| Age | Commit message (Collapse) | Author |
|---|
|
The change fixes sleep in atomic context bug, which is encountered
every time when link settings are changed by ethtool.
Since commit 35b5f6b1a82b ("PHYLIB: Locking fixes for PHY I/O
potentially sleeping") phy_start_aneg() function utilizes a mutex
to serialize changes to phy state, however that helper function is
called in atomic context under a grabbed spinlock, because
phy_start_aneg() is called by phy_ethtool_ksettings_set() and by
replaced phy_ethtool_sset() helpers from phylib.
Now duplex mode setting is enforced in sh_eth_adjust_link() only,
also now RX/TX is disabled when link is put down or modifications
to E-MAC registers ECMR and GECMR are expected for both cases of
checked and ignored link status pin state from E-MAC interrupt handler.
For reference the change is a partial rework of commit 1e1b812bbe10
("sh_eth: fix handling of no LINK signal").
Fixes: dc19e4e5e02f ("sh: sh_eth: Add support ethtool")
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit 35b5f6b1a82b ("PHYLIB: Locking fixes for PHY I/O
potentially sleeping") phy_start_aneg() function utilizes a mutex
to serialize changes to phy state, however the helper function is
called in atomic context.
The bug can be reproduced by running "ethtool -r" command, the bug
is reported if CONFIG_DEBUG_ATOMIC_SLEEP build option is enabled.
Fixes: dc19e4e5e02f ("sh: sh_eth: Add support ethtool")
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jiong Wang says:
====================
NFP supports u16 and u32 multiplication. Multiplication is done 8-bits per
step, therefore we need 2 steps for u16 and 4 steps for u32.
We also need one start instruction to initialize the sequence and one or
two instructions to fetch the result depending on either you need the high
halve of u32 multiplication.
For ALU64, if either operand is beyond u32's value range, we reject it. One
thing to note, if the source operand is BPF_K, then we need to check "imm"
field directly, and we'd reject it if it is negative. Because for ALU64,
"imm" (with s32 type) is expected to be sign extended to s64 which NFP mul
doesn't support. For ALU32, it is fine for "imm" be negative though,
because the result is 32-bits and here is no difference on the low halve
of result for signed/unsigned mul, so we will get correct result.
NFP doesn't have integer divide instruction, this patch set uses reciprocal
algorithm (the basic one, reciprocal_div) to emulate it.
For each u32 divide, we would need 11 instructions to finish the operation.
7 (for multiplication) + 4 (various ALUs) = 11
Given NFP only supports multiplication no bigger than u32, we'd require
divisor and dividend no bigger than that as well.
Also eBPF doesn't support signed divide and has enforced this on C language
level by failing compilation. However LLVM assembler hasn't enforced this,
so it is possible for negative constant to leak in as a BPF_K operand
through assembly code, we reject such cases as well.
Meanwhile reciprocal_div.h only implemented the basic version of:
"Division by Invariant Integers Using Multiplication"
- Torbjörn Granlund and Peter L. Montgomery
This patch set further implements the optimized version (Figure 4.2 in the
paper) inside existing reciprocal_div.h. When the divider is even and the
calculated reciprocal magic number doesn't fit u32, we could reduce the
required ALU instructions from 4 to 2 or 1 for some cases.
The advanced version requires more complex calculation to get the
reciprocal multiplier and other control variables, but then could reduce
the required emulation operations. It makes sense to use it for JIT divide
code generation (for example eBPF JIT backends) for which we are willing to
trade performance of JITed code with that of host.
v2:
- add warning in l == 32 code path. (Song Liu/Jakub)
- jit separate insn sequence for l == 32. (Jakub/Edwin)
- should use unrestricted operand for mul.
- once place should use "1U << exp" instead of "1 << exp".
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
As we are doing JIT, we would want to use the advanced version of the
reciprocal divide (reciprocal_value_adv) to trade performance with host.
We could reduce the required ALU instructions from 4 to 2 or 1.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
NFP doesn't have integer divide instruction, this patch use reciprocal
algorithm (the basic one, reciprocal_div) to emulate it.
For each u32 divide, we would need 11 instructions to finish the operation.
7 (for multiplication) + 4 (various ALUs) = 11
Given NFP only supports multiplication no bigger than u32, we'd require
divisor and dividend no bigger than that as well.
