| Age | Commit message (Collapse) | Author |
|---|
|
Octeontx2/CN10k MAC block supports DMAC filters. DMAC filters
can be installed on the interface through ethtool.
When a user installs a DMAC filter, the interface's MAC address
is implicitly added to the filter list. To ensure consistency,
this MAC address must be kept in sync with the pfvf->mac_addr field,
which is used to install MAC-based NPC rules.
This patch updates the pfvf->mac_addr field with the programmed MAC
address and also enables VF interfaces to install DMAC filters.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250720163638.1560323-2-hkelam@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This patch enables batched RX buffer replenishment in ibmveth by
using the new firmware-supported h_add_logical_lan_buffers() hcall
to submit up to 8 RX buffers in a single call, instead of repeatedly
calling the single-buffer h_add_logical_lan_buffer() hcall.
During the probe, with the patch, the driver queries ILLAN attributes
to detect IBMVETH_ILLAN_RX_MULTI_BUFF_SUPPORT bit. If the attribute is
present, rx_buffers_per_hcall is set to 8, enabling batched replenishment.
Otherwise, it defaults to 1, preserving the original upstream behavior
with no change in code flow for unsupported systems.
The core rx replenish logic remains the same. But when batching
is enabled, the driver aggregates up to 8 fully prepared descriptors
into a single h_add_logical_lan_buffers() hypercall. If any allocation
or DMA mapping fails while preparing a batch, only the successfully
prepared buffers are submitted, and the remaining are deferred for
the next replenish cycle.
If at runtime the firmware stops accepting the batched hcall—e,g,
after a Live Partition Migration (LPM) to a host that does not
support h_add_logical_lan_buffers(), the hypercall returns H_FUNCTION.
In that case, the driver transparently disables batching, resets
rx_buffers_per_hcall to 1, and falls back to the single-buffer hcall
in next future replenishments to take care of these and future buffers.
Test were done on systems with firmware that both supports and
does not support the new h_add_logical_lan_buffers hcall.
On supported firmware, this reduces hypercall overhead significantly
over multiple buffers. SAR measurements showed about a 15% improvement
in packet processing rate under moderate RX load, with heavier traffic
seeing gains more than 30%
Signed-off-by: Mingming Cao <mmc@linux.ibm.com>
Reviewed-by: Brian King <bjking1@linux.ibm.com>
Reviewed-by: Haren Myneni <haren@linux.ibm.com>
Reviewed-by: Dave Marquardt <davemarq@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250719091356.57252-1-mmc@linux.ibm.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Extract common ip6gre tunnel match from ip6gre_tunnel_lookup() into new
helper function ip6gre_tunnel_match() to reduce code duplication.
No functional change intended.
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250719081551.963670-1-yuehaibing@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Joshua Washington says:
====================
gve: AF_XDP zero-copy for DQO RDA
This patch series adds support for AF_XDP zero-copy in the DQO RDA queue
format.
XSK infrastructure is updated to re-post buffers when adding XSK pools
because XSK umem will be posted directly to the NIC, a departure from
the bounce buffer model used in GQI QPL. A registry of XSK pools is
introduced to prevent the usage of XSK pools when in copy mode.
v1: https://lore.kernel.org/netdev/20250714160451.124671-1-jeroendb@google.com/
====================
Link: https://patch.msgid.link/20250717152839.973004-1-jeroendb@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add the RX datapath for AF_XDP zero-copy for DQ RDA. The RX path is
quite similar to that of the normal XDP case. Parallel methods are
introduced to properly handle XSKs instead of normal driver buffers.
To properly support posting from XSKs, queues are destroyed and
recreated, as the driver was initially making use of page pool buffers
instead of the XSK pool memory.
Expose support for AF_XDP zero-copy, as the TX and RX datapaths both
exist.
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Praveen Kaligineedi <pkaligineedi@google.com>
Signed-off-by: Joshua Washington <joshwash@google.com>
Signed-off-by: Jeroen de Borst <jeroendb@google.com>
Link: https://patch.msgid.link/20250717152839.973004-6-jeroendb@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
In the descriptor clean path, a number of changes need to be made to
accommodate out of order completions and double completions.
The XSK stack can only handle completions being processed in order, as a
single counter is incremented in xsk_tx_completed to sigify how many XSK
descriptors have been completed. Because completions can come back out
of order in DQ, a separate queue of XSK descriptors must be maintained.
