| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- Revert armada8k GPIO reset change that broke Macchiatobin booting
(Baruch Siach)
- Use actual size config reads on ARM cns3xxx (Koen Vandeputte)
- Fix ARM cns3xxx config write alignment issue (Koen Vandeputte)
- Fix imx6 PHY device link error checking (Leonard Crestez)
- Fix imx6 probe failure on chips without separate PCI power domain
(Leonard Crestez)
* tag 'pci-v5.0-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
Revert "PCI: armada8k: Add support for gpio controlled reset signal"
ARM: cns3xxx: Use actual size reads for PCIe
ARM: cns3xxx: Fix writing to wrong PCI config registers after alignment
PCI: imx: Fix checking pd_pcie_phy device link addition
PCI: imx: Fix probe failure without power domain
|
|
Revert commit 3d71746c42 ("PCI: armada8k: Add support for gpio controlled
reset signal").
That commit breaks boot on Macchiatobin board when a Mellanox NIC is
present in the PCIe slot.
It turns out that full reset cycle requires first comphy serdes
initialization. Reset signal toggle without comphy initialization makes
access to PCI configuration registers stall indefinitely. U-Boot toggles
the Macchiatobin PCIe reset line already at boot, after initializing the
comphy serdes.
So while commit 3d71746c42 ("PCI: armada8k: Add support for gpio controlled
reset signal") enables PCIe on platforms that U-Boot does not touch the
reset line (like Clearfog GT-8K), it breaks PCIe (and boot) on the
Macchiatobin board.
Revert commit 3d71746c42 ("PCI: armada8k: Add support for gpio controlled
reset signal") entirely to fix the Macchiatobin regression.
Reported-by: Sven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
commit 802b7c06adc7 ("ARM: cns3xxx: Convert PCI to use generic config
accessors") reimplemented cns3xxx_pci_read_config() using
pci_generic_config_read32(), which preserved the property of only doing
32-bit reads.
It also replaced cns3xxx_pci_write_config() with pci_generic_config_write(),
so it changed writes from always being 32 bits to being the actual size,
which works just fine.
Given that:
- The documentation does not mention that only 32 bit access is allowed.
- Writes are already executed using the actual size
- Extensive testing shows that 8b, 16b and 32b reads work as intended
Allow read access of any size by replacing pci_generic_config_read32()
with the pci_generic_config_read() accessors.
Fixes: 802b7c06adc7 ("ARM: cns3xxx: Convert PCI to use generic config accessors")
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Krzysztof Halasa <khalasa@piap.pl>
Acked-by: Arnd Bergmann <arnd@arndb.de>
CC: Krzysztof Halasa <khalasa@piap.pl>
CC: Olof Johansson <olof@lixom.net>
CC: Robin Leblon <robin.leblon@ncentric.com>
CC: Rob Herring <robh@kernel.org>
CC: Russell King <linux@armlinux.org.uk>
CC: Tim Harvey <tharvey@gateworks.com>
|
|
Originally, cns3xxx used its own functions for mapping, reading and
writing config registers.
Commit 802b7c06adc7 ("ARM: cns3xxx: Convert PCI to use generic config
accessors") removed the internal PCI config write function in favor of
the generic one:
cns3xxx_pci_write_config() --> pci_generic_config_write()
cns3xxx_pci_write_config() expected aligned addresses, being produced by
cns3xxx_pci_map_bus() while the generic one pci_generic_config_write()
actually expects the real address as both the function and hardware are
capable of byte-aligned writes.
This currently leads to pci_generic_config_write() writing to the wrong
registers.
For instance, upon ath9k module loading:
- driver ath9k gets loaded
- The driver wants to write value 0xA8 to register PCI_LATENCY_TIMER,
located at 0x0D
- cns3xxx_pci_map_bus() aligns the address to 0x0C
- pci_generic_config_write() effectively writes 0xA8 into register 0x0C
(CACHE_LINE_SIZE)
Fix the bug by removing the alignment in the cns3xxx mapping function.
