| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Few fixes for omaps to allow am437x only builds to boot properly with
CPU_IDLE and ARM TWD timer. This is probably a common configuration setup
for people making products with these SoCs so let's make sure it works.
Also a wakeirq fix for duovero parlor making my life a bit easier as that
allows me to run basic PM regression tests on it.
It would be nice to have these in v4.4, but if it gets too late for that
because of the holidays, it is not super critical if these get merged for
v4.5.
* tag 'omap-for-v4.4/fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Fix UART wakeirq for omap4 duovero parlor
ARM: OMAP2+: AM43xx: select ARM TWD timer
ARM: OMAP2+: am43xx: enable GENERIC_CLOCKEVENTS_BROADCAST
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
The i.MX fixes for 4.4, 3rd round:
- Fix Ethernet PHY mode on i.MX6 Ventana boards, which can result in
a non-functional Ethernet when Marvell phy driver rather than generic
phy driver is selected.
- Fix an assigned-clock configuration bug on imx6qdl-sabreauto board
which was introduced by commit ed339363de1b ("ARM: dts:
imx6qdl-sabreauto: Allow HDMI and LVDS to work simultaneously").
* tag 'imx-fixes-4.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6: Fix Ethernet PHY mode on Ventana boards
ARM: dts: imx: Fix the assigned-clock mismatch issue on imx6q/dl
|
|
0x4e is the runtime address normally associated with perihperal ICs.
0x45 is not a valid runtime address.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The primary PMICs use 0x3a3 as their hardware address, not 0x3e3.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Looks like we're missing the wakeirq for the console uart for
duovero parlor. Let's add that as without it console acess just
hangs with PM enabled.
Cc: Arun Bharadwaj <arun@gumstix.com>
Cc: Ash Charles <ash@gumstix.com>
Cc: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Make sure to tell the kernel that AM437x devices have ARM TWD timer.
Signed-off-by: Felipe Balbi <balbi@ti.com>
[grygorii.strashko@ti.com: drop ARM Global timer selection, because
it's incompatible with PM (cpuidle/cpufreq). So, it's unsafe to enable
it unconditionally]
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
System will misbehave in the following case:
- AM43XX only build (UP);
- CONFIG_CPU_IDLE=y
- ARM TWD timer enabled and selected as clockevent device.
In the above case, It's expected that broadcast timer will be used as
backup timer when CPUIdle will put MPU in low power states where ARM
TWD will stop and lose its context. But, the CONFIG_SMP might not be
selected when kernel is built for AM43XX SoC only and, as result,
GENERIC_CLOCKEVENTS_BROADCAST option will not be selected also. This
will break CPUIdle and System will stuck in low power states.
Hence, fix it by selecting GENERIC_CLOCKEVENTS_BROADCAST option for
AM43XX SoCs always and add empty tick_broadcast() function
implementation - no need to send any IPI on UP. After this change
timer1 will be selected as broadcast timer the same way as for SMP,
and CPUIdle will work properly.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Need to include sched.h to fix the following compilation error
if FSL_IFC is enabled on ARM64 machine.
In file included from include/linux/mmzone.h:9:0,
from include/linux/gfp.h:5,
from include/linux/kmod.h:22,
from include/linux/module.h:13,
from drivers/memory/fsl_ifc.c:22:
drivers/memory/fsl_ifc.c: In function ‘check_nand_stat’:
include/linux/wait.h:165:35: error: ‘TASK_NORMAL’ undeclared (first use in this function)
#define wake_up(x) __wake_up(x, TASK_NORMAL, 1, NULL)
^
drivers/memory/fsl_ifc.c:136:3: note: in expansion of macro ‘wake_up’
wake_up(&ctrl->nand_wait);
^
include/linux/wait.h:165:35: note: each undeclared identifier is reported only once for each function it appears in
#define wake_up(x) __wake_up(x, TASK_NORMAL, 1, NULL)
^
drivers/memory/fsl_ifc.c:136:3: note: in expansion of macro ‘wake_up’
wake_up(&ctrl->nand_wait);
^
Analysis is as follows:
I put some instrumental code and get the
following .h files inclusion sequence:
In file included from ./arch/arm64/include/asm/compat.h:25:0,
from ./arch/arm64/include/asm/stat.h:23,
from include/linux/stat.h:5,
from include/linux/module.h:10,
from drivers/memory/fsl_ifc.c:23:
include/linux/sched.h:113:1: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘struct’
struct sched_attr {
^
CONFIG_COMPAT=y is enabled while 39 and 48 bit VA is selected.
