| Age | Commit message (Collapse) | Author |
|---|
|
Since we have a little function to see whether a channel
program address falls within a range of CCWs, let's use
it in the other places of code that make these checks.
(Why isn't ccw_head fully removed? Well, because this
way some longs lines don't have to be reflowed.)
Signed-off-by: Eric Farman <farman@linux.ibm.com>
Message-Id: <20190222183941.29596-3-farman@linux.ibm.com>
Reviewed-by: Farhan Ali <alifm@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
|
|
The routine ccwchain_calc_length() is tasked with looking at a
channel program, seeing how many CCWs are chained together by
the presence of the Chain-Command flag, and returning a count
to the caller.
Previously, it also considered a Transfer-in-Channel CCW as being
an appropriate mechanism for chaining. The problem at the time
was that the TIC CCW will almost certainly not go to the next CCW
in memory (because the CC flag would be sufficient), and so
advancing to the next 8 bytes will cause us to read potentially
invalid memory. So that comparison was removed, and the target
of the TIC is processed as a new chain.
This is fine when a TIC goes to a new chain (consider a NOP+TIC to
a channel program that is being redriven), but there is another
scenario where this falls apart. A TIC can be used to "rewind"
a channel program, for example to find a particular record on a
disk with various orientation CCWs. In this case, we DO want to
consider the memory after the TIC since the TIC will be skipped
once the requested criteria is met. This is due to the Status
Modifier presented by the device, though software doesn't need to
operate on it beyond understanding the behavior change of how the
channel program is executed.
So to handle this, we will re-introduce the check for a TIC CCW
but limit it by examining the target of the TIC. If the TIC
doesn't go back into the current chain, then current behavior
applies; we should stop counting CCWs and let the target of the
TIC be handled as a new chain. But, if the TIC DOES go back into
the current chain, then we need to keep looking at the memory after
the TIC for when the channel breaks out of the TIC loop. We can't
use tic_target_chain_exists() because the chain in question hasn't
been built yet, so we will redefine that comparison with some small
functions to make it more readable and to permit refactoring later.
Fixes: 405d566f98ae ("vfio-ccw: Don't assume there are more ccws after a TIC")
Signed-off-by: Eric Farman <farman@linux.ibm.com>
Message-Id: <20190222183941.29596-2-farman@linux.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Farhan Ali <alifm@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
|
|
Comment in tdc_config.py recommends putting customizations in
tdc_config_local.py file that wasn't included in gitignore. Add the local
config file to gitignore.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Function walker_check_empty() incorrectly verifies that tp pointer is not
NULL, instead of actual filter pointer. Fix conditional to check the right
pointer. Adjust filter pointer naming accordingly to other cls API
functions.
Fixes: 6676d5e416ee ("net: sched: set dedicated tcf_walker flag when tp is empty")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reported-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the incorrect reference link to RFC 8033
Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/mellanox/mlxsw/spectrum.c: In function 'mlxsw_sp_port_get_link_ksettings':
drivers/net/ethernet/mellanox/mlxsw/spectrum.c:3062:5: warning:
variable 'autoneg_status' set but not used [-Wunused-but-set-variable]
It's not used since commit 475b33cb66c9 ("mlxsw: spectrum: Remove unsupported
eth_proto_lp_advertise field in PTYS")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Roopa Prabhu says:
====================
vxlan: create and changelink extack support
This series adds extack support to changelink paths.
In the process re-factors flag sets to a separate helper.
Also adds some changelink testcases to rtnetlink.sh
(This series was initially part of another series that
tried to support changelink for more attributes.
But after some feedback from sabrina, i have dropped the
'support changelink for more attributes' part because some
of them cannot be supported today or may require additional
use-case handling code. These can be done separately
as and when we see the need for it.)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch extends rtnetlink.sh to cover some vxlan flag
netlink attribute sets.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds extack coverage in vxlan link
create and changelink paths. Introduces a new helper
vxlan_nl2flags to consolidate flag attribute validation.
thanks to Johannes Berg for some tips to construct the
generic vxlan flag extack strings.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jakub Kicinski says:
====================
devlink: make ethtool compat reliable
This is a follow up to the series which added device flash
updates via devlink. I went with the approach of adding a
new NDO in the end. It seems to end up looking cleaner.
