: qcom: msm8916-asus-z00l: Add touchscreen
arm64: dts: qcom: sdm845-oneplus: remove devinfo-size from ramoops node
...
|
|
Pull ARM SoC updates from Arnd Bergmann:
"The SoC updates this time are mainly removing obsolete code from the
OMAP2 platform, another step in the eternal cleanup of that platform.
There are two new SoCs getting added: STMicroelectronics stm32mp13 and
Microchip lan966. Both fit into existing platforms and require minimal
changes here.
A couple of MAINTAINER file updates relate to those changes, and
update some file paths"
* tag 'soc-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (28 commits)
MAINTAINERS: Update BCM7XXX entry with additional patterns
MAINTAINERS: add pinctrl-apple-gpio to ARM/APPLE MACHINE
MAINTAINERS: Add pasemi i2c to ARM/APPLE MACHINE
ARM: SPEAr: Update MAINTAINERS entries
ARM: OMAP2+: Drop unused CM defines for am3
ARM: OMAP2+: Drop unused CM and SCRM defines for omap4
ARM: OMAP2+: Drop unused CM and SCRM defines for omap5
ARM: OMAP2+: Drop unused CM defines for dra7
ARM: OMAP2+: Drop unused PRM defines for am3
ARM: OMAP2+: Drop unused PRM defines for am4
ARM: OMAP2+: Drop unused PRM defines for omap4
ARM: OMAP2+: Drop unused PRM defines for omap5
ARM: OMAP2+: Drop unused PRM defines for dra7
ARM: OMAP2+: Fix comment typo
ARM: OMAP2+: Fix typo in some comments
ARM: at91: add basic support for new SoC family lan966
dt-bindings: arm: at91: Document lan966 pcb8291 and pcb8290 boards
ARM: at91: Documentation: add lan966 family
ARM: at91: Documentation: add sama7g5 family
MAINTAINERS: add an entry for NXP S32G boards
...
|
|
The code which constructs the modules for each engine present on the GPU
passes -1 for 'instance' on non-instanced engines, which affects how the
name for a sub-device is generated. This is then stored as 'instance 0'
in nvkm_subdev.inst, so code can potentially be shared with earlier GPUs
that only had a single instance of an engine.
However, GF100's CE constructor uses this value to calculate the address
of its falcon before it's translated, resulting in CE0 getting the wrong
address.
This slightly modifies the approach, always passing a valid instance for
engines that *can* have multiple copies, and having the code for earlier
GPUs explicitly ask for non-instanced name generation.
Bug: https://gitlab.freedesktop.org/drm/nouveau/-/issues/91
Fixes: 50551b15c760 ("drm/nouveau/ce: switch to instanced constructor")
Cc: <stable@vger.kernel.org> # v5.12+
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Karol Herbst <kherbst@redhat.com>
Tested-by: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Karol Herbst <kherbst@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211103011057.15344-1-skeggsb@gmail.com
|
|
It might look better if duplicated 'Returns:' comment is removed.
Signed-off-by: Austin Kim <austindh.kim@gmail.com>
Signed-off-by: John Johansen <john.johansen@canonical.com>
|
|
Use the common function directly.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: John Johansen <john.johansen@canonical.com>
|
|
Make use of the struct_size() helper instead of an open-coded version,
in order to avoid any potential type mistakes or integer overflows that,
in the worse scenario, could lead to heap overflows.
