| Age | Commit message (Collapse) | Author |
|---|
|
In the commit referenced below I failed to pay attention to this code
also being buildable as 32-bit. Adjust the type of "ret" - there's no
real need for it to be wider than 32 bits.
Fixes: 934ef33ee75c ("x86/PVH: obtain VGA console info in Dom0")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/2d2193ff-670b-0a27-e12d-2c5c4c121c79@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
The hvc machinery registers both a console and a tty device based on
the hv ops provided by the specific implementation. Those two
interfaces however have different locks, and there's no single locks
that's shared between the tty and the console implementations, hence
the driver needs to protect itself against concurrent accesses.
Otherwise concurrent calls using the split interfaces are likely to
corrupt the ring indexes, leaving the console unusable.
Introduce a lock to xencons_info to serialize accesses to the shared
ring. This is only required when using the shared memory console,
concurrent accesses to the hypercall based console implementation are
not an issue.
Note the conditional logic in domU_read_console() is slightly modified
so the notify_daemon() call can be done outside of the locked region:
it's an hypercall and there's no need for it to be done with the lock
held.
Fixes: b536b4b96230 ('xen: use the hvc console infrastructure for Xen console')
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20221130150919.13935-1-roger.pau@citrix.com
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
Local port is a 10-bit number, but it was mistakenly stored in a u8,
resulting in firmware errors when using a netdev corresponding to a
local port higher than 255.
Fix by storing the local port in u16, as is done in the rest of the
code.
Fixes: bf73904f5fba ("mlxsw: Add support for 802.1Q FID family")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/eace1f9d96545ab8a2775db857cb7e291a9b166b.1679398549.git.petrm@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The bob supply is used by several pmic regulators and components which
are not (yet fully) described in the devicetree.
Mark the regulator as always-on for now.
Fixes: f29077d86652 ("arm64: dts: qcom: sc8280xp-x13s: Add soundcard support")
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230322113318.17908-5-johan+linaro@kernel.org
|
|
The s12b supply is used by several pmic regulators as well as the
wlan/bluetooth radio which are not yet fully described in the
devicetree.
Mark the regulator as always-on for now.
Fixes: f29077d86652 ("arm64: dts: qcom: sc8280xp-x13s: Add soundcard support")
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230322113318.17908-4-johan+linaro@kernel.org
|
|
The s10b supply is used by several components that are not (yet)
described in devicetree (e.g. ram, charger, ec) and must not be
disabled.
Mark the regulator as always-on.
Fixes: f29077d86652 ("arm64: dts: qcom: sc8280xp-x13s: Add soundcard support")
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230322113318.17908-3-johan+linaro@kernel.org
|
|
The s11b supply is used by the wlan module (as well as some of the
pmics) which are not yet fully described in the devicetree.
Mark the regulator as always-on for now.
Fixes: 123b30a75623 ("arm64: dts: qcom: sc8280xp-x13s: enable WiFi controller")
Cc: stable@vger.kernel.org # 6.2
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230322113318.17908-2-johan+linaro@kernel.org
|
|
When a cpufreq policy appears or goes away, the CPU cooling devices for
the CPUs covered by that policy need to be updated so that the new
processor_get_max_state() value is stored as max_state and the
statistics in sysfs are rearranged for each of them.
Do that accordingly in acpi_thermal_cpufreq_init() and
acpi_thermal_cpufreq_exit().
Fixes: a365105c685c("thermal: sysfs: Reuse cdev->max_state")
Reported-by: Wang, Quanxian <quanxian.wang@intel.com>
Link: https://lore.kernel.org/linux-pm/53ec1f06f61c984100868926f282647e57ecfb2d.camel@intel.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Zhang Rui <rui.zhang@intel.com>
|
|
Introduce a core thermal API function, thermal_cooling_device_update(),
for updating the max_state value for a cooling device and rearranging
its statistics in sysfs after a possible change of its ->get_max_state()
callback return value.
That callback is now invoked only once, during cooling device
registration, to populate the max_state field in the cooling device
object, so if its return value changes, it needs to be invoked again
and the new return value needs to be stored as max_state. Moreover,
the statistics presented in sysfs need to be rearranged in general,
because there may not be enough room in them to store data for all
of the possible states (in the case when max_state grows).
The new function takes care of that (and some other minor things
related to it), but some extra locking and lockdep annotations are
added in several places too to protect against crashes in the cases
when the statistics are not present or when a stale max_state value
might be used by sysfs attributes.
Note that the actual user of the new function will be added separately.
Link: https://lore.kernel.org/linux-pm/53ec1f06f61c984100868926f282647e57ecfb2d.camel@intel.com/
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Zhang Rui <rui.zhang@intel.com>
|
|
Introduce a helper function, thermal_cooling_device_present(), for
checking if the given cooling device is in the list of registered
cooling devices to avoid some code duplication in a subsequent
patch.
