summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2010-08-02omap3 gpmc: functionality enhancementSukumar Ghorai
few functions added in gpmc module and to be used by other drivers like NAND. Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-08-02Merge branch 'devel-misc' into omap-for-linusTony Lindgren
2010-08-02omap: mux: fix multipath gpio handlingGrazvydas Ignotas
OMAP3530 CBB package can have GPIO126 muxed on 2 pins: mmc1_dat4 and cam_strobe. This causes a problem with current multipath GPIO mux handling, which muxes both pins as GPIO126 and makes the GPIO unusable. Fix this by not muxing any pins if multipath GPIO is detected and just print a warning instead. It's up to board files to set correct mux using omap_mux_init_signal and pin name. Signed-off-by: Grazvydas Ignotas <notasas@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-08-02omap: Devkit8000: Use DIE id to initialize dm9000 MAC addressKan-Ru Chen
The devkit8000 boards often come with empty EEPROM thus without valid ethernet MAC address. The DIE id to MAC formula is copied from u-boot. Signed-off-by: Kan-Ru Chen <kanru@0xlab.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-08-02omap: Use omap_get_die_id() to get the DIE idsKan-Ru Chen
Signed-off-by: Kan-Ru Chen <kanru@0xlab.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-08-02omap: Add new interface omap_get_die_idKan-Ru Chen
Allow DIE id to be get and used by others. Signed-off-by: Kan-Ru Chen <kanru@0xlab.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-08-02OMAP3: AM3505/3517 do not have IO wakeup capabilitystanley.miao
AM3505/3517 doesn't have IO wakeup capability, so we do not need to set the bit OMAP3430_EN_IO and the bit OMAP3430_EN_IO_CHAIN in the register PM_WKEN_WKUP when the system enters suspend state. Tested on AM3517EVM and OMAP3530EVM. Signed-off-by: Stanley.Miao <stanley.miao@windriver.com> Acked-by: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-08-02omap: dma: Support for prefetch in destination synchronizedtransferSamu Onkalo
Omap DMA controller can prefetch data in advance in case of destination synchronized data transfer. This may increase performance when target HW block doesn't have fifo. Data is waiting for transfer request in DMA fifo instead of read from memory. Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-08-02omap2/3: id: fix sparse warningNishanth Menon
omap24xx_check_revision, omap3_check_features, omap3_check_revision, omap4_check_revision, omap3_cpuinfo are not used elsewhere, it should be static Also fixes the following sparse warnings: arch/arm/mach-omap2/id.c:105:13: warning: symbol 'omap24xx_check_revision' was not declared. Should it be static? arch/arm/mach-omap2/id.c:167:13: warning: symbol 'omap3_check_features' was not declared. Should it be static? arch/arm/mach-omap2/id.c:189:13: warning: symbol 'omap3_check_revision' was not declared. Should it be static? arch/arm/mach-omap2/id.c:270:13: warning: symbol 'omap4_check_revision' was not declared. Should it be static? arch/arm/mach-omap2/id.c:300:13: warning: symbol 'omap3_cpuinfo' was not declared. Should it be static? Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-08-02omap: Overo: Fix support for second ethernet portSteve Sakoman
The original patch got truncated when applied from patchwork.kernel.org as discussed at: http://www.mail-archive.com/linux-omap@vger.kernel.org/msg28953.html This patch supplies the missing chunks. Signed-off-by: Steve Sakoman <sakoman@gmail.com> [tony@atomide.com: added more info to the patch description] Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-08-02omap2: Fix GPIO numbers and smc91x for 2430sdpTony Lindgren
Fix GPIO numbers and smc91x for 2430sdp. The earlier code had cut and paste errors from 3430sdp code. Also, 2430 has five GPIO banks for a total of 160 GPIO lines. Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-08-02omap1: omap7xx clocks, mux, serial fixesCory Maccarrone
This change adds in the necessary clocks and mux pins for UART control on omap7xx devices. I also made a change in the serial code to only try and initialize two UARTs in omap_serial_init, as these devices don't have three. Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-08-02omap: Add back UART MDR1 check into uncompress.hTony Lindgren