Link: https://github.com/KSPP/linux/issues/160
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: John Johansen <john.johansen@canonical.com>
|
|
Pull virtio updates from Michael Tsirkin:
"vhost and virtio fixes and features:
- Hardening work by Jason
- vdpa driver for Alibaba ENI
- Performance tweaks for virtio blk
- virtio rng rework using an internal buffer
- mac/mtu programming for mlx5 vdpa
- Misc fixes, cleanups"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (45 commits)
vdpa/mlx5: Forward only packets with allowed MAC address
vdpa/mlx5: Support configuration of MAC
vdpa/mlx5: Fix clearing of VIRTIO_NET_F_MAC feature bit
vdpa_sim_net: Enable user to set mac address and mtu
vdpa: Enable user to set mac and mtu of vdpa device
vdpa: Use kernel coding style for structure comments
vdpa: Introduce query of device config layout
vdpa: Introduce and use vdpa device get, set config helpers
virtio-scsi: don't let virtio core to validate used buffer length
virtio-blk: don't let virtio core to validate used length
virtio-net: don't let virtio core to validate used length
virtio_ring: validate used buffer length
virtio_blk: correct types for status handling
virtio_blk: allow 0 as num_request_queues
i2c: virtio: Add support for zero-length requests
virtio-blk: fixup coccinelle warnings
virtio_ring: fix typos in vring_desc_extra
virtio-pci: harden INTX interrupts
virtio_pci: harden MSI-X interrupts
virtio_config: introduce a new .enable_cbs method
...
|
|
tl;dr: AMX state is ~8k. Signal frames can have space for this
~8k and each signal entry writes out all 8k even if it is zeros.
Skip writing zeros for AMX to speed up signal delivery by about
4% overall when AMX is in its init state.
This is a user-visible change to the sigframe ABI.
== Hardware XSAVE Background ==
XSAVE state components may be tracked by the processor as being
in their initial configuration. Software can detect which
features are in this configuration by looking at the XSTATE_BV
field in an XSAVE buffer or with the XGETBV(1) instruction.
Both the XSAVE and XSAVEOPT instructions enumerate features s
being in the initial configuration via the XSTATE_BV field in the
XSAVE header, However, XSAVEOPT declines to actually write
features in their initial configuration to the buffer. XSAVE
writes the feature unconditionally, regardless of whether it is
in the initial configuration or not.
Basically, XSAVE users never need to inspect XSTATE_BV to
determine if the feature has been written to the buffer.
XSAVEOPT users *do* need to inspect XSTATE_BV. They might also
need to clear out the buffer if they want to make an isolated
change to the state, like modifying one register.
== Software Signal / XSAVE Background ==
Signal frames have historically been written with XSAVE itself.
Each state is written in its entirety, regardless of being in its
initial configuration.
In other words, the signal frame ABI uses the XSAVE behavior, not
the XSAVEOPT behavior.
== Problem ==
This means that any application which has acquired permission to
use AMX via ARCH_REQ_XCOMP_PERM will write 8k of state to the
signal frame. This 8k write will occur even when AMX was in its
initial configuration and software *knows* this because of
XSTATE_BV.
This problem also exists to a lesser degree with AVX-512 and its
2k of state. However, AVX-512 use does not require
ARCH_REQ_XCOMP_PERM and is more likely to have existing users
which would be impacted by any change in behavior.
== Solution ==
Stop writing out AMX xfeatures which are in their initial state
to the signal frame. This effectively makes the signal frame
XSAVE buffer look as if it were written with a combination of
XSAVEOPT and XSAVE behavior. Userspace which handles XSAVEOPT-
style buffers should be able to handle this naturally.
For now, include only the AMX xfeatures: XTILE and XTILEDATA in
this new behavior. These require new ABI to use anyway, which
makes their users very unlikely to be broken. This XSAVEOPT-like
behavior should be expected for all future dynamic xfeatures. It
may also be extended to legacy features like AVX-512 in the
future.
Only attempt this optimization on systems with dynamic features.
Disable dynamic feature support (XFD) if XGETBV1 is unavailable
by adding a CPUID dependency.
This has been measured to reduce the *overall* cycle cost of
signal delivery by about 4%.
Fixes: 2308ee57d93d ("x86/fpu/amx: Enable the AMX feature in 64-bit mode")
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: "Chang S. Bae" <chang.seok.bae@intel.com>
Link: https://lore.kernel.org/r/20211102224750.FA412E26@davehans-spike.ostc.intel.com
|
|
When cdns_plat_pcie_probe() succeeds, return success instead of falling
into the error handling code.