This queue keeps the pending packets in the order that they were written
so that the descriptors can be counted in xsk_tx_completed in the same
order.
For double completions, a new pending packet state and type are
introduced. The new type, GVE_TX_PENDING_PACKET_DQO_XSK, plays an
anlogous role to pre-existing _SKB and _XDP_FRAME pending packet types
for XSK descriptors. The new state, GVE_PACKET_STATE_XSK_COMPLETE,
represents packets for which no more completions are expected. This
includes packets which have received a packet completion or reinjection
completion, as well as packets whose reinjection completion timer have
timed out. At this point, such packets can be counted as part of
xsk_tx_completed() and freed.
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Praveen Kaligineedi <pkaligineedi@google.com>
Signed-off-by: Joshua Washington <joshwash@google.com>
Signed-off-by: Jeroen de Borst <jeroendb@google.com>
Link: https://patch.msgid.link/20250717152839.973004-5-jeroendb@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Relying on xsk_get_pool_from_qid for getting whether zero copy is
enabled on a queue is erroneous, as an XSK pool is registered in
xp_assign_dev whether AF_XDP zero-copy is enabled or not. This becomes
problematic when queues are restarted in copy mode, as all RX queues
with XSKs will register a pool, causing the driver to exercise the
zero-copy codepath.
This patch adds a bitmap to keep track of which queues have zero-copy
enabled.
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Joshua Washington <joshwash@google.com>
Signed-off-by: Jeroen de Borst <jeroendb@google.com>
Link: https://patch.msgid.link/20250717152839.973004-4-jeroendb@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The existence of both of these xdp_rxq and xsk_rxq is redundant. xdp_rxq
can be used in both the zero-copy mode and the copy mode case. XSK pool
memory model registration is prioritized over normal memory model
registration to ensure that memory model registration happens only once
per queue.
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Joshua Washington <joshwash@google.com>
Signed-off-by: Jeroen de Borst <jeroendb@google.com>
Link: https://patch.msgid.link/20250717152839.973004-3-jeroendb@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The XDP registration path currently has a lot of reused logic, leading
changes to the codepaths to be unnecessarily complex. gve_reg_xsk_pool
extracts the logic of registering an XSK pool with a queue into a method
that can be used by both XDP_SETUP_XSK_POOL and gve_reg_xdp_info.
gve_unreg_xdp_info is used to undo XDP info registration in the error
path instead of explicitly unregistering the XDP info, as it is more
complete and idempotent.
This patch will be followed by other changes to the XDP registration
logic, and will simplify those changes due to the use of common methods.
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Joshua Washington <joshwash@google.com>
Signed-off-by: Jeroen de Borst <jeroendb@google.com>
Link: https://patch.msgid.link/20250717152839.973004-2-jeroendb@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Jakub Kicinski says:
====================
ethtool: rss: support creating and removing contexts via Netlink
This series completes support of RSS configuration via Netlink.
All functionality supported by the IOCTL is now supported by
Netlink. Future series (time allowing) will add:
- hashing on the flow label, which started this whole thing;
- pinning the RSS context to a Netlink socket for auto-cleanup.
The first patch is a leftover held back from previous series
to avoid conflicting with Gal's fix.
Next 4 patches refactor existing code to make reusing it for
context creation possible. 2 patches after that add create
and delete commands. Last but not least the test is extended.
====================
Link: https://patch.msgid.link/20250717234343.2328602-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add test cases for creating and deleting contexts.
TAP version 13
1..12
ok 1 rss_api.test_rxfh_nl_set_fail
ok 2 rss_api.test_rxfh_nl_set_indir
ok 3 rss_api.test_rxfh_nl_set_indir_ctx
ok 4 rss_api.test_rxfh_indir_ntf
ok 5 rss_api.test_rxfh_indir_ctx_ntf
ok 6 rss_api.test_rxfh_nl_set_key
ok 7 rss_api.test_rxfh_fields
ok 8 rss_api.test_rxfh_fields_set
ok 9 rss_api.test_rxfh_fields_set_xfrm # SKIP no input-xfrm supported
ok 10 rss_api.test_rxfh_fields_ntf
ok 11 rss_api.test_rss_ctx_add
ok 12 rss_api.test_rss_ctx_ntf
# Totals: pass:11 fail:0 xfail:0 xpass:0 skip:1 error:0
Link: https://patch.msgid.link/20250717234343.2328602-9-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Implement removing additional RSS contexts via Netlink.