No expected functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Zhang Rui <rui.zhang@intel.com>
|
|
The cpufreq policy notifier in the ACPI processor driver may as
well be registered before the driver itself, which causes
acpi_processor_cpufreq_init to be true (unless the notifier
registration fails, which is unlikely at that point) when the
ACPI CPU thermal cooling devices are registered, so the
processor_get_max_state() result does not change while
acpi_processor_driver_init() is running.
Change the ordering in acpi_processor_driver_init() accordingly
to prevent the max_state value from remaining 0 permanently for all
ACPI CPU cooling devices due to setting acpi_processor_cpufreq_init
too late. [Note that processor_get_max_state() may still return
different values at different times after this change, depending on
the cpufreq driver registration time, but that issue needs to be
addressed separately.]
Fixes: a365105c685c("thermal: sysfs: Reuse cdev->max_state")
Reported-by: Wang, Quanxian <quanxian.wang@intel.com>
Link: https://lore.kernel.org/linux-pm/53ec1f06f61c984100868926f282647e57ecfb2d.camel@intel.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Zhang Rui <rui.zhang@intel.com>
|
|
Change no bootconfig data error message if user do not specify 'bootconfig'
option but CONFIG_BOOT_CONFIG_FORCE=y.
With CONFIG_BOOT_CONFIG_FORCE=y, the kernel proceeds bootconfig check even
if user does not specify 'bootconfig' option. So the current error message
is confusing. Let's show just an information message to notice skipping
the bootconfig in that case.
Link: https://lore.kernel.org/all/167754610254.318944.16848412476667893329.stgit@devnote2/
Fixes: b743852ccc1d ("Allow forcing unconditional bootconfig processing")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/all/CAMuHMdV9jJvE2y8gY5V_CxidUikCf5515QMZHzTA3rRGEOj6=w@mail.gmail.com/
Suggested-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Tested-by: Paul E. McKenney <paulmck@kernel.org>
Acked-by: Mukesh Ojha <quic_mojha@quicinc.com>
|
|
If a packet has reached its intended destination, it was bumped to the code
that accepts it, without first checking if a mesh_path needs to be created
based on the discovered source.
Fix this by moving the destination address check further down.
Cc: stable@vger.kernel.org
Fixes: 986e43b19ae9 ("wifi: mac80211: fix receiving A-MSDU frames on mesh interfaces")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20230314095956.62085-3-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When ieee80211_select_queue is called for mesh, the sta pointer is usually
NULL, since the nexthop is looked up much later in the tx path.
Explicitly check for unicast address in that case in order to make qos work
again.
Cc: stable@vger.kernel.org
Fixes: 50e2ab392919 ("wifi: mac80211: fix queue selection for mesh/OCB interfaces")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20230314095956.62085-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Rename symbols to match the style of other fbdev-emulation source
code. No functional changes.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Zack Rusin <zackr@vmware.com>
Tested-by: Sui Jingfeng <suijingfeng@loongson.cn>
Link: https://patchwork.freedesktop.org/patch/msgid/20230320150751.20399-9-tzimmermann@suse.de
|
|
Consolidate all handling of CONFIG_DRM_FBDEV_LEAK_PHYS_SMEM by
making the module parameter optional in drm_fb_helper.c.
Without the config option, modules can set smem_start in struct
fb_info for internal usage, but not export if to userspace. The
address can only be exported by enabling the option and setting
the module parameter. Also update the comment.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Zack Rusin <zackr@vmware.com>
Tested-by: Sui Jingfeng<suijingfeng@loongson.cn>
Link: https://patchwork.freedesktop.org/patch/msgid/20230320150751.20399-8-tzimmermann@suse.de
|
|
Clean up fbdev and client state if the probe function fails. It
used to leak allocated resources. Also reorder the individual steps
to simplify cleanup.
v2:
* move screen_size update into separate patches
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Zack Rusin <zackr@vmware.com>
Tested-by: Sui Jingfeng <suijingfeng@loongson.cn>
Link: https://patchwork.freedesktop.org/patch/msgid/20230320150751.20399-7-tzimmermann@suse.de
|
|
The size of the screen memory should be equivalent to the size of
the screen's GEM buffer. Don't recalculate the value.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Sui Jingfeng <suijingfeng@loongson.cn>
Link: https://patchwork.freedesktop.org/patch/msgid/20230320150751.20399-6-tzimmermann@suse.de
|
|
The size of the framebuffer can either be stored in screen_info or
smem_len. Take both into account in the deferred I/O code.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Sui Jingfeng <suijingfeng@loongson.cn>
Link: https://patchwork.freedesktop.org/patch/msgid/20230320150751.20399-5-tzimmermann@suse.de
|
|
Export the fb_info release code as drm_fb_helper_release_info(). Will
help with cleaning up failed fbdev probing.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Zack Rusin <zackr@vmware.com>
Tested-by: Sui Jingfeng<suijingfeng@loongson.cn>
Link: https://patchwork.freedesktop.org/patch/msgid/20230320150751.20399-4-tzimmermann@suse.de
|
|
Remove the flag prefer_shadow_fbdev from struct drm_mode_config.
