| Age | Commit message (Collapse) | Author |
|---|
|
We don't need the BKL and now people will stop looking at this.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
The DMA channel status field was encoding redundant info wrt the DMA MMR
config register, and it was doing an incomplete job of checking all DMA
channels (some drivers write directly to the config register). So drop
the tristate field in favor of a binary atomic field. This simplifies
the code in general, removes the implicit need for sleeping, and forces
the suspend code to handle all channels properly.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
The driver was moved during the merge process, so update the defines to
match the new location.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Avoid including unnecessary headers all the time as well as circular
includes with core requirements.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
All the arches define a helper macro to make things easy for driver code.
Reported-by: Frank Van Hooft <frank@frankvh.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
The GPIOs on ports C/D/E on the BF538/BF539 do not behave the same way as
the other ports on the part and the same way as all other Blackfin parts.
The MMRs are programmed slightly different and they cannot be used to
generate interrupts or wakeup a sleeping system. Since these guys don't
fit into the existing code, create a simple gpiolib driver for them.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Have the C API trace funcs match the assembly API trace funcs.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
PLL_LOCKCNT applies only to the PLL programming sequence which does not
apply to core and system clock dividers. Writes to PLL_DIV to change the
CSEL/SSEL dividers take effect immediately.
There is still overhead in software in writing the new dividers, so just
use a value of 50us as this should be good enough.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Drop the CONFIG_USB_ISP1362_BFIN_GPIO_IRQ Kconfig as it never made it into
mainline and it was a bad interface into the board resources. For boards
that actually used this, replace it with an actual IRQ define. For boards
that didn't, simply drop the resources.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Since the link sizes never change at runtime, push the calculation out to
the linker script to save some useless calculation costs.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
The access_ok() function did not accept ranges within the async banks
which made it impossible to do XIP in flash. Fixing that also showed
that the current bfin_mem_access_type() code did not work with accesses
that spanned async banks (like a file system). So split out and fix the
async bank checks so that all these scenarios work as expected.
Signed-off-by: Bernd Schmidt <bernds_cb1@t-online.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Rather than using our own data structures that basically boil down to a
bitmap, use the standard bitmap functions.
Reported-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Now that the driver has been updated, convert the board resources to the
new i2c framework for managing slaves.
For boards that don't actually hook up to this hardware, simply drop the
resources altogether.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
The requested peripheral is turned into an index into some state arrays,
so make sure the calculated index doesn't exceed the index. This occurs
when using bogus pin values or the define headers are screwed up. Now
we'll notice right away that something needs fixing instead of trying to
track down random memory corruption.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
No point in redefining things that common code already does for us. Also
use CYC2NS_SCALE_FACTOR to better reflect reality and for better precision.
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Currently sched_clock() is only defined when using CYCLES as a clock
source. Declare sched_clock() in common code and mark it with notrace to
prevent invoking sched_clock() recursively (because ftrace uses
sched_clock() to record time).
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Some of the clocksource prototypes were updated, but the gptimer0 func was
missed in the process. Not a big issue as the argument is ignored, but we
should fix the compile warning anyways.
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Harald Krapfenbauer <Harald.Krapfenbauer@bluetechnix.at>
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
The Blackfin port only implemented an optimized version of the
csum_tcpudp_nofold function, so convert everything else to the new
generic code.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Convert the old xfs tracing support that could only be used with the
out of tree kdb and xfsidbg patches to use the generic event tracer.
To use it make sure CONFIG_EVENT_TRACING is enabled and then enable
all xfs trace channels by:
echo 1 > /sys/kernel/debug/tracing/events/xfs/enable
or alternatively enable single events by just doing the same in one
event subdirectory, e.g.
echo 1 > /sys/kernel/debug/tracing/events/xfs/xfs_ihold/enable
or set more complex filters, etc. In Documentation/trace/events.txt
all this is desctribed in more detail. To reads the events do a
cat /sys/kernel/debug/tracing/trace
Compared to the last posting this patch converts the tracing mostly to
the one tracepoint per callsite model that other users of the new
tracing facility also employ. This allows a very fine-grained control
of the tracing, a cleaner output of the traces and also enables the
perf tool to use each tracepoint as a virtual performance counter,
allowing us to e.g. count how often certain workloads git various
spots in XFS. Take a look at
http://lwn.net/Articles/346470/
for some examples.