Technically it'd be possible to shoehorn the delete operation
into ethnl_request_ops-compatible handler. The code ends
up longer than open coded version, and I think we'll need
a custom way of sending notifications at some stage (if we
allow tying the context lifetime to the netlink socket, in
the future).
Link: https://patch.msgid.link/20250717234343.2328602-8-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Support creating contexts via Netlink. Setting flow hashing
fields on the new context is not supported at this stage,
it can be added later.
An empty indirection table is not supported. This is a carry
over from the IOCTL interface where empty indirection table
meant delete. We can repurpose empty indirection table in
Netlink but for now to avoid confusion reject it using the
policy.
Support letting user choose the ID for the new context. This was
not possible in IOCTL since the context ID field for the create
action had to be set to the ETH_RXFH_CONTEXT_ALLOC magic value.
Link: https://patch.msgid.link/20250717234343.2328602-7-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move ethtool_rxfh_ctx_alloc() to common code, Netlink will need it.
Reviewed-by: Gal Pressman <gal@nvidia.com>
Link: https://patch.msgid.link/20250717234343.2328602-6-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Similarly to previous change, factor out populating the response.
We will use this after the context was allocated to send a notification
so this time factor out from the additional context handling, rather
than context 0 handling (for request context didn't exist, for response
it does).
Reviewed-by: Gal Pressman <gal@nvidia.com>
Link: https://patch.msgid.link/20250717234343.2328602-5-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
To ease the code reuse for RSS_CREATE we'll want to prepare
struct rss_reply_data for the new context. Unfortunately
we can't depend on the exiting scaffolding because the context
doesn't exist (ctx=NULL) when we start preparing. Factor out
the portion of the context 0 handling responsible for allocation
of request memory, so that we can call it directly.
Link: https://patch.msgid.link/20250717234343.2328602-4-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In anticipation for CREATE and DELETE notifications - explicitly
pass the notification type to ethtool_rss_notify(), when calling
from the IOCTL code.
Reviewed-by: Gal Pressman <gal@nvidia.com>
Link: https://patch.msgid.link/20250717234343.2328602-3-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Supporting per-RSS context configuration of hashing fields but
not the hashing algorithm would complicate the code a lot.
We'd need to cross check the config against all RSS contexts.
None of the drivers need this today, so explicitly prevent
new drivers with such skewed capabilities from registering.
If such driver appears it will need to first adjust the checks
in the core.
Link: https://patch.msgid.link/20250717234343.2328602-2-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Matthieu Baerts says:
====================
mptcp: add TCP_MAXSEG sockopt support
The TCP_MAXSEG socket option was not supported by MPTCP, mainly because
it has never been requested before. But there are still valid use-cases,
e.g. with HAProxy.
- Patch 1 is a small cleanup patch in the MPTCP sockopt file.
- Patch 2 expose some code from TCP, to avoid duplicating it in MPTCP.
- Patch 3 adds TCP_MAXSEG sockopt support in MPTCP.
- Patch 4 is not related to the others, it fixes a typo in a comment.
Note that the new TCP_MAXSEG sockopt support has been validated by a new
packetdrill script on the MPTCP CI:
https://github.com/multipath-tcp/packetdrill/pull/161
v1: https://lore.kernel.org/20250716-net-next-mptcp-tcp_maxseg-v1-0-548d3a5666f6@kernel.org
====================
Link: https://patch.msgid.link/20250719-net-next-mptcp-tcp_maxseg-v2-0-8c910fbc5307@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch fixes the follow spelling mistake in a comment:
greter -> greater
Signed-off-by: moyuanhao <moyuanhao3676@163.com>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250719-net-next-mptcp-tcp_maxseg-v2-4-8c910fbc5307@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The TCP_MAXSEG socket option is currently not supported by MPTCP, mainly
because it has never been requested before. But there are still valid
use-cases, e.g. with HAProxy.
This patch adds its support in MPTCP by propagating the value to all
subflows. The get part looks at the value on the first subflow, to be as
closed as possible to TCP. Only one value can be returned for the cached
MSS, so this can come only from one subflow.