Fixes: bd22885aa188 ("PCI: cadence: Refactor driver to use as a core library")
Link: https://lore.kernel.org/r/DM6PR19MB40271B93057D949310F0B0EDA0BF9@DM6PR19MB4027.namprd19.prod.outlook.com
Signed-off-by: Xuliang Zhang <xlzhanga@ambarella.com>
Signed-off-by: Li Chen <lchen@ambarella.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
|
|
Pull VFIO updates from Alex Williamson:
- Cleanup vfio iommu_group creation (Christoph Hellwig)
- Add individual device reset for vfio/fsl-mc (Diana Craciun)
- IGD OpRegion 2.0+ support (Colin Xu)
- Use modern cdev lifecycle for vfio_group (Jason Gunthorpe)
- Use new mdev API in vfio_ccw (Jason Gunthorpe)
* tag 'vfio-v5.16-rc1' of git://github.com/awilliam/linux-vfio: (27 commits)
vfio/ccw: Convert to use vfio_register_emulated_iommu_dev()
vfio/ccw: Pass vfio_ccw_private not mdev_device to various functions
vfio/ccw: Use functions for alloc/free of the vfio_ccw_private
vfio/ccw: Remove unneeded GFP_DMA
vfio: Use cdev_device_add() instead of device_create()
vfio: Use a refcount_t instead of a kref in the vfio_group
vfio: Don't leak a group reference if the group already exists
vfio: Do not open code the group list search in vfio_create_group()
vfio: Delete vfio_get/put_group from vfio_iommu_group_notifier()
vfio/pci: Add OpRegion 2.0+ Extended VBT support.
vfio/iommu_type1: remove IS_IOMMU_CAP_DOMAIN_IN_CONTAINER
vfio/iommu_type1: remove the "external" domain
vfio/iommu_type1: initialize pgsize_bitmap in ->open
vfio/spapr_tce: reject mediated devices
vfio: clean up the check for mediated device in vfio_iommu_type1
vfio: remove the unused mdev iommu hook
vfio: move the vfio_iommu_driver_ops interface out of <linux/vfio.h>
vfio: remove unused method from vfio_iommu_driver_ops
vfio: simplify iommu group allocation for mediated devices
vfio: remove the iommudata hack for noiommu groups
...
|
|
del_gendisk() should not called if the disk has not been added. Fix this.
Fixes: 41cd8b70c37a ("libnvdimm, btt: add support for blk integrity")
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Link: https://lore.kernel.org/r/20211103165843.1402142-1-mcgrof@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull per signal_struct coredumps from Eric Biederman:
"Current coredumps are mixed up with the exit code, the signal handling
code, and the ptrace code making coredumps much more complicated than
necessary and difficult to follow.
This series of changes starts with ptrace_stop and cleans it up,
making it easier to follow what is happening in ptrace_stop. Then
cleans up the exec interactions with coredumps. Then cleans up the
coredump interactions with exit. Finally the coredump interactions
with the signal handling code is cleaned up.
The first and last changes are bug fixes for minor bugs.
I believe the fact that vfork followed by execve can kill the process
the called vfork if exec fails is sufficient justification to change
the userspace visible behavior.
In previous discussions some of these changes were organized
differently and individually appeared to make the code base worse. As
currently written I believe they all stand on their own as cleanups
and bug fixes.
Which means that even if the worst should happen and the last change
needs to be reverted for some unimaginable reason, the code base will
still be improved.
If the worst does not happen there are a more cleanups that can be
made. Signals that generate coredumps can easily become eligible for
short circuit delivery in complete_signal. The entire rendezvous for
generating a coredump can move into get_signal. The function
force_sig_info_to_task be written in a way that does not modify the
signal handling state of the target task (because coredumps are
eligible for short circuit delivery). Many of these future cleanups
can be done another way but nothing so cleanly as if coredumps become
per signal_struct"
* 'per_signal_struct_coredumps-for-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
coredump: Limit coredumps to a single thread group
coredump: Don't perform any cleanups before dumping core
exit: Factor coredump_exit_mm out of exit_mm
exec: Check for a pending fatal signal instead of core_state
ptrace: Remove the unnecessary arguments from arch_ptrace_stop
signal: Remove the bogus sigkill_pending in ptrace_stop
|
|
As Andy pointed out that there are races between
force_sig_info_to_task and sigaction[1] when force_sig_info_task. As
Kees discovered[2] ptrace is also able to change these signals.
