| Age | Commit message (Collapse) | Author |
|---|
|
Link speed advertising in igc has two problems:
- When setting the advertisement via ethtool, the link speed is converted
to the legacy 32 bit representation for the intel PHY code.
This inadvertently drops ETHTOOL_LINK_MODE_2500baseT_Full_BIT (being
beyond bit 31). As a result, any call to `ethtool -s ...' drops the
2500Mbit/s link speed from the PHY settings. Only reloading the driver
alleviates that problem.
Fix this by converting the ETHTOOL_LINK_MODE_2500baseT_Full_BIT to the
Intel PHY ADVERTISE_2500_FULL bit explicitly.
- Rather than checking the actual PHY setting, the .get_link_ksettings
function always fills link_modes.advertising with all link speeds
the device is capable of.
Fix this by checking the PHY autoneg_advertised settings and report
only the actually advertised speeds up to ethtool.
Fixes: 8c5ad0dae93c ("igc: Add ethtool support")
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
In time-travel mode, since my previous patch, the start time was
initialized too late, so that the system would read it before we
set it, thus always starting system time at 0 (1970-01-01). This
happens because timekeeping_init() reads the time and is called
before time_init().
Unfortunately, I didn't see this before because I was testing it
only with the RTC patch applied (and enabled), and then the time
is read again by the RTC a little - after time_init() this time.
Fix this by just doing the initialization whenever necessary.
Fixes: 2701c1bd91dd ("um: time: Fix read_persistent_clock64() in time-travel")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
Changing os_idle_sleep() to use pause() (I accidentally described
it as an empty select() in the commit log because I had changed it
from that to pause() in a later revision) exposed a race condition
in the idle code. The following can happen:
timer_settime(0, 0, {it_interval={tv_sec=0, tv_nsec=0}, it_value={tv_sec=0, tv_nsec=624017}}, NULL) = 0
...
<SIGALRM is delivered but we're already on the way to idle>
pause()
and we now hang forever. This was previously possible as well, but
it could never cause UML to hang for more than a second since we
could only sleep for that much, so at most you'd notice a "hiccup"
in the UML. Obviously, any sort of external interrupt also "saves"
it and interrupts pause().
Fix this by properly handling the race, rather than papering over
it again:
- first, block SIGALRM, and obtain the old signal set
- check the timer
- suspend, waiting for any signal out of the old set, if, and only
if, the timer will fire in the future
- restore the old signal mask
This ensures race-free operation: as it's blocked, the signal won't
be delivered while we're looking at the timer even if it were to be
triggered right _after_ we've returned from timer_gettime() with a
non-zero value (telling us the timer will trigger). Thus, despite
getting to sigsuspend() because timer_gettime() told us we're still
waiting, we'll not hang because sigsuspend() will return immediately
due to the pending signal.
Fixes: 49da38a3ef33 ("um: Simplify os_idle_sleep() and sleep longer")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-By: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
This reverts commit 963285b0b47a ("um: support some of
ARCH_HAS_SET_MEMORY"), as it turns out that it's not only not
working (due to um never using the protection bits in the
page tables) but also corrupts the page tables if used on a
non-vmalloc page, since um never allocates proper page tables
for the 'physmem' in the first place.
Fixing all this will take more effort, so for now revert it.
Reported-by: Benjamin Berg <benjamin@sipsolutions.net>
Fixes: 963285b0b47a ("um: support some of ARCH_HAS_SET_MEMORY")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
This reverts commit ef4459a6da09 ("um: allocate a guard page to
helper threads"), it's broken in multiple ways:
1) the free no longer matches the alloc; and
2) more importantly, the set_memory_ro() causes allocation of
page tables for the normal memory that doesn't have any,
and that later causes corruption and crashes (usually but
not always in vfree()).
We could fix the first bug and use vmalloc() to work around the
second, but set_memory_ro() actually doesn't do anything either
so I'll just revert that as well.
Reported-by: Benjamin Berg <benjamin@sipsolutions.net>
Fixes: ef4459a6da09 ("um: allocate a guard page to helper threads")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
Since struct device is refcounted, we shouldn't free the vu_dev
immediately when it's removed from the platform device, but only
when the references actually all go away. Move the freeing to
the release to accomplish that.
Fixes: 5d38f324993f ("um: drivers: Add virtio vhost-user driver")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
With the addition of the ttynull console driver, the chance that a
console driver was already registerd did increase. Refine the logic when
to dump the kernel message buffer: always dump the buffer, when the UML
stdio console driver is not active and the preferred console.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
The addition of the "ttynull" console driver did break the ordering of the
UML stdio console driver.
