| Age | Commit message (Collapse) | Author |
|---|
|
According to the reference manual the shp_2_mcu / mcu_2_shp
scripts must be used for devices connected through the SPBA.
This fixes an issue we saw with DMA transfers from SPI NOR Flashes.
Sometimes the SPI controller RX FIFO was not empty after a DMA
transfer and the driver got stuck in the next PIO transfer when
it read one word more than expected.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add the carrier boards 3.3V supply as fixed regulator. This allows
to specify the power supply for nodes like backlight.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Colibri modules need to be powered using the power pins 3V3 and
AVDD_AUDIO. Add fixed regulators which represent this power rails.
Potentially, those power rails could be switched on a carrier
board. A carrier board device tree could add a own regulator with
a GPIO, and reference that regulator in a vin-supply property of
those new module level system regulators.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Drop the fake simple-bus container 'regulators' and put the
regulators directly under the root node. This also makes the
artificial 'reg' properties superfluous. While at it, remove
the unnecessary regulator-always-on property and name the
regulators according to schematics.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Assign Ethernet clock parents explicitly. The Colibri VF61
uses the 50MHz Ethernet clock provided by PLL5.
The Vybrid SoC has two ethernet interfaces (fec0 and fec1) which
use the same clock source (VF610_CLK_ENET). Therefore this parent
configuration affects multiple consumer devices and need to be
specified in the clock provider node.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Assign Ethernet clock parents explicitly. The VF610 Tower Board
uses the external Ethernet clock input which is connected to
a 50MHz clock.
The Vybrid SoC has two ethernet interfaces (fec0 and fec1) which
use the same clock source (VF610_CLK_ENET). Therefore this parent
configuration affects multiple consumer devices and need to be
specified in the clock provider node.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Signed-off-by: Soeren Moch <smoch@web.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Remove the following unnecessary iomuxc container nodes:
imx6q-tbs2910
gpio_fan
gpio_leds
Sort the pinctrl nodes alphabetically.
Signed-off-by: Soeren Moch <smoch@web.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Avoid the following warnings (example for usdhc2):
/soc/aips-bus@02100000/usdhc@02194000: voltage-ranges unspecified
sdhci-esdhc-imx 2194000.usdhc: could not get ultra high speed state,
work on normal mode
sdhci-esdhc-imx 2194000.usdhc: No vqmmc regulator found
Signed-off-by: Soeren Moch <smoch@web.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Configure SATA PHY transmit level, boost, attenuation and equalizer
parameters for long wire connections. TBS2910 contains a standard SATA
connector, so devices are typically connected with (longer) SATA cables.
And explicitly configuring these parameters avoids complaints about
"not specified" values in boot messages.
Signed-off-by: Soeren Moch <smoch@web.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Downstream packages like Debian flash-kernel use
/proc/device-tree/model
to determine which dtb file to install.
Hence each dts in the Linux kernel should provide a unique model
identifier.
Commit 8536239e371f ("ARM: dts: Restructure imx6qdl-wandboard.dtsi for new
rev C1 board.")' created new files imx6dl-wandboard-revb1.dts and
imx6q-wandboard-revb1.dts but used the same model identifier as in
imx6dl-wandboard.dts and imx6q-wandboard.dts.
This patch provides unique model identifiers for revision B1 of
the Wandboard Dual and Wandbaord Quad.
The patch leaves imx6dl-wandboard.dts and imx6q-wandboard.dts unchanged
because it is not foreseeable if the same dts will valid for future
board revisions or not. Furthermore we should avoid unnecessary
changes.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Uniwest evi is a portable electrical eddy current non-destructive
testing device.
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This patch adds dts file for imx6qp-sabresd board.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This patch adds basic dts file for i.MX6QP-Sbreauto board.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The i.MX6Quad Plus processor is an high performance SOC of i.MX6 family.