Similar to mptcp_setsockopt_first_sf_only(), a generic helper
mptcp_setsockopt_all_subflows() is added to set sockopt for each
subflows of the mptcp socket.
Add a new member for struct mptcp_sock to store the TCP_MAXSEG value,
and return this value in getsockopt.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/515
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250719-net-next-mptcp-tcp_maxseg-v2-3-8c910fbc5307@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a helper tcp_sock_set_maxseg() to directly set the TCP_MAXSEG
sockopt from kernel space.
This new helper will be used in the following patch from MPTCP.
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Acked-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250719-net-next-mptcp-tcp_maxseg-v2-2-8c910fbc5307@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
tcp_getsockopt() is called twice in mptcp_getsockopt_first_sf_only() in
different conditions, which makes the code a bit redundant.
The first call to tcp_getsockopt() when the first subflow exists can be
replaced by going to a new label "get" before the second call.
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250719-net-next-mptcp-tcp_maxseg-v2-1-8c910fbc5307@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update qeth driver to allow writing an existing value to the "hw_trap"
sysfs attribute. Attempting such a write earlier resulted in -EINVAL.
In other words, make the sysfs attribute idempotent.
After:
$ cat hw_trap
disarm
$ echo disarm > hw_trap
$
Suggested-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Aswin Karuvally <aswin@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250718141711.1141049-1-wintera@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The Wake-on-LAN (WoL) functionality for the QCA807x series is identical
to that of the AT8031. WoL support for QCA807x is enabled by utilizing
the at8031_set_wol() function provided in the shared library.
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Luo Jie <quic_luoj@quicinc.com>
Link: https://patch.msgid.link/20250718-qca807x_wol_support-v1-1-cfe323cbb4e8@quicinc.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Implement ethtool .get_pauseparam and .set_pauseparam handlers for
configuring flow control on smsc95xx. The driver now supports enabling
or disabling transmit and receive pause frames, with or without
autonegotiation. Pause settings are applied during link-up based on
current PHY state and user configuration.
Previously, the driver used phy_get_pause() during link-up handling,
but lacked initialization and an ethtool interface to configure pause
modes. As a result, flow control support was effectively non-functional.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250718075157.297923-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2025-07-18 (idpf, ice, igc, igbvf, ixgbevf)
For idpf:
Ahmed and Sudheer add support for flow steering via ntuple filters.
Current support is for IPv4 and TCP/UDP only.
Milena adds support for cross timestamping.
Ahmed preserves coalesce settings across resets.
For ice:
Alex adds reporting of 40GbE speed in devlink port split.
Dawid adds support for E835 devices.
Jesse refactors profile ptype processing for cleaner, more readable,
code.
Dave adds a couple of helper functions for LAG to reduce code
duplication.
For igc:
Siang adds support to configure "Default Queue" during runtime using
ethtool's Network Flow Classification (NFC) wildcard rule approach.
For igbvf:
Yuto Ohnuki removes unused fields from igbvf_adapter.
For ixgbevf:
Yuto Ohnuki removes unused fields from ixgbevf_adapter.
* '200GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
ixgbevf: remove unused fields from struct ixgbevf_adapter
igbvf: remove unused fields from struct igbvf_adapter
igc: Add wildcard rule support to ethtool NFC using Default Queue
igc: Relocate RSS field definitions to igc_defines.h
ice: breakout common LAG code into helpers
ice: convert ice_add_prof() to bitmap
ice: add E835 device IDs
ice: add 40G speed to Admin Command GET PORT OPTION
idpf: preserve coalescing settings across resets
idpf: add cross timestamping
idpf: add flow steering support
virtchnl2: add flow steering support
virtchnl2: rename enum virtchnl2_cap_rss
====================
Link: https://patch.msgid.link/20250718185118.2042772-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If the decice does not support filtering, filtering
must not be used and all packets delivered for the
upper layers to sort.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://patch.msgid.link/20250717120649.2090929-1-oneukum@suse.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add PM suspend/resume callbacks for RZ/G3E SMARC EVK.
The PM deep entry is executed by pressing the SLEEP button and exit from
entry is by pressing the power button.