Drivers set this flag to enable shadow buffering in the generic
fbdev emulation. Such shadow buffering is now mandatory, so the
flag is unused.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Zack Rusin <zackr@vmware.com>
Tested-by: Sui Jingfeng <suijingfeng@loongson.cn>
Link: https://patchwork.freedesktop.org/patch/msgid/20230320150751.20399-3-tzimmermann@suse.de
|
|
Remove all codepaths that implement fbdev output directly on GEM
buffers. Always allocate a shadow buffer in system memory and set
up deferred I/O for mmap.
The fbdev code that operated directly on GEM buffers was used by
drivers based on GEM DMA helpers. Those drivers have been migrated
to use fbdev-dma, a dedicated fbdev emulation for DMA memory. All
remaining users of fbdev-generic require shadow buffering.
Memory management of the remaining callers uses TTM, GEM SHMEM
helpers or a variant of GEM DMA helpers that is incompatible with
fbdev-dma. Therefore remove the unused codepaths from fbdev-generic
and simplify the code.
Using a shadow buffer with deferred I/O is probably the best case
for most remaining callers. Some of the TTM-based drivers might
benefit from a dedicated fbdev emulation that operates directly on
the driver's video memory.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Zack Rusin <zackr@vmware.com>
Tested-by: Sui Jingfeng <suijingfeng@loongson.cn>
Link: https://patchwork.freedesktop.org/patch/msgid/20230320150751.20399-2-tzimmermann@suse.de
|
|
Some recent upstream debugging uncovered the fact that in
iwlwifi, the TXQ list manipulation is racy.
Introduce a new state bit for when the TXQ is completely
ready and can be used without locking, and if that's not
set yet acquire the lock to check everything correctly.
Reviewed-by: Benjamin Berg <benjamin.berg@intel.com>
Tested-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This could race if the queue is redirected while full, then
the flushing internally would start it while it's not yet
usable again. Fix it by using two state bits instead of just
one.
Reviewed-by: Benjamin Berg <benjamin.berg@intel.com>
Tested-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
sh/migor_defconfig:
mm/slab.c: In function ‘slab_memory_callback’:
mm/slab.c:1127:23: error: implicit declaration of function ‘init_cache_node_node’; did you mean ‘drain_cache_node_node’? [-Werror=implicit-function-declaration]
1127 | ret = init_cache_node_node(nid);
| ^~~~~~~~~~~~~~~~~~~~
| drain_cache_node_node
The #ifdef condition protecting the definition of init_cache_node_node()
no longer matches the conditions protecting the (multiple) users.
Fix this by syncing the conditions.
Fixes: 76af6a054da40553 ("mm/migrate: add CPU hotplug to demotion #ifdef")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/b5bdea22-ed2f-3187-6efe-0c72330270a4@infradead.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
|
|
Replace the open-code with dev_err_probe() to simplify the code.
Signed-off-by: Ye Xingchen <ye.xingchen@zte.com.cn>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/202303221622511915615@zte.com.cn
|
|
Replace the open-code with dev_err_probe() to simplify the code.
Signed-off-by: Ye Xingchen <ye.xingchen@zte.com.cn>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/202303221621336645576@zte.com.cn
|
|
Not used by any drivers any more, the only use case in drm_dev_init()
can be inlined now.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316082035.567520-2-christian.koenig@amd.com
|
|
The FEI field of C2HTermReq/H2CTermReq is 4 bytes but not 4-byte-aligned
in the NVMe/TCP specification (it is located at offset 10 in the PDU).
Split it into two 16-bit integers in struct nvme_tcp_term_pdu
so no padding is inserted. There should also be 10 reserved bytes after.
There are currently no users of this type.
Fixes: fc221d05447aa6db ("nvme-tcp: Add protocol header")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Caleb Sander <csander@purestorage.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Identify CNS 06h (I/O Command Set Specific Identify Controller data
structure) is supported only on i/o controllers.
But nvme_init_non_mdts_limits() currently invokes this on all
controllers. Correct this by ensuring this is sent to I/O
controllers only.
Signed-off-by: Martin George <marting@netapp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Limit one queue per gang in mes self test,
due to mes schq fw change.