In the case of seeccomp killing a process with a signal it is a
security violation to allow the signal to be caught or manipulated.
Solve this problem by introducing a new flag SA_IMMUTABLE that
prevents sigaction and ptrace from modifying these forced signals.
This flag is carefully made kernel internal so that no new ABI is
introduced.
Longer term I think this can be solved by guaranteeing short circuit
delivery of signals in this case. Unfortunately reliable and
guaranteed short circuit delivery of these signals is still a ways off
from being implemented, tested, and merged. So I have implemented a much
simpler alternative for now.
[1] https://lkml.kernel.org/r/b5d52d25-7bde-4030-a7b1-7c6f8ab90660@www.fastmail.com
[2] https://lkml.kernel.org/r/202110281136.5CE65399A7@keescook
Cc: stable@vger.kernel.org
Fixes: 307d522f5eb8 ("signal/seccomp: Refactor seccomp signal and coredump generation")
Tested-by: Andrea Righi <andrea.righi@canonical.com>
Tested-by: Kees Cook <keescook@chromium.org>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
|
|
If an error occurs after a successful cdns_pcie_init_phy() call, it must be
undone by a cdns_pcie_disable_phy() call, as already done above and below.
Update the goto to branch at the correct place of the error handling path.
Link: https://lore.kernel.org/r/db477b0cb444891a17c4bb424467667dc30d0bab.1624794264.git.christophe.jaillet@wanadoo.fr
Fixes: 49e0efdce791 ("PCI: j721e: Add support to provide refclk to PCIe connector")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
|
|
When building m68k:allmodconfig, recent versions of gcc generate the
following error if the length of UTS_RELEASE is less than 8 bytes.
In function 'memcpy_and_pad',
inlined from 'nvmet_execute_disc_identify' at
drivers/nvme/target/discovery.c:268:2: arch/m68k/include/asm/string.h:72:25: error:
'__builtin_memcpy' reading 8 bytes from a region of size 7
Discussions around the problem suggest that this only happens if an
architecture does not provide strlen(), if -ffreestanding is provided as
compiler option, and if CONFIG_FORTIFY_SOURCE=n. All of this is the case
for m68k. The exact reasons are unknown, but seem to be related to the
ability of the compiler to evaluate the return value of strlen() and
the resulting execution flow in memcpy_and_pad(). It would be possible
to work around the problem by using sizeof(UTS_RELEASE) instead of
strlen(UTS_RELEASE), but that would only postpone the problem until the
function is called in a similar way. Uninline memcpy_and_pad() instead
to solve the problem for good.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The Xiaomi Mi Pad 2 is a Cherry Trail based x86 tablet which does not
use the i915's driver backlight control support:
i915 0000:00:02.0: [drm:intel_panel_setup_backlight [i915]] no backlight present per VBT
Like all Cherry Trail devices the ACPI tables on the Xiaomi Mi Pad 2
contain a broken ACPI-video implementation which causes 6 different
acpi_video backlights to get registered when used.
The lack of the i915 driver registering a BACKLIGHT_RAW (aka native) type
backlight causes acpi_video_get_backlight_type() to pick the broken
acpi_video backlight code as the backlight driver to use.
There actually is a separate lp8556 backlight controller connected
over I2C which gets registered as a BACKLIGHT_PLATFORM (aka vendor).
Add a quirk to force acpi_video_get_backlight_type() to return
acpi_backlight_vendor, so that the broken acpi_video backlight
interfaces do not get registered.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The .ident field of the dmi_system_id structs in the
video_detect_dmi_table[] is not used by the code.
Change all .ident = "..." assignments to comments, this reduces the
size of video_detect.o / video.ko by about 1500 bytes.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The handling of PMIC register reads through writing 0 to address 4
of the OpRegion is wrong. Instead of returning the read value
through the value64, which is a no-op for function == ACPI_WRITE calls,
store the value and then on a subsequent function == ACPI_READ with
address == 3 (the address for the value field of the OpRegion)
return the stored value.