Logs:
root@smarc-rzg3e:~# PM: suspend entry (deep)
Filesystems sync: 0.115 seconds
Freezing user space processes
Freezing user space processes completed (elapsed 0.002 seconds)
OOM killer disabled.
Freezing remaining freezable tasks
Freezing remaining freezable tasks completed (elapsed 0.001 seconds)
printk: Suspending console(s) (use no_console_suspend to debug)
NOTICE: BL2: v2.10.5(release):2.10.5/rz_soc_dev-162-g7148ba838
NOTICE: BL2: Built : 14:23:58, Jul 5 2025
NOTICE: BL2: SYS_LSI_MODE: 0x13e06
NOTICE: BL2: SYS_LSI_DEVID: 0x8679447
NOTICE: BL2: SYS_LSI_PRR: 0x0
NOTICE: BL2: Booting BL31
renesas-gbeth 15c30000.ethernet end0: Link is Down
Disabling non-boot CPUs ...
psci: CPU3 killed (polled 0 ms)
psci: CPU2 killed (polled 0 ms)
psci: CPU1 killed (polled 0 ms)
Enabling non-boot CPUs ...
Detected VIPT I-cache on CPU1
GICv3: CPU1: found redistributor 100 region 0:0x0000000014960000
CPU1: Booted secondary processor 0x0000000100 [0x412fd050]
CPU1 is up
Detected VIPT I-cache on CPU2
GICv3: CPU2: found redistributor 200 region 0:0x0000000014980000
CPU2: Booted secondary processor 0x0000000200 [0x412fd050]
CPU2 is up
Detected VIPT I-cache on CPU3
GICv3: CPU3: found redistributor 300 region 0:0x00000000149a0000
CPU3: Booted secondary processor 0x0000000300 [0x412fd050]
CPU3 is up
dwmac4: Master AXI performs fixed burst length
15c30000.ethernet end0: No Safety Features support found
15c30000.ethernet end0: IEEE 1588-2008 Advanced Timestamp supported
15c30000.ethernet end0: configuring for phy/rgmii-id link mode
dwmac4: Master AXI performs fixed burst length
15c40000.ethernet end1: No Safety Features support found
15c40000.ethernet end1: IEEE 1588-2008 Advanced Timestamp supported
15c40000.ethernet end1: configuring for phy/rgmii-id link mode
OOM killer enabled.
Restarting tasks: Starting
Restarting tasks: Done
random: crng reseeded on system resumption
PM: suspend exit
15c30000.ethernet end0: Link is Up - 1Gbps/Full - flow control rx/tx
root@smarc-rzg3e:~# ifconfig end0 192.168.10.7 up
root@smarc-rzg3e:~# ping 192.168.10.1
PING 192.168.10.1 (192.168.10.1) 56(84) bytes of data.
64 bytes from 192.168.10.1: icmp_seq=1 ttl=64 time=2.05 ms
64 bytes from 192.168.10.1: icmp_seq=2 ttl=64 time=0.928 ms
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://patch.msgid.link/20250717071109.8213-1-biju.das.jz@bp.renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Raju Rangoju says:
====================
amd-xgbe: add hardware PTP timestamping
Remove the hwptp abstraction and associated callbacks from the
struct xgbe_hw_if {} and move them to separate file after cleanup.
Adds complete support for hardware-based PTP (IEEE 1588)
timestamping to the AMD XGBE driver.
====================
Link: https://patch.msgid.link/20250718185628.4038779-1-Raju.Rangoju@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Adds complete support for hardware-based PTP (IEEE 1588)
timestamping to the AMD XGBE driver.
- Initialize and configure the MAC PTP registers based on link
speed and reference clock.
- Support both 50MHz and 125MHz PTP reference clocks.
- Update the driver interface and version data to support PTP
clock frequency selection.
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Link: https://patch.msgid.link/20250718185628.4038779-3-Raju.Rangoju@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove the hwptp abstraction and associated callbacks from
the struct xgbe_hw_if {}.
The callback structure was only ever assigned a single function, without
null checks. This cleanup inlines the logic and moves all the hwtstamp
realted code a separate file, improving readability and maintainance.
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Link: https://patch.msgid.link/20250718185628.4038779-2-Raju.Rangoju@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add test cases to tc_flower.sh to validate generic matching on ERSPAN
options. Both ERSPAN Type II and Type III are covered.