Recent DEBUG_LL and uncompress.h changes removed the check_port() as pointed out by Cory Maccarrone <darkstar6262@gmail.com>. This causes some boards to not boot, so add back the MDR1 register check. The MDR1 register tells the mode of omap uart. Based on an earlier patch by Cory Maccarrone <darkstar6262@gmail.com>. Tested-by: Cory Maccarrone <darkstar6262@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-08-02omap4: hotplug: Add basic CPU hotplug supportSantosh Shilimkar
This patch adds cpu hotplug support for OMAP4430. Only CPU inactive state is supported as a low power state in the basic hot-plug support Signed-off-by: Rajendra Nayak <rnayak@ti.com> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Cc: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-08-02omap4: Add smc API to read AuxCoreBoot0 registerSantosh Shilimkar
This patch adds a secure API to read AuxCoreBoot0 register to check the cpu boot status. It also moves the other smc APIs to common omap44xx-smc.S. This APIs should not be marked as __INIT because we need these to be present for CPU hotplug Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-08-02omap4: suspend: Add basic system suspend supportRajendra Nayak
This patch adds support for basic suspend doing a CPUx wfi for OMAP4. All powerdomains are for now are kept programmed in ON state. Signed-off-by: Rajendra Nayak <rnayak@ti.com> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Cc: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-08-02omap2/3/4: serial: errata i202: fix for MDR1 accessDeepak K
Errata i202 (OMAP3430 - 1.12, OMAP3630 - 1.6): UART module MDR1 register access can cause a dummy underrun condition which could result in a freeze in the case of IrDA communication or if used as UART, corrupted data. Workaround is as follows for everytime MDR1 register is changed: * setup all required UART registers * setup MDR1.MODE_SELECT bit field * Wait 5 L4 clk cycles + 5 UART functional clock cycles * Clear the Tx and RX fifo using FCR register Note: The following step is not done as I am assuming it is not needed due to reconfiguration being done and there is no halted operation perse. * Read if required, the RESUME register to resume halted operation Based on an earlier patch at: http://git.omapzoom.org/?p=kernel/omap.git;a=commitdiff;h=42d4a342c009bd9727c100abc8a4bc3063c22f0c Signed-off-by: Deepak K <deepak.k@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-08-02omap2/3/4: serial: introduce errata handlingNishanth Menon
introduce silicon specific quirks as a errata handling mechanism as a start UART_ERRATA_FIFO_FULL_ABORT is used to handle the override for fifo full condition for rx and tx. Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-08-02omap2/3/4: serial: kill dev_attr_sleep_timeout sparse warnNishanth Menon
Remove the following sparse warnings by declaring attr as static: arch/arm/mach-omap2/serial.c:627:1: warning: symbol 'dev_attr_sleep_timeout' was not declared. Should it be static? Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-08-02omap2/3/4: serial: remove initialization sparse warningsNishanth Menon
Initialization of pointer should be done with NULL. Removes sparse warnings: arch/arm/mach-omap2/serial.c:566:17: warning: Using plain integer as NULL pointer arch/arm/mach-omap2/serial.c:567:17: warning: Using plain integer as NULL pointer Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-08-02omap3: serial: Add context save and restore for mcrGovindraj R
Adds context save/restore for mcr register as state of mcr register is lost after core off. Signed-off-by: Govindraj R <govindraj.raja@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-08-02omap4: Add OMAP4 Panda SupportDavid Anders
Add initial support for the OMAP4 based Panda Board. Signed-off-by: David Anders <x0132446@ti.com> [tony@atomide.com: selected board by default in Kconfig] Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-08-02OMAP4: Add GPIO LED support for SDP boardHemanth V
This patch adds support for GPIO LEDs present on OMAP4 SDP and Blaze boards. This basically adds platform data required by leds-gpio driver Signed-off-by: Hemanth V <hemanthv@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-08-02omap4: Board changes for 4430sdp tmp105 temperature sensorShubhrajyoti Datta
Adding board configuration for the tmp105 temperature sensor. The interface to the sensor is I2C. Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-08-02omap4: mmc: Fix the regulator resource for MMC2 on 4430sdpSantosh Shilimkar