This has been tested on a Xiaomi Mi Pad 2 and makes the ACPI battery dev
there mostly functional (unfortunately there are still other issues).
Here are the SET() / GET() functions of the PMIC ACPI device,
which use this OpRegion, which clearly show the new behavior to
be correct:
OperationRegion (REGS, 0x8F, Zero, 0x50)
Field (REGS, ByteAcc, NoLock, Preserve)
{
CLNT, 8,
SA, 8,
OFF, 8,
VAL, 8,
RWM, 8
}
Method (GET, 3, Serialized)
{
If ((AVBE == One))
{
CLNT = Arg0
SA = Arg1
OFF = Arg2
RWM = Zero
If ((AVBG == One))
{
GPRW = Zero
}
}
Return (VAL) /* \_SB_.PCI0.I2C7.PMI5.VAL_ */
}
Method (SET, 4, Serialized)
{
If ((AVBE == One))
{
CLNT = Arg0
SA = Arg1
OFF = Arg2
VAL = Arg3
RWM = One
If ((AVBG == One))
{
GPRW = One
}
}
}
Fixes: 0afa877a5650 ("ACPI / PMIC: intel: add REGS operation region support")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Remove the initialization of two static variables to false which is
pointless.
Signed-off-by: wangzhitong <wangzhitong@uniontech.com>
[ rjw: Subject and changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
EC interrupts constantly wake up system from s2idle, so set
ec_no_wakeup by default to keep the system in s2idle and reduce
energy consumption.
Signed-off-by: Binbin Zhou <zhoubinbin@uniontech.com>
[ rjw: Changelog and subject edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
In certain use cases (where the chip is part of a camera module, and the
camera module is wired together with a camera privacy LED), powering on
the device during probe is undesirable. Add support for the at24 to
execute probe while being in ACPI D state other than 0 (which means fully
powered on).
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Tell ACPI device PM code that the driver supports the device being in
non-zero ACPI D state when the driver's probe function is entered.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Add a convenience function to tell whether a device is in D0 state,
primarily for use in drivers' probe or remove functions on busses where
the custom is to power on the device for the duration of both.
Returns false on non-ACPI systems.
Suggested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Document the use of the _DSC object for setting desirable power state
during probe.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Enable drivers to tell ACPI that there's no need to power on a device for
probe. Drivers should still perform this by themselves if there's a need
to. In some cases powering on the device during probe is undesirable, and
this change enables a driver to choose what fits best for it.
Add a field called "flags" into struct i2c_driver for driver flags, and a
flag I2C_DRV_ACPI_WAIVE_D0_PROBE to tell a driver supports probe in ACPI D
states other than 0.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Acked-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Store a device's desired enumeration power state in struct
acpi_device_power during acpi_device object's initialisation.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Currently kdb contains some open-coded routines to generate a summary
character for each task. This code currently issues warnings, is
almost certainly broken and won't make sense to any kernel dev who
has ever used /proc to examine task states.
Fix both the warning and the potential for confusion by adopting the
scheduler's task classification. Whilst doing this we also simplify the
filtering by using mask strings directly (which means we don't have to
guess all the characters the scheduler might give us).
Unfortunately we can't quite match the scheduler classification completely.
We add four extra states: - for idle loops and i, m and s for sleeping
system daemons (which means kthreads in one of the I, M and S states).
These extra states are used to manage the filters for tools to make the
output of ps and bta less noisy.
Note: The Fixes below is the last point the original dubious code was
moved; it was not introduced by that patch. However it gives us
the last point to which this patch can be easily backported.
Happily that should be enough to cover the introduction of
CONFIG_WERROR!
Fixes: 2f064a59a11f ("sched: Change task_struct::state")
Link: https://lore.kernel.org/r/20211102173158.3315227-1-daniel.thompson@linaro.org
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
|
|
Properly document why changing PCI Class Code for GT64111 device to Host
Bridge is required as important details were after 20 years forgotten.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