When 42 bit VA is selected, it does not enable CONFIG_COMPAT=y
In ./arch/arm64/include/asm/stat.h:23, it has
"#ifdef CONFIG_COMPAT"
"#include <asm/compat.h>"
"..."
"#endif"
Since ./arch/arm64/include/asm/stat.h does not
include ./arch/arm64/include/asm/compat.h,
then it will not include include/linux/sched.h
Hence we have to manually add "#include <linux/sched.h>"
in drivers/memory/fsl_ifc.c
Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Gateworks Ventana boards seem to need "RGMII-ID" (internal delay)
PHY mode, instead of simple "RGMII", for their Marvell 88E1510
transceiver. Otherwise, the Ethernet MAC doesn't work with Marvell PHY
driver (TX doesn't seem to work correctly).
Tested on GW5400 rev. C.
This bug affects ARM Fedora 23.
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The 'assigned-clock-parents' and 'assigned-clock-rates' list
should corresponding to the 'assigned-clocks' property clock list.
Signed-off-by: Bai Ping <b51503@freescale.com>
Fixes: ed339363de1b ("ARM: dts: imx6qdl-sabreauto: Allow HDMI and LVDS to work simultaneously")
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes
Merge "Allwinner fixes for 4.4" from Maxime Ripard:
Allwinner fixes for 4.4
Two patches, one to fix the touchscreen axis on one Allwinner board, and
the other one fixing a mutex unlocking issue on one error path in the RSB
driver.
* tag 'sunxi-fixes-for-4.4' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
bus: sunxi-rsb: unlock on error in sunxi_rsb_read()
ARM: dts: sunxi: sun6i-a31s-primo81.dts: add touchscreen axis swapping property
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
Merge "ARM: imx: fixes for 4.4, 2nd round" from Shawn Guo:
The i.MX fixes for 4.4, 2nd round:
- Fix vf610 SAI clock configuration bug which is discovered by the newly
added master mode support in SAI audio driver.
- Fix buggy L2 cache latency values in vf610 device trees, which may
cause system hang when cpu runs at a higher frequency.
* tag 'imx-fixes-4.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: vf610: use reset values for L2 cache latencies
ARM: dts: vf610: fix clock definition for SAI2
ARM: imx: clk-vf610: fix SAI clock tree
|
|
The GPIO block for ls2080a platform has little endian registers,
the GPIO driver needs this property to read/write registers by
right interface.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
|
|
The GPIO block on different QorIQ chips could have registers in different
endianess. Define the property to specify which endian is used by the
hardware.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
|
|
Add the "little-endian" property to fix the issue that eSDHC
is not working and dumping out "mmc0: Controller never released
inhibit bit(s)." error messages constantly.
Fixes: 5461597f6ce0 ("dts/ls2080a: Update DTSI to add support of various peripherals")
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
|
|
Linux on Vybrid used several different L2 latencies so far, none
of them seem to be the right ones. According to the application note
AN4947 ("Understanding Vybrid Architecture"), the tag portion runs
on CPU clock and is inside the L2 cache controller, whereas the data
portion is stored in the external SRAM running on platform clock.
Hence it is likely that the correct value requires a higher data
latency then tag latency.
These are the values which have been used so far:
- The mainline values:
arm,data-latency = <1 1 1>;
arm,tag-latency = <2 2 2>;
Those values have lead to problems on higher clocks. They look
like a poor translation from the reset values (missing +1 offset
and a mix up between tag/latency values).