The MMC1 and MMC2 cards have seperate LDO supplies. Current code assumes that they are powered by same LDO. This patch fixes the same and has VAUX1 as supply to MMC2 card. Signed-off-by: Rajendra Nayak <rnayak@ti.com> Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com> Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com> Tested-by: Kishore Kadiyala <kishore.kadiyala@ti.com> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-08-02omap: tsl2563 ALS support for Nokia N900Mathias Nyman
This commit will enable usage of tsl2563 ambient light sensor on Nokia N900. Signed-off-by: Ameya Palande <ameya.palande@nokia.com> Signed-off-by: Mathias Nyman <mathias.nyman@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-08-02omap: rx51: Add supply and data for the tpa6130a2 headphoneamplifierJarkko Nikula
With these and upcoming change to tpa6130a2 driver it's possible to add support for the TPA6130A2 headphone amplifier. Signed-off-by: Jarkko Nikula <jhnikula@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-08-02omap: rx51: Use REGULATOR_SUPPLY macro when initializingregulator consumersJarkko Nikula
There is REGULATOR_SUPPLY macro available for initializing the struct regulator_consumer_supply so use it where applicable (all other supplies than vdds_sdi) as it improves the readability. Signed-off-by: Jarkko Nikula <jhnikula@gmail.com> Acked-by: Eduardo Valentin <eduardo.valentin@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-08-02omap: rx51: Add platform_data for tlv320aic3x with reset gpionumberJarkko Nikula
Proper operation of the tlv320aic3x audio codec requires that reset sequencing is done in pair with supply voltages when using the regulator framework. Add the codec reset gpio used in Nokia RX51 to tlv320aic3x data. Signed-off-by: Jarkko Nikula <jhnikula@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-08-02omap: rx51: Set regulator V28 always onJarkko Nikula
It seems that the battery cover sensor in Nokia N900 is powered from the V28 domain. Now if this regulator is disabled it causes that the gpio 160 reads only zero which effectively causes uSD removal detection. Currently the bootloader enabled V28 is kept on but this may change in the future according to comment in drivers/regulator/core.c: regulator_has_full_constraints. Also if there are any consumers on the V28 domain doing regulator_enable regulator_disable cycle the V28 will be disabled after that. Prepare for these by defining the V28 as always_on regulator. Signed-off-by: Jarkko Nikula <jhnikula@gmail.com> Cc: Adrian Hunter <adrian.hunter@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-08-02omap3: pandora: add NAND and wifi supportGrazvydas Ignotas
Add platform data for NAND and wifi, also setup all GPIOs needed to use the wifi chip. Signed-off-by: Grazvydas Ignotas <notasas@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-08-02omap3: pandora: update gpio-keys dataGrazvydas Ignotas
Update gpio-keys setup so it matches what is on default firmware. Also make use of debounce feature in gpio-keys instead of setting it explicitly, as gpio-keys is now capable of using hardware debounce on OMAPs thanks to recent gpiolib changes. Also fix a sparce warning along the way. Signed-off-by: Grazvydas Ignotas <notasas@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-08-02omap: zoom3: wlan board muxingOhad Ben-Cohen
Add board muxing to support the wlan wl1271 chip that is hardwired to mmc2 (third mmc controller) on the ZOOM3. Signed-off-by: Ohad Ben-Cohen <ohadb@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-08-02omap: zoom2: wlan board muxingOhad Ben-Cohen
Add board muxing to support the wlan wl1271 chip that is hardwired to mmc2 (third mmc controller) on the ZOOM2. Signed-off-by: Ohad Ben-Cohen <ohadb@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-08-02Merge branch 'for-2.6.36' of ↵Takashi Iwai
git://git.kernel.org/pub/scm/linux/kernel/git/lrg/asoc-2.6 into topic/asoc
2010-08-02ASoC: omap-mcbsp: Remove period size constraint in THRESHOLD modePeter Ujfalusi