The UML stdio console driver is added in late_initcall (7), whereby the
ttynull driver is added in device_initcall (6), which always does make the
ttynull driver the default console.
Fix it by explicitly adding the UML stdio console as the preferred console,
in case no 'console=' command line option was specified.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
Back a few years ago, ioremap() was added to UML so that we'd
not break the build for everything all the time. However, for
some reason, v1 of the patch got applied, rather than the v2
that returned NULL, which was discussed here:
https://lore.kernel.org/lkml/1495726955-27497-1-git-send-email-logang@deltatee.com/
Fix that now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
This commit fixes a regression to handle command line parameters of ubd.
With a simple line "./linux ubd0="./disk-ext4.img", it fails at
ubd_setup_common(). The commit adds additional checks to the variables
in order to properly parse the paremeters which previously worked.
Fixes: ef3ba87cb7c9 ("um: ubd: Set device serial attribute from cmdline")
Cc: Christopher Obbard <chris.obbard@collabora.com>
Signed-off-by: Hajime Tazaki <thehajime@gmail.com>
Acked-by: Christopher Obbard <chris.obbard@collabora.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/fixes
Qualcomm ARM64 defconfig fixes for v5.11
Devicetree patches for SDM845 introduced in v5.11 requires the
platform's interconnect driver to be buildin, or the kernel will fail to
provide a valid console when we hit userspace.
* tag 'qcom-arm64-defconfig-fixes-for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
arm64: defconfig: Make INTERCONNECT_QCOM_SDM845 builtin
Link: https://lore.kernel.org/r/20210125232412.642834-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/fixes
Qualcomm ARM64 fixes for 5.11
This fixes a regression in Lenovo Yoga C630, where the touchpad in some
units stopped working, by re-enabling the "tsc2" device.
It also marks the LPASS related clocks as protected to allow DB845c and
the Lenovo Yoga C630 to boot even if CONFIG_SDM_LPASSCC_845 is enabled.
* tag 'qcom-arm64-fixes-for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
arm64: dts: qcom: sdm845: Reserve LPASS clocks in gcc
arm64: dts: qcom: c630: keep both touchpad devices enabled
Link: https://lore.kernel.org/r/20210125232039.642565-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into arm/fixes
arm64: dts: amlogic: fixes for v5.11-rc
- meson-g12: Set FL-adj property value
* tag 'amlogic-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
arm64: dts: amlogic: meson-g12: Set FL-adj property value
Link: https://lore.kernel.org/r/7hk0s0x3im.fsf@baylibre.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into arm/fixes
STM32 DT fixes for v5.11, round 1
Highlights:
-----------
-Fixes are for DHCOM/DHCOR boards:
- Fix DRC02 uSD card detect polarity
- use uSD card detect on DHCOM
- Disable uSD WP on DHCOM
- Disable TSC2004 on DRC02
- Fix GPIO hogs on DHCOM boards
* tag 'stm32-dt-for-v5.11-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
ARM: dts: stm32: Fix GPIO hog flags on DHCOM DRC02
ARM: dts: stm32: Fix GPIO hog flags on DHCOM PicoITX
ARM: dts: stm32: Fix GPIO hog names on DHCOM
ARM: dts: stm32: Disable optional TSC2004 on DRC02 board
ARM: dts: stm32: Disable WP on DHCOM uSD slot
ARM: dts: stm32: Connect card-detect signal on DHCOM
ARM: dts: stm32: Fix polarity of the DH DRC02 uSD card detect
Link: https://lore.kernel.org/r/b7379980-857e-736a-85d8-58e2bd300141@foss.st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Remove the magical "repo-abbrev" comment added when this file was
introduced in e0ab1ec9fcd3 ([PATCH] add .mailmap for proper
git-shortlog output, 2007-02-14).
It's been an undocumented feature of git-shortlog(1), originally added
to git for Linus's use. Since then he's no longer using it[1], and
I've removed the feature in git.git's 4e168333a87 (shortlog: remove
unused(?) "repo-abbrev" feature, 2021-01-12). It's on the "master"
branch, but not yet in a release version.
Let's also remove it from linux.git, both as a heads-up to any
potential users of it in linux.git whose use would be broken sooner
than later by git itself, and because it'll eventually be entirely
redundant.
