| Age | Commit message (Collapse) | Author |
|---|
|
Abort all jobs that belong to contexts generating MMU faults in order
to avoid flooding host with MMU IRQs.
Jobs are cancelled with:
- SSID_RELEASE command when OS scheduling is enabled
- DESTROY_CMDQ command when HW scheduling is enabled
Signed-off-by: Maciej Falkowski <maciej.falkowski@intel.com>
Co-developed-by: Wachowski, Karol <karol.wachowski@intel.com>
Signed-off-by: Wachowski, Karol <karol.wachowski@intel.com>
Reviewed-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240611120433.1012423-3-jacek.lawrynowicz@linux.intel.com
|
|
Send workpoint 0 request during power up on 37xx.
This is needed in rare case where WP0 was not sent
during power down due to device hang.
Signed-off-by: Wachowski, Karol <karol.wachowski@intel.com>
Reviewed-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240611120433.1012423-2-jacek.lawrynowicz@linux.intel.com
|
|
Add a connector debugfs entry showing if link retraining is disabled.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-22-imre.deak@intel.com
|
|
Add a connector debugfs entry to force retrain an active link. This can
be used to test both custom link parameters (previously forced via the
force_link_rate/lane_count entries) or link train failure scenarios
(previously forced via the force_link_training_failure entry). The entry
will autoreset after the link-retrain is complete.
v2: Add the entry from intel_dp_link_training.c (Jani)
v3: Lock connection_mutex only for the required intel_dp state. (Ville)
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-21-imre.deak@intel.com
|
|
Add a connector debugfs entry to force a failure during the following
1-2 link training. The entry will auto-reset after the specified link
training events are complete.
v2: Add the entry from intel_dp_link_training.c (Jani)
v3: Lock connection_mutex only for the required intel_dp state. (Ville)
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-20-imre.deak@intel.com
|
|
Add connector debugfs entries to get the maximum link rate and lane
count.
v2: Lock connection_mutex only for the required intel_dp state. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-19-imre.deak@intel.com
|
|
Add connector debugfs entries to force the link rate/lane count to be
used by a link training afterwards. These settings will be clamped to
the supported, i.e. the source's and sink's common rate/lane count.
After forcing the link rate/lane count reset the link training
parameters and for a non-auto setting disable reducing the link
parameters via the fallback logic. The former one can be used after
testing link training failure scenarios - via debugfs entries added
later - to reset the reduced link parameters after the test.
v2:
- Add the entries from intel_dp_link_training.c (Jani)
- Rename the entries to i915_dp_set_link_rate/lane_count.
v3: (Ville)
- Rename the entries/struct fields to force_link_rate/lane_count.
- Lock connection_mutex only for the required intel_dp state.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-18-imre.deak@intel.com
|
|
Reduce the link parameters after a link training failure for MST
outputs, similarly to how this is done for SST.
For now allow the reduction only by staying in the 8b/10b vs. 128b/132b
mode. Enabling the mode switch is left for a follow-up patchset, after
taking measures ensuring that the mode switch happens properly. In
particular a rediscovery of the whole MST topology may be required for
such a switch, see the References below.
Link: https://gitlab.freedesktop.org/drm/i915/kernel/-/issues/10970
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-17-imre.deak@intel.com
|
|
Reset the flag indicating an active link after disabling an MST link,
similarly to how this is done for SST outputs. This avoids trying to
retrain an MST link while its disabled.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-16-imre.deak@intel.com
|
|
After a link training failure if the link parameters can't be further
reduced, there is no point in trying to retrain the link in the driver.
This avoids excessive retrain attempts after detecting a bad link, for
instance while handling MST HPD IRQs, which is likely redundant as the
link training failed already twice with the same minimum link
parameters. Userspace can still try to retrain the link with these
parameters via a modeset.
While at it make the error message more accurate.
v2: Move converting the error to a debug message to the relevant
follow-up patch. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-15-imre.deak@intel.com
|
|
Simplify things by retraining a DP link if a bad link is detected in the
HPD IRQ handler from the encoder's check link state work, similarly to
how this is done after a modeset link training failure.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-14-imre.deak@intel.com
|
|
Simplify things by retraining a DP link if a bad link is detected in the
connector detect handler from the encoder's check link state work,
similarly to how this is done after a modeset link training failure.
v2: Add TODO: comment to remove the detect-time link state check.
(Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-13-imre.deak@intel.com
|
|
Simplify things by retraining a DP link if a bad link is detected in the
hotplug handler from the encoder's check link state work, similarly to
how this is done after a modeset link training failure.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-12-imre.deak@intel.com
|
|
Send a modeset-retry uevent to all connectors in the same MST topology
after a link training failure and reduction of the link parameters. This
matches the way the same uevent is sent after a DP tunnel BW allocation
failure.
v2: Add NOTE that the atomic state may not be valid for SST links and
assert that it's valid for MST links. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-11-imre.deak@intel.com
|
|
The next patch adds sending a modeset-retry uevent after a link training
failure to all MST connectors on link. This requires the atomic state,
so pass it to intel_dp_start_link_train(). In case of SST where
retraining still happens by calling this function directly instead of a
modeset commit the atomic state is not available and NULL is passed
instead. This is ok, since in this case the encoder's only DP connector
is available from intel_dp->attached_connector not requiring the atomic
state.
v2: Add NOTE that the atomic state may not be valid for SST links and
assert that it's valid for MST links. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-10-imre.deak@intel.com
|
|
Try to maintain the current link parameters by retrying the link
training with unchanged link parameters before reducing these parameters
(sending an uevent to userspace to retrain the link instead).
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-9-imre.deak@intel.com
|
|
Recheck the link state after a passing link training, with a 2 sec delay
to account for cases where the link goes bad following the link training
and the sink doesn't report this via an HPD IRQ.
The delayed work added here will be also used by a later patch after a
failed link training to try to retrain the link with unchanged link
params before reducing the link params.
v2: Don't flush an uninitialized delayed work (on HDMI-only DDI ports).
v3:
- Move the helpers to a new intel_encoder.c file, rename them
accordingly. (Ville)
- Add the work to intel_encoder instead of intel_digital_port.
- Call the encoder specific link check function via an encoder hook.
- Flush the link check work during encoder destroy from
intel_dp_encoder_flush_work().
- Flush the link check work during encoder suspend as well.
v4: Call intel_encoder_link_check_init() with a valid encoder pointer.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610181428.2955658-1-imre.deak@intel.com
|
|
Instead of direct calls to the link train functions, retrain the link
via a commit modeset. The direct call means that the output port will be
disabled/re-enabled while the rest of the pipeline (transcoder) is
active, which doesn't seem to work on MST at least. It leads to
underruns and black screen, presumedly because the transcoder is not
disabled/re-enabled along the port.
Leave switching to a commit modeset on SST for a later patchset, as that
seems to work ok currently (though better to using a commit there too,
due to the suppressed underruns).
v2: Keep reverse line length order for local variables. (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-7-imre.deak@intel.com
|
|
Factor out a function to modeset commit a set of pipes, which a later
patch will reuse for DP link retraining.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-6-imre.deak@intel.com
|
|
Reduce the indentation in intel_dp_get_link_train_fallback_values() by
adding separate helpers to reduce the link rate and lane count. Also
simplify things by passing crtc_state to the function.
This also prepares for later patches in the patchset adding a limitation
on how the link params are reduced.
While at it use lt_dbg()/lt_err() for debug/error prints in the function
which will also print the connector/encoder prefix and add a debug print
about reducing the link parameters.
v2:
- Align reduce_lane_count()'s error handling flow with
reduce_link_rate(). (Ville, Jani)
- Use lt_dbg()/lt_err() in the function.
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-5-imre.deak@intel.com
|
|
Move the functions used to reduce the link parameters during link
training to intel_dp_link_training.c .
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Manasi Navare <navaremanasi@chromium.org>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-4-imre.deak@intel.com
|
|
For clarity move the link training parameters updated during link
training based on the pass/fail LT result under a substruct in intel_dp.
