| Age | Commit message (Collapse) | Author |
|---|
|
Add DT entries for the phy mode selection in AM33xx SoC using cpsw-phy-sel
driver.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Phy mode can be configured via the cpsw-phy-sel driver, this patch enabled the
cpsw driver to utilise the api provided by the cpsw-phy-sel driver to configure
the phy mode.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The cpsw currently lacks code to properly set up the hardware interface
mode on AM33xx. Other platforms might be equally affected.
Usually, the bootloader will configure the control module register, so
probably that's why such support wasn't needed in the past. In suspend
mode though, this register is modified, and so it needs reprogramming
after resume.
This patch adds a new driver in which hardware interface can configure
correct register bits when the slave is opened.
The AM33xx also has a bit for each slave to configure the RMII reference
clock direction. Setting it is now supported by a per-slave DT property.
This code path introducted by this patch is currently exclusive for
am33xx and same can be extened to various platforms via the DT compatibility
property.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch cleans up the allocation and error unwind paths, which
allows us to carry less information in struct cpsw_priv and reduce the
amount of jump labels in the probe functions.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In my patch c194992cbe71c20bb3623a566af8d11b0bfaa721 ("skge: fix
broken driver") I didn't fix the skge bug correctly. The value of the
new mapping (not old) was passed to pci_unmap_single.
If we enable CONFIG_DMA_API_DEBUG, it results in this warning:
WARNING: CPU: 0 PID: 0 at lib/dma-debug.c:986 check_sync+0x4c4/0x580()
skge 0000:02:07.0: DMA-API: device driver tries to sync DMA memory it has
not allocated [device address=0x000000023a0096c0] [size=1536 bytes]
This patch makes the skge driver pass the correct value to
pci_unmap_single and fixes the warning. It copies the old descriptor to
on-stack variable "ee" and unmaps it if mapping of the new descriptor
succeeded.
This patch should be backported to 3.11-stable.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reported-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Redirect isn't an error condition, it should leave
the error handler without touching the socket.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Redirect isn't an error condition, it should leave
the error handler without touching the socket.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are a mix of function prototypes with and without extern
in the kernel sources. Standardize on not using extern for
function prototypes.
Function prototypes don't need to be written with extern.
extern is assumed by the compiler. Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Signed-off-by: Joe Perches <joe@perches.com>
|
|
There are a mix of function prototypes with and without extern
in the kernel sources. Standardize on not using extern for
function prototypes.
Function prototypes don't need to be written with extern.
extern is assumed by the compiler. Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are a mix of function prototypes with and without extern
in the kernel sources. Standardize on not using extern for
function prototypes.
Function prototypes don't need to be written with extern.
extern is assumed by the compiler. Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are a mix of function prototypes with and without extern
in the kernel sources. Standardize on not using extern for
function prototypes.
Function prototypes don't need to be written with extern.
extern is assumed by the compiler. Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are a mix of function prototypes with and without extern
in the kernel sources. Standardize on not using extern for
function prototypes.
Function prototypes don't need to be written with extern.
extern is assumed by the compiler. Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are a mix of function prototypes with and without extern
in the kernel sources. Standardize on not using extern for
function prototypes.
Function prototypes don't need to be written with extern.
extern is assumed by the compiler. Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are a mix of function prototypes with and without extern
in the kernel sources. Standardize on not using extern for
function prototypes.
Function prototypes don't need to be written with extern.
extern is assumed by the compiler. Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are a mix of function prototypes with and without extern
in the kernel sources. Standardize on not using extern for
function prototypes.
Function prototypes don't need to be written with extern.
extern is assumed by the compiler. Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are a mix of function prototypes with and without extern
in the kernel sources. Standardize on not using extern for
function prototypes.
Function prototypes don't need to be written with extern.
extern is assumed by the compiler. Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are a mix of function prototypes with and without extern
in the kernel sources. Standardize on not using extern for
function prototypes.
Function prototypes don't need to be written with extern.
extern is assumed by the compiler. Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are two locks involved in managing the journal lists. The general
reiserfs_write_lock and the journal->j_flush_mutex.
While flush_journal_list is sleeping to acquire the j_flush_mutex or to
submit a block for write, it will drop the write lock. This allows
another thread to acquire the write lock and ultimately call
flush_used_journal_lists to traverse the list of journal lists and
select one for flushing. It can select the journal_list that has just
had flush_journal_list called on it in the original thread and call it
again with the same journal_list.