Fixes: 802b7c06adc7 ("ARM: cns3xxx: Convert PCI to use generic config accessors")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Krzysztof Halasa <khalasa@piap.pl>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
CC: stable@vger.kernel.org # v4.0+
CC: Bjorn Helgaas <bhelgaas@google.com>
CC: Olof Johansson <olof@lixom.net>
CC: Robin Leblon <robin.leblon@ncentric.com>
CC: Rob Herring <robh@kernel.org>
CC: Russell King <linux@armlinux.org.uk>
|
|
The check on the device_link_add() return value is wrong;
this leads to erroneous code execution, so fix it.
Fixes: 3f7cceeab895 ("PCI: imx: Add multi-pd support")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
On chips without a separate power domain for PCI (such as 6q/6qp) the
imx6_pcie_attach_pd() function incorrectly returns an error.
Fix by returning 0 if dev_pm_domain_attach_by_name() does not find
anything.
Fixes: 3f7cceeab895 ("PCI: imx: Add multi-pd support")
Reported-by: Lukas F.Hartmann <lukas@mntmn.com>
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
This reverts commit 2d29f6b96d8f80322ed2dd895bca590491c38d34.
It turns out that the fix can lead to a ~20 percent performance regression
in initial writes to the page cache according to iozone. Let's revert this
for now to have more time for a proper fix.
Cc: stable@vger.kernel.org # v3.13+
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kselftest fixes from Shuah Khan:
"This consists of run-time fixes to cpu-hotplug, and seccomp tests,
compile fixes to ir, net, and timers Makefiles"
* tag 'linux-kselftest-5.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests: timers: use LDLIBS instead of LDFLAGS
selftests: net: use LDLIBS instead of LDFLAGS
selftests/seccomp: Enhance per-arch ptrace syscall skip tests
selftests: Use lirc.h from kernel tree, not from system
selftests: cpu-hotplug: fix case where CPUs offline > CPUs present
|
|
Pull NFS client fixes from Anna Schumaker:
"This addresses two bugs, one in the error code handling of
nfs_page_async_flush() and one to fix a potential NULL pointer
dereference in nfs_parse_devname().
Stable bugfix:
- Fix up return value on fatal errors in nfs_page_async_flush()
Other bugfix:
- Fix NULL pointer dereference of dev_name"
* tag 'nfs-for-5.0-3' of git://git.linux-nfs.org/projects/anna/linux-nfs:
NFS: Fix up return value on fatal errors in nfs_page_async_flush()
nfs: Fix NULL pointer dereference of dev_name
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Only three fixes.
The fix for Realtek HD-audio looks lengthy, but it's just a code
shuffling, and the actual changes are fairly small.
The rest are a PCM core fix for a long-standing bug that was recently
scratched by syzkaller, and a trivial USB-audio quirk for DSD support"
* tag 'sound-5.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek - Fixed hp_pin no value
ALSA: pcm: Fix tight loop of OSS capture stream
ALSA: usb-audio: Add Opus #3 to quirks for native DSD support
|
|
There's an issue with how sense requests are handled in IDE. If ide-cd
encounters an error, it queues a sense request. With how IDE request
handling is done, this is the next request we need to handle. But it's
impossible to guarantee this, as another request could come in between
the sense being queued, and ->queue_rq() being run and handling it. If
that request ALSO fails, then we attempt to doubly queue the single
sense request we have.
Since we only support one active request at the time, defer request
processing when a sense request is queued.
Fixes: 600335205b8d "ide: convert to blk-mq"
Reported-by: He Zhe <zhe.he@windriver.com>
Tested-by: He Zhe <zhe.he@windriver.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
To 2.17
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
The request buffers are freed right before copying the pointers.
Use the func args instead which are identical and still valid.