- The Linux 3.0 (SoC vendor BSP) values (converted to DT notation):
arm,data-latency = <4 2 3>
arm,tag-latency = <4 2 3>
The cache initialization function along with the value matches the
i.MX6 code from the same kernel, so it seems that those values have
just been copied.
- The Colibri values:
arm,data-latency = <2 1 2>;
arm,tag-latency = <3 2 3>;
Those were a mix between the values of the Linux 3.0 based BSP and
the mainline values above.
- The SoC Reset values (converted to DT notation):
arm,data-latency = <3 3 3>;
arm,tag-latency = <2 2 2>;
So far there is no official statement on what the correct values are.
See also the related Freescale community thread:
https://community.freescale.com/message/579785#579785
For now, the reset values seem to be the best bet. Remove all other
"bogus" values and use the reset value on vf610.dtsi level.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "omap fixes against v4.4-rc4" from Tony Lindgren
Few fixes for omaps for v4.4-rc cycle:
- Fix clock source for ARM TWD and global timers on am437x
- Always select REGULATOR_FIXED_VOLTAGE for omap2+ instead of
when MACH_OMAP3_PANDORA is selected
- Fix SPI DMA handles for dm816x as only some were mapped
- Fix up mbox cells for dm816x to make mailbox usable
* tag 'omap-for-v4.4/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am4372: fix clock source for arm twd and global timers
ARM: OMAP2+: enable REGULATOR_FIXED_VOLTAGE
ARM: dts: add dm816x missing spi DT dma handles
ARM: dts: add dm816x missing #mbox-cells
|
|
The recent change to use a pwm lookup table for the ezx machines
was incomplete and only changed the a780 model, but not the
other ones in the same file.
This adds the missing calls to pwm_add_table().
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: c3322022897c ("ARM: pxa: ezx: Use PWM lookup table")
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
|
|
git://git.infradead.org/users/hesselba/linux-berlin into fixes
Merge "Marvell Berlin fixes for 4.4-rc1 (round 1)" from Sebastian Hesselbarth:
- fix wrong SDIO DT clocks on BG2Q
* tag 'berlin-fixes-for-4.4-rc1-1' of git://git.infradead.org/users/hesselba/linux-berlin:
ARM: dts: berlin: add 2nd clock for BG2Q sdhci0 and sdhci1
ARM: dts: berlin: correct BG2Q's sdhci2 2nd clock
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into fixes
Merge "Second fixes for 4.4" from Alexandre Belloni:
- fix of a hardware setup that prevents the sd/mmc interface to show up on
sama5d2.
- proper selection of pinctrl drivers. PIO4 is necessary for the sama5d2 to
boot.
* tag 'at91-4.4-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: at91: fix pinctrl driver selection
ARM: at91/dt: add always-on to 1.8V regulator
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into fixes
Merge "Fixes for Exynos" from Krzysztof Kozlowski:
1. Fix potential NULL pointer dereference in Exynos PMU driver.
2. Remove incorrect __init annotation from s3c24xx cpufreq driver
structures.
* tag 'samsung-fixes-4.4' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
cpufreq: s3c24xx: Do not mark s3c2410_plls_add as __init
ARM: EXYNOS: Fix potential NULL pointer access in exynos_sys_powerdown_conf
|
|
We removed CLK_IGNORE_UNUSED from CLKID_SDIO's flag, so the sdhci0 and
sdhci1 don't work. We fix this by adding the optional 2nd clock for
BG2Q's sdhci0 and sdhci1. This patch brings another benefit: the 2nd
clock can be disabled during runtime pm, so saves power a bit.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
|
|
The optional 2nd clock is CLKID_SDIO. We removed CLK_IGNORE_UNUSED
from CLKID_SDIO's flag, so the sdhci2 doesn't work. This patch fixes
this issue by correcting the sdhci2's 2nd clock.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
|
|
ARM TWD and Global timer are clocked by PERIPHCLK which is MPU_CLK/2.
But now they are clocked by dpll_mpu_m2_ck == MPU_CLK and, as result.