Also eBPF doesn't support signed divide and has enforced this on C language
level by failing compilation. However LLVM assembler hasn't enforced this,
so it is possible for negative constant to leak in as a BPF_K operand
through assembly code, we reject such cases as well.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
NFP supports u16 and u32 multiplication. Multiplication is done 8-bits per
step, therefore we need 2 steps for u16 and 4 steps for u32.
We also need one start instruction to initialize the sequence and one or
two instructions to fetch the result depending on either you need the high
halve of u32 multiplication.
For ALU64, if either operand is beyond u32's value range, we reject it. One
thing to note, if the source operand is BPF_K, then we need to check "imm"
field directly, and we'd reject it if it is negative. Because for ALU64,
"imm" (with s32 type) is expected to be sign extended to s64 which NFP mul
doesn't support. For ALU32, it is fine for "imm" be negative though,
because the result is 32-bits and here is no difference on the low halve
of result for signed/unsigned mul, so we will get correct result.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
NFP verifier hook is coping range information of the shift amount for
indirect shift operation so optimized shift sequences could be generated.
We want to use range info to do more things. For example, to decide whether
multiplication and divide are supported on the given range.
This patch simply let NFP verifier hook to copy range info for all operands
of all ALU operands.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
The two fields are a copy of umin and umax info of bpf_insn->src_reg
generated by verifier.
Rename to make their meaning clear.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
The new added "reciprocal_value_adv" implements the advanced version of the
algorithm described in Figure 4.2 of the paper except when
"divisor > (1U << 31)" whose ceil(log2(d)) result will be 32 which then
requires u128 divide on host. The exception case could be easily handled
before calling "reciprocal_value_adv".
The advanced version requires more complex calculation to get the
reciprocal multiplier and other control variables, but then could reduce
the required emulation operations.
It makes no sense to use this advanced version for host divide emulation,
those extra complexities for calculating multiplier etc could completely
waive our saving on emulation operations.
However, it makes sense to use it for JIT divide code generation (for
example eBPF JIT backends) for which we are willing to trade performance of
JITed code with that of host. As shown by the following pseudo code, the
required emulation operations could go down from 6 (the basic version) to 3
or 4.
To use the result of "reciprocal_value_adv", suppose we want to calculate
n/d, the C-style pseudo code will be the following, it could be easily
changed to real code generation for other JIT targets.
struct reciprocal_value_adv rvalue;
u8 pre_shift, exp;
// handle exception case.
if (d >= (1U << 31)) {
result = n >= d;
return;
}
rvalue = reciprocal_value_adv(d, 32)
exp = rvalue.exp;
if (rvalue.is_wide_m && !(d & 1)) {
// floor(log2(d & (2^32 -d)))
pre_shift = fls(d & -d) - 1;
rvalue = reciprocal_value_adv(d >> pre_shift, 32 - pre_shift);
} else {
pre_shift = 0;
}
// code generation starts.
if (imm == 1U << exp) {
result = n >> exp;
} else if (rvalue.is_wide_m) {
// pre_shift must be zero when reached here.
t = (n * rvalue.m) >> 32;
result = n - t;
result >>= 1;
result += t;
result >>= rvalue.sh - 1;
} else {
if (pre_shift)
result = n >> pre_shift;
result = ((u64)result * rvalue.m) >> 32;
result >>= rvalue.sh;
}
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
This commit adds a bash completion to the bpftool cgroup tree
command.
Signed-off-by: Roman Gushchin <guro@fb.com>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Cc: Quentin Monnet <quentin.monnet@netronome.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Alexei Starovoitov <ast@kernel.org>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Describe cgroup tree command in the corresponding bpftool man page.
Signed-off-by: Roman Gushchin <guro@fb.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Cc: Quentin Monnet <quentin.monnet@netronome.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
This commit introduces a new bpftool command: cgroup tree.
The idea is to iterate over the whole cgroup tree and print
all attached programs.
I was debugging a bpf/systemd issue, and found, that there is
no simple way to listen all bpf programs attached to cgroups.
I did master something in bash, but after some time got tired of it,
and decided, that adding a dedicated bpftool command could be
a better idea.