Simple reproducer (requires KASAN enabled) on a cifs mount:
echo foo > foo ; tail -f foo & rm foo
Cc: <stable@vger.kernel.org> # 4.20
Fixes: 179e44d49c2f ("smb3: add tracepoint for sending lease break responses to server")
Signed-off-by: Aurelien Aptel <aaptel@suse.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Paulo Alcantara <palcantara@suse.de>
|
|
The default time is declared in units of microsecnds,
but is used as nanoseconds, resulting in significant
accounting errors for idle state 0 time when all idle
states deeper than 0 are disabled.
Under these unusual conditions, we don't really care
about the poll time limit anyhow.
Fixes: 800fb34a99ce ("cpuidle: poll_state: Disregard disable idle states")
Signed-off-by: Doug Smythies <dsmythies@telus.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
A deadlock has been seen when swicthing clocksources which use
PM-runtime. The call path is:
change_clocksource
...
write_seqcount_begin
...
timekeeping_update
...
sh_cmt_clocksource_enable
...
rpm_resume
pm_runtime_mark_last_busy
ktime_get
do
read_seqcount_begin
while read_seqcount_retry
....
write_seqcount_end
Although we should be safe because we haven't yet changed the
clocksource at that time, we can't do that because of seqcount
protection.
Use ktime_get_mono_fast_ns() instead which is lock safe for such
cases.
With ktime_get_mono_fast_ns, the timestamp is not guaranteed to be
monotonic across an update and as a result can goes backward.
According to update_fast_timekeeper() description: "In the worst
case, this can result is a slightly wrong timestamp (a few
nanoseconds)". For PM-runtime autosuspend, this means only that
the suspend decision may be slightly suboptimal.
Fixes: 8234f6734c5d ("PM-runtime: Switch autosuspend over to using hrtimers")
Reported-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The current dentry number tracking code doesn't distinguish between
positive & negative dentries. It just reports the total number of
dentries in the LRU lists.
As excessive number of negative dentries can have an impact on system
performance, it will be wise to track the number of positive and
negative dentries separately.
This patch adds tracking for the total number of negative dentries in
the system LRU lists and reports it in the 5th field in the
/proc/sys/fs/dentry-state file. The number, however, does not include
negative dentries that are in flight but not in the LRU yet as well as
those in the shrinker lists which are on the way out anyway.
The number of positive dentries in the LRU lists can be roughly found by
subtracting the number of negative dentries from the unused count.
Matthew Wilcox had confirmed that since the introduction of the
dentry_stat structure in 2.1.60, the dummy array was there, probably for
future extension. They were not replacements of pre-existing fields.
So no sane applications that read the value of /proc/sys/fs/dentry-state
will do dummy thing if the last 2 fields of the sysctl parameter are not
zero. IOW, it will be safe to use one of the dummy array entry for
negative dentry count.
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The list_lru structure is essentially just a pointer to a table of
per-node LRU lists. Even if CONFIG_MEMCG_KMEM is defined, the list
field is just used for LRU list registration and shrinker_id is set at
initialization. Those fields won't need to be touched that often.
So there is no point to make the list_lru structures to sit in their own
cachelines.
Signed-off-by: Waiman Long <longman@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The nr_dentry_unused per-cpu counter tracks dentries in both the LRU
lists and the shrink lists where the DCACHE_LRU_LIST bit is set.
The shrink_dcache_sb() function moves dentries from the LRU list to a
shrink list and subtracts the dentry count from nr_dentry_unused. This
is incorrect as the nr_dentry_unused count will also be decremented in
shrink_dentry_list() via d_shrink_del().
To fix this double decrement, the decrement in the shrink_dcache_sb()
function is taken out.
Fixes: 4e717f5c1083 ("list_lru: remove special case function list_lru_dispose_all."
Cc: stable@kernel.org
Signed-off-by: Waiman Long <longman@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
"A few more fixes this time:
- Two patches to fix the error path of the map_sg implementation of
the AMD IOMMU driver.
- Also a missing IOTLB flush is fixed in the AMD IOMMU driver.