This prepares for later patches in this patchset adding similar params
here. Rename intel_dp_reset_max_link_params() to
intel_dp_reset_link_params() to better reflect what state gets reset.
v2: Add the parameters to a more generic link substruct. (Jani)
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-3-imre.deak@intel.com
|
|
Symbols consisting of multiple (4) TU timeslots may get split across
MTPs when using 2 or 1 link lanes. Avoid this, as required by Bspec by
aligning the allocated TUs to 2 when using 2 lanes and 4 when using 1
lane.
Atm, we also have to align the PBNs used to allocate BW along the MST
path, since DRM core keeps track of its own TU value, derived from the
PBN and that TU value must match what the driver calculates.
On some platforms the alignment is only required on 8b/10b links, a
follow-up patch will remove the limitation for those.
Bspec: 49266, 68922
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-2-imre.deak@intel.com
|
|
Check the pixel clock for the mode in atomic_check and ensure that
it is within the range supported by the bridge.
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240613083805.439337-4-j-choudhary@ti.com
Signed-off-by: Maxime Ripard <mripard@kernel.org>
|
|
Change exisitig enable() and disable() bridge hooks to their atomic
counterparts as the former hooks are deprecated.
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240613083805.439337-3-j-choudhary@ti.com
Signed-off-by: Maxime Ripard <mripard@kernel.org>
|
|
Currently, mode_valid is defined only in drm_connector_helper_funcs.
When the bridge is attached with the 'DRM_BRIDGE_ATTACH_NO_CONNECTOR'
flag, the connector is not initialized, and so is the mode_valid
hook under connector helper funcs.
It also returns MODE_OK for all modes without actually checking the
modes.
So move the mode_valid hook to drm_bridge_funcs with proper clock
checks for maximum and minimum pixel clock supported by the bridge.
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Sui Jingfeng <sui.jingfeng@linux.dev>
Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240613083805.439337-2-j-choudhary@ti.com
Signed-off-by: Maxime Ripard <mripard@kernel.org>
|
|
The branch or sink device decompressing a stream may have a limitation
on the input/uncompressed BPP, which is lower than the base line BPP
(determined by the sink's EDID). In some cases a stream with an input
BPP higher than this limit will be converted automatically by the device
decompressing the stream, by truncating the BPP, however in some cases
- seen at least in Dell dock's DP->HDMI converters - the decompression
will fail.
Fix the above by limiting the input BPP correctly. This is done already
correctly for SST outputs.
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240611153351.3013235-1-imre.deak@intel.com
|
|
It looks like the documentation for the HDMI-related fields recently
added to both the drm_connector and drm_connector_state structures
trigger some warnings because of their use of anonymous structures:
$ scripts/kernel-doc -none include/drm/drm_connector.h
include/drm/drm_connector.h:1138: warning: Excess struct member 'broadcast_rgb' description in 'drm_connector_state'
include/drm/drm_connector.h:1138: warning: Excess struct member 'infoframes' description in 'drm_connector_state'
include/drm/drm_connector.h:1138: warning: Excess struct member 'avi' description in 'drm_connector_state'
include/drm/drm_connector.h:1138: warning: Excess struct member 'hdr_drm' description in 'drm_connector_state'
include/drm/drm_connector.h:1138: warning: Excess struct member 'spd' description in 'drm_connector_state'
include/drm/drm_connector.h:1138: warning: Excess struct member 'vendor' description in 'drm_connector_state'
include/drm/drm_connector.h:1138: warning: Excess struct member 'is_limited_range' description in 'drm_connector_state'
include/drm/drm_connector.h:1138: warning: Excess struct member 'output_bpc' description in 'drm_connector_state'
include/drm/drm_connector.h:1138: warning: Excess struct member 'output_format' description in 'drm_connector_state'
include/drm/drm_connector.h:1138: warning: Excess struct member 'tmds_char_rate' description in 'drm_connector_state'
include/drm/drm_connector.h:2112: warning: Excess struct member 'vendor' description in 'drm_connector'
include/drm/drm_connector.h:2112: warning: Excess struct member 'product' description in 'drm_connector'
include/drm/drm_connector.h:2112: warning: Excess struct member 'supported_formats' description in 'drm_connector'
include/drm/drm_connector.h:2112: warning: Excess struct member 'infoframes' description in 'drm_connector'
include/drm/drm_connector.h:2112: warning: Excess struct member 'lock' description in 'drm_connector'
include/drm/drm_connector.h:2112: warning: Excess struct member 'audio' description in 'drm_connector'
Create some intermediate structures instead of anonymous ones to silence
the warnings.