Also the btree tracing isn't included at all yet, as it will require
additional core tracing features not in mainline yet, I plan to
deliver it later.
And the really nice thing about this patch is that it actually removes
many lines of code while adding this nice functionality:
fs/xfs/Makefile | 8
fs/xfs/linux-2.6/xfs_acl.c | 1
fs/xfs/linux-2.6/xfs_aops.c | 52 -
fs/xfs/linux-2.6/xfs_aops.h | 2
fs/xfs/linux-2.6/xfs_buf.c | 117 +--
fs/xfs/linux-2.6/xfs_buf.h | 33
fs/xfs/linux-2.6/xfs_fs_subr.c | 3
fs/xfs/linux-2.6/xfs_ioctl.c | 1
fs/xfs/linux-2.6/xfs_ioctl32.c | 1
fs/xfs/linux-2.6/xfs_iops.c | 1
fs/xfs/linux-2.6/xfs_linux.h | 1
fs/xfs/linux-2.6/xfs_lrw.c | 87 --
fs/xfs/linux-2.6/xfs_lrw.h | 45 -
fs/xfs/linux-2.6/xfs_super.c | 104 ---
fs/xfs/linux-2.6/xfs_super.h | 7
fs/xfs/linux-2.6/xfs_sync.c | 1
fs/xfs/linux-2.6/xfs_trace.c | 75 ++
fs/xfs/linux-2.6/xfs_trace.h | 1369 +++++++++++++++++++++++++++++++++++++++++
fs/xfs/linux-2.6/xfs_vnode.h | 4
fs/xfs/quota/xfs_dquot.c | 110 ---
fs/xfs/quota/xfs_dquot.h | 21
fs/xfs/quota/xfs_qm.c | 40 -
fs/xfs/quota/xfs_qm_syscalls.c | 4
fs/xfs/support/ktrace.c | 323 ---------
fs/xfs/support/ktrace.h | 85 --
fs/xfs/xfs.h | 16
fs/xfs/xfs_ag.h | 14
fs/xfs/xfs_alloc.c | 230 +-----
fs/xfs/xfs_alloc.h | 27
fs/xfs/xfs_alloc_btree.c | 1
fs/xfs/xfs_attr.c | 107 ---
fs/xfs/xfs_attr.h | 10
fs/xfs/xfs_attr_leaf.c | 14
fs/xfs/xfs_attr_sf.h | 40 -
fs/xfs/xfs_bmap.c | 507 +++------------
fs/xfs/xfs_bmap.h | 49 -
fs/xfs/xfs_bmap_btree.c | 6
fs/xfs/xfs_btree.c | 5
fs/xfs/xfs_btree_trace.h | 17
fs/xfs/xfs_buf_item.c | 87 --
fs/xfs/xfs_buf_item.h | 20
fs/xfs/xfs_da_btree.c | 3
fs/xfs/xfs_da_btree.h | 7
fs/xfs/xfs_dfrag.c | 2
fs/xfs/xfs_dir2.c | 8
fs/xfs/xfs_dir2_block.c | 20
fs/xfs/xfs_dir2_leaf.c | 21
fs/xfs/xfs_dir2_node.c | 27
fs/xfs/xfs_dir2_sf.c | 26
fs/xfs/xfs_dir2_trace.c | 216 ------
fs/xfs/xfs_dir2_trace.h | 72 --
fs/xfs/xfs_filestream.c | 8
fs/xfs/xfs_fsops.c | 2
fs/xfs/xfs_iget.c | 111 ---
fs/xfs/xfs_inode.c | 67 --
fs/xfs/xfs_inode.h | 76 --
fs/xfs/xfs_inode_item.c | 5
fs/xfs/xfs_iomap.c | 85 --
fs/xfs/xfs_iomap.h | 8
fs/xfs/xfs_log.c | 181 +----
fs/xfs/xfs_log_priv.h | 20
fs/xfs/xfs_log_recover.c | 1
fs/xfs/xfs_mount.c | 2
fs/xfs/xfs_quota.h | 8
fs/xfs/xfs_rename.c | 1
fs/xfs/xfs_rtalloc.c | 1
fs/xfs/xfs_rw.c | 3
fs/xfs/xfs_trans.h | 47 +
fs/xfs/xfs_trans_buf.c | 62 -
fs/xfs/xfs_vnodeops.c | 8
70 files changed, 2151 insertions(+), 2592 deletions(-)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
|
|
Change the xfs_iext_insert / xfs_iext_remove prototypes to pass more
information which will allow pushing the trace points from the callers
into those functions. This includes folding the whichfork information
into the state variable to minimize the addition stack footprint.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
|
|
Cleanup the extent state macros in the bmap code to use one common set of
flags that we can pass to the tracing code later and remove a lot of the
macro obsfucation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
|
|
This patch adds MSIOF and mmc_spi platform data for
the CN11 port on the SuperH Ecovec24 board. No card
detect interrupt is available so the MMC code is
configured to poll. The WP signal is implemented
together with CD and power control. The board only
supports 3.3V power.