So, here it is:
$ sudo ./bpftool cgroup tree
CgroupPath
ID AttachType AttachFlags Name
/sys/fs/cgroup/system.slice/systemd-machined.service
18 ingress
17 egress
/sys/fs/cgroup/system.slice/systemd-logind.service
20 ingress
19 egress
/sys/fs/cgroup/system.slice/systemd-udevd.service
16 ingress
15 egress
/sys/fs/cgroup/system.slice/systemd-journald.service
14 ingress
13 egress
Signed-off-by: Roman Gushchin <guro@fb.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Cc: Quentin Monnet <quentin.monnet@netronome.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
This implements extended LE craete connection and enhanced
LE conn complete event if the controller supports.
For now it is as good as legacy LE connection and event as
no new features in the extended connection is handled.
< HCI Command: LE Extended Create Connection (0x08|0x0043) plen 26
Filter policy: White list is not used (0x00)
Own address type: Public (0x00)
Peer address type: Random (0x01)
Peer address: DB:7E:2E:1D:85:E8 (Static)
Initiating PHYs: 0x01
Entry 0: LE 1M
Scan interval: 60.000 msec (0x0060)
Scan window: 60.000 msec (0x0060)
Min connection interval: 50.00 msec (0x0028)
Max connection interval: 70.00 msec (0x0038)
Connection latency: 0 (0x0000)
Supervision timeout: 420 msec (0x002a)
Min connection length: 0.000 msec (0x0000)
Max connection length: 0.000 msec (0x0000)
> HCI Event: Command Status (0x0f) plen 4
LE Extended Create Connection (0x08|0x0043) ncmd 2
Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 31
LE Enhanced Connection Complete (0x0a)
Status: Success (0x00)
Handle: 3585
Role: Master (0x00)
Peer address type: Random (0x01)
Peer address: DB:7E:2E:1D:85:E8 (Static)
Local resolvable private address: 00:00:00:00:00:00 (Non-Resolvable)
Peer resolvable private address: 00:00:00:00:00:00 (Non-Resolvable)
Connection interval: 67.50 msec (0x0036)
Connection latency: 0 (0x0000)
Supervision timeout: 420 msec (0x002a)
Master clock accuracy: 0x00
@ MGMT Event: Device Connected (0x000b) plen 40
LE Address: DB:7E:2E:1D:85:E8 (Static)
Flags: 0x00000000
Data length: 27
Name (complete): Designer Mouse
Appearance: Mouse (0x03c2)
Flags: 0x05
LE Limited Discoverable Mode
BR/EDR Not Supported
16-bit Service UUIDs (complete): 1 entry
Human Interface Device (0x1812)
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This is used by the host to talk to the BMC's PCIe slave device. The BMC
is not involved, but the clock needs to be enabled so the host can use
the device.
Fixes: 15ed8ce5f84e ("clk: aspeed: Register gated clocks")
Cc: stable@vger.kernel.org # 4.15
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Tested-by: Lei YU <mine260309@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
This is done so that the helpers can be used for extended conn
implementation which will be done in subsequent patch.
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch enables Extended ADV report event if extended scanning
is supported in the controller and process the same.
The new features are not handled and for now its as good as
legacy ADV report.
> HCI Event: LE Meta Event (0x3e) plen 53
LE Extended Advertising Report (0x0d)
Num reports: 1
Entry 0
Event type: 0x0013
Props: 0x0013
Connectable
Scannable
Use legacy advertising PDUs
Data status: Complete
Legacy PDU Type: ADV_IND (0x0013)
Address type: Random (0x01)
Address: DB:7E:2E:1A:85:E8 (Static)
Primary PHY: LE 1M
Secondary PHY: LE 1M
SID: 0x00
TX power: 0 dBm
RSSI: -90 dBm (0xa6)
Periodic advertising invteral: 0.00 msec (0x0000)
Direct address type: Public (0x00)
Direct address: 00:00:00:00:00:00 (OUI 00-00-00)
Data length: 0x1b
0f 09 44 65 73 69 67 6e 65 72 20 4d 6f 75 73 65 ..Designer Mouse
03 19 c2 03 02 01 05 03 03 12 18 ...........
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This implements Set extended scan param and set extended scan enable
commands and use it for start LE scan based on controller support.
The new features added in these commands are setting of new PHY for
scanning and setting of scan duration. Both features are disabled
for now, meaning only 1M PHY is set and scan duration is set to 0
which means that scanning will be done untill scan disable is called.
