| Age | Commit message (Collapse) | Author |
|---|
|
On Blackfin SMP, a per-cpu loops_per_jiffy is pointless since both cores
always run at the same CCLK. In addition, the current implementation has
flaws since the main consumer for loops_per_jiffy (asm/delay.h) uses the
global kernel loops_per_jiffy and not the per_cpu one. So punt all of the
per-cpu handling and go back to the global shared one.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Change the bfin_gpio_pm_hibernate_restore() function to:
1) AND restored DATA with DIR (not OR) to get correct final state
2) Restore DATA before setting DIR to avoid glitches
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
The AD7142 add-on card hooks the IRQ line up to PG5, not PF5.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
The interrupt context save logic incorrectly stored the address of the
IPEND register rather than its value due to a missing dereference. While
we're here, also enable this code for all kernel debugging scenarios and
not just when KGDB is enabled.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
We already catch this anomaly at compile time, and the runtime version is
such that it ends up checking on all parts rather than just the ones that
might actually have it.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
The sed used to rename the bfin-twi-lcd only replaced the first instance
rather than all which led to the resources not being enabled when the
driver was built as a module.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
The Blackfin serial headers were inverting the CTS value leading to wrong
handling of the CTS line which broke CTS/RTS handling completely.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
This anomaly only applies to the BF527-0.1, not the BF526-0.1, and not any
other revision of the BF527. So make sure we don't go returning 0xffff
for other cases.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
The early logic to locate a free DMA channel and then set it up was broken
in a few ways that only manifested itself when we needed to set up more
than 2 on chip SRAM regions (most board defaults setup 1 or 2). First, we
checked the wrong status register (the destination gets updated, not the
source) and second, we did the ssync before rather than after resetting a
DMA config register.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Rather than assume Core B is always run with caches turned on, let people
load into any of the on-chip memory regions. It is their business how the
SRAM/Cache regions are utilized, so don't prevent them from being able to
load into them.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
The code used in the Blackfin lshrdi3 utilizes gcc constructs. However,
the structures declared don't line up with the code gcc generates, so
under certain optimizations, we get bad code and things crap out in fun
random ways. So rather than trying to maintain different gcc definitions
ourselves, just use the ones available in gcclib.h.
URL: http://blackfin.uclinux.org/gf/tracker/5286
Signed-off-by: Jie Zhang <jie.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Since we need to relocate the attached filesystem with the uClinux MTD map
(to handle some anomalies), we need to know its real filesize. If we boot
a kernel without a filesystem actually attached, we end up blindly reading
and copying garbage (since there is no magic value to detect validity).
Often times this results in an early crash and no output. So add a few
basic sanity checks before operating on things to catch the majority of
cases.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Previous unification code put the exception banner behind the "is oops"
logic when it should have been printed all the time.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Add missing anomaly workaround for anomaly 05000281 - we can't return to
instructions which cause hardware errors otherwise we trigger the error
again which means we go into an infinite loop of handling, returning, and
retriggering. This work around confuses gdb when the error occurs as the
PC will seemed to have moved, so a better long term fix will need to be
figured out, but for now this is better than an infinite crash loop.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
There are no CONFIG_{BLK,CHR}_DEV_FLASH Kconfig options, and there is no
flash_probe() function, so not really sure what this code is all about.
Seems to be dead code that stretches way back to the start of the Blackfin
port.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Improve the assembly with a few explanatory comments and use symbolic
defines rather than numeric values for bit positions.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
|
|
Get rid of extenddisksize parameter of ext3_get_blocks_handle(). This seems to
be a relict from some old days and setting disksize in this function does not
make much sence. Currently it was set only by ext3_getblk(). Since the
parameter has some effect only if create == 1, it is easy to check that the
three callers which end up calling ext3_getblk() with create == 1 (ext3_append,
ext3_quota_write, ext3_mkdir) do the right thing and set disksize themselves.
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
The following race can happen:
CPU1 CPU2
checkpointing code checks the buffer, adds
it to an array for writeback
do_get_write_access()
...
lock_buffer()
unlock_buffer()
flush_batch() submits the buffer for IO
__jbd_journal_file_buffer()
So a buffer under writeout is returned from do_get_write_access(). Since
the filesystem code relies on the fact that journaled buffers cannot be
written out, it does not take the buffer lock and so it can modify buffer
while it is under writeout. That can lead to a filesystem corruption
if we crash at the right moment. The similar problem can happen with
the journal_get_create_access() path.
We fix the problem by clearing the buffer dirty bit under buffer_lock
even if the buffer is on BJ_None list. Actually, we clear the dirty bit
regardless the list the buffer is in and warn about the fact if
the buffer is already journalled.
Thanks for spotting the problem goes to dingdinghua <dingdinghua85@gmail.com>.
Reported-by: dingdinghua <dingdinghua85@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Contents of long symlinks is written via standard write methods. So when the
write fails, we add inode to orphan list. But symlinks don't have .truncate
method defined so nobody properly removes them from the orphan list (both on
disk and in memory).
Fix this by calling ext3_truncate() directly instead of calling vmtruncate()
(which is saner anyway since we don't need anything vmtruncate() does except
from calling .truncate in these paths). We also add inode to orphan list only
if ext3_can_truncate() is true (currently, it can be false for symlinks when
there are no blocks allocated) - otherwise orphan list processing will complain
and ext3_truncate() will not remove inode from on-disk orphan list.
