| Age | Commit message (Collapse) | Author |
|---|
|
This patch improves the sequence the resources are released by, first,
- disabling the IRQ in the controller, then by
- resetting the DMA logic, and finally, by
- adding a read cycle to ensure that the above commands have been received
before freeing the system interrupt.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch fixes a typo in the error message in pciefd_can_probe().
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This cosmetic change should facilitate in the future the use of MSI
rather than legacy INTx interrupts.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
CANFD_IRQ_SET as well as CANFD_TX_PATH_SET are not used.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The embedded firmware aligns its messages on 32-bit boundaries.
This patch makes sure to browse through the list of received messages
while respecting 32-bit alignment.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Add support for Xilinx CAN FD core.
The major difference from the previously supported cores is that there
are TX mailboxes instead of a TX FIFO and the RX FIFO access method is
different.
We only transmit one frame at a time to prevent the HW from reordering
frames (it uses CAN ID priority order).
Support for CAN FD protocol is not added yet.
v2: Removed unnecessary "rx-mode" DT property and wrapped some long
lines.
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Xilinx CAN FD cores are different enough from the previous Zynq and AXI
CAN cores that some refactoring of the driver is needed.
This commit contains most of the required refactoring to existing code
and should not alter behavior on existing supported HW.
The changes are:
- Reading and writing to frame registers is parametrized to allow
reading/writing a different frame in the future.
- Slightly misleading (as it did not specify *all* the interrupts
supported by the HW) XCAN_INTR_ALL is replaced with specifying the
interrupts inline in interrupt enabling code.
- xcan_devtype_data.caps is renamed to xcan_devtype_data.flags to allow
for flags that define alternative functionality (e.g. mailboxes vs.
FIFO) instead of purely additive capabilities.
- can_bittiming_const is added to xcan_devtype_data as CAN FD cores will
have wider setting ranges.
- bus_clk clock name is now determined through xcan_devtype_data instead
of comparing compatible string in probe().
- xcan_devtype_data is added to xcan_priv to allow flag checks after
probe().
- XCAN_CAP_WATERMARK is now XCAN_FLAG_TXFEMP. CAN FD cores have
watermark support but no TXFEMP interrupt, which is what we are
actually interested in.
- xcan_start_xmit() is split to in two parts to prepare for TX mailboxes
instead of FIFO in CAN FD cores.
v2: Wrapped some long lines in xcan_write_frame().
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Add compatible string and new attributes to support the Xilinx CAN FD
core.
Unlike the previously documented Xilinx CAN cores, the CAN FD core has
TX mailboxes instead of TX FIFO, and optionally RX mailboxes instead of
RX FIFO (selected at core generation time, not switchable at runtime).
Add "tx-mailbox-count" and "rx-mailbox-count" to specify the mailbox
counts instead of reusing "tx-fifo-depth" and "rx-fifo-depth".
The RX FIFO depth is constant 32, but allow it to be specified via
"rx-fifo-depth" to match DT usage with Zynq CAN (which has constant RX
FIFO of depth of 64).
v2: Remove unnecessary "rx-mode" DT property.
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The driver updates stats.tx_bytes in start_xmit() even though it could
do so in TX interrupt handler.
Change the code to update tx_bytes in the interrupt handler, using the
return value of can_get_echo_skb().
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Replace some custom code with a call to can_change_state().
This subtly changes the error reporting behavior when both RX and TX
error counters indicate the same state.
Previously, if both RX and TX counters indicated the same state:
- if overall state is PASSIVE, report CAN_ERR_CRTL_RX_PASSIVE
- if overall state is WARNING, report CAN_ERR_CRTL_TX_WARNING or
CAN_ERR_CRTL_RX_WARNING depending on which counter is higher,
or CAN_ERR_CRTL_RX_WARNING if the counters have the same value.
After this commit:
- report RX_* or TX_* depending on which counter is higher, or both if
the counters have exactly the same value.
This behavior is consistent with many other CAN drivers that use this
same code pattern.