< HCI Command: LE Set Extended Scan Parameters (0x08|0x0041) plen 8
Own address type: Random (0x01)
Filter policy: Accept all advertisement (0x00)
PHYs: 0x01
Entry 0: LE 1M
Type: Active (0x01)
Interval: 11.250 msec (0x0012)
Window: 11.250 msec (0x0012)
> HCI Event: Command Complete (0x0e) plen 4
LE Set Extended Scan Parameters (0x08|0x0041) ncmd 1
Status: Success (0x00)
< HCI Command: LE Set Extended Scan Enable (0x08|0x0042) plen 6
Extended scan: Enabled (0x01)
Filter duplicates: Enabled (0x01)
Duration: 0 msec (0x0000)
Period: 0.00 sec (0x0000)
> HCI Event: Command Complete (0x0e) plen 4
LE Set Extended Scan Enable (0x08|0x0042) ncmd 2
Status: Success (0x00)
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Introduce a helper hci_req_start_scan() which starts an LE
scan and call it from passive_Scan() and active_scan().
There is not functionality change in this patch.
This is basically done to enable extended scanning if the
controller supports which will be done in the subsequent
patch
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"The usual collection of driver fixlets:
- build cleanup/fix for the sunxi makefile that tried to save size
but failed and prevented dead code elimination from working
- two Davinci clk driver fixes for a typo causing build failures in
different configurations and an error check that checks the wrong
variable.
- undo the DT ABI breaking imx6ul binding header shuffle that got
merged this cycle"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
dt-bindings: clock: imx6ul: Do not change the clock definition order
clk: davinci: fix a typo (which leads to build failures)
clk: davinci: cfgchip: testing the wrong variable
clk: sunxi-ng: replace lib-y with obj-y
|
|
Pull VFIO fixes from Alex Williamson:
- Make vfio-pci IGD extensions optional via Kconfig (Alex Williamson)
- Remove unused and soon to be removed map_atomic callback from mbochs
sample driver, add unmap callback to avoid dmabuf leaks (Gerd
Hoffmann)
- Fix usage of get_user_pages_longterm() (Jason Gunthorpe)
- Fix sample mbochs driver vm_operations_struct.fault return type
(Souptick Joarder)
* tag 'vfio-v4.18-rc4' of git://github.com/awilliam/linux-vfio:
sample/vfio-mdev: Change return type to vm_fault_t
vfio: Use get_user_pages_longterm correctly
sample/mdev/mbochs: add mbochs_kunmap_dmabuf
sample/mdev/mbochs: remove mbochs_kmap_atomic_dmabuf
vfio/pci: Make IGD support a configurable option
|
|
Patch (7705bb7176b9 clk: qcom: mmcc-msm8996: leave all mmagic gdscs
and clocks always enabled") makes all mmgaic gdscs ALWAYS_ON.
The mmagic_bimc_gdsc is also needed to be turned on to get display
working on 8x96.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Fixes: 7705bb7176b9 ("clk: qcom: mmcc-msm8996: leave all mmagic gdscs and clocks always enabled")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
into clk-fixes
Pull Amlogic clk driver fixes from Jerome Brunet:
These are two simple fixes, yet the first one is quite important as it
solves boots hangs we've been having when FDIV2 gets disabled. This did
not show up before because this particular clock is heavily used and
only gets disabled for a very short period of time before modules (such
as ethernet or emmc) probe.
- fix boot issue with gxbb and gxl platforms
- fix racalculation error in the clk_audio_divider
* tag 'meson-clk-fixes-4.18-1' of https://github.com/BayLibre/clk-meson:
clk: meson: audio-divider is one based
clk: meson-gxbb: set fclk_div2 as CLK_IS_CRITICAL
|
|
On some systems, we come out of the bootloader with some
gates set with the clock "enabled" but the reset also
asserted.
Since 8a53fc511c5e "clk: aspeed: Prevent reset if clock is enabled"
we check that enabled bit in aspeed_clk_enabled(), and do
nothing if already set.
This breaks when the above scenario occurs, as the clock
is enabled, but the reset still needs to be lifted.
This patch fixes it by also checking the reset bit (if any)
and treating a gate in "reset" as being disabled.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fixes: 8a53fc511c5e "clk: aspeed: Prevent reset if clock is enabled"
Cc: Eddie James <eajames@linux.vnet.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The last-minute fold-in of the ENTRY() macro did change behavior:
instead of printing the symbolic name (e.g. "CLK_IS_BASIC"), it prints
the expansion of it (e.g. "(1UL << (5))").