1. https://lore.kernel.org/git/CAHk-=wixHyBKZVUcxq+NCWMbkrX0xnppb7UCopRWw1+oExYpYw@mail.gmail.com/
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ævar Arnfjörð Bjarmason <avarab@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When building a kernel without module support, the CONFIG_MLONGCALL option
needs to be enabled in order to reach symbols which are outside of a 22-bit
branch.
This patch changes the autodetection in the Kconfig script to always enable
CONFIG_MLONGCALL when modules are disabled and uses a far call to
preempt_schedule_irq() in intr_do_preempt() to reach the symbol in all cases.
Signed-off-by: Helge Deller <deller@gmx.de>
Reported-by: kernel test robot <lkp@intel.com>
Cc: stable@vger.kernel.org # v5.6+
|
|
Pull kvm fixes from Paolo Bonzini:
- x86 bugfixes
- Documentation fixes
- Avoid performance regression due to SEV-ES patches
- ARM:
- Don't allow tagged pointers to point to memslots
- Filter out ARMv8.1+ PMU events on v8.0 hardware
- Hide PMU registers from userspace when no PMU is configured
- More PMU cleanups
- Don't try to handle broken PSCI firmware
- More sys_reg() to reg_to_encoding() conversions
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: allow KVM_REQ_GET_NESTED_STATE_PAGES outside guest mode for VMX
KVM: x86: Revert "KVM: x86: Mark GPRs dirty when written"
KVM: SVM: Unconditionally sync GPRs to GHCB on VMRUN of SEV-ES guest
KVM: nVMX: Sync unsync'd vmcs02 state to vmcs12 on migration
kvm: tracing: Fix unmatched kvm_entry and kvm_exit events
KVM: Documentation: Update description of KVM_{GET,CLEAR}_DIRTY_LOG
KVM: x86: get smi pending status correctly
KVM: x86/pmu: Fix HW_REF_CPU_CYCLES event pseudo-encoding in intel_arch_events[]
KVM: x86/pmu: Fix UBSAN shift-out-of-bounds warning in intel_pmu_refresh()
KVM: x86: Add more protection against undefined behavior in rsvd_bits()
KVM: Documentation: Fix spec for KVM_CAP_ENABLE_CAP_VM
KVM: Forbid the use of tagged userspace addresses for memslots
KVM: arm64: Filter out v8.1+ events on v8.0 HW
KVM: arm64: Compute TPIDR_EL2 ignoring MTE tag
KVM: arm64: Use the reg_to_encoding() macro instead of sys_reg()
KVM: arm64: Allow PSCI SYSTEM_OFF/RESET to return
KVM: arm64: Simplify handling of absent PMU system registers
KVM: arm64: Hide PMU registers from userspace when not available
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"One new device ID here, plus an error handling fix - nothing
remarkable in either"
* tag 'spi-fix-v5.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spidev: Add cisco device compatible
spi: altera: Fix memory leak on error path
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"The main thing here is a change to make sure that we don't try to
double resolve the supply of a regulator if we have two probes going
on simultaneously, plus an incremental fix on top of that to resolve a
lockdep issue it introduced.
There's also a patch from Dmitry Osipenko adding stubs for some
functions to avoid build issues in consumers in some configurations"
* tag 'regulator-fix-v5.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: Fix lockdep warning resolving supplies
regulator: consumer: Add missing stubs to regulator/consumer.h
regulator: core: avoid regulator_resolve_supply() race condition
|
|
This was removed long ago, back in:
6e16d9409e1 ([PARISC] Convert soft power switch driver to kthread)
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
This change simplifies the VF initialization check and also minimizes
the delay between acquiring the VSI pointer and using it. As known by
the commit being fixed, there is a risk of the VSI pointer getting
changed. Therefore minimize the delay between getting and using the
pointer.
Fixes: 9889707b06ac ("i40e: Fix crash caused by stress setting of VF MAC addresses")
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The current MSI-X enablement logic tries to enable best-case MSI-X
vectors and if that fails we only support a bare-minimum set. This
includes a single MSI-X for 1 Tx and 1 Rx queue and a single MSI-X
for the OICR interrupt. Unfortunately, the driver fails to load when we
don't get as many MSI-X as requested for a couple reasons.
First, the code to allocate MSI-X in the driver tries to allocate
num_online_cpus() MSI-X for LAN traffic without caring about the number
of MSI-X actually enabled/requested from the kernel for LAN traffic.
So, when calling ice_get_res() for the PF VSI, it returns failure
because the number of available vectors is less than requested. Fix
this by not allowing the PF VSI to allocation more than
pf->num_lan_msix MSI-X vectors and pf->num_lan_msix Rx/Tx queues.