Tested with the integrated CAN on Zynq-7000 SoC.
v2: Simplify resolving states as suggested by Andri Yngvason.
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The xilinx_can driver currently increments error-warning and
error-passive statistics on every error interrupt regardless of whether
the interface was already in the same state. Similarly, the error frame
sent on error interrupts is always sent with
CAN_ERR_CRTL_(RX|TX)_(PASSIVE|WARNING) bit set.
To make the error-warning and error-passive statistics more useful, add
a check to only set the error state when the state has actually been
changed.
Tested with the integrated CAN on Zynq-7000 SoC.
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
pcan_add_channels() is never called in atomic context.
pcan_add_channels() is only called by pcan_probe(), which is only set as
".probe" in struct pcmcia_driver.
Despite never getting called from atomic context, pcan_add_channels()
calls mdelay() to busily wait.
This is not necessary and can be replaced with usleep_range() to
avoid busy waiting.
This is found by a static analysis tool named DCNS written by myself.
And I also manually check it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
peak_pci_probe() is never called in atomic context.
peak_pci_probe() is set as ".probe" in struct pci_driver.
Despite never getting called from atomic context, peak_pci_probe()
calls mdelay() to busily wait.
This is not necessary and can be replaced with usleep_range() to
avoid busy waiting.
This is found by a static analysis tool named DCNS written by myself.
And I also manually check it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.
Fix this by returning 'netdev_tx_t' in this driver too.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.
Fix this by returning 'netdev_tx_t' in this driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.
Fix this by returning 'netdev_tx_t' in this driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.
Fix this by returning 'netdev_tx_t' in this driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The existing SocketCAN implementation provides alloc_candev() to
allocate a CAN device using a single Tx and Rx queue. This can lead to
priority inversion in case the single Tx queue is already full with low
priority messages and a high priority message needs to be sent while the
bus is fully loaded with medium priority messages.
This problem can be solved by using the existing multi-queue support of
the network subsytem. The commit makes it possible to use multi-queue in
the CAN subsystem in the same way it is used in the Ethernet subsystem
by adding an alloc_candev_mqs() call and accompanying macros. With this
support a CAN device can use multi-queue qdisc (e.g. mqprio) to avoid
the aforementioned priority inversion.
The exisiting functionality of alloc_candev() is the same as before.
CAN devices need to have prioritized multiple hardware queues or are
able to abort waiting for arbitration to make sensible use of
multi-queues.
Signed-off-by: Zhu Yi <yi.zhu5@cn.bosch.com>
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
use helper skb_put_zero to replace the pattern of skb_put() && memset()
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The UCAN driver supports the microcontroller-based USB/CAN
adapters from Theobroma Systems. There are two form-factors
that run essentially the same firmware:
* Seal: standalone USB stick ( https://www.theobroma-systems.com/seal )
* Mule: integrated on the PCB of various System-on-Modules from
Theobroma Systems like the A31-µQ7 and the RK3399-Q7
( https://www.theobroma-systems.com/rk3399-q7 )
The USB wire protocol has been designed to be as generic and
hardware-indendent as possible in the hope of being useful for
implementation on other microcontrollers.
Signed-off-by: Martin Elshuber <martin.elshuber@theobroma-systems.com>
Signed-off-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch sorts the entries in the Kconfig and Makefile alphabetically,
so that further contributors can generate patches more easily.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Trivial fix to spelling mistake in module parameter description text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The CAN error masks header file is in the
include/uapi directory.
Fix the path in the header to the correct location.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Tobin C. Harding says:
====================
Recently BPF docs were converted to RST format. A couple of things were
missed:
- Use 'index.rst' instead of 'README.rst'. Although README.rst will
work just fine it is more typical to keep the subdirectory indices
in a file called 'index.rst'.
- Integrate files Documentation/bpf/*.rst into build system using
toctree in Documentation/bpf/index.rst
- Include bpf/index in top level toctree so bpf is indexed in the main
kernel docs.