Use "#" instead of __stringify() to fix this.
Fixes: a6059ab98130fb56 ("clk: Show symbolic clock flags in debugfs")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Commit 12d807cd34b8 ("clk: qcom: gcc-msm8996: Disable halt check on UFS
clocks") marked BRANCH_HALT_SKIP for ufs rx clocks, but missed ufs tx
clocks. The result of that is kernel warnings at reboot:
[ 105.624283] gcc_ufs_tx_symbol_0_clk status stuck at 'on'
[ 105.624311] WARNING: CPU: 1 PID: 1 at drivers/clk/qcom/clk-branch.c:100 clk_branch_toggle+0x190/0x1b0
[ 105.633235] Modules linked in:
[ 105.645118] CPU: 1 PID: 1 Comm: systemd-shutdow Tainted: G W 4.18.0-rc2-00002-g2bfbe52a53a3 #11
[ 105.647988] Hardware name: Qualcomm Technologies, Inc. DB820c (DT)
[ 105.657966] pstate: 60000085 (nZCv daIf -PAN -UAO)
[ 105.664127] pc : clk_branch_toggle+0x190/0x1b0
[ 105.668900] lr : clk_branch_toggle+0x190/0x1b0
[ 105.673324] sp : ffff00000805bb40
[ 105.677751] x29: ffff00000805bb40 x28: 0000000000000000
[ 105.681140] x27: ffff8000d947cc60 x26: 0000000000000001
[ 105.686520] x25: ffff000008f71900 x24: 0000000000000000
[ 105.691816] x23: ffff00000925e338 x22: ffff00000855f8e0
[ 105.697114] x21: 0000000000000000 x20: 0000000000000000
[ 105.702407] x19: ffff0000091c9000 x18: ffffffffffffffff
[ 105.707702] x17: 0000ffffac148c58 x16: ffff000008b82928
[ 105.712998] x15: ffff0000091c96c8 x14: ffff0000893817c7
[ 105.718293] x13: ffff0000093817d5 x12: ffff0000091c9940
[ 105.723587] x11: ffff0000085e3e70 x10: ffff00000805b780
[ 105.728884] x9 : ffff00000805bb40 x8 : 7320737574617473
[ 105.734179] x7 : 206b6c635f305f6c x6 : 00000000000001e5
[ 105.739472] x5 : 0000000000000000 x4 : 0000000000000000
[ 105.744769] x3 : ffffffffffffffff x2 : ffff0000091e2658
[ 105.750063] x1 : a7c4712dd5e09c00 x0 : 0000000000000000
[ 105.755360] Call trace:
[ 105.760652] clk_branch_toggle+0x190/0x1b0
[ 105.762824] clk_branch2_disable+0x18/0x20
[ 105.766994] clk_core_disable+0x58/0xa8
[ 105.771069] clk_core_disable_lock+0x20/0x38
[ 105.774803] clk_disable+0x1c/0x28
[ 105.779320] __ufshcd_setup_clocks+0x298/0x308
[ 105.782529] ufshcd_suspend+0x160/0x308
[ 105.786953] ufshcd_shutdown+0x38/0xa0
[ 105.790690] ufshcd_pltfrm_shutdown+0x10/0x18
[ 105.794512] platform_drv_shutdown+0x20/0x30
[ 105.798935] device_shutdown+0x110/0x1e8
[ 105.803278] kernel_restart_prepare+0x34/0x40
[ 105.807181] kernel_restart+0x14/0x78
[ 105.811434] sys_reboot+0x200/0x248
[ 105.815081] el0_svc_naked+0x30/0x34
[ 105.818378] ---[ end trace 8d2322276b27879c ]---
Mark gcc_ufs_tx_symbol_0_clk as BRANCH_HALT_SKIP as well.
Fixes: 12d807cd34b8 ("clk: qcom: gcc-msm8996: Disable halt check on UFS clocks")
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
This patch disallows rbtree with single elements, which is causing
problems with the recent timeout support. Before this patch, you
could opt out individual set representations per module, which is
just adding extra complexity.