Limiting the number of queues is done because we don't want more than
1 Tx/Rx queue per interrupt due to performance conerns.
Second, the driver assigns pf->num_lan_msix = 2, to account for LAN
traffic and the OICR. However, pf->num_lan_msix is only meant for LAN
MSI-X. This is causing a failure when the PF VSI tries to
allocate/reserve the minimum pf->num_lan_msix because the OICR MSI-X has
already been reserved, so there may not be enough MSI-X vectors left.
Fix this by setting pf->num_lan_msix = 1 for the failure case. Then the
ICE_MIN_MSIX accounts for the LAN MSI-X and the OICR MSI-X needed for
the failure case.
Update the related defines used in ice_ena_msix_range() to align with
the above behavior and remove the unused RDMA defines because RDMA is
currently not supported. Also, remove the now incorrect comment.
Fixes: 152b978a1f90 ("ice: Rework ice_ena_msix_range")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Currently users could create more channels than LAN MSI-X available.
This is happening because there is no check against pf->num_lan_msix
when checking the max allowed channels and will cause performance issues
if multiple Tx and Rx queues are tied to a single MSI-X. Fix this by not
allowing more channels than LAN MSI-X available in pf->num_lan_msix.
Fixes: 87324e747fde ("ice: Implement ethtool ops for channels")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Fix the driver to copy the MAC address configured in ndo_set_mac_address
into dev_addr, even if the MAC filter already exists in HW. In some
situations (e.g. bonding) the netdev's dev_addr could have been modified
outside of the driver, with no change to the HW filter, so the driver
cannot assume that they match.
Fixes: 757976ab16be ("ice: Fix check for removing/adding mac filters")
Signed-off-by: Nick Nunley <nicholas.d.nunley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
This patch is based on a similar change to i40e by Slawomir Laba:
"i40e: Implement flow for IPv6 next header (extension header)".
When a packet contains an IPv6 header with next header which is
an extension header and not a protocol one, the kernel function
skb_transport_header called with such sk_buff will return a
pointer to the extension header and not to the TCP one.
The above explained call caused a problem with packet processing
for skb with encapsulation for tunnel with ICE_TX_CTX_EIPT_IPV6.
The extension header was not skipped at all.
The ipv6_skip_exthdr function does check if next header of the IPV6
header is an extension header and doesn't modify the l4_proto pointer
if it points to a protocol header value so its safe to omit the
comparison of exthdr and l4.hdr pointers. The ipv6_skip_exthdr can
return value -1. This means that the skipping process failed
and there is something wrong with the packet so it will be dropped.
Fixes: a4e82a81f573 ("ice: Add support for tunnel offloads")
Signed-off-by: Nick Nunley <nicholas.d.nunley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The packet classifier would occasionally misrecognize an IPv6 training
packet when the next protocol field was 0. The correct value for
unspecified protocol is IPPROTO_NONE.
Fixes: 165d80d6adab ("ice: Support IPv6 Flow Director filters")
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
This reverts commit d3921cb8be29ce5668c64e23ffdaeec5f8c69399.
Chris Wilson reports that it causes boot problems:
"We have half a dozen or so different machines in CI that are silently
failing to boot, that we believe is bisected to this patch"
and the CI team confirmed that a revert fixed the issues.
The cause is unknown for now, so let's revert it.
Link: https://lore.kernel.org/lkml/161160687463.28991.354987542182281928@build.alporthouse.com/
Reported-and-tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Mike Rapoport <rppt@linux.ibm.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit c0f975af1745 ("kconfig: Support building mconf with vendor
sysroot ncurses") introduces a bug when HOSTCC contains parameters:
the whole command line is treated as the program name (with spaces
in it). Therefore, we have to remove the quotes.
Fixes: c0f975af1745 ("kconfig: Support building mconf with vendor sysroot ncurses")
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
raw_fmt->height in never initialized. But width in initialized twice.
Fixes: 88d06362d1d05 ("media: hantro: Refactor for V4L2 API spec compliancy")
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Missing stm32 directory to Makefile.
Signed-off-by: Yannick Fertre <yannick.fertre@foss.st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: 4be5e8648b0c ("media: move CEC platform drivers to a separate directory")
Cc: <stable@vger.kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
During H264 API overhaul subtle bug was introduced Cedrus driver.
Progressive references have both, top and bottom reference flags set.