Timekeeping core misbehaves. For example, execution of command
"sleep 5" will take 10 sec instead of 5.
Hence, fix it by adding mpu_periphclk ("fixed-factor-clock") and use
it for clocking ARM TWD and Global timer (same way as on OMAP4).
Cc: Tony Lindgren <tony@atomide.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Fixes:commit 8cbd4c2f6a99 ("arm: boot: dts: am4372: add ARM timers and SCU nodes")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Move the selection of the pinctrl driver to SoC family level since we
have two pinctrl drivers. It is useless to select one which is not
compatible with the SoC.
[abelloni: fixed pm.c when only sama2d2 is selected]
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
As the SDHCI controller needs the 1.8V line to be always enabled for some eMMC
configurations, set the proper "regulator-always-on" property to the board DTS
files.
Note that the sdhci classical regulator definitions doesn't suit our controller
for this 1.8V purpose.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
So far, only the bus clock has been assigned, but in reality the
SAI IP has for clock inputs. The driver has been updated to
make use of the additional clock inputs by c3ecef21c3f2 ("ASoC:
fsl_sai: add sai master mode support"). Due to a bug in the
clock tree, the audio clock has been enabled none the less by
the specified bus clock (see "ARM: imx: clk-vf610: fix SAI
clock tree"), which made master mode even without the proper
clock assigned working.
This patch completes the clock definition for SAI2. On Vybrid,
only two MCLK out of the four options are available (the first
being the bus clock itself). See chapter 8.10.1.2.3 of the
Vybrid Reference manual ("SAI transmitter and receiver options
for MCLK selection"). Note: The audio clocks are only required
in master mode.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The Synchronous Audio Interface (SAI) instances are clocked by
independent clocks: The bus clock and the audio clock (as shown in
Figure 51-1 in the Vybrid Reference Manual). The clock gates in
CCGR0/CCGR1 for SAI0 through SAI3 are bus clock gates, as access
tests to the registers with/without gating those clocks have shown.
The audio clock is gated by the SAIx_EN gates in CCM_CSCDR1,
followed by a clock divider (SAIx_DIV). Currently, the parent of
the bus clock gates has been assigned to SAIx_DIV, which is not
involved in the bus clock path for the SAI instances (see chapter
9.10.12, SAI clocking in the Vybrid Reference Manual).
Fix this by define the parent clock of VF610_CLK_SAIx to be the bus
clock.
If the driver needs the audio clock (when used in master mode), a
fixed device tree is required which assign the audio clock properly
to VF610_CLK_SAIx_DIV.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
On ixp4xx, the readl() function returns an 'unsigned long' output
when indirect I/O is used. This is unlike any other platform, and
it causes lots of harmless compiler warnings, such as:
drivers/ata/libahci.c: In function 'ahci_show_host_version':
drivers/ata/libahci.c:254:22: warning: format '%x' expects argument of type 'unsigned int', but argument 3 has type 'long unsigned int' [-Wformat=]
drivers/block/mtip32xx/mtip32xx.c: In function 'mtip_hw_read_registers':
drivers/block/mtip32xx/mtip32xx.c:2602:31: warning: format '%X' expects argument of type 'unsigned int', but argument 3 has type 'long unsigned int' [-Wformat=]
drivers/block/cciss.c: In function 'print_cfg_table':
drivers/block/cciss.c:3845:25: warning: format '%d' expects argument of type 'int', but argument 4 has type 'long unsigned int' [-Wformat=]
This changes all six of the ixp4xx specific I/O read functions
to return the same types that we have in the normal asm/io.h,
to avoid the warnings.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Krzysztof Halasa <khalasa@piap.pl>
|
|
This patch is specifically for PCI support on the Versatile PB board using
a DT. Currently, the dynamic IRQ mapping is broken when using DTs. For
example, on QEMU, the SCSI driver is unable to request the IRQ. To fix
this issue, this patch replaces the current dynamic mechanism with a
static value as is done in the non-DT case.