Fixes: 8d8540c4f5e0("netfilter: nft_set_rbtree: add timeout support")
Reported-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"A few more changes for v4.18:
- wire up the two new system calls io_pgetevents and rseq
- fix a register corruption in the expolines code for machines
without EXRL
- drastically reduce the memory utilization of the dasd driver
- fix reference counting for KVM page table pages"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: wire up rseq system call
s390: wire up io_pgetevents system call
s390/mm: fix refcount usage for 4K pgste
s390/dasd: reduce the default queue depth and nr of hardware queues
s390: Correct register corruption in critical section cleanup
|
|
RTL8822be can't bring up properly on ASUS X530UN, and dmesg says:
[ 8.591333] r8822be: module is from the staging directory, the quality
is unknown, you have been warned.
[ 8.593122] r8822be 0000:02:00.0: enabling device (0000 -> 0003)
[ 8.669163] r8822be: Using firmware rtlwifi/rtl8822befw.bin
[ 9.289939] r8822be: rtlwifi: wireless switch is on
[ 10.056426] r8822be 0000:02:00.0 wlp2s0: renamed from wlan0
...
[ 11.952534] r8822be: halmac_init_hal failed
[ 11.955933] r8822be: halmac_init_hal failed
[ 11.956227] r8822be: halmac_init_hal failed
[ 22.007942] r8822be: halmac_init_hal failed
Jian-Hong reported it works if turn off ASPM with module parameter aspm=0.
In order to fix this problem kindly, this commit don't turn off aspm but
enlarge ASPM L1 latency to 7.
Reported-by: Jian-Hong Pan <jian-hong@endlessm.com>
Tested-by: Jian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In general, accessing userspace memory beyond the length of the supplied
buffer in VFS read/write handlers can lead to both kernel memory corruption
(via kernel_read()/kernel_write(), which can e.g. be triggered via
sys_splice()) and privilege escalation inside userspace.
Fix it by using simple_read_from_buffer() instead of custom logic.
Fixes: 6bc235a2e24a ("USB: add driver for Meywa-Denki & Kayac YUREX")
Signed-off-by: Jann Horn <jannh@google.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 2f28e4c24b10e (thermal: armada: Clarify control registers
accesses) introduced the new thermal binding. The new binding extends
the second registers field size to 8. Switch to the new binding to fix
thermal reading values. Without this change the fix for errata #132698
introduced in commit 8c0b888f661 (thermal: armada: Change sensors trim
default value) has no effect.
Cc: stable@vger.kernel.org # v4.16+
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Corsair Strafe appears to suffer from the same issues
as the Corsair Strafe RGB.
Apply the same quirks (control message delay and init delay)
that the RGB version has to 1b1c:1b15.
With these quirks in place the keyboard works correctly upon
booting the system, and no longer requires reattaching the device.
Signed-off-by: Nico Sneck <snecknico@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The > should be >= here so that we don't read one element beyond the end
of the ep->stream_info->stream_rings[] array.
Fixes: e9df17eb1408 ("USB: xhci: Correct assumptions about number of rings per endpoint.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Without that option, we run into a link failure:
drivers/usb/gadget/udc/aspeed-vhub/hub.o: In function `ast_vhub_std_hub_request':
hub.c:(.text+0x5b0): undefined reference to `usb_gadget_get_string'
Fixes: 7ecca2a4080c ("usb/gadget: Add driver for Aspeed SoC virtual hub")
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This parameter introduced several years ago in the XHCI host controller
driver was somehow left undocumented. Add a few lines in the kernel
parameters text.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
USB-serial fixes for v4.18-rc4
Here are three fixes for broken control-transfer error handling, which
could lead to uninitialised slab data leaking to user space.
Included is also a new device id for cp210x.
All but the final two patches have been in linux-next with no reported
issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
The comment is the same as in the top-level Makefile.
Also, the comments contain typos:
- the .PHONY variable -> the PHONY variable
- se we can ... -> so we can ...
Instead of fixing the typos, just remove the duplicated comments.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
.PHONY is a target, not a variable.
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The comment line for addtree says "skip if -I has no parameter".
What it actually does is "drop if -I has no parameter". For example,
if you have the compiler flag '-I foo' (a space between), it will be
converted to 'foo'. This completely changes the meaning.
What we want is, "do nothing" for -I without parameter so that
'-I foo' is kept as-is.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Add usage info for the Kbuild environment variable KBUILD_KCONFIG.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Update Documentation/kbuild/kconfig.txt, which mostly contains
user help for using the kernel config tools.