It has enhanced graphics performance and increased overall memory bandwidth
compared to i.MX6Q. Most of the design are same as i.MX6Quad/Dual, so code
for i.MX6Quad can be resued by this chip. The revision number is identied as
i.MX6Q Rev2.0, but actually it is a new chip, as we did many change to the
overall architecture.
This patch adds basic dtsi file support for the new i.MX6Quad Plus processor.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
GPLv2-only devicetrees make reuse difficult for software components
licensed under a different license.
The consensus is that a GPL/X11 dual-license should allow all necessary
uses, so relicense the vf610-twr.dts file to this combination.
CCs were acquired using (updated some email addresses, commented out
bouncing email addresses with --):
git shortlog -sne --no-merges arch/arm/boot/dts/vf610-twr.dts
--CC: Chao Fu <B44548@freescale.com>
CC: Cosmin Stoica <cosminstefan.stoica@freescale.com>
--CC: Fugang Duan <B38611@freescale.com>
--CC: Jingchang Lu <b35083@freescale.com>
--CC: Xiubo Li <Li.Xiubo@freescale.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Bill Pringlemeir <bpringle@sympatico.ca>
Acked-by: Cory Tusar <cory.tusar@pid1solutions.com>
Acked-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
GPLv2-only devicetrees make reuse difficult for software components
licensed under a different license.
The consensus is that a GPL/X11 dual-license should allow all necessary
uses, so relicense the vf*colibri* files to this combination.
CCs were acquired using:
git shortlog -sne --no-merges arch/arm/boot/dts/vf*colibri*
Acked-by: Cory Tusar <cory.tusar@pid1solutions.com>
Acked-by: Sanchayan Maity <maitysanchayan@gmail.com>
Acked-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
GPLv2-only devicetrees make reuse difficult for software components
licensed under a different license.
The consensus is that a GPL/X11 dual-license should allow all necessary
uses, so relicense the vfxxx.dtsi, vf500.dtsi and vf610.dtsi files to
this combination.
CCs were acquired using (updated some email addresses, commented out
bouncing email addresses with --):
git shortlog -sne --no-merges arch/arm/boot/dts/vf???.dtsi
--CC: Chao Fu <B44548@freescale.com>
CC: Cosmin Stoica <cosminstefan.stoica@freescale.com>
CC: Frank Li <Frank.Li@freescale.com>
CC: Fugang Duan <B38611@freescale.com>
--CC: Huang Shijie <b32955@freescale.com>
--CC: Jingchang Lu <jingchang.lu@freescale.com>
--CC: Xiubo Li <Li.Xiubo@freescale.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Cory Tusar <cory.tusar@pid1solutions.com>
Acked-by: Sanchayan Maity <maitysanchayan@gmail.com>
Acked-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Acked-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
LS1021a contains two PCIe controllers. The patch adds their node to
dts file.
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add sound support in UDOO board DT file.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add alias for FEC ethernet on Vybrid to allow bootloaders (like U-Boot)
patch-in the MAC address using this alias.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
PCIe reset signals are active low, and our GPIO for this is directly
connected to the PCIe reset. However, as the PCIe driver was not using
the flag, the specification of '0' flags (which means active high) had
not been noticed. Correct this oversight, and switch to using the
GPIO flag definitions instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Use proper gpio flag definitions for GPIOs rather than using opaque
uninformative numbers.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Avoid the following warning:
sdhci-esdhc-imx 2190000.usdhc: could not get ultra high speed state, work on normal mode
which occurs regularly at boot each time the SDHCI interface for the
Broadcom WiFi is probed at boot.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The reference clock for the SGTL5000 is generated by a 26MHz crystal
oscillator on the Ka-Ro electronics STK5 eval kits. Use the correct
frequency setting in DTB.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
ENET_OUT is used as reference clock for the ethernet PHY on the Ka-Ro
TX6 modules. Specify this clock in DTB to let it be managed correctly
by the driver.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The reference clock for the SGTL5000 is generated by a 26MHz crystal
oscillator on the Ka-Ro electronics STK5 eval kits. Use the correct
frequency setting in DTB.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The reference clock for the SGTL5000 is generated by a 26MHz crystal
oscillator on the Ka-Ro electronics STK5 eval kits. Use the correct
frequency setting in DTB.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This patch adds node i2c bus 3 to get the appropriate userland device
file. So for prototyping it's possible to experiment within userland.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Use pwm-backlight driver 'enable-gpios' property for backlight on/off
control.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
www.engicam.com/en/products/embedded/som/standard/i-core-rqs-m6s-dl-d-q
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The GW54xx can provide PWM4 out either the off-board backlight connector
or the off-board digital I/O connector. By default the pinmux routes it
to the backlight connector but this pinctl alternate provides documentation
for those who may want to change it.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Fix some invalid pwm pinmux configurations.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Since uboot v2016.01-rc2, which supported basic psci for i.mx7d.