Cedrus reference list expects only bottom reference flag and only when
interlaced frames are decoded. However, due to a bug in Cedrus check,
exclusivity is not tested and that flag is set also for progressive
references. That causes "jumpy" background with many videos.
Fix that by checking that only bottom reference flag is set in control
and nothing else.
Tested-by: Andre Heider <a.heider@gmail.com>
Fixes: cfc8c3ed533e ("media: cedrus: h264: Properly configure reference field")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The BIT macro is not available in userspace, so replace BIT(0) by
0x00000001.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: 6446ec6cbf46 ("media: v4l2-subdev: add VIDIOC_SUBDEV_QUERYCAP ioctl")
Cc: <stable@vger.kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Currently, the __is_lm_address() check just masks out the top 12 bits
of the address, but if they are 0, it still yields a true result.
This has as a side effect that virt_addr_valid() returns true even for
invalid virtual addresses (e.g. 0x0).
Fix the detection checking that it's actually a kernel address starting
at PAGE_OFFSET.
Fixes: 68dd8ef32162 ("arm64: memory: Fix virt_addr_valid() using __is_lm_address()")
Cc: <stable@vger.kernel.org> # 5.4.x
Cc: Will Deacon <will@kernel.org>
Suggested-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Link: https://lore.kernel.org/r/20210126134056.45747-1-vincenzo.frascino@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
The OBJECT_FILES_NON_STANDARD annotation is used to tell objtool to
ignore a file. File-level ignores won't work when validating vmlinux.o.
Instead, convert restore_image() and core_restore_code() to be ELF
functions. Their code is conventional enough for objtool to be able to
understand them.
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lore.kernel.org/r/974f8ceb5385e470f72e93974c70ab5c894bb0dc.1611263462.git.jpoimboe@redhat.com
|
|
Because restore_registers() is page-aligned, the assembler inexplicably
adds an unreachable jump from after the end of the previous function to
the beginning of restore_registers().
That confuses objtool, understandably. It also creates significant text
fragmentation. As a result, most of the object file is wasted text
(nops).
Move restore_registers() to the beginning of the file to both prevent
the text fragmentation and avoid the dead jump instruction.
$ size /tmp/hibernate_asm_64.before.o /tmp/hibernate_asm_64.after.o
text data bss dec hex filename
4415 0 0 4415 113f /tmp/hibernate_asm_64.before.o
524 0 0 524 20c /tmp/hibernate_asm_64.after.o
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lore.kernel.org/r/8c7f634201d26453d73fe55032cbbdc05d004387.1611263462.git.jpoimboe@redhat.com
|
|
These indirect jumps are harmless; annotate them to make objtool's
retpoline validation happy.
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lore.kernel.org/r/ba7a141c98f2c09c255b19bf78ee4a5f45d4ecb6.1611263462.git.jpoimboe@redhat.com
|
|
The OBJECT_FILES_NON_STANDARD annotation is used to tell objtool to
ignore a file. File-level ignores won't work when validating vmlinux.o.
Instead, tell objtool to ignore do_suspend_lowlevel() directly with the
STACK_FRAME_NON_STANDARD annotation.
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Len Brown <len.brown@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lore.kernel.org/r/269eda576c53bc9ecc8167c211989111013a67aa.1611263462.git.jpoimboe@redhat.com
|
|
This indirect jump is harmless; annotate it to keep objtool's retpoline
validation happy.
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Len Brown <len.brown@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lore.kernel.org/r/a7288e7043265d95c1a5d64f9fd751ead4854bdc.1611263462.git.jpoimboe@redhat.com
|
|
With objtool vmlinux.o validation of return_to_handler(), now that
objtool has visibility inside the retpoline, jumping from EMPTY state to
a proper function state results in a stack state mismatch.
return_to_handler() is actually quite normal despite the underlying
magic. Just annotate it as a normal function.
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lore.kernel.org/r/14f48e623f61dbdcd84cf27a56ed8ccae73199ef.1611263462.git.jpoimboe@redhat.com
|
|
This indirect jump is harmless; annotate it to keep objtool's retpoline
validation happy.
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Juergen Gross <jgross@suse.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/4797c72a258b26e06741c58ccd4a75c42db39c1d.1611263462.git.jpoimboe@redhat.com
|
|
The Xen hypercall page is filled with zeros, causing objtool to fall
through all the empty hypercall functions until it reaches a real
function, resulting in a stack state mismatch.
The build-time contents of the hypercall page don't matter because the
page gets rewritten by the hypervisor. Make it more palatable to
objtool by making each hypervisor function a true empty function, with
nops and a return.