- Add mention of 'nconfig' embedded help text.
- Make the section on new config symbols readable.
- Correct how to find menuconfig search help.
- Add section on 'nconfig' usage.
- Mention that gconfig has multiple viewing modes/options.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Removed Kbuild documentation for INSTALL_FW_PATH.
The kbuild symbol INSTALL_FW_PATH was removed from Kbuild tools in
September 2017 (for 4.14) but the symbol was not deleted from
the kbuild documentation, so do that now.
Fixes: 5620a0d1aacd ("firmware: delete in-kernel firmware")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: stable@vger.kernel.org # 4.14+
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The supported alias for building sparc 32-bit is "sparc32",
not "sparc", so update the alias documentation for that.
Just using "sparc" produces a 64-bit config file.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
In Kbuild documentation, add alias for 64-bit sh ARCH ("sh64")
to the list of ARCH aliases.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The current implementation of cfg80211_rx_control_port assumed that the
caller could provide a contiguous region of memory for the control port
frame to be sent up to userspace. Unfortunately, many drivers produce
non-linear skbs, especially for data frames. This resulted in userspace
getting notified of control port frames with correct metadata (from
address, port, etc) yet garbage / nonsense contents, resulting in bad
handshakes, disconnections, etc.
mac80211 linearizes skbs containing management frames. But it didn't
seem worthwhile to do this for control port frames. Thus the signature
of cfg80211_rx_control_port was changed to take the skb directly.
nl80211 then takes care of obtaining control port frame data directly
from the (linear | non-linear) skb.
The caller is still responsible for freeing the skb,
cfg80211_rx_control_port does not take ownership of it.
Fixes: 6a671a50f819 ("nl80211: Add CMD_CONTROL_PORT_FRAME API")
Signed-off-by: Denis Kenzior <denkenz@gmail.com>
[fix some kernel-doc formatting, add fixes tag]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This patch fixes a silent out-of-bound read possibility that was present
because of the misuse of this function.
Mostly it was called with a struct udphdr *hp which had only the udphdr
part linearized by the skb_header_pointer, however
nf_tproxy_get_sock_v{4,6} uses it as a tcphdr pointer, so some reads for
tcp specific attributes may be invalid.
Fixes: a583636a83ea ("inet: refactor inet[6]_lookup functions to take skb")
Signed-off-by: Máté Eckl <ecklm94@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Nothing in tree use this header which seems a remains of a staging
driver.
This patch remove it.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
We have two new lenovo desktop models which need to apply the fixup of
ALC294_FIXUP_LENOVO_MIC_LOCATION, and they have the same pin cfg as
the machine with subsystem id:0x17aa3136, now use the pincfg table
to apply the fixup for them.
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Check for Resolv list supported by controller. So check the supported
commmand first before issuing this command i.e.,HCI_OP_LE_CLEAR_RESOLV_LIST
Before patch:
< HCI Command: LE Read White List... (0x08|0x000f) plen 0 #55 [hci0] 13.338168
> HCI Event: Command Complete (0x0e) plen 5 #56 [hci0] 13.338842
LE Read White List Size (0x08|0x000f) ncmd 1
Status: Success (0x00)
Size: 25
< HCI Command: LE Clear White List (0x08|0x0010) plen 0 #57 [hci0] 13.339029
> HCI Event: Command Complete (0x0e) plen 4 #58 [hci0] 13.339939
LE Clear White List (0x08|0x0010) ncmd 1
Status: Success (0x00)
< HCI Command: LE Read Resolving L.. (0x08|0x002a) plen 0 #59 [hci0] 13.340152
> HCI Event: Command Complete (0x0e) plen 5 #60 [hci0] 13.340952
