| Age | Commit message (Collapse) | Author |
|---|
|
The FS needs to be inverted in McASP compared to other supported formats.
Use a flag to indicate if the FS needs to be inverted.
At the same time fail when non supported format is asked since the default
case was anyways configuring McASP to a not valid format.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
FS polarity can be either rising or falling edge in McASP. Instead of
accessing the registers in every switch/case set a flag and write the
registers after the switch for the invert configuration.
This change will help when adding support for more formats also.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
DSP_A is like DSP_B mode but with one bit delay after the FS.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Use intermediate variable for the data delay needed for the specific format
and write the register after the format configuration at once.
This will help to control the number of lines as support for more formats
going to be added.
Also fixes a case when we switch between two formats with different delay
requirements.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
When the AFIFO is not enabled but more than one serializers are used the DMA
need to transfer number of words equal to active serializers when a DMA
request is generated.
When configuring the burst for the DMA avoid using value '1' for the burst
since it is going to enable additional logic in the DMA drivers. Burst '1'
means that the DMA should send/receive one word per DMA requests.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
(dynamic depth)
Configure the AFIFO numevt parameter based on the requested tx/rx_numevt,
active serializers and period size in words.
In this way McASP can adopt it's (and the DMA) configuration runtime and
can pick the most optimal setup which satisfy the parameters.
This way we do not need to place any constraint on the stream itself,
allowing application greater freedom on how they want to set up ALSA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Move the dma_params->fifo_level and dma_data->maxburst configuration to the
mcasp_common_hw_param() function where we configure the AFIFO registers.
It makes the code regarding to AFIFO and DMA configuration more easy to
follow since it is now clear how the AFIFO and how the DMA is going to be
configured.
Previously this has been done in two functions using a bit different
calculation form - which ended up with the same result in both case at the
end, but it was confusing.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
We can have more linear code flow by using variables in
mcasp_common_hw_param() related to the AFIFO configuration.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
requred -> required
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Set up the playback_dma_data/capture_dma_data for the dai at probe
time since the generic dmaengine PCM stack needs to have access to
this information early.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
To save drivers using davinci-pcm and edma-pcm the need to fiddle with
!CONFIG_SND_DAVINCI_SOC in their code.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Change reg's type from unsigned short to unsigned int. So that we can use
32 bits reg value in snd_soc_update_bits.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Signed-off-by: Nariman Poushin <nariman@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Signed-off-by: Nariman Poushin <nariman@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
There is an increasing amount of code that is very similar between platforms,
CODECS and other components. Making platforms a component will allow us to
share this code. For now the patch just adds component and component_driver
fields to the platform and platform_driver structs and registers the platform as
a component. Followup patches will be used to consolidate code between the
different types of components.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
snd_soc_register_component()
snd_soc_unregister_component() takes the parent device of the component as a
parameter and then looks up the component based on this. This is a problem if
multiple components are registered for the same parent device. Currently drivers
do not do this, but some drivers register a CPU DAI component and a platform for
the same parent device. This will become a problem once platforms are also made
components. To make sure that snd_soc_unregister_component() will not
accidentally unregister the platform in such a case only consider components
that were registered with snd_soc_register_component(). This is only meant as
short term stopgap solution to be able to continue componentisation. Long term
we'll need something different.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
There are no ASoC drivers left that use them and new drivers are supposed to use
regmap for this.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
soc-core.c is getting quite crowded. Move all IO related functions that are
still in soc-core.c to soc-io.c
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
SOC_SINGLE_XR_SX controls currently only work with CODECs that set the
'reg_word_size' field in their snd_soc_codec_driver struct. Going forward
support for ASoC level IO will eventually be removed and all drivers will be
converted to regmap. Preparing for the transition this patch adds support for
CODECs using regmap for IO to the SOC_SINGLE_XR_SX control. We already have the
val_bytes field in the CODEC struct which holds the number of bytes per word,
but it is only initialized when regmap is used. Also initialize it for drivers
still using legacy IO and update the SOC_SINGLE_XR_SX handlers to use it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
For platform controls snd_kcontrol_chip() currently returns a pointer to the
platform that registered the control. With the upcoming consolidation of
platform and CODEC controls this will change. Prepare for this by introducing
the snd_soc_kcontrol_platform() helper function that will hide the
implementation details of how the platform for a control can be obtained. This
will allow us to change this easily in the future.