The platform data is wrapped in SDHI #ifdefs to
allow both the SDHI and the MSIOF to coexist. Only
one configuration is allowed at a time. The pin
routing is selected by a dip switch but we can
unfortunately not detect this setting at run time.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6
|
|
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
After the recent FPU optimisation commit the signature of save_fpu()
changed. "regs" wasn't used in the implementation of save_fpu() anyway.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Now when the sh-sci driver can do early serial output,
get rid of the old duplicated code. This patch is V2 and
removes support for "earlyprintk=serial" together with
the following kconfig options:
CONFIG_EARLY_SCIF_CONSOLE
CONFIG_EARLY_SCIF_CONSOLE_PORT
CONFIG_EARLY_PRINTK
With this patch applied "earlyprintk=" support is always
built-in the SuperH kernel. For this to work the serial
driver must have early platform support and in the case
of sh-sci the serial console needs to be enabled:
CONFIG_SERIAL_SH_SCI_CONSOLE=y
So after enabling the SuperH SCI console kconfig option
you also need to point out port using the kernel command
line: "earlyprintk=sh-sci.N[,baudrate][,keep]"
Remember that clocks may be disabled by the boot loader
so you may have to do some board specific static clock
setup before earlyprintk will work on your platform.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch breaks out the sh5 scif serial port platform
data from a shared platform device to one platform
device per port. Also, move the serial port to the list
of early platform devices.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch breaks out the sh4a scif serial port platform
data from a shared platform device to one platform
device per port. Also, add serial ports to the list of
early platform devices.
All sh4a except SuperH Mobile processors are modified by
this patch.
While at it, sh7757 gets early platform device support.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch breaks out the sh4a scif serial port platform
data from a shared platform device to one platform
device per port. Also, add serial ports to the list of
early platform devices.
Only sh4a SuperH Mobile processors are modified by this
patch.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch breaks out the sh4 scif serial port platform
data from a shared platform device to one platform
device per port. Also, add serial ports to the list of
early platform devices.
While at it, get rid of the R2D ifdef in the processor
code and adjust the defconfigs to use ttySC1.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch breaks out the sh3 scif serial port platform
data from a shared platform device to one platform
device per port. Also, add serial ports to the list of
early platform devices.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch breaks out the sh2a scif serial port platform
data from a shared platform device to one platform
device per port. Also, add serial ports to the list of
early platform devices.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch breaks out the sh2 scif serial port platform
data from a shared platform device to one platform
device per port. Also, add serial ports to the list of
early platform devices.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This is V2 of early serial console support for the sh-sci
driver. The early serial console is using early platform
devices and "earlyprintk". To use this feature the early
platform devices must be broken out to one device per port
and the desired port should be selected on the kernel command
line like: "earlyprintk=sh-sci.N[,baudrate][,keep]"
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Currently, ARB_DISABLE is a NOP on all of the recent Intel platforms.
For such platforms, reduce contention on c3_lock by skipping the fake
ARB_DISABLE.
The cpu model id on one laptop is 14. If we disable ARB_DISABLE on this box,
the box can't be booted correctly. But if we still enable ARB_DISABLE on this
box, the box can be booted correctly.
So we still use the ARB_DISABLE for the cpu which mode id is less than 0x0f.
http://bugzilla.kernel.org/show_bug.cgi?id=14700
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Acked-by: Pallipadi, Venkatesh <venkatesh.pallipadi@intel.com>
cc: stable@kernel.org
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
When switching to request_firmware() to load the context programs,
some endian fixes need to be applied. This makes it work again on
my quad g5 nvidia 6600.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
drivers/pci/dmar.c uses these functions, so provide them for ia64
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
SPIN_LOCK_UNLOCKED is deprecated. Use __SPIN_LOCK_UNLOCKED instead.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-ia64@vger.kernel.org
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
It's possible that SBA IOMMU might fail to find I/O space under heavy
I/Os. SBA IOMMU panics on allocation failure but it shouldn't; drivers
can handle the failure. The majority of other IOMMU drivers don't panic
on allocation failure.