LE Read Resolving List Size (0x08|0x002a) ncmd 1
Status: Success (0x00)
Size: 25
< HCI Command: LE Read Maximum Dat.. (0x08|0x002f) plen 0 #61 [hci0] 13.341180
> HCI Event: Command Complete (0x0e) plen 12 #62 [hci0] 13.341898
LE Read Maximum Data Length (0x08|0x002f) ncmd 1
Status: Success (0x00)
Max TX octets: 251
Max TX time: 17040
Max RX octets: 251
Max RX time: 17040
After patch:
< HCI Command: LE Read White List... (0x08|0x000f) plen 0 #55 [hci0] 28.919131
> HCI Event: Command Complete (0x0e) plen 5 #56 [hci0] 28.920016
LE Read White List Size (0x08|0x000f) ncmd 1
Status: Success (0x00)
Size: 25
< HCI Command: LE Clear White List (0x08|0x0010) plen 0 #57 [hci0] 28.920164
> HCI Event: Command Complete (0x0e) plen 4 #58 [hci0] 28.920873
LE Clear White List (0x08|0x0010) ncmd 1
Status: Success (0x00)
< HCI Command: LE Read Resolving L.. (0x08|0x002a) plen 0 #59 [hci0] 28.921109
> HCI Event: Command Complete (0x0e) plen 5 #60 [hci0] 28.922016
LE Read Resolving List Size (0x08|0x002a) ncmd 1
Status: Success (0x00)
Size: 25
< HCI Command: LE Clear Resolving... (0x08|0x0029) plen 0 #61 [hci0] 28.922166
> HCI Event: Command Complete (0x0e) plen 4 #62 [hci0] 28.922872
LE Clear Resolving List (0x08|0x0029) ncmd 1
Status: Success (0x00)
< HCI Command: LE Read Maximum Dat.. (0x08|0x002f) plen 0 #63 [hci0] 28.923117
> HCI Event: Command Complete (0x0e) plen 12 #64 [hci0] 28.924030
LE Read Maximum Data Length (0x08|0x002f) ncmd 1
Status: Success (0x00)
Max TX octets: 251
Max TX time: 17040
Max RX octets: 251
Max RX time: 17040
Signed-off-by: Ankit Navik <ankit.p.navik@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
When the controller supports the Read LE Resolv List size feature, the
maximum list size are read and now stored.
Before patch:
< HCI Command: LE Read White List... (0x08|0x000f) plen 0 #55 [hci0] 17.979791
> HCI Event: Command Complete (0x0e) plen 5 #56 [hci0] 17.980629
LE Read White List Size (0x08|0x000f) ncmd 1
Status: Success (0x00)
Size: 25
< HCI Command: LE Clear White List (0x08|0x0010) plen 0 #57 [hci0] 17.980786
> HCI Event: Command Complete (0x0e) plen 4 #58 [hci0] 17.981627
LE Clear White List (0x08|0x0010) ncmd 1
Status: Success (0x00)
< HCI Command: LE Read Maximum Dat.. (0x08|0x002f) plen 0 #59 [hci0] 17.981786
> HCI Event: Command Complete (0x0e) plen 12 #60 [hci0] 17.982636
LE Read Maximum Data Length (0x08|0x002f) ncmd 1
Status: Success (0x00)
Max TX octets: 251
Max TX time: 17040
Max RX octets: 251
Max RX time: 17040
After patch:
< HCI Command: LE Read White List... (0x08|0x000f) plen 0 #55 [hci0] 13.338168
> HCI Event: Command Complete (0x0e) plen 5 #56 [hci0] 13.338842
LE Read White List Size (0x08|0x000f) ncmd 1
Status: Success (0x00)
Size: 25
< HCI Command: LE Clear White List (0x08|0x0010) plen 0 #57 [hci0] 13.339029
> HCI Event: Command Complete (0x0e) plen 4 #58 [hci0] 13.339939
LE Clear White List (0x08|0x0010) ncmd 1
Status: Success (0x00)
< HCI Command: LE Read Resolving L.. (0x08|0x002a) plen 0 #59 [hci0] 13.340152
> HCI Event: Command Complete (0x0e) plen 5 #60 [hci0] 13.340952
LE Read Resolving List Size (0x08|0x002a) ncmd 1
Status: Success (0x00)
Size: 25
< HCI Command: LE Read Maximum Dat.. (0x08|0x002f) plen 0 #61 [hci0] 13.341180
> HCI Event: Command Complete (0x0e) plen 12 #62 [hci0] 13.341898
LE Read Maximum Data Length (0x08|0x002f) ncmd 1
Status: Success (0x00)
Max TX octets: 251
Max TX time: 17040
Max RX octets: 251
Max RX time: 17040
Signed-off-by: Ankit Navik <ankit.p.navik@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The USB completion callback does not disable interrupts while acquiring
the ->lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave variant of the locking primitives.
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: linux-bluetooth@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