- Memory leak fix for the Intel IOMMU driver.
- Fix a regression in the Mediatek IOMMU driver which caused device
initialization to fail (seen as broken HDMI output)"
* tag 'iommu-fixes-v5.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Fix IOMMU page flush when detach device from a domain
iommu/mediatek: Use correct fwspec in mtk_iommu_add_device()
iommu/vt-d: Fix memory leak in intel_iommu_put_resv_regions()
iommu/amd: Unmap all mapped pages in error path of map_sg
iommu/amd: Call free_iova_fast with pfn in map_sg
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Here is a bunch of GPIO fixes for the v5.0 series. I was helped out by
Bartosz in collecting these fixes, for which I am very grateful, the
biggest achievement in GPIO right now is work distribution.
There is one serious core fix (timestamping) and a bunch of driver
fixes:
- Fix timestamps on nested IRQs
- Handle IRQs properly in multiple instances of PCF857x
- Use the right data register and IRQ type setting in the Spreadtrum
GPIO driver
- Let the value argument work properly when setting direction in the
Altera GPIO driver
- Mask interrupts properly in the vf610 driver"
* tag 'gpio-v5.0-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: vf610: Mask all GPIO interrupts
gpio: altera-a10sr: Set proper output level for direction_output
gpio: sprd: Fix incorrect irq type setting for the async EIC
gpio: sprd: Fix the incorrect data register
gpiolib: fix line event timestamps for nested irqs
gpio: pcf857x: Fix interrupts on multiple instances
|
|
Florian reported a io hung issue when fsync(). It should be
triggered by following race condition.
data + post flush a flush
blk_flush_complete_seq
case REQ_FSEQ_DATA
blk_flush_queue_rq
issued to driver blk_mq_dispatch_rq_list
try to issue a flush req
failed due to NON-NCQ command
.queue_rq return BLK_STS_DEV_RESOURCE
request completion
req->end_io // doesn't check RESTART
mq_flush_data_end_io
case REQ_FSEQ_POSTFLUSH
blk_kick_flush
do nothing because previous flush
has not been completed
blk_mq_run_hw_queue
insert rq to hctx->dispatch
due to RESTART is still set, do nothing
To fix this, replace the blk_mq_run_hw_queue in mq_flush_data_end_io
with blk_mq_sched_restart to check and clear the RESTART flag.
Fixes: bd166ef1 (blk-mq-sched: add framework for MQ capable IO schedulers)
Reported-by: Florian Stecker <m19@florianstecker.de>
Tested-by: Florian Stecker <m19@florianstecker.de>
Signed-off-by: Jianchao Wang <jianchao.w.wang@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
syzbot is hitting flush_work() warning caused by commit 4d43d395fed12463
("workqueue: Try to catch flush_work() without INIT_WORK().") [1].
Although that commit did not expect INIT_WORK(NULL) case, calling
flush_work() without setting a valid callback should be avoided anyway.
Fix this problem by setting a no-op callback instead of NULL.
[1] https://syzkaller.appspot.com/bug?id=e390366bc48bc82a7c668326e0663be3b91cbd29
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reported-and-tested-by: syzbot <syzbot+ba2a929dcf8e704c180e@syzkaller.appspotmail.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Pull networking fixes from David Miller:
1) Need to save away the IV across tls async operations, from Dave
Watson.
2) Upon successful packet processing, we should liberate the SKB with
dev_consume_skb{_irq}(). From Yang Wei.
3) Only apply RX hang workaround on effected macb chips, from Harini
Katakam.
4) Dummy netdev need a proper namespace assigned to them, from Josh
Elsasser.
5) Some paths of nft_compat run lockless now, and thus we need to use a
proper refcnt_t. From Florian Westphal.
6) Avoid deadlock in mlx5 by doing IRQ locking, from Moni Shoua.
7) netrom does not refcount sockets properly wrt. timers, fix that by
using the sock timer API. From Cong Wang.