Signed-off-by: Guillaume Delbergue <guillaume.delbergue@greensocs.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: stable@vger.kernel.org
|
|
Enable REGULATOR_FIXED_VOLTAGE for all OMAP2+ platforms
otherwise system can't boot from SD-card when kernel is
built for single SoC (for example, with CONFIG_SOC_DRA7XX=y only).
It's also required for almost all TI SoC's platforms.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add the missing SPI controller DMA handler in the dm816x DT
node, only properties for the two channels on four were present.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add missing #mbox-cells for dm816x mbox DT node.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
|
|
Pull nouveau and radeon fixes from Dave Airlie:
"Just some nouveau and radeon/amdgpu fixes.
The nouveau fixes look large as the firmware context files are
regenerated, but the actual change is quite small"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon: make some dpm errors debug only
drm/nouveau/volt/pwm/gk104: fix an off-by-one resulting in the voltage not being set
drm/nouveau/nvif: allow userspace access to its own client object
drm/nouveau/gr/gf100-: fix oops when calling zbc methods
drm/nouveau/gr/gf117-: assume no PPC if NV_PGRAPH_GPC_GPM_PD_PES_TPC_ID_MASK is zero
drm/nouveau/gr/gf117-: read NV_PGRAPH_GPC_GPM_PD_PES_TPC_ID_MASK from correct GPC
drm/nouveau/gr/gf100-: split out per-gpc address calculation macro
drm/nouveau/bios: return actual size of the buffer retrieved via _ROM
drm/nouveau/instmem: protect instobj list with a spinlock
drm/nouveau/pci: enable c800 magic for some unknown Samsung laptop
drm/nouveau/pci: enable c800 magic for Clevo P157SM
drm/radeon: make rv770_set_sw_state failures non-fatal
drm/amdgpu: move dependency handling out of atomic section v2
drm/amdgpu: optimize scheduler fence handling
drm/amdgpu: remove vm->mutex
drm/amdgpu: add mutex for ba_va->valids/invalids
drm/amdgpu: adapt vce session create interface changes
drm/amdgpu: vce use multiple cache surface starting from stoney
drm/amdgpu: reset vce trap interrupt flag
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC fixes from Alexandre Belloni:
"Two fixes for the ds1307 alarm and wakeup"
* tag 'rtc-4.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: ds1307: fix alarm reading at probe time
rtc: ds1307: fix kernel splat due to wakeup irq handling
|
|
Pull MIPS fix from Ralf Baechle:
"Just a fix for empty loops that may be removed by non-antique GCC"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Fix delay loops which may be removed by GCC.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k fixes from Geert Uytterhoeven:
"Summary:
- Add missing initialization of max_pfn, which is needed to make
selftests/vm/mlock2-tests succeed,
- Wire up new mlock2 syscall"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Wire up mlock2
m68knommu: Add missing initialization of max_pfn and {min,max}_low_pfn
m68k/mm: sun3 - Add missing initialization of max_pfn and {min,max}_low_pfn
m68k/mm: m54xx - Add missing initialization of max_pfn
m68k/mm: motorola - Add missing initialization of max_pfn
|
|
Pull ARM fixes from Russell King:
"Just two changes this time around:
- wire up the new mlock2 syscall added during the last merge window
- fix a build problem with certain configurations provoked by making
CONFIG_OF user selectable"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8454/1: OF implies OF_FLATTREE
ARM: wire up mlock2 syscall
|
|
Pull SCSI target fixes from Nicholas Bellinger:
- fix tcm-user backend driver expired cmd time processing (agrover)
- eliminate kref_put_spinlock_irqsave() for I/O completion (bart)
- fix iscsi login kthread failure case hung task regression (nab)
- fix COMPARE_AND_WRITE completion use-after-free race (nab)
- fix COMPARE_AND_WRITE with SCF_PASSTHROUGH_SG_TO_MEM_NOALLOC non zero
SGL offset data corruption. (Jan + Doug)
- fix >= v4.4-rc1 regression for tcm_qla2xxx enable configfs attribute
(Himanshu + HCH)
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target/stat: print full t10_wwn.model buffer
target: fix COMPARE_AND_WRITE non zero SGL offset data corruption
qla2xxx: Fix regression introduced by target configFS changes
kref: Remove kref_put_spinlock_irqsave()
target: Invoke release_cmd() callback without holding a spinlock
target: Fix race for SCF_COMPARE_AND_WRITE_POST checking
iscsi-target: Fix rx_login_comp hang after login failure
iscsi-target: return -ENOMEM instead of -1 in case of failed kmalloc()
target/user: Do not set unused fields in tcmu_ops
target/user: Fix time calc in expired cmd processing
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal management fixes from Zhang Rui:
"Specifics:
- several fixes and cleanups on Rockchip thermal drivers.