First patch removes the option to build devlink as a module.
Users can still decide to not build it, but the module option
ends up not being worth the maintenance cost.
Next two patches add a NDO which can be used to ask the driver
to return a devlink instance associated with a given netdev,
instead of iterating over devlink ports. Drivers which implement
this NDO must take into account the potential impact on the
visibility of the devlink instance.
With the new NDO in place we can remove NFP ethtool flash update
code.
Fifth patch makes sure we hold a reference to dev while
callbacks are active.
Last but not least the NULL-check of devlink->ops is moved
to instance allocation time.
Last but not least missing checks for devlink->ops are added.
There is currently no driver registering devlink without ops,
so can just fix this in -next.
v2 (Michal): add netdev_to_devlink() in patch 3.
v3 (Florian):
- add missing checks for devlink->ops;
- move locking/holding into devlink_compat_ functions.
v4 (Jiri):
- hold devlink_mutex around callbacks (patch 2);
- require non-NULL ops (patch 6).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 76726ccb7f46 ("devlink: add flash update command") and
commit 2d8dc5bbf4e7 ("devlink: Add support for reload")
access devlink ops without NULL-checking. There is, however, no
driver which would pass in NULL ops, so let's just make that
a requirement. Remove the now unnecessary NULL-checking.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When ethtool is calling into devlink compat code make sure we have
a reference on the netdevice on which the operation was invoked.
v3: move the hold/lock logic into devlink_compat_* functions (Florian)
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that devlink fallback will be called reliably, we can remove
the ethtool flashing code.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Support getting devlink instance from a new NDO.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of iterating over all devlink ports add a NDO which
will return the devlink instance from the driver.
v2: add the netdev_to_devlink() helper (Michal)
v3: check that devlink has ops (Florian)
v4: hold devlink_mutex (Jiri)
Suggested-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Being able to build devlink as a module causes growing pains.
First all drivers had to add a meta dependency to make sure
they are not built in when devlink is built as a module. Now
we are struggling to invoke ethtool compat code reliably.
Make devlink code built-in, users can still not build it at
all but the dynamically loadable module option is removed.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The *i2c and *i2c_8606 are no longer used since this driver was converted
to use regmap helpers. The *chip and *regulator are not really required.
So remove these unused fields.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Set volt_table filed then we can use regulator_list_voltage_table.
Since we have volt_table setting, now we can remove vol_table from
struct pm8607_regulator_info.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
They should never change, make them const.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This driver uses regulator_get/set_voltage_sel_regmap so it does not use
vsel_shift. Actually, vsel_shift can be calculated by vsel_mask setting.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Now that all users of struct inet_frag_queue have been converted
to use 'rb_fragments', remove the unused 'fragments' field.
Build with `make allyesconfig` succeeded. ip_defrag selftest passed.
Signed-off-by: Peter Oskolkov <posk@google.com>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
Dummy write in capture master mode is used to gate
bus clocks. This write is useless in slave mode
as the clocks are not managed by slave.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When snd_pcm_stop_xrun() is called in interrupt routine,
substream context may have already been released.
Add protection on substream context.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Clocks do not need to be released on driver removal,
as this is already managed before.
Remove useless remove callback.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
DMA configuration is not balanced on start/stop.
Move DMA configuration to trigger callback.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Move counter handling to trigger start section
to manage multiple start/stop events.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
I2S supports 16 bits data in 32 channel length.
However the expected driver behavior, is to
set channel length to 16 bits when data format is 16 bits.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Because of regmap cache, interrupts may not be cleared
as expected.
Declare IFCR register as write only and make writings
to IFCR register unconditional.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/ath/ath9k/recv.c: In function 'ath_rx_count_airtime':
drivers/net/wireless/ath/ath9k/recv.c:1010:18: warning:
variable 'acq' set but not used [-Wunused-but-set-variable]
It's not used after 89cea7493a34 ("ath9k: Switch to mac80211 TXQ scheduling
and airtime APIs"). Also remove related variables.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
SPUR DOWN field returns spurup instead of spurdown.