8) Fix locking of inexact inserts of xfrm policies, from Florian
Westphal.
9) Missing xfrm hash generation bump, also from Florian.
10) Missing of_node_put() in hns driver, from Yonglong Liu.
11) Fix DN_IFREQ_SIZE, from Johannes Berg.
12) ip6mr notifier is invoked during traversal of wrong table, from Nir
Dotan.
13) TX promisc settings not performed correctly in qed, from Manish
Chopra.
14) Fix OOB access in vhost, from Jason Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (52 commits)
MAINTAINERS: Add entry for XDP (eXpress Data Path)
net: set default network namespace in init_dummy_netdev()
net: b44: replace dev_kfree_skb_xxx by dev_consume_skb_xxx for drop profiles
net: caif: call dev_consume_skb_any when skb xmit done
net: 8139cp: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
net: macb: Apply RXUBR workaround only to versions with errata
net: ti: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
net: apple: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
net: amd8111e: replace dev_kfree_skb_irq by dev_consume_skb_irq
net: alteon: replace dev_kfree_skb_irq by dev_consume_skb_irq
net: tls: Fix deadlock in free_resources tx
net: tls: Save iv in tls_rec for async crypto requests
vhost: fix OOB in get_rx_bufs()
qed: Fix stack out of bounds bug
qed: Fix system crash in ll2 xmit
qed: Fix VF probe failure while FLR
qed: Fix LACP pdu drops for VFs
qed: Fix bug in tx promiscuous mode settings
net: i825xx: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
netfilter: ipt_CLUSTERIP: fix warning unused variable cn
...
|
|
When doing reads beyound the end of a file the server returns
error STATUS_END_OF_FILE error which is mapped to -ENODATA.
Currently we report it as a failure which confuses read stats.
Change it to not consider -ENODATA as failure for stat purposes.
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
CC: Stable <stable@vger.kernel.org>
|
|
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
CC: Stable <stable@vger.kernel.org>
|
|
Currently we log success once we send an async IO request to
the server. Instead we need to analyse a response and then log
success or failure for a particular command. Also fix argument
list for read logging.
Cc: <stable@vger.kernel.org> # 4.18
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
Allocation of a page array for non-cached IO was separated from
allocation of rdata and wdata structures and this introduced memory
leaks and a possible null pointer dereference. This patch fixes
these problems.
Cc: <stable@vger.kernel.org>
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
minus the various headers and blobs that will be part of the reply.
or else we might trigger a session reconnect.
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
|
|
The size of the fixed part of the create response is 88 bytes not 56.
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
|
|
Ensure that we return the fatal error value that caused us to exit
nfs_page_async_flush().
Fixes: c373fff7bd25 ("NFSv4: Don't special case "launder"")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Cc: stable@vger.kernel.org # v4.12+
Reviewed-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
|
|
The vma->vm_mm can become impossible to get before rdma_umap_close() is
called, in this case we must not try to get an mm that is already
undergoing process exit. In this case there is no need to wait for
anything as the VMA will be destroyed by another thread soon and is
already effectively 'unreachable' by userspace.
BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
PGD 800000012bc50067 P4D 800000012bc50067 PUD 129db5067 PMD 0
Oops: 0000 [#1] SMP PTI
CPU: 1 PID: 2050 Comm: bash Tainted: G W OE 4.20.0-rc6+ #3
Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
RIP: 0010:__rb_erase_color+0xb9/0x280
Code: 84 17 01 00 00 48 3b 68 10 0f 84 15 01 00 00 48 89
58 08 48 89 de 48 89 ef 4c 89 e3 e8 90 84 22 00 e9 60 ff ff ff 48 8b 5d
10 <f6> 03 01 0f 84 9c 00 00 00 48 8b 43 10 48 85 c0 74 09 f6 00 01 0f
RSP: 0018:ffffbecfc090bab8 EFLAGS: 00010246
RAX: ffff97616346cf30 RBX: 0000000000000000 RCX: 0000000000000101
RDX: 0000000000000000 RSI: ffff97623b6ca828 RDI: ffff97621ef10828
RBP: ffff97621ef10828 R08: ffff97621ef10828 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: ffff97623b6ca838
R13: ffffffffbb3fef50 R14: ffff97623b6ca828 R15: 0000000000000000
FS: 00007f7a5c31d740(0000) GS:ffff97623bb00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000000 CR3: 000000011255a000 CR4: 00000000000006e0
Call Trace:
unlink_file_vma+0x3b/0x50
free_pgtables+0xa1/0x110
exit_mmap+0xca/0x1a0
? mlx5_ib_dealloc_pd+0x28/0x30 [mlx5_ib]
mmput+0x54/0x140
uverbs_user_mmap_disassociate+0xcc/0x160 [ib_uverbs]
uverbs_destroy_ufile_hw+0xf7/0x120 [ib_uverbs]
ib_uverbs_remove_one+0xea/0x240 [ib_uverbs]
ib_unregister_device+0xfb/0x200 [ib_core]
mlx5_ib_remove+0x51/0xe0 [mlx5_ib]
mlx5_remove_device+0xc1/0xd0 [mlx5_core]
mlx5_unregister_device+0x3d/0xb0 [mlx5_core]
remove_one+0x2a/0x90 [mlx5_core]
pci_device_remove+0x3b/0xc0
device_release_driver_internal+0x16d/0x240
unbind_store+0xb2/0x100
kernfs_fop_write+0x102/0x180
__vfs_write+0x36/0x1a0
? __alloc_fd+0xa9/0x170
? set_close_on_exec+0x49/0x70
vfs_write+0xad/0x1a0
ksys_write+0x52/0xc0
do_syscall_64+0x5b/0x180
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Cc: <stable@vger.kernel.org> # 4.19
Fixes: 5f9794dc94f5 ("RDMA/ucontext: Add a core API for mmaping driver IO memory")
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Add multiple people as maintainers for XDP, sorted alphabetically.
XDP is also tied to driver level support and code, but we cannot add all
drivers to the list. Instead K: and N: match on 'xdp' in hope to catch some
of those changes in drivers.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Assign a default net namespace to netdevs created by init_dummy_netdev().
Fixes a NULL pointer dereference caused by busy-polling a socket bound to
an iwlwifi wireless device, which bumps the per-net BUSYPOLLRXPACKETS stat
if napi_poll() received packets:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000190
IP: napi_busy_loop+0xd6/0x200
Call Trace:
sock_poll+0x5e/0x80
do_sys_poll+0x324/0x5a0
SyS_poll+0x6c/0xf0
do_syscall_64+0x6b/0x1f0
entry_SYSCALL_64_after_hwframe+0x3d/0xa2
Fixes: 7db6b048da3b ("net: Commonize busy polling code to focus on napi_id instead of socket")
Signed-off-by: Josh Elsasser <jelsasser@appneta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The skb should be freed by dev_consume_skb_any() in b44_start_xmit()
when bounce_skb is used. The skb is be replaced by bounce_skb, so the
original skb should be consumed(not drop).
dev_consume_skb_irq() should be called in b44_tx() when skb xmit
done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The skb shouled be consumed when xmit done, it makes drop profiles
(dropwatch, perf) more friendly.
dev_kfree_skb_irq()/kfree_skb() shouled be replaced by
dev_consume_skb_any(), it makes code cleaner.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dev_consume_skb_irq() should be called in cp_tx() when skb xmit
done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The interrupt handler contains a workaround for RX hang applicable
to Zynq and AT91RM9200 only. Subsequent versions do not need this
workaround. This workaround unnecessarily resets RX whenever RX used
bit read is observed, which can be often under heavy traffic. There
is no other action performed on RX UBR interrupt. Hence introduce a
CAPS mask; enable this interrupt and workaround only on affected
versions.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix hp_pin always no value.