- Make anal change to heading format (inline with rest of Documentation/).
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
The majority of files in the kernel documentation index use
capitalisation for all words, especially the shorter ones. BPF docs
better fit in with the rest of the documentation if the heading is all
capitalised.
Capitalise document heading.
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Recently bpf docs were converted to RST format. The new files were not
added to the top level toctree. This causes build system to emit a
warning of type
WARNING: document isn't included in any toctree
Add bpf/index.rst to Documentation/index.rst
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Recently bpf/ docs were converted to us RST format. bp/index.rst was
created out of README but toctree was not added to include files within
Documentation/bpf/
Add toctree to Documentation/bpf/index.rst
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Recently bpf/ docs were converted to use RST format. 'README.rst' was
created but in order to fit in with the Sphinx build system this file
should be named 'index.rst'. Rename file, fixes to integrate into
Sphinx build system in following patches.
docs: Rename Documentation/bpf/README.rst to Documentation/bpf/index.rst
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Jakub Kicinski says:
====================
This set converts xdpsock_user.c and xdp_fwd_user.c to use libbpf instead
of bpf_load.o. First two patches are minor improvements to libbpf to make
the conversion (and use of libbpf in general) nicer.
====================
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Convert xdpsock_user.c to use libbpf instead of bpf_load.o.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Convert xdp_fwd_user.c to use libbpf instead of bpf_load.o.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Allow users to find programs by section names.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
bpf_map__fd() handles NULL map gracefully and returns -EINVAL.
bpf_program__fd() and bpf_program__nth_fd() crash in this case.
Make the behaviour more consistent by validating prog pointer
as well.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Jakub Kicinski says:
====================
This set is focused on improving the performance of perf events
reported from BPF offload. Perf events can now be received on
packet data queues, which significantly improves the performance
(from total of 0.5 Msps to 5Msps per core). To get to this
performance we need a fast path for control messages which will
operate on raw buffers and recycle them immediately.
Patch 5 replaces the map pointers for perf maps with map IDs.
We look the pointers up in a hashtable, anyway, to validate they
are correct, so there is no performance difference. Map IDs
have the advantage of being easier to understand for users in
case of errors (we no longer print raw pointers to the logs).
Last patch improves info messages about map offload.
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
FW can put constraints on map element size to maximize resource
use and efficiency. When user attempts offload of a map which
does not fit into those constraints an informational message is
printed to kernel logs to inform user about the reason offload
failed. Map offload does not have access to any advanced error
reporting like verifier log or extack. There is also currently
no way for us to nicely expose the FW capabilities to user
space. Given all those constraints we should make sure log
messages are as informative as possible. Improve them.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Record perf maps by map ID, not raw kernel pointer. This helps
with debug messages, because printing pointers to logs is frowned
upon, and makes debug easier for the users, as map ID is something
they should be more familiar with. Note that perf maps are offload
neutral, therefore IDs won't be orphaned.
While at it use a rate limited print helper for the error message.
Reported-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Control queue is fairly low latency, and requires SKB allocations,
which means we can't even reach 0.5Msps with perf events. Allow
perf events to be delivered to data queues. This allows us to not
only use multiple queues, but also receive and deliver to user space
more than 5Msps per queue (Xeon E5-2630 v4 2.20GHz, no retpolines).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
In preparation for SKB-less perf event handling make
nfp_bpf_event_output() take buffer address and length,
not SKB as parameters.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Port id 0xffffffff is reserved for control messages. Allow reception
of messages with this id on data queues. Hand off a raw buffer to
the higher layer code, without allocating SKB for max efficiency.