So imx7d's second core can be enabled by psci.
Without arch timer, every timer event will be boardcasted to each core.
arch timer has local timer irq for each core.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Though the keyboard and other driver will continue to support the legacy
"gpio-key,wakeup", "linux,wakeup" and "enable-sdio-wakeup" boolean
property to enable the wakeup source, "wakeup-source" is the new
standard binding.
This patch replaces all the legacy wakeup properties with the unified
"wakeup-source" property in order to avoid any futher copy-paste
duplication.
Cc: Sascha Hauer <kernel@pengutronix.de>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This adds the remaining SAI instances SAI0, SAI1 and SAI3. All
instances are very similar, except that the DMA channel of SAI3
is available on MUX1 (compared to MUX0 for SAI0-SAI2). Also,
SAI3 has a slightly different memory map due to a deeper FIFO,
however in practice the current driver works for SAI3 fine.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add the necessary clock to use the KPP interface on i.MX6UL.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
remove whitespace before TAB.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Don't capitalize p in the pwm7 clock name.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
most of the clock tree structures on i.MX6 Quad Plus are
same as on i.MX6Q. there still some differences between
these two SOCs. compared to the i.XM6Q, the differents of
clocks on i.MX6QP is mainly on:
1. New clock gate added to support the PRE and PRG modules
2. 24MHz OSC clock option added to the UART, IPG, ECSPI, and
CAN clock roots.
3. MMDC channel 1 clock gate is now controllable.
4. clock gating added to the LDB_DIx_IPU clocks on i.MX6QP
5. EMI clock root divider fix
6. other updates fo CSCMRx, CSCDRx and CS2CDR registers.
detailed infomation, please refer to the i.MX6QP RM.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"The first real batch of fixes for this release cycle, so there are a
few more than usual.
Most of these are fixes and tweaks to board support (DT bugfixes,
etc). I've also picked up a couple of small cleanups that seemed
innocent enough that there was little reason to wait (const/
__initconst and Kconfig deps).
Quite a bit of the changes on OMAP were due to fixes to no longer
write to rodata from assembly when ARM_KERNMEM_PERMS was enabled, but
there were also other fixes.
Kirkwood had a bunch of gpio fixes for some boards. OMAP had RTC
fixes on OMAP5, and Nomadik had changes to MMC parameters in DT.