This patch fixes SBA IOMMU path to handle allocation failure properly.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
This is a patch related to this discussion.
http://www.spinics.net/lists/linux-ia64/msg07605.html
When INIT is sent, ip/psr/pfs register is stored to the I-resources
(iip/ipsr/ifs registers), and they are copied in the min-state save
area(pmsa_{iip,ipsr,ifs}).
Therefore, in creating pt_regs at ia64_mca_modify_original_stack(),
cr_{iip,ipsr,ifs} should be derived from pmsa_{iip,ipsr,ifs}. But
current code copies pmsa_{xip,xpsr,xfs} to cr_{iip,ipsr,ifs}
when PSR.ic is 0.
finish_pt_regs(struct pt_regs *regs, const pal_min_state_area_t *ms,
unsigned long *nat)
{
(snip)
if (ia64_psr(regs)->ic) {
regs->cr_iip = ms->pmsa_iip;
regs->cr_ipsr = ms->pmsa_ipsr;
regs->cr_ifs = ms->pmsa_ifs;
} else {
regs->cr_iip = ms->pmsa_xip;
regs->cr_ipsr = ms->pmsa_xpsr;
regs->cr_ifs = ms->pmsa_xfs;
}
It's ok when PSR.ic is not 0. But when PSR.ic is 0, this could be
a problem when we investigate kernel as the value of regs->cr_iip does
not point to where INIT really interrupted.
At first I tried to change finish_pt_regs() so that it uses always
pmsa_{iip,ipsr,ifs} for cr_{iip,ipsr,ifs}, but Keith Owens pointed out
it could cause another problem if I change it.
>The only problem I can think of is an MCA/INIT
>arriving while code like SAVE_MIN or SAVE_REST is executing. Back
>tracing at that point using pmsa_iip is going to be a problem, you have
>no idea what state the registers or stack are in.
I confirmed he was right, so I decided to keep it as-is and to
save pmsa_{iip,ipsr,ifs} to ia64_sal_os_state for debugging.
An attached patch is just adding new members into ia64_sal_os_state to
save pmsa_{iip,ipsr,ifs}.
Signed-off-by: Takao Indoh <indou.takao@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
This was an oversight; it should be among the export flags that can be
allowed to vary by pseudoflavor. This allows an administrator to (for
example) allow auth_sys mounts only from low ports, but allow auth_krb5
mounts to use any port.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
|
|
Previously, we tried to use IA64_DEF_FIRST_DEVICE_VECTOR (0x30) as the
IA64_IRQ_MOVE_VECTOR. However, we allocate other IRQs from the device
vector range, so there's no guarantee that IA64_DEF_FIRST_DEVICE_VECTOR
will still be available when we register IA64_IRQ_MOVE_VECTOR.
This patch statically allocates 0x30 for IA64_IRQ_MOVE_VECTOR and
removes it from the device vector range.
Without this patch, we crash on machines like the HP rx3600 that use
vector 48 (0x30) as the ACPI SCI interrupt:
kernel BUG at arch/ia64/kernel/irq_ia64.c:647!
swapper[0]: bugcheck! 0 [1]
Modules linked in:
Pid: 0, CPU 0, comm: swapper
psr : 00001010084a2018 ifs : 800000000000030e ip : [<a000000100012ed0>] Not tainted (2.6.32-rc8-00184-gd5d4ec8)
ip is at ia64_native_register_percpu_irq+0x110/0x1e0
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Tested-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Tested-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
Soon we will add the new V4ROOT flag, and allow the INSECURE flag to
vary by pseudoflavor. It would be useful for nfs-utils (for example,
for improved exportfs error reporting) to be able to know when this
happens. Use this new interface for that purpose.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
|
|
The ch7006 driver could be built even when nouveau was not enabled,
but the build fails in that case, so make it depend on DRM_NOUVEUA.
Also make the I2c encoder/helper chips menu depend on I2C (no build
error, just visual inspection).
ERROR: "drm_helper_probe_single_connector_modes" [drivers/gpu/drm/i2c/ch7006.ko] undefined!
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
Lots of include/linux/nfsd/* headers are only used by
nfsd module. Move them to the source directory
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
|