[More notes on the changes:
The hp_pin value that is referred in alc294_hp_init() is always zero
at the moment the function gets called, hence this is actually
useless as in the current code.
And, this kind of init sequence should be called from the codec init
callback, instead of the parser function. So, the first fix in this
patch to move the call call into its own init_hook.
OTOH, this function is needed to be called only once after the boot,
and it'd take too long for invoking at each resume (where the init
callback gets called). So we add a new flag and invoke this only
once as an additional fix.
The one case is still not covered, though: S4 resume. But this
change itself won't lead to any regression in that regard, so we
leave S4 issue as is for now and fix it later. -- tiwai ]
Fixes: bde1a7459623 ("ALSA: hda/realtek - Fixed headphone issue for ALC700")
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Pull MD fix from Song.
* 'md-fixes' of https://github.com/liu-song-6/linux:
md/raid5: fix 'out of memory' during raid cache recovery
|
|
Add BACKLIGHT_LCD_SUPPORT for SAMSUNG_Q10 to fix the
warning: unmet direct dependencies detected for BACKLIGHT_CLASS_DEVICE.
SAMSUNG_Q10 selects BACKLIGHT_CLASS_DEVICE but BACKLIGHT_CLASS_DEVICE
depends on BACKLIGHT_LCD_SUPPORT.
Copy BACKLIGHT_LCD_SUPPORT dependency into SAMSUNG_Q10 to fix:
WARNING: unmet direct dependencies detected for BACKLIGHT_CLASS_DEVICE
Depends on [n]: HAS_IOMEM [=y] && BACKLIGHT_LCD_SUPPORT [=n]
Selected by [y]:
- SAMSUNG_Q10 [=y] && X86 [=y] && X86_PLATFORM_DEVICES [=y] && ACPI [=y]
Signed-off-by: Sinan Kaya <okaya@kernel.org>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Add BACKLIGHT_LCD_SUPPORT for ACPI_CMPC to fix the
warning: unmet direct dependencies detected for BACKLIGHT_CLASS_DEVICE.
ACPI_CMPC selects BACKLIGHT_CLASS_DEVICE but BACKLIGHT_CLASS_DEVICE
depends on BACKLIGHT_LCD_SUPPORT.
Copy BACKLIGHT_LCD_SUPPORT dependency into ACPI_CMPC to fix
WARNING: unmet direct dependencies detected for BACKLIGHT_CLASS_DEVICE
Depends on [n]: HAS_IOMEM [=y] && BACKLIGHT_LCD_SUPPORT [=n]
Selected by [y]:
- ACPI_CMPC [=y] && X86 [=y] && X86_PLATFORM_DEVICES [=y] && ACPI [=y] && INPUT [=y] && (RFKILL [=n] || RFKILL [=n]=n)
Signed-off-by: Sinan Kaya <okaya@kernel.org>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
After commit 5d32a66541c4 ("PCI/ACPI: Allow ACPI to be built without
CONFIG_PCI set") dependencies on CONFIG_PCI that previously were
satisfied implicitly through dependencies on CONFIG_ACPI have to be
specified directly.
WARNING: unmet direct dependencies detected for I2C_DESIGNWARE_PLATFORM
Depends on [n]: I2C [=y] && HAS_IOMEM [=y] && (ACPI [=y] && COMMON_CLK [=n] || !ACPI [=y])
Selected by [y]:
- MFD_TPS68470 [=y] && HAS_IOMEM [=y] && ACPI [=y] && I2C [=y]=y
MFD_TPS68470 is an ACPI only device and selects I2C_DESIGNWARE_PLATFORM.
I2C_DESIGNWARE_PLATFORM does not have any configuration today for ACPI
support without CONFIG_PCI set.
For sake of a quick fix this introduces a new mandatory dependency to
the driver which may survive without it. Otherwise we need to revisit
the driver architecture to address this properly.