The use of sDMA packet mode in THRESHOLD mode removes the restriction on the period size. With the extended THRESHOLD mode user space can ask for any period size it wishes, and the driver will configure the sDMA and McBSP FIFO accordingly. Replace the hw_rule for the period size with static constraint, which will make sure that the period size will be always even (to avoid prime period size, which could be possible in mono stream) Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Jarkko Nikula <jhnikula@gmail.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-08-02ASoC: omap-mcbsp: Support for sDMA packet modePeter Ujfalusi
Utilize the sDMA controller's packet syncronization mode, when the McBSP FIFO is in use (by extending the THRESHOLD mode). When the sDMA is configured for packet mode, the sDMA frame size does not need to match with the McBSP threshold configuration. Uppon DMA request the sDMA will transfer packet size number of words, and still trigger interrupt on frame boundary. The patch extends the original THRESHOLD mode by doing the following: if (period_words <= max_threshold) Current THRESHOLD mode configuration Otherwise (period_words > max_threshold) McBSP threshold = sDMA packet size sDMA frame size = period size With the extended THRESHOLD mode we can remove the constraint for the maximum period size, since if the period size is bigger than the maximum allowed threshold, than the driver will switch to packet mode, and picks the best (biggest) threshold value, which can divide evenly the period size. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Jarkko Nikula <jhnikula@gmail.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-08-02ASoC: omap-mcbsp: Code cleanup in omap_mcbsp_dai_hw_paramsPeter Ujfalusi
To make the code a bit more readable, change the indexed references to the omap_mcbsp_dai_dma_params elements with pointer. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Jarkko Nikula <jhnikula@gmail.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-08-02ASoC: omap-mcbsp: Restructure the code within omap_mcbsp_dai_hw_paramsPeter Ujfalusi
In preparation for the extended threshold mode (sDMA packet mode support), the code need to be restructured. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Jarkko Nikula <jhnikula@gmail.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-08-02GFS2: Fix recovery stuck bug (try #2)Steven Whitehouse
This is a clean up of the code which deals with LM_FLAG_NOEXP which aims to remove any possible race conditions by using gl_spin to cover the gap between testing for the LM_FLAG_NOEXP and the GL_FROZEN flag. Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
2010-08-02microblaze: Fix comment for TLBMichal Simek
There is wrong comment for TLB. Early printk uartlite console uses TLB 63. Signed-off-by: Michal Simek <monstr@monstr.eu>
2010-08-02microblaze: Fix __copy_to/from_user_inatomic macrosMichal Simek
__copy_to/from_user_inatomic should call __copy_to/from_user because there is not necessary to check access because of kernel function. might_sleep in copy_to/from_user macros is causing problems in debug sessions too (CONFIG_DEBUG_SPINLOCK_SLEEP). BUG: sleeping function called from invalid context at .../arch/microblaze/include/asm/uaccess.h:388 in_atomic(): 1, irqs_disabled(): 0, pid: 1, name: swapper 1 lock held by swapper/1: #0: (&p->cred_guard_mutex){......}, at: [<c00d4b90>] prepare_bprm_creds+0x2c/0x88 Kernel Stack: ... Call Trace: [<c0006bd4>] microblaze_unwind+0x7c/0x94 [<c0006684>] show_stack+0xf4/0x190 [<c0006730>] dump_stack+0x10/0x30 [<c00103a0>] __might_sleep+0x12c/0x160 [<c0090de4>] file_read_actor+0x1d8/0x2a8 [<c0091568>] generic_file_aio_read+0x6b4/0xa64 [<c00cd778>] do_sync_read+0xac/0x110 [<c00ce254>] vfs_read+0xc8/0x160 [<c00d585c>] kernel_read+0x38/0x64 [<c00d5984>] prepare_binprm+0xfc/0x130 [<c00d6430>] do_execve+0x228/0x370 [<c000614c>] microblaze_execve+0x58/0xa4 caused by file_read_actor (mm/filemap.c) which calls __copy_to_user_inatomic. Signed-off-by: Michal Simek <monstr@monstr.eu>
2010-08-02mtd: onenand:fix for page addr calculation based on device typeRohit Hassan Sathyanarayan
Sending the patch for page address calculation based on device type. This resolves the OneNAND DDP device read problem as pointed by Enric. http://lists.infradead.org/pipermail/linux-mtd/2010-July/030920.html Signed-off-by: Rohit HS <rohit.hs@samsung.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-08-02mtd: nand: update nand_default_block_markbad()Brian Norris