All in all, mostly the usual mix of various fixes"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (46 commits)
ARM: multi_v7_defconfig: enable DW_WATCHDOG
ARM: nomadik: fix up SD/MMC DT settings
ARM64: tegra: Add chosen node for tegra132 norrin
ARM: realview: use "depends on" instead of "if" after prompt
ARM: tango: use "depends on" instead of "if" after prompt
ARM: tango: use const and __initconst for smp_operations
ARM: realview: use const and __initconst for smp_operations
bus: uniphier-system-bus: revive tristate prompt
arm64: dts: Add missing DMA Abort interrupt to Juno
bus: vexpress-config: Add missing of_node_put
ARM: dts: am57xx: sbc-am57x: correct Eth PHY settings
ARM: dts: am57xx: cl-som-am57x: fix CPSW EMAC pinmux
ARM: dts: am57xx: sbc-am57x: fix UART3 pinmux
ARM: dts: am57xx: cl-som-am57x: update SPI Flash frequency
ARM: dts: am57xx: cl-som-am57x: set HOST mode for USB2
ARM: dts: am57xx: sbc-am57x: fix SB-SOM EEPROM I2C address
ARM: dts: LogicPD Torpedo: Revert Duplicative Entries
ARM: dts: am437x: pixcir_tangoc: use correct flags for irq types
ARM: dts: am4372: fix irq type for arm twd and global timer
ARM: dts: at91: sama5d4 xplained: fix phy0 IRQ type
...
|
|
git://git.linaro.org/landing-teams/working/fujitsu/integration
Pull mailbox fixes from Jassi Brar:
- fix getting element from the pcc-channels array by simply indexing
into it
- prevent building mailbox-test driver for archs that don't have IOMEM
* 'mailbox-devel' of git://git.linaro.org/landing-teams/working/fujitsu/integration:
mailbox: Fix dependencies for !HAS_IOMEM archs
mailbox: pcc: fix channel calculation in get_pcc_channel()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some USB fixes for 4.5-rc3.
The usual, xhci fixes for reported issues, combined with some small
gadget driver fixes, and a MAINTAINERS file update. All have been in
linux-next with no reported issues"
* tag 'usb-4.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
xhci: harden xhci_find_next_ext_cap against device removal
xhci: Fix list corruption in urb dequeue at host removal
usb: host: xhci-plat: fix NULL pointer in probe for device tree case
usb: xhci-mtk: fix AHB bus hang up caused by roothubs polling
usb: xhci-mtk: fix bpkts value of LS/HS periodic eps not behind TT
usb: xhci: apply XHCI_PME_STUCK_QUIRK to Intel Broxton-M platforms
usb: xhci: set SSIC port unused only if xhci_suspend succeeds
usb: xhci: add a quirk bit for ssic port unused
usb: xhci: handle both SSIC ports in PME stuck quirk
usb: dwc3: gadget: set the OTG flag in dwc3 gadget driver.
Revert "xhci: don't finish a TD if we get a short-transfer event mid TD"
MAINTAINERS: fix my email address
usb: dwc2: Fix probe problem on bcm2835
Revert "usb: dwc2: Move reset into dwc2_get_hwparams()"
usb: musb: ux500: Fix NULL pointer dereference at system PM
usb: phy: mxs: declare variable with initialized value
usb: phy: msm: fix error handling in probe.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO driver fixes from Greg KH:
"Here are some IIO and staging driver fixes for 4.5-rc3.
All of them, except one, are for IIO drivers, and one is for a speakup
driver fix caused by some earlier patches, to resolve a reported build
failure"
* tag 'staging-4.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
Staging: speakup: Fix allyesconfig build on mn10300
iio: dht11: Use boottime
iio: ade7753: avoid uninitialized data
iio: pressure: mpl115: fix temperature offset sign
iio: imu: Fix dependencies for !HAS_IOMEM archs
staging: iio: Fix dependencies for !HAS_IOMEM archs
iio: adc: Fix dependencies for !HAS_IOMEM archs
iio: inkern: fix a NULL dereference on error
iio:adc:ti_am335x_adc Fix buffered mode by identifying as software buffer.
iio: light: acpi-als: Report data as processed
iio: dac: mcp4725: set iio name property in sysfs
iio: add HAS_IOMEM dependency to VF610_ADC
iio: add IIO_TRIGGER dependency to STK8BA50
iio: proximity: lidar: correct return value
iio-light: Use a signed return type for ltr501_match_samp_freq()
|