The RX handle can't modify or keep the buffer, after it returns
buffer is handed back over to the NIC RX free buffer list.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Representor packets are received on PF queues with special metadata tag
for demux. There is no reason to resolve the representor ID -> netdev
after the skb has been allocated. Move the code, this will allow us to
handle special FW messages without SKB allocation overhead.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
net/xfrm/xfrm_interface.c:692:1-3: WARNING: PTR_ERR_OR_ZERO can be used
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Generated by: scripts/coccinelle/api/ptr_ret.cocci
Fixes: 44e2b838c24d ("xfrm: Return detailed errors from xfrmi_newlink")
CC: Benedict Wong <benedictwong@google.com>
Signed-off-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5e-updates-2018-07-26 (XDP redirect)
This series from Tariq adds the support for device-out XDP redirect.
Start with a simple RX and XDP cleanups:
- Replace call to MPWQE free with dealloc in interface down flow
- Do not recycle RX pages in interface down flow
- Gather all XDP pre-requisite checks in a single function
- Restrict the combination of large MTU and XDP
Since now XDP logic is going to be called from TX side as well,
generic XDP TX logic is not RX only anymore, for that Tariq creates
a new xdp.c file and moves XDP related code into it, and generalizes
the code to support XDP TX for XDP redirect, such as the xdp tx sq
structures and xdp counters.
XDP redirect support:
Add implementation for the ndo_xdp_xmit callback.
Dedicate a new set of XDP-SQ instances to satisfy the XDP_REDIRECT
requests. These instances are totally separated from the existing
XDP-SQ objects that satisfy local XDP_TX actions.
Performance tests:
xdp_redirect_map from ConnectX-5 to ConnectX-5.
CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz
Packet-rate of 64B packets.
Single queue: 7 Mpps.
Multi queue: 55 Mpps.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
UBSAN triggers the following undefined behaviour warnings:
[...]
[ 13.236124] UBSAN: Undefined behaviour in drivers/net/ethernet/amazon/ena/ena_eth_com.c:468:22
[ 13.240043] shift exponent 64 is too large for 64-bit type 'long long unsigned int'
[...]
[ 13.744769] UBSAN: Undefined behaviour in drivers/net/ethernet/amazon/ena/ena_eth_com.c:373:4
[ 13.748694] shift exponent 64 is too large for 64-bit type 'long long unsigned int'
[...]
When splitting the address to high and low, GENMASK_ULL is used to generate
a bitmask with dma_addr_bits field from io_sq (in ena_com_prepare_tx and
ena_com_add_single_rx_desc).
The problem is that dma_addr_bits is not initialized with a proper value
(besides being cleared in ena_com_create_io_queue).
Assign dma_addr_bits the correct value that is stored in ena_dev when
initializing the SQ.
Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Gal Pressman <pressmangal@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The root directories of netdevsim should only be used by the core
to create per-device subdirectories, so limit their visibility to
the core file.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tobin C. Harding says:
====================
docs: net: Convert netdev-FAQ to RST
Jon answered all the tree questions on v1 so if you will please take
this through your tree that would be awesome.
v2:
- Fix typo 'canonical_path_format' (thanks Edward)
- Add patch fixing references netdev-FAQ
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
File 'Documentation/networking/netdev-FAQ.txt' has been converted to RST
format. We should update all links/references to point to the new file.
Update references to netdev-FAQ
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Preferred kernel docs format is now restructured text. Convert
netdev-FAQ.txt to restructured text.
- Add SPDX license identifier.
- Change file heading 'Information you need to know about netdev' to
'netdev FAQ' to better suit displayed index (in HTML).
- Change question/answer layout to suit rst. Copy format in
Documentation/bpf/bpf_devel_QA.rst
- Fix indentation of code snippets
- If multiple consecutive URLs appear put them in a list (to maintain
whitespace).
- Use uniform spelling of 'bug fix' throughout document (not bugfix or
bug-fix).
- Add double back ticks to 'net' and 'net-next' when referring to the
trees.
- Use rst references for Documentation/ links.
- Add rst label 'netdev-FAQ' for referencing by other docs files.
- Remove stale entry from Documentation/networking/00-INDEX
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation to convert Documentation/network/netdev-FAQ.rst to
restructured text format. We would like to be able to reference 'the
canonical patch format' section.
Add rest label: 'the_canonical_patch_format'.
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