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Due to on disk corruption, it can happen that journal is too short. Fail
to load it in such case so that we don't oops somewhere later.
Reported-by: Nageswara R Sastry <rnsastry@linux.vnet.ibm.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Add appropriate MODULE_ALIAS() to facilitate autoloading of can protocol drivers
Signed-off-by: Lothar Wassmann <LW@KARO-electronics.de>
Acked-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix a use after free bug in can protocol drivers
The release functions of the can protocol drivers lack a call to
sock_orphan() which leads to referencing freed memory under certain
circumstances.
This patch fixes a bug reported here:
https://lists.berlios.de/pipermail/socketcan-users/2009-July/000985.html
Signed-off-by: Lothar Wassmann <LW@KARO-electronics.de>
Acked-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
ahci: add device ID for 82801JI sata controller
drivers/ata: Move a dereference below a NULL test
libata: implement and use HORKAGE_NOSETXFER, take#2
libata: fix follow-up SRST failure path
|
|
We need to check returning error for pci_register_driver(&joystick_driver)
On failure, we should unregister formerly registered audio drivers
This also fixed the compiler warning :
CC [M] sound/pci/riptide/riptide.o
sound/pci/riptide/riptide.c: In function ‘alsa_card_riptide_init’:
sound/pci/riptide/riptide.c:2200: warning: ignoring return value of ‘__pci_register_driver’, declared with attribute warn_unused_result
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Blue Microphones USB devices have an alternate setting that sends two
channels of data to the computer. Unfortunately, the descriptors of
that altsetting have a wrong channel setting, which means that any
recorded data from such a device has twice the sample rate from what
would be expected.
This patch adds a workaround to ignore that altsetting. Since these
devices have only one actual channel, no data is lost.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This patch fixes a bug in the image seq. number handling in the
scanning level. The assignment of the image_seq was incorrect.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
Do not forget to initialize 'gluebi->ubi_num' because otherwise
it will stay 0 even for ubi1 device, and gluebi will open
wrong UBI device when 'gluebi_get_device()' is called.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
When moving load_up_altivec to vector.S a typo in a comment caused a
thinko setting the wrong variable.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
On booke processors, gdb is seeing spurious SIGTRAPs when setting a
watchpoint.
user_disable_single_step() simply quits when the DAC is non-zero. It should
be clearing the DBCR0_IC and DBCR0_BT bits from the dbcr0 register and
TIF_SINGLESTEP from the thread flag.
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Need to adjust CUR_OFFSET for yorigin
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Allows us to hit dot clocks much closer, especially on
chips with non-27 Mhz reference clocks like most IGP chips.
This fixes most flickering and blanking problems with
non-exact dot clocks on these chips.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
This is needed when using fractional feedback dividers on some IGP
chips.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
RN50/ES1000 is a cut-down rv100 chip used in the server market.
The 3D engine on these is either not there or unverified so refuse
any attempt to configure registers on it.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Doing this like the DDX seems like the most sure fire way to avoid
having to reinvent it slowly and painfully. At the moment we keep
getting things wrong with aper vs vram, so we know the DDX does it right.
booted on PCI r100, PCIE rv370, IGP rs400.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
This add support for using dma32 memory on gpus that really need it.
Currently IGPs are left without DMA32 but we might need to change
that unless we can fix rs690.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
For now handle it via r/g/b offsets and disallow 16 bpp modes on big endian
machines.
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
On powerpc, since we aren't using any hw swappers, this will
get flipped around by default in hw.
tested on a G5 + rv515.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
If userspace sends a zero length IB, it really shouldn't have bothered
so EINVAL it.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Fix this to be correct like the DDX code, looks like a typo
on transfer to the kernel.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Noticed by Rafał Miłecki on dri-devel. On r6xx/r7xx hardware, laptop
panels can be driven by KLDSCP_LVTMA or UNIPHY.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The line mux for the connector in the bios tables
is used for enumerating drm connectors. Since
this laptop has a quirk where the same line much is
listed for both VGA and LVDS, the connectors get
combined. Setting the line mux on LVDS to an unused
value prevents both encoders from being combined into
the same connector. This should fix bko bug 13720.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
A bug caused a new caching state to be selected on each buffer object
validation regardless of the current caching state.
Moreover, a caching state could be selected that wasn't supported by
the memory type.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Userspace sends us a special relocation type to sync video/exa
to vlines to avoid tearing, this deals with the relocation
in the kernel, it picks the correct crtc and avoids issues
where crtcs are disabled.
This version also parses the wait until to make sure it isn't
trying to do anything evil.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Normally we are free to place VRAM where we want in the GPUs
memory address space, however on IGP chips the VRAM is actual RAM,
and no special translation or aperture is used inside the GPU MC.
So when you move the VRAM aperture away from the TOM register,
you actually move it into main memory and can trash things quite badly.
This commit makes the code respect the TOM location for MC_FB_LOCATION.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The crtc and cursor offsets on the legacy chips are offset from
DISPLAY_BASE_ADDR. The code worked if display base addr was at 0,
but otherwise falls to pieces.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
If there is a problem then this is hiding it, we shouldn't
ever need to flush the IB. Either the buffers are:
WB - caching just works.
WC - no need to do explicit flush, the MB + readback will do it
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Unsigned long is incorrect for 64-bit resources on 32-bit hw.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