Reported-by: Jani Nikula <jani.nikula@linux.intel.com>
Suggested-by: Jani Nikula <jani.nikula@linux.intel.com>
Fixes: 54cb39e2293b ("drm/connector: hdmi: Create an HDMI sub-state")
Fixes: 948f01d5e559 ("drm/connector: hdmi: Add support for output format")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610111200.428224-1-mripard@kernel.org
|
|
Set .detect_ctx() in struct drm_connector_helper_funcs to the
common helper drm_connector_helper_detect_from_ddc() and enable
polling for the connector. Mgag200 will now test for the monitor's
presence by probing the DDC in regular intervals.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610141141.29527-4-tzimmermann@suse.de
|
|
The BMC output can be viewed via the BMC's web interface or a
similar client. Represent it as virtual encoder and connector.
It's attached to the same CRTC as the VGA connector.
The connector's status depends on the physical connector's status.
The BMC is only connected if the physical connector is not. This
is necessary to support userspace clients that can only handle a
single output per CRTC.
The BMC is a server feature. Add a BMC output for all server chips,
but not the desktop models.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610141141.29527-3-tzimmermann@suse.de
|
|
The various models have common code for the VGA output's encoder and
connector. Move everything into a single shared source file. Remove some
obsolete initializer macros. No functional changes.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610141141.29527-2-tzimmermann@suse.de
|
|
Compute trans vrr vsync params only when either VRR or CMRR
is enabled.
Fixes: 5922f45329cd ("drm/i915/display: Compute vrr vsync params")
Cc: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Cc: Suraj Kandpal <suraj.kandpal@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240611120525.148042-1-mitulkumar.ajitkumar.golani@intel.com
|
|
According to BSpec we now should call "master" pipes, "primary" pipes
and "slave" pipes, should be "secondary" pipes.
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
[vsyrjala: Don't rename port sync stuff, catch a few more things]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240603112551.6481-3-stanislav.lisovskiy@intel.com
|
|
Lets unify both bigjoiner and ultrajoiner under simple "joiner" name,
because in future we might have multiple configurations, involving
multiple bigjoiners, ultrajoiner, however it is possible to use
same api for handling both.
v2: - Renamed back some bigjoiner specific parts for now(Ville)
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
[vsyrjala: Catch a few more cases]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240607075457.15700-1-stanislav.lisovskiy@intel.com
|
|
mipi_dsi_msleep should be modified to accept ctx as a pointer and the
function call should be adjusted accordingly.
Fixes: a2ab7cb169da ("drm/panel: himax-hx83102: use wrapped MIPI DCS functions")
Signed-off-by: Tejas Vipin <tejasvipin76@gmail.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20240612133550.473279-2-tejasvipin76@gmail.com
[narmstrong: fixed subject and fixes tag]
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240612133550.473279-2-tejasvipin76@gmail.com
|
|
ctx would be better off treated as a pointer to account for most of its
usage so far, and brackets should be added to account for operator
precedence for correct evaluation.
Fixes: f79d6d28d8fe ("drm/mipi-dsi: wrap more functions for streamline handling")
Signed-off-by: Tejas Vipin <tejasvipin76@gmail.com>
Suggested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20240612133550.473279-3-tejasvipin76@gmail.com
[narmstrong: fixed fixes tag]
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240612133550.473279-3-tejasvipin76@gmail.com
|
|
In order to let bridge chains implement HDMI connector infrastructure,
add necessary glue code to the drm_bridge_connector. In case there is a
bridge that sets DRM_BRIDGE_OP_HDMI, drm_bridge_connector will register
itself as a HDMI connector and provide proxy drm_connector_hdmi_funcs
implementation.
Note, to simplify implementation, there can be only one bridge in a
chain that sets DRM_BRIDGE_OP_HDMI. Setting more than one is considered
an error. This limitation can be lifted later, if the need arises.