The patch also updates all platforms to use this new helper function.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
For CODEC controls snd_kcontrol_chip() currently returns a pointer to the
CODEC that registered the control. With the upcoming consolidation of
platform and CODEC controls this will change. Prepare for this by introducing
the snd_soc_kcontrol_codec() helper function that will hide the implementation
details of how the CODEC for a control can be obtained. This will allow us to
change this easily in the future.
The patch also updates all CODEC drivers to use the new helper function.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Some thing Likes:
reproduce: make C=1 CF=-D__CHECK_ENDIAN__
sparse warnings: (new ones prefixed by >>)
>> sound/soc/codecs/wm8997.c:1084:15: sparse: symbol \
'wm8997_get_regmap' was not declared. Should it be static?
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
As we can set the CODEC I/O while snd_soc_register_codec(), so the
calling of set_cache_io() from CODEC ASoC probe could be removed
entirely.
And then we can set the CODEC I/O in the device probe instead of
CODEC ASoC probe as earily as possible.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
As we can set the CODEC I/O while snd_soc_register_codec(), so the
calling of set_cache_io() from CODEC ASoC probe could be removed
entirely.
And then we can set the CODEC I/O in the device probe instead of
CODEC ASoC probe as earily as possible.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
As we can set the CODEC I/O while snd_soc_register_codec(), so the
calling of set_cache_io() from CODEC ASoC probe could be removed
entirely.
And then we can set the CODEC I/O in the device probe instead of
CODEC ASoC probe as earily as possible.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
As we can set the CODEC I/O while snd_soc_register_codec(), so the
calling of set_cache_io() from CODEC ASoC probe could be removed
entirely.
And then we can set the CODEC I/O in the device probe instead of
CODEC ASoC probe as earily as possible.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
As we can set the CODEC I/O while snd_soc_register_codec(), so the
calling of set_cache_io() from CODEC ASoC probe could be removed
entirely.
And then we can set the CODEC I/O in the device probe instead of
CODEC ASoC probe as earily as possible.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
As we can set the CODEC I/O while snd_soc_register_codec(), so the
calling of set_cache_io() from CODEC ASoC probe could be removed
entirely.
And then we can set the CODEC I/O in the device probe instead of
CODEC ASoC probe as earily as possible.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
As we can set the CODEC I/O while snd_soc_register_codec(), so the
calling of set_cache_io() from CODEC ASoC probe could be removed
entirely.
And then we can set the CODEC I/O in the device probe instead of
CODEC ASoC probe as earily as possible.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Acked-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
As we can set the CODEC I/O while snd_soc_register_codec(), so the
calling of set_cache_io() from CODEC ASoC probe could be removed
entirely.
And then we can set the CODEC I/O in the device probe instead of
CODEC ASoC probe as earily as possible.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
As we can set the CODEC I/O while snd_soc_register_codec(), so the
calling of set_cache_io() from CODEC ASoC probe could be removed
entirely.
And then we can set the CODEC I/O in the device probe instead of
CODEC ASoC probe as earily as possible.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
As we can set the CODEC I/O while snd_soc_register_codec(), so the
calling of set_cache_io() from CODEC ASoC probe could be removed
entirely.
And then we can set the CODEC I/O in the device probe instead of
CODEC ASoC probe as earily as possible.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Add the default regmap I/O setting to snd_soc_register_codec() while
the CODEC is initialising, which will be called by CODEC driver device
probe(), and then we can make XXX_set_cache_io() go away entirely from each
CODEC ASoC probe.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
There are no OSR controls on outputs 1-4 on wm5110, however when these
were removed the ones on output 5 and 6 were also accidentally removed,
but those actually exist. This patch adds these controls back in.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Conflicts:
tools/perf/bench/numa.c
Pull perf fixes from Jiri Olsa.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Pick up the latest fixes.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Avoid colision with regmap's struct reg_field definition by renaming
omapdss's struct reg_field to dispc_reg_field, and moving it inside
dispc.c as that's the only place it is used.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Pixelclock unit change from kHz to Hz should be taken into account
in CTS value calculations in hdmi_compute_acr().
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
udelay with more than 20000 may cause __bad_udelay.
Use mdelay for instead.
[fixed a typo spotted by Clemens -- tiwai]
Signed-off-by: Li, Zhen-Hua <zhen-hual@hp.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
DSS uses shared irq handlers for DISPC and DSI, because on OMAP3, the
DISPC and DSI share the same irq line.
However, the irq handlers presume that the hardware is enabled, which,
in theory, may not be the case with shared irq handlers. So if an
interrupt happens while the DISPC/DSI is off, the kernel will halt as
the irq handler tries to access the DISPC/DSI registers.