Signed-off-by: Jack Xiao <Jack.Xiao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
May help stability with some navi1x boards.
Hopefully this helps with stability with multiple monitors
and would allow us to re-enable MPC_SPLIT_DYNAMIC in the
DC code for better power savings.
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2196
Reviewed-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
|
|
This DC version brings along:
- Power down eDP if eDP not present
- Set MPC_SPLIT_DYNAMIC for DCN10 and DCN301
- Initialize link_srv in virtual env
- Code cleanup and alignment
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why & How]
seamless_odm set was not picked up while
merging commit 2d017189e2b3 ("drm/amd/display:
Blank eDP on enable drv if odm enabled")
Fixes: 2d017189e2b3 ("drm/amd/display: Blank eDP on enable drv if odm enabled")
Reviewed-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why & How]
When merging commit 9af611f29034
("drm/amd/display: Fix DCN32 DPSTREAMCLK_CNTL programming"),
index change was not picked up.
Cc: stable@vger.kernel.org
Cc: Mario Limonciello <mario.limonciello@amd.com>
Fixes: 9af611f29034 ("drm/amd/display: Fix DCN32 DPSTREAMCLK_CNTL programming")
Reviewed-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why & How]
Due to historic issues, commit_planes_for_stream() has grown differently
compared to latest dc code. Apply missed changes to make it aligned.
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This reverts commit bcfab8e35ce81e2fd3230c1575024bfde0d28c8b.
Hopefully this is fixed by the previous patch to enable
TEMP_DEPENDENT_VMIN for navi1x or otherwise and we can re-enable
MPC_SPLIT_DYNAMIC for DCN 2.0 for better power savings.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
|
|
Since DC version 3.2.226, DC started to use a new internal commit
sequence that better deals with hardware limitations. Usually, DC adopts
split pipe dynamics to improve the display bandwidth and, in some cases,
to save power. This commit sets MPC_SPLIT_DYNAMIC for DCN301, improving
the bandwidth and fixing the cursor bug on KDE when it tries hardware
rotation.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/2247
Cc: Melissa Wen <mwen@igalia.com>
Cc: Xaver Hugl <xaver.hugl@gmail.com>
Reviewed-by: Melissa Wen <mwen@igalia.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Since DC version 3.2.226, DC started to use a new internal commit
sequence that better deals with multiple hardware constraints. One of
the improvements is a more reliable sequence for pipe split. Due to the
transition made in version 3.2.226, it should be more reliable to use
the pipe policy as MPC_SPLIT_DYNAMIC, and this commit makes this change.
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
missing change when port to these two dcn version.
Reviewed-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Leo Ma <hanghong.ma@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why & How]
- Add CRC for test support
- Add params to allow control into to DMUB.
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
In order to follow the new protocol of calling link functions
[HOW]
Add the function pointer to the link_srv
Reviewed-by: Kshitij Bhardwaj <kshitij.bhardwaj1@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Mustapha Ghaddar <mghaddar@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
when refactoring to link_srv, we did not include the
virtual environment case where dc_construct_ctx gets
called instead of dc_construct
[how]
add initialize link_srv to dc_construct_ctx as well
Reviewed-by: Leo Ma <hanghong.ma@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Martin Leung <Martin.Leung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
When init, driver will power up eDP to check eDP
present or not. If eDP not present, driver doesn't
power off eDP VDD cause power consumption.
[How]
If eDP is not present when detection, power off eDP
VDD.
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Paul Hsieh <Paul.Hsieh@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
Processing rate of the DP encoder, must be programmed to be the same as
DIG_FIFO_OUTPUT_ PROCESSING_MODE in DP mode
0: 1 pixel per cycle
1: 2 pixel per cycle
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
There is no need to wait vblank in the vupdate locked
region at a full type update
[HOW]
skip wait vblank when global sync change
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Zhikai Zhai <zhikai.zhai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
When calling the dc_link_bw_kbps_from_raw_frl_link_rate_data from
amdgpu_dm, GCC highlighted the following issue:
In function ‘get_conv_frl_bw’:
error: passing argument 1 of
‘dc_link_bw_kbps_from_raw_frl_link_rate_data’ discards ‘const’ qualifier
from pointer target type [-Werror=discarded-qualifiers]
997 | aconnector->dc_link->dc,
This commit fix this issue by making DC a constant variable since we
only use it to invoke the function
bw_kbps_from_raw_frl_link_rate_data().
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why & How]
Make DCN32 3dlut function non-static and thus
available for future DCNs.
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Gfx v11_0_3 supports ras on SRIOV, so need to resume ras
during reset.
Signed-off-by: YiPeng Chai <YiPeng.Chai@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Reinit mes ip block during reset on SRIOV.
Signed-off-by: YiPeng Chai <YiPeng.Chai@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