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240607-bridge-hdmi-connector-v5-3-ab384e6021af@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
Turn drm_bridge_connector to using drmm_kzalloc() and
drmm_connector_init() and drop the custom destroy function. The
drm_connector_unregister() and fwnode_handle_put() are already handled
by the drm_connector_cleanup() and so are safe to be dropped.
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240607-bridge-hdmi-connector-v5-2-ab384e6021af@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
Add drm_atomic_helper_connector_hdmi_disable_audio_infoframe(), an API
to allow the driver disable sending the Audio Infoframe. This is to be
used by the drivers if setup of the infoframes is not tightly coupled
with the audio functionality and just disabling the audio playback
doesn't stop the HDMI hardware from sending the Infoframe.
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240607-bridge-hdmi-connector-v5-1-ab384e6021af@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
The WA should be extended to cover VDBOX engine. We found that
28-channels 1080p VP9 encoding may hit this issue.
v3: update the WA number and explain the reason why
this workaround is needed
v2: add WA number
v1: initial version
Signed-off-by: Angus Chen <angus.chen@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240426073638.45775-1-angus.chen@intel.com
|
|
When checking vblank length used wake time is aux less wake time for eDP
Panel Replay (vblank length is not checked for DP2.0 Panel Replay).
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240607134917.1327574-14-jouni.hogander@intel.com
|
|
As Lunarlake doesn't have block count configuration vblank should be
checked against IO buffer wake time.
Bspec: 68920
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240607134917.1327574-13-jouni.hogander@intel.com
|
|
SU SDP scanline indication should be taken into account when checking
vblank length. In Bspec we have:
PSR2_CTL[ SU SDP scanline indication ] = 0: (TRANS_VBLANK Vertical Blank
End- TRANS_VBLANK Vertical Blank Start) > PSR2_CTL Block Count Number value
in lines
PSR2_CTL[ SU SDP scanline indication ] = 1: (TRANS_VBLANK Vertical Blank
End- TRANS_VBLANK Vertical Blank Start- 1) > PSR2_CTL Block Count Number
value in lines
Bspec: 49274
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240607134917.1327574-12-jouni.hogander@intel.com
|
|
We are about to add more complexity to vblank length check. It makes sense
to move it to separate function for sake of clarity.
v2: change name to wake_lines_fit_into_vblank
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240607134917.1327574-11-jouni.hogander@intel.com
|
|
Currently Panel Replay status printout is printing frame lock status. It
should print Panel Replay status instead. Panel Replay status register
field follows PSR status register field. Use existing PSR code for that.
Fixes: ef75c25e8fed ("drm/i915/panelreplay: Debugfs support for panel replay")
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240607134917.1327574-10-jouni.hogander@intel.com
|
|
Early Transport is possible and in our HW mandatory on eDP Panel
Replay. Add parameter to intel_psr2_config_et_valid to differentiate
validity check for Panel Replay.
v2: fix intel_dp->psr_dpcd[0] check
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240607134917.1327574-9-jouni.hogander@intel.com
|
|
Convert intel_alpm_aux_wake_supported and
intel_alpm_aux_less_wake_supported as non-static. Use them in intel_psr.c
instead of local variables.
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240607134917.1327574-8-jouni.hogander@intel.com
|
|
Current intel_psr_enable_sink is a mess due to partly reusing PSR bit
definitions for Panel Replay. Even thought PSR and Panel Replay enable
registers do have common bits they still have also different bits and same
bits with different meaning. For sake of clarity split enabling sink to PSR
and Panel Replay specific parts.
Also fix issue caused by using psr->panel_replay_enabled to early.
Fixes: 88ae6c65ecdb ("drm/i915/psr: Unify panel replay enable/disable sink")
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240607134917.1327574-7-jouni.hogander@intel.com
|
|
Add missing Panel Replay Enable SU Region ET bit defined in DP2.1
specification.
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240607134917.1327574-6-jouni.hogander@intel.com
|
|
Panel Replay is not enabled if there are no active planes. Do not compare
it on pipe comparison. Otherwise we get pipe mismatch.
Fixes: ac9ef327327b ("drm/i915/psr: Panel replay has to be enabled before link training")
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240607134917.1327574-5-jouni.hogander@intel.com
|