Signed-off-by: Andrea Greco <a.greco@4sigma.it>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Since ath9k reports airtime usage directly using the
ieee80211_report_airtime() callback, it shouldn't also report it using the
tx_time in status. Make sure the field is zeroed before TX status is
reported to avoid spurious airtime being accounted by bits being left over
from earlier uses of the cb.
Fixes: 89cea7493a34 ("ath9k: Switch to mac80211 TXQ scheduling and airtime APIs")
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
WCN3990 firmware versions WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1 & onwards
supports maximum 33 peers including self peer. To support maximum peers,
send updated peer param to firmware during initialization.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Signed-off-by: Abhishek Ambure <aambure@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The calibration data fetch will trigger sdio error, then sdio will
become fail untill reboot system.
If happens when run ifconfig wlan down, then ifconfig wlan up will
fail untill reboot system.Remove it fix the ifconfig wlan issue.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00005-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The length of wmi tlv command for management tx send is calculated
incorrectly in case of protected management frames as there is addition
of IEEE80211_CCMP_MIC_LEN twice. This leads to improper behaviour of
firmware as the wmi tlv mgmt tx send command for protected mgmt frames
is formed wrongly.
Fix the length calculation of wmi tlv command for mgmt tx send in case
of protected management frames by adding the IEEE80211_CCMP_MIC_LEN only
once.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: 1807da49733e "ath10k: wmi: add management tx by reference support over wmi"
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The SDIO firmware does not provide RSSI value to the host, it's only set to
zero. In that case don't report the value to mac80211. One risk here is that
value zero might be a valid value with other firmware, currently there's no way
to detect that.
Without the fix, the rssi value indicated by iw changes between the actual
value and -95.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00005-QCARMSWP-1.
Co-developed-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The target device needs to be reset during power_down(), otherwise only the
first power_up() will work. And as ath10k calls power_up() during driver
initialisation the driver would be otherwise unusable.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00005-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The SDIO firmware may turn it on based on scratch registers so disable the
firmware log to avoid that.
Co-developed-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The SDIO firmware does not allow transmitting packets with the
reduced tx completion HI_ACS option. SDIO firmware uses 1544 as
alternate credit size, which is not big enough for the maximum sized
mac80211 frames. Disable both these HI_ACS flags for SDIO.
Co-developed-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This is a theoretical fix, the issue is found in code review.
When adding the host memory chunks into wmi-tlv init command,
there is no separate tlv header for each host memory chunk
in the struct array, which breaches the convention between
host and firmware, will result in mismatch between the two.
To fix this issue, add separate tlv headers for the host
memory chunks in wmi-tlv init command.
Signed-off-by: Yu Wang <yyuwang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Currently after enabling the WMI debug logging,
there is no detail printed about the param id
and the param value for the pdev, vdev and
peer params which are set.
Enhance the WMI logging to print the param id
and the param value for pdev, vdev and peer set
param wmi commands.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01387-QCAHLSWMTPLZ-1
WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In WCN3990, WMI_TLV_SERVICE_TX_DATA_MGMT_ACK_RSSI service Indicates that
the firmware has the capability to send the RSSI value of the ACK for all
data and management packets transmitted.
If WMI_RSRC_CFG_FLAG_TX_ACK_RSSI is set in host capability then firmware
sends RSSI value in "data" tx completion event. Host extracts ack rssi
values of data packets from their tx completion event.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1
Signed-off-by: Abhishek Ambure <aambure@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In WCN3990, WMI_TLV_SERVICE_TX_DATA_MGMT_ACK_RSSI service Indicates that
the firmware has the capability to send the RSSI value of the ACK for all
data and management packets transmitted.