- add the missing support of RK3368 SoCs in Rockchip driver.
- small fixes on of-thermal, power_allocator, rcar driver, IMX, and
QCOM drivers, and also compilation fixes, on thermal.h, when thermal
is not selected"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
imx: thermal: use CPU temperature grade info for thresholds
thermal: fix thermal_zone_bind_cooling_device prototype
Revert "thermal: qcom_spmi: allow compile test"
thermal: rcar_thermal: remove redundant operation
thermal: of-thermal: Reduce log level for message when can't fine thermal zone
thermal: power_allocator: Use temperature reading from tz
thermal: rockchip: Support the RK3368 SoCs in thermal driver
thermal: rockchip: consistently use int for temperatures
thermal: rockchip: Add the sort mode for adc value increment or decrement
thermal: rockchip: improve the conversion function
thermal: rockchip: trivial: fix typo in commit
thermal: rockchip: better to compatible the driver for different SoCs
dt-bindings: rockchip-thermal: Support the RK3368 SoCs compatible
|
|
Cut 'n paste error saw it only process sizeof(t10_wwn.vendor) characters.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
target_core_sbc's compare_and_write functionality suffers from taking
data at the wrong memory location when writing a CAW request to disk
when a SGL offset is non-zero.
This can happen with loopback and vhost-scsi fabric drivers when
SCF_PASSTHROUGH_SG_TO_MEM_NOALLOC is used to map existing user-space
SGL memory into COMPARE_AND_WRITE READ/WRITE payload buffers.
Given the following sample LIO subtopology,
% targetcli ls /loopback/
o- loopback ................................. [1 Target]
o- naa.6001405ebb8df14a ....... [naa.60014059143ed2b3]
o- luns ................................... [2 LUNs]
o- lun0 ................ [iblock/ram0 (/dev/ram0)]
o- lun1 ................ [iblock/ram1 (/dev/ram1)]
% lsscsi -g
[3:0:1:0] disk LIO-ORG IBLOCK 4.0 /dev/sdc /dev/sg3
[3:0:1:1] disk LIO-ORG IBLOCK 4.0 /dev/sdd /dev/sg4
the following bug can be observed in Linux 4.3 and 4.4~rc1:
% perl -e 'print chr$_ for 0..255,reverse 0..255' >rand
% perl -e 'print "\0" x 512' >zero
% cat rand >/dev/sdd
% sg_compare_and_write -i rand -D zero --lba 0 /dev/sdd
% sg_compare_and_write -i zero -D rand --lba 0 /dev/sdd
Miscompare reported
% hexdump -Cn 512 /dev/sdd
00000000 0f 0e 0d 0c 0b 0a 09 08 07 06 05 04 03 02 01 00
00000010 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
*
00000200
Rather than writing all-zeroes as instructed with the -D file, it
corrupts the data in the sector by splicing some of the original
bytes in. The page of the first entry of cmd->t_data_sg includes the
CDB, and sg->offset is set to a position past the CDB. I presume that
sg->offset is also the right choice to use for subsequent sglist
members.