Cc: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lore.kernel.org/r/0883bde1d7a1fb3b6a4c952bc0200e873752f609.1611263462.git.jpoimboe@redhat.com
|
|
The OBJECT_FILES_NON_STANDARD annotation is used to tell objtool to
ignore a file. File-level ignores won't work when validating vmlinux.o.
Tweak the ELF metadata and unwind hints to allow objtool to follow the
code.
Cc: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lore.kernel.org/r/8b042a09c69e8645f3b133ef6653ba28f896807d.1611263462.git.jpoimboe@redhat.com
|
|
xen_start_kernel() doesn't return. Annotate it as such so objtool can
follow the code flow.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lore.kernel.org/r/930deafa89256c60b180442df59a1bbae48f30ab.1611263462.git.jpoimboe@redhat.com
|
|
The ORC metadata generated for UNWIND_HINT_FUNC isn't actually very
func-like. With certain usages it can cause stack state mismatches
because it doesn't set the return address (CFI_RA).
Also, users of UNWIND_HINT_RET_OFFSET no longer need to set a custom
return stack offset. Instead they just need to specify a func-like
situation, so the current ret_offset code is hacky for no good reason.
Solve both problems by simplifying the RET_OFFSET handling and
converting it into a more useful UNWIND_HINT_FUNC.
If we end up needing the old 'ret_offset' functionality again in the
future, we should be able to support it pretty easily with the addition
of a custom 'sp_offset' in UNWIND_HINT_FUNC.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lore.kernel.org/r/db9d1f5d79dddfbb3725ef6d8ec3477ad199948d.1611263462.git.jpoimboe@redhat.com
|
|
To be used for adding asm functions to the ignore list. The "aw" is
needed to help the ELF section metadata match GCC-created sections.
Otherwise the linker creates duplicate sections instead of combining
them.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lore.kernel.org/r/8faa476f9a5ac89af27944ec184c89f95f3c6c49.1611263462.git.jpoimboe@redhat.com
|
|
There's an inconsistency in how sibling calls are detected in
non-function asm code, depending on the scope of the object. If the
target code is external to the object, objtool considers it a sibling
call. If the target code is internal but not a function, objtool
*doesn't* consider it a sibling call.
This can cause some inconsistencies between per-object and vmlinux.o
validation.
Instead, assume only ELF functions can do sibling calls. This generally
matches existing reality, and makes sibling call validation consistent
between vmlinux.o and per-object.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lore.kernel.org/r/0e9ab6f3628cc7bf3bde7aa6762d54d7df19ad78.1611263461.git.jpoimboe@redhat.com
|
|
Prevent an unreachable objtool warning after the sibling call detection
gets improved. ftrace_stub() is basically a function, annotate it as
such.
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lore.kernel.org/r/6845e1b2fb0723a95740c6674e548ba38c5ea489.1611263461.git.jpoimboe@redhat.com
|
|
Objtool converts direct retpoline jumps to type INSN_JUMP_DYNAMIC, since
that's what they are semantically.
That conversion doesn't work in vmlinux.o validation because the
indirect thunk function is present in the object, so the intra-object
jump check succeeds before the retpoline jump check gets a chance.
Rearrange the checks: check for a retpoline jump before checking for an
intra-object jump.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lore.kernel.org/r/4302893513770dde68ddc22a9d6a2a04aca491dd.1611263461.git.jpoimboe@redhat.com
|
|
With my version of GCC 9.3.1 the ".cold" subfunctions no longer have a
numbered suffix, so the trailing period is no longer there.
Presumably this doesn't yet trigger a user-visible bug since most of the
subfunction detection logic is duplicated. I only found it when
testing vmlinux.o validation.
Fixes: 54262aa28301 ("objtool: Fix sibling call detection")
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lore.kernel.org/r/ca0b5a57f08a2fbb48538dd915cc253b5edabb40.1611263461.git.jpoimboe@redhat.com
|
|
The JMP_NOSPEC macro branches to __x86_retpoline_*() rather than the
__x86_indirect_thunk_*() wrappers used by C code. Detect jumps to
__x86_retpoline_*() as retpoline dynamic jumps.
Presumably this doesn't trigger a user-visible bug. I only found it
when testing vmlinux.o validation.
Fixes: 39b735332cb8 ("objtool: Detect jumps to retpoline thunks")
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lore.kernel.org/r/31f5833e2e4f01e3d755889ac77e3661e906c09f.1611263461.git.jpoimboe@redhat.com
|