If WMI_RSRC_CFG_FLAG_TX_ACK_RSSI is set in host capability then firmware
sends RSSI value in "management" tx completion event. Host extracts ack
rssi values of management packets from their tx completion event.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1
Signed-off-by: Abhishek Ambure <aambure@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
When the driver receives the tx completion of the
descriptor over ce, it clears the nbytes configured
for that particular descriptor. WCN3990 uses ce
descriptors with 64-bit address.
Currently during handling the tx completion of the
descriptors, the nbytes are accessed from the descriptors
using ce_desc for 32-bit targets. This will lead to clearing
of memory at incorrect offset if DMA MASK is set to greater
than 32 bits.
Attach different ce tx copy completed handler for targets
using address above 32-bit address.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01387-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
When building with -Wsometimes-uninitialized, Clang warns:
arch/powerpc/xmon/ppc-dis.c:157:7: warning: variable 'opcode' is used
uninitialized whenever 'if' condition is false
[-Wsometimes-uninitialized]
if (cpu_has_feature(CPU_FTRS_POWER9))
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
arch/powerpc/xmon/ppc-dis.c:167:7: note: uninitialized use occurs here
if (opcode == NULL)
^~~~~~
arch/powerpc/xmon/ppc-dis.c:157:3: note: remove the 'if' if its
condition is always true
if (cpu_has_feature(CPU_FTRS_POWER9))
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
arch/powerpc/xmon/ppc-dis.c:132:38: note: initialize the variable
'opcode' to silence this warning
const struct powerpc_opcode *opcode;
^
= NULL
1 warning generated.
This warning seems to make no sense on the surface because opcode is set
to NULL right below this statement. However, there is a comma instead of
semicolon to end the dialect assignment, meaning that the opcode
assignment only happens in the if statement. Properly terminate that
line so that Clang no longer warns.
Fixes: 5b102782c7f4 ("powerpc/xmon: Enable disassembly files (compilation changes)")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The OPAL call wrapper gets interrupt disabling wrong. It disables
interrupts just by clearing MSR[EE], which has two problems:
- It doesn't call into the IRQ tracing subsystem, which means tracing
across OPAL calls does not always notice IRQs have been disabled.
- It doesn't go through the IRQ soft-mask code, which causes a minor
bug. MSR[EE] can not be restored by saving the MSR then clearing
MSR[EE], because a racing interrupt while soft-masked could clear
MSR[EE] between the two steps. This can cause MSR[EE] to be
incorrectly enabled when the OPAL call returns. Fortunately that
should only result in another masked interrupt being taken to
disable MSR[EE] again, but it's a bit sloppy.
The existing code also saves MSR to PACA, which is not re-entrant if
there is a nested OPAL call from different MSR contexts, which can
happen these days with SRESET interrupts on bare metal.
To fix these issues, move the tracing and IRQ handling code to C, and
call into asm just for the low level call when everything is ready to
go. Save the MSR on stack rather than PACA.
Performance cost is kept to a minimum with a few optimisations:
- The endian switch upon return is combined with the MSR restore,
which avoids an expensive context synchronizing operation for LE
kernels. This makes up for the additional mtmsrd to enable
interrupts with local_irq_enable().
- blr is now used to return from the opal_* functions that are called
as C functions, to avoid link stack corruption. This requires a
skiboot fix as well to keep the call stack balanced.
A NULL call is more costly after this, (410ns->430ns on POWER9), but
OPAL calls are generally not performance critical at this scale.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Handlers for interrupts that set DAR / DSISR, set MSR[RI] before those
SPRs are read. If a d-side machine check hits in this window, DAR /
DSISR will be clobbered silently, leading to random corruption.
Fix this by having handlers save those registers before setting MSR[RI].
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
A subsequent fix for data interrupts (those that set DAR / DSISR)
requires some interrupt macros to be open-coded, and also requires
the 0x300 interrupt handler to be moved out-of-line.
This patch does that without changing behaviour, which makes the later
fix a smaller change.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Code that uses HSRR registers is not required to clear MSR[RI] by
convention, however the system reset NMI itself may use HSRR
registers (e.g., to call OPAL) and clobber them.
Rather than introduce the requirement to clear RI in order to use
HSRRs, have system reset interrupt save and restore HSRRs.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