This is an update that depends on the previous patches I sent. We can now write to all the appropriate BB marker locations (i.e. pages 1 AND 2, bytes 1 AND 6) with nand_default_block_markbad() if necessary, according to the flags marked in chip->options. Note that I removed the line: ofs += mtd->oobsize; Unless I am wrong, this line was completely unnecessary in the first place. Signed-off-by: Brian Norris <norris@broadcom.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-08-02mtd: denali.h: fixed checkpatch errorsDong, Chuanxiao
Fix all checkpatch.pl complaints. Artem: tweaked a little and fix tab indentations, so now this is not only about checkpatch, but also about making indentations look sane. Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-08-02mtd: nand: davinci: correct 4-bit error correctionSudhakar Rajashekhara
On TI's DA830/OMAP-L137, DA850/OMAP-L138 and DM365, after setting the 4BITECC_ADD_CALC_START bit in the NAND Flash control register to 1 and before waiting for the NAND Flash status register to be equal to 1, 2 or 3, we have to wait till the ECC HW goes to correction state. Without this wait, ECC correction calculations will not be proper. This has been tested on DA830/OMAP-L137, DA850/OMAP-L138, DM355 and DM365 EVMs. Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com> Acked-by: Sneha Narnakaje <nsnehaprabha@ti.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-08-02mtd: nand: more BB Detection refactoring and dynamic scan optionsBrian Norris
This is a revision to PATCH 2/2 that I sent. Link: http://lists.infradead.org/pipermail/linux-mtd/2010-July/030911.html Added new flag for scanning of both bytes 1 and 6 of the OOB for a BB marker (instead of simply one or the other). The "check_pattern" and "check_short_pattern" functions were updated to include support for scanning the two different locations in the OOB. In order to handle increases in variety of necessary scanning patterns, I implemented dynamic memory allocation of nand_bbt_descr structs in new function 'nand_create_default_bbt_descr()'. This replaces some increasingly-unwieldy, statically-declared descriptors. It can replace several more (e.g. "flashbased" structs). However, I do not test the flashbased options personally. How this was tested: I referenced 30+ data sheets (covering 100+ parts), and I tested a selection of 10 different chips to varying degrees. Particularly, I tested the creation of bad-block descriptors and basic BB scanning on three parts: ST NAND04GW3B2D, 2K page ST NAND128W3A, 512B page Samsung K9F1G08U0A, 2K page To test these, I wrote some fake bad block markers to the flash (in OOB bytes 1, 6, and elsewhere) to see if the scanning routine would detect them properly. However, this method was somewhat limited because the driver I am using has some bugs in its OOB write functionality. Signed-off-by: Brian Norris <norris@broadcom.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-08-02Merge firewire branches to be released post v2.6.35Stefan Richter
Conflicts: drivers/firewire/core-card.c drivers/firewire/core-cdev.c and forgotten #include <linux/time.h> in drivers/firewire/ohci.c Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2010-08-02mtd: nand: refactor BB marker detectionBrian Norris
Some level of support for various scanning locations was already built in, but this required clean-up. First, BB marker location cannot be determined _only_ by the page size. Instead, I implemented some heuristic detection based on data sheets from various manufacturers (all found in nand_base.c:nand_get_flash_type()). Second, once these options were identified, they were not handled properly by nand_bbt.c:nand_default_bbt(). I updated the static nand_bbt_desc structs to reflect the need for more combinations of detection. The memory allocation here probably needs to be done dynamically in the very near future (see next patches). Signed-off-by: Brian Norris <norris@broadcom.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-08-02mtd: s3c nand: parsing command-line partitions prior to set->partitionsConke Hu
Current driver prevents command-line partitions from being parsed when built-in partitions are defined in s3c2410_nand_set object, but it is not desirable in some cases. This patch tries to parse commad-line partitions prior to the built-in. Signed-off-by: Conke Hu <conke@maxwit.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
generated by cgit (git 2.34.1) at 2025-09-19 08:13:21 +0000