Also add check_tc_erspan_support() to verify whether tc supports
erspan_opts.
Signed-off-by: Li Shuang <shuali@redhat.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Link: https://patch.msgid.link/1f354a1afd60f29bbbf02bd60cb52ecfc0b6bd17.1752848172.git.shuali@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This commit remove duplicate assignments for net->pcpu_stat_type
in usbnet_probe().
Signed-off-by: Zqiang <qiang.zhang@linux.dev>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce new "cable_length" field in PFCC register and related fields
to enhance rx buffer configuration management:
1. cable_length: Shifts cable length handling to fw by storing a
manually entered length from user in PFCC.cable_length
2. lane_rate_oper: In a case where PFCC.cable_length is not supported,
helps compute a default cable length
Signed-off-by: Oren Sidi <osidi@nvidia.com>
Reviewed-by: Alex Lazar <alazar@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1752734895-257735-4-git-send-email-tariqt@nvidia.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
Extend structure layouts and defines buf_ownership.
buf_ownership indicates whether the buffer is managed by SW or FW.
Signed-off-by: Oren Sidi <osidi@nvidia.com>
Reviewed-by: Alex Lazar <alazar@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1752734895-257735-3-git-send-email-tariqt@nvidia.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
This adds the capabilities, ipsec_next_header and inner/outer
l4_type_ext fields to support RSS for the decrypted packets.
These fields are specifically for firmware steering. HWS validation
logic is updated to correctly handle the changes, ensuring the
unsupported fields are not set.
Besides, reserved_at_c4 is fixed to reserved_at_d4 to reflect the
accurate offset within the structure.
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1752734895-257735-2-git-send-email-tariqt@nvidia.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
The TCP header fields seq and ack_seq are 32-bit values in network
byte order as (__be32). these fields were earlier printed using
ntohs(), which converts only 16-bit values and produces incorrect
results for 32-bit fields. This patch is changeing the conversion
to ntohl(), ensuring correct interpretation of these sequence numbers.
Notably, the format specifier is updated from %d to %u to reflect the
unsigned nature of these fields.
improves the accuracy of debug log messages for TCP sequence and
acknowledgment numbers during TX timeouts.
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250717193552.3648791-1-alok.a.tiwari@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Wire-up ethtool_ops::nway_reset to phy_ethtool_nway_reset in order to
support re-starting auto-negotiation.
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250717180915.2611890-1-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Stanislav Fomichev says:
====================
net: maintain netif vs dev prefix semantics
Commit cc34acd577f1 ("docs: net: document new locking reality")
introduced netif_ vs dev_ function semantics: the former expects locked
netdev, the latter takes care of the locking. We don't strictly
follow this semantics on either side, but there are more dev_xxx handlers
now that don't fit. Rename them to netif_xxx where appropriate. We care only
about driver-visible APIs, don't touch stack-internal routines.
The rest seem to be ok:
* dev_xdp_prog_count - mostly called by sw drivers (bonding), should not matter
* dev_get_by_xxx - too many to reasonably cleanup, already have different flavors
* dev_fetch_sw_netstats - don't need instance lock
* dev_get_tstats64 - never called directly, only as an ndo callback
* dev_pick_tx_zero - never called directly, only as an ndo callback
* dev_add_pack / dev_remove_pack - called early enough (in module init) to not matter
* dev_get_iflink - mostly called by sw drivers, should not matter
* dev_fill_forward_path - ditto
* dev_getbyhwaddr_rcu - ditto
* dev_getbyhwaddr - ditto
* dev_getfirstbyhwtype - ditto
* dev_valid_name - ditto
* __dev_forward_skb dev_forward_skb dev_queue_xmit_nit - established helpers, no netif vs dev distinction
====================
Link: https://patch.msgid.link/20250717172333.1288349-1-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit cc34acd577f1 ("docs: net: document new locking reality")
introduced netif_ vs dev_ function semantics: the former expects locked
netdev, the latter takes care of the locking. We don't strictly
follow this semantics on either side, but there are more dev_xxx handlers
now that don't fit. Rename them to netif_xxx where appropriate.
netif_close_many is used only by vlan/dsa and one mtk driver, so move it into
NETDEV_INTERNAL namespace.