Fixes: 5d32a66541c46 ("PCI/ACPI: Allow ACPI to be built without CONFIG_PCI set")
Signed-off-by: Sinan Kaya <okaya@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
dev_consume_skb_irq() should be called in cpmac_end_xmit() when
xmit done. It makes drop profiles more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dev_consume_skb_irq() should be called in bmac_txdma_intr() when
xmit done. It makes drop profiles more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dev_consume_skb_irq() should be called in amd8111e_tx() when xmit
done. It makes drop profiles more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dev_consume_skb_irq() should be called in ace_tx_int() when xmit
done. It makes drop profiles more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If there are outstanding async tx requests (when crypto returns EINPROGRESS),
there is a potential deadlock: the tx work acquires the lock, while we
cancel_delayed_work_sync() while holding the lock. Drop the lock while waiting
for the work to complete.
Fixes: a42055e8d2c30 ("Add support for async encryption of records...")
Signed-off-by: Dave Watson <davejwatson@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
aead_request_set_crypt takes an iv pointer, and we change the iv
soon after setting it. Some async crypto algorithms don't save the iv,
so we need to save it in the tls_rec for async requests.
Found by hardcoding x64 aesni to use async crypto manager (to test the async
codepath), however I don't think this combination can happen in the wild.
Presumably other hardware offloads will need this fix, but there have been
no user reports.
Fixes: a42055e8d2c30 ("Add support for async encryption of records...")
Signed-off-by: Dave Watson <davejwatson@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After batched used ring updating was introduced in commit e2b3b35eb989
("vhost_net: batch used ring update in rx"). We tend to batch heads in
vq->heads for more than one packet. But the quota passed to
get_rx_bufs() was not correctly limited, which can result a OOB write
in vq->heads.
headcount = get_rx_bufs(vq, vq->heads + nvq->done_idx,
vhost_len, &in, vq_log, &log,
likely(mergeable) ? UIO_MAXIOV : 1);
UIO_MAXIOV was still used which is wrong since we could have batched
used in vq->heads, this will cause OOB if the next buffer needs more
than 960 (1024 (UIO_MAXIOV) - 64 (VHOST_NET_BATCH)) heads after we've
batched 64 (VHOST_NET_BATCH) heads:
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
=============================================================================
BUG kmalloc-8k (Tainted: G B ): Redzone overwritten
-----------------------------------------------------------------------------
INFO: 0x00000000fd93b7a2-0x00000000f0713384. First byte 0xa9 instead of 0xcc
INFO: Allocated in alloc_pd+0x22/0x60 age=3933677 cpu=2 pid=2674
kmem_cache_alloc_trace+0xbb/0x140
alloc_pd+0x22/0x60
gen8_ppgtt_create+0x11d/0x5f0
i915_ppgtt_create+0x16/0x80
i915_gem_create_context+0x248/0x390
i915_gem_context_create_ioctl+0x4b/0xe0
drm_ioctl_kernel+0xa5/0xf0
drm_ioctl+0x2ed/0x3a0
do_vfs_ioctl+0x9f/0x620
ksys_ioctl+0x6b/0x80
__x64_sys_ioctl+0x11/0x20
do_syscall_64+0x43/0xf0
entry_SYSCALL_64_after_hwframe+0x44/0xa9
INFO: Slab 0x00000000d13e87af objects=3 used=3 fp=0x (null) flags=0x200000000010201
INFO: Object 0x0000000003278802 @offset=17064 fp=0x00000000e2e6652b
Fixing this by allocating UIO_MAXIOV + VHOST_NET_BATCH iovs for
vhost-net. This is done through set the limitation through
vhost_dev_init(), then set_owner can allocate the number of iov in a
per device manner.
This fixes CVE-2018-16880.
Fixes: e2b3b35eb989 ("vhost_net: batch used ring update in rx")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The "hostdata->dev" pointer is NULL here. We set "hostdata->dev = dev;"
later in the function and we also use "hostdata->dev" when we call
dma_free_attrs() in NCR_700_release().
This bug predates git version control.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