In practice that should never happen, as both DSI and DISPC are in the
same power domain. So if there's an IRQ for one of them, the other is
also enabled. However, if CONFIG_DEBUG_SHIRQ is enabled, the kernel will
generate a spurious IRQ, which then causes the problem.
This patch adds an is_enabled field for both DISPC and DSI, which is
used to track if the HW is enabled. For DISPC the code is slightly more
complex, as the users of DISPC can register the interrupt handler, and
we want to hide the is_enabled handling from the users of DISPC.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
FB driver uses lowlevel controls for LCD powering and contrast changing.
Since LCD class cannot be used as an optional feature and should be
compiled for using in the driver, this patch selects LCD_CLASS_DEVICE
symbol for the driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
"clk: divider: fix rate calculation for fractional rates" patch (and
similar for TI specific divider) fixes the clk-divider's rounding. This
patch updates the DSS driver to round the rates accordingly.
This fixes the DSS's warnings about clock rate mismatch, and also fixes
the wrong fclk rate being set.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Christoph Fritz <chf.fritz@googlemail.com>
Tested-by: Marek Belisko <marek@goldelico.com>
|
|
The casting to (u16 *) on info->pseudo_palette is wrong and causes the
display to show a blue (garbage) vertical line on every other pixel column
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sashal/linux into core/urgent
Pull liblockdep fixes from Sasha Levin:
" 1. There was a build breakage caused by marking a function 'asmlinkage'
in lockdep.h. Fix that by ignoring asmlinkage and visible annotations.
2. Josh Boyer mentioned that Fedora would like to include liblockdep
as a package, so we had to fix our versioning methods from being dumb
and pointless to something actually usable. So now liblockdep.so tracks
the kernel version which makes lives of distro folks much easier. "
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
perf stat did initialize the stats structure used to compute
stddev etc. incorrectly. It merely zeroes it. But one member
(min) needs to be set to a non zero value. This causes min
to be not computed at all. Call init_stats() correctly.
It doesn't matter for stat currently because it doesn't use
min, but it's still better to do it correctly.
The other users of statistics are already correct.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Link: http://lkml.kernel.org/r/1395768699-16060-1-git-send-email-andi@firstfloor.org
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
|
|
Currently,
$ perf bench numa mem
errors out with usage information. To make this more user-friendly, let
us provide a minimum set of default values required for a test
run. As an added bonus,
$ perf bench all
now goes all the way to completion.
Signed-off-by: Ramkumar Ramachandra <artagnon@gmail.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/1395964219-22173-2-git-send-email-artagnon@gmail.com
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
|
|
At the end of
$ perf bench all
the program segfaults because it attempts to dereference a NULL
pointer. Fix this fault.
Signed-off-by: Ramkumar Ramachandra <artagnon@gmail.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/1395964219-22173-4-git-send-email-artagnon@gmail.com
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
|
|
Signed-off-by: Ramkumar Ramachandra <artagnon@gmail.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/1395964219-22173-3-git-send-email-artagnon@gmail.com
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
|
|
The dwarf_getcfi() only checks .debug_frame section for CFI, but as
most binaries only have .eh_frame it'd return NULL and it makes
some variables inaccessible.
Using dwarf_getcfi_elf (along with dwarf_getelf()) allows to show and
add probe to more variables.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Link: http://lkml.kernel.org/r/1396854348-9296-1-git-send-email-namhyung@kernel.org
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
|
|
As Namhyung reported(https://lkml.org/lkml/2014/4/1/89),
current perf-probe -L option doesn't handle errors in line-range
searching correctly. It causes a SEGV if an error occured in the
line-range searching.
----
$ perf probe -x ./perf -v -L map__load
Open Debuginfo file: /home/namhyung/project/linux/tools/perf/perf
fname: util/map.c, lineno:153
New line range: 153 to 2147483647
path: (null)
Segmentation fault (core dumped)
----
This is because line_range_inline_cb() ignores errors
from find_line_range_by_line() which means that lr->path is
already freed on the error path in find_line_range_by_line().
As a result, get_real_path() accesses the lr->path and it
causes a NULL pointer exception.
This fixes line_range_inline_cb() to handle the error correctly,
and report it to the caller.
Anyway, this just fixes a possible SEGV bug, Namhyung's patch
is also required.
Reported-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung.kim@lge.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20140402054831.19080.27006.stgit@ltc230.yrl.intra.hitachi.co.jp
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
|