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20250717172333.1288349-8-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit cc34acd577f1 ("docs: net: document new locking reality")
introduced netif_ vs dev_ function semantics: the former expects locked
netdev, the latter takes care of the locking. We don't strictly
follow this semantics on either side, but there are more dev_xxx handlers
now that don't fit. Rename them to netif_xxx where appropriate.
Note that one dev_set_threaded call still remains in mt76 for debugfs file.
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20250717172333.1288349-7-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit cc34acd577f1 ("docs: net: document new locking reality")
introduced netif_ vs dev_ function semantics: the former expects locked
netdev, the latter takes care of the locking. We don't strictly
follow this semantics on either side, but there are more dev_xxx handlers
now that don't fit. Rename them to netif_xxx where appropriate.
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20250717172333.1288349-6-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit cc34acd577f1 ("docs: net: document new locking reality")
introduced netif_ vs dev_ function semantics: the former expects locked
netdev, the latter takes care of the locking. We don't strictly
follow this semantics on either side, but there are more dev_xxx handlers
now that don't fit. Rename them to netif_xxx where appropriate.
__netif_set_mtu is used only by bond, so move it into
NETDEV_INTERNAL namespace.
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20250717172333.1288349-5-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit cc34acd577f1 ("docs: net: document new locking reality")
introduced netif_ vs dev_ function semantics: the former expects locked
netdev, the latter takes care of the locking. We don't strictly
follow this semantics on either side, but there are more dev_xxx handlers
now that don't fit. Rename them to netif_xxx where appropriate.
netif_pre_changeaddr_notify is used only by ipvlan/bond, so move it into
NETDEV_INTERNAL namespace.
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20250717172333.1288349-4-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit cc34acd577f1 ("docs: net: document new locking reality")
introduced netif_ vs dev_ function semantics: the former expects locked
netdev, the latter takes care of the locking. We don't strictly
follow this semantics on either side, but there are more dev_xxx handlers
now that don't fit. Rename them to netif_xxx where appropriate.
netif_get_mac_address is used only by tun/tap, so move it into
NETDEV_INTERNAL namespace.
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20250717172333.1288349-3-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit cc34acd577f1 ("docs: net: document new locking reality")
introduced netif_ vs dev_ function semantics: the former expects locked
netdev, the latter takes care of the locking. We don't strictly
follow this semantics on either side, but there are more dev_xxx handlers
now that don't fit. Rename them to netif_xxx where appropriate.
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20250717172333.1288349-2-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Virtual devices (e.g., VXLAN) that do not have a notion of a carrier are
created with an "UNKNOWN" operational state which some users find
confusing [1].
It is possible to set the operational state from user space either
during device creation or afterwards and some applications will start
doing that in order to avoid the above problem.
Add a test for this functionality to ensure it does not regress.
[1] https://lore.kernel.org/netdev/20241119153703.71f97b76@hermes.local/
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250717125151.466882-1-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Detect NICs and drivers that either drop frames with a corrupted TCP
checksum or, worse, pass them up as valid. The test flips one bit in
the checksum, transmits the packet in internal loopback, and fails when
the driver reports CHECKSUM_UNNECESSARY.
Discussed at:
https://lore.kernel.org/all/20250625132117.1b3264e8@kernel.org/
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250717083524.1645069-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a new SKB drop reason (SKB_DROP_REASON_PFMEMALLOC) to track packets
dropped due to memory pressure. In production environments, we've observed
memory exhaustion reported by memory layer stack traces, but these drops
were not properly tracked in the SKB drop reason infrastructure.
While most network code paths now properly report pfmemalloc drops, some
protocol-specific socket implementations still use sk_filter() without
drop reason tracking:
- Bluetooth L2CAP sockets
- CAIF sockets
- IUCV sockets
- Netlink sockets
- SCTP sockets
- Unix domain sockets
These remaining cases represent less common paths and could be converted
in a follow-up patch if needed. The current implementation provides
significantly improved observability into memory pressure events in the
network stack, especially for key protocols like TCP and UDP, helping to
diagnose problems in production environments.
Reported-by: Matt Fleming <mfleming@cloudflare.com>
Signed-off-by: Jesper Dangaard Brouer <hawk@kernel.org>
Link: https://patch.msgid.link/175268316579.2407873.11634752355644843509.stgit@firesoul
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