Signed-off-by: Jan Engelhardt <jengelh@netitwork.de>
Tested-by: Douglas Gilbert <dgilbert@interlog.com>
Cc: <stable@vger.kernel.org> # v3.12+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
this patch fixes following regression
# targetcli
[Errno 13] Permission denied: '/sys/kernel/config/target/qla2xxx/21:00:00:0e:1e:08:c7:20/tpgt_1/enable'
Fixes: 2eafd72939fd ("target: use per-attribute show and store methods")
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
The last user is gone. Hence remove this function.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch fixes the following kernel warning because it avoids that
IRQs are disabled while ft_release_cmd() is invoked (fc_seq_set_resp()
invokes spin_unlock_bh()):
WARNING: CPU: 3 PID: 117 at kernel/softirq.c:150 __local_bh_enable_ip+0xaa/0x110()
Call Trace:
[<ffffffff814f71eb>] dump_stack+0x4f/0x7b
[<ffffffff8105e56a>] warn_slowpath_common+0x8a/0xc0
[<ffffffff8105e65a>] warn_slowpath_null+0x1a/0x20
[<ffffffff81062b2a>] __local_bh_enable_ip+0xaa/0x110
[<ffffffff814ff229>] _raw_spin_unlock_bh+0x39/0x40
[<ffffffffa03a7f94>] fc_seq_set_resp+0xe4/0x100 [libfc]
[<ffffffffa02e604a>] ft_free_cmd+0x4a/0x90 [tcm_fc]
[<ffffffffa02e6972>] ft_release_cmd+0x12/0x20 [tcm_fc]
[<ffffffffa042bd66>] target_release_cmd_kref+0x56/0x90 [target_core_mod]
[<ffffffffa042caf0>] target_put_sess_cmd+0xc0/0x110 [target_core_mod]
[<ffffffffa042cb81>] transport_release_cmd+0x41/0x70 [target_core_mod]
[<ffffffffa042d975>] transport_generic_free_cmd+0x35/0x420 [target_core_mod]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Joern Engel <joern@logfs.org>
Reviewed-by: Andy Grover <agrover@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch addresses a race + use after free where the first
stage of COMPARE_AND_WRITE in compare_and_write_callback()
is rescheduled after the backend sends the secondary WRITE,
resulting in second stage compare_and_write_post() callback
completing in target_complete_ok_work() before the first
can return.
Because current code depends on checking se_cmd->se_cmd_flags
after return from se_cmd->transport_complete_callback(),
this results in first stage having SCF_COMPARE_AND_WRITE_POST
set, which incorrectly falls through into second stage CAW
processing code, eventually triggering a NULL pointer
dereference due to use after free.
To address this bug, pass in a new *post_ret parameter into
se_cmd->transport_complete_callback(), and depend upon this
value instead of ->se_cmd_flags to determine when to return
or fall through into ->queue_status() code for CAW.
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: <stable@vger.kernel.org> # v3.12+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch addresses a case where iscsi_target_do_tx_login_io()
fails sending the last login response PDU, after the RX/TX
threads have already been started.
The case centers around iscsi_target_rx_thread() not invoking
allow_signal(SIGINT) before the send_sig(SIGINT, ...) occurs
from the failure path, resulting in RX thread hanging
indefinately on iscsi_conn->rx_login_comp.
Note this bug is a regression introduced by:
commit e54198657b65625085834847ab6271087323ffea
Author: Nicholas Bellinger <nab@linux-iscsi.org>
Date: Wed Jul 22 23:14:19 2015 -0700
iscsi-target: Fix iscsit_start_kthreads failure OOPs
To address this bug, complete ->rx_login_complete for good
measure in the failure path, and immediately return from
RX thread context if connection state did not actually reach
full feature phase (TARG_CONN_STATE_LOGGED_IN).
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Smatch complains about returning hard coded error codes, silence this
warning.
drivers/target/iscsi/iscsi_target_parameters.c:211
iscsi_create_default_params() warn: returning -1 instead of -ENOMEM is sloppy
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
TCMU sets TRANSPORT_FLAG_PASSTHROUGH, so INQUIRY commands will not be
emulated by LIO but passed up to userspace. Therefore TCMU should not
set these, just like pscsi doesn't.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