The second thread then drops the write lock to acquire j_flush_mutex and
the first thread reacquires it and continues execution and eventually
clears and frees the journal list before dropping j_flush_mutex and
returning.
The second thread acquires j_flush_mutex and ends up operating on a
journal_list that has already been released. If the memory hasn't
been reused, we'll soon after hit a BUG_ON because the transaction id
has already been cleared. If it's been reused, we'll crash in other
fun ways.
Since flush_journal_list will synchronize on j_flush_mutex, we can fix
the race by taking a proper reference in flush_used_journal_lists
and checking to see if it's still valid after the mutex is taken. It's
safe to iterate the list of journal lists and pick a list with
just the write lock as long as a reference is taken on the journal list
before we drop the lock. We already have code to handle whether a
transaction has been flushed already so we can use that to handle the
race and get rid of the trans_id BUG_ON.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Commit a3172027 introduced test_transaction as a requirement for
flushing old lists -- but it can never return 1 unless the transaction
has already been flushed.
As a result, we have a routine that iterates the j_realblocks list but
doesn't actually do anything. Since it's been this way since 2006 and
the latency numbers were what Chris expected, let's just rip it out.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
A user has reported an oops in udf_statfs() that was caused by
numOfPartitions entry in LVID structure being corrupted. Fix the problem
by verifying whether numOfPartitions makes sense at least to the extent
that LVID fits into a single block as it should.
Reported-by: Juergen Weigert <jw@suse.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
No support for MIPS53 processors yet.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5876/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
In
commit edc3d8848dc9fe2a470316363dab8ef211d77e01
Author: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Date: Thu May 23 13:55:35 2013 +0300
drm/i915: avoid big kmallocs on reading error state
we introduce a two-pass mechanism for splitting long strings being
formatted into the error-state. The first pass finds the length, and the
second pass emits the right portion of the string into the accumulation
buffer. Unfortunately we use the same va_list for both passes, resulting
in the second pass reading garbage off the end of the argument list. As
the two passes are only used for boundaries between read() calls, the
corruption is only rarely seen.
This fixes the root cause behind
commit baf27f9b17bf2f369f3865e38c41d2163e8d815d
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Sat Jun 29 23:26:50 2013 +0100
drm/i915: Break up the large vsnprintf() in print_error_buffers()
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Set SEL control urbs cannot be sent to a device in unconfigured state.
This patch adds a check in usb_req_set_sel() to ensure the usb device's
state is USB_STATE_CONFIGURED.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Reported-by: Martin MOKREJS <mmokrejs@gmail.com>
Suggested-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
|
|
The halted state of a endpoint cannot be cleared over CLEAR_HALT from a
user process, because the stopped_td variable was overwritten in the
handle_stopped_endpoint() function. So the xhci_endpoint_reset() function will
refuse the reset and communication with device can not run over this endpoint.
https://bugzilla.kernel.org/show_bug.cgi?id=60699
Signed-off-by: Florian Wolter <wolly84@web.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
|
|
When a device signals remote wakeup on a roothub, and the suspend change
bit is set, the host controller driver must not give control back to the
USB core until the port goes back into the active state.
EHCI accomplishes this by waiting in the get port status function until
the PORT_RESUME bit is cleared:
/* stop resume signaling */
temp &= ~(PORT_RWC_BITS | PORT_SUSPEND | PORT_RESUME);
ehci_writel(ehci, temp, status_reg);
clear_bit(wIndex, &ehci->resuming_ports);
retval = ehci_handshake(ehci, status_reg,
PORT_RESUME, 0, 2000 /* 2msec */);
Similarly, the xHCI host should wait until the port goes into U0, before
passing control up to the USB core. When the port transitions from the
RExit state to U0, the xHCI driver will get a port status change event.
We need to wait for that event before passing control up to the USB
core.
After the port transitions to the active state, the USB core should time
a recovery interval before it talks to the device. The length of that
recovery interval is TRSMRCY, 10 ms, mentioned in the USB 2.0 spec,
section 7.1.7.7. The previous xHCI code (which did not wait for the
port to go into U0) would cause the USB core to violate that recovery
interval.
This bug caused numerous USB device disconnects on remote wakeup under
ChromeOS and a Lynx Point LP xHCI host that takes up to 20 ms to move
from RExit to U0. ChromeOS is very aggressive about power savings, and
sets the autosuspend_delay to 100 ms, and disables USB persist.
I attempted to replicate this bug with Ubuntu 12.04, but could not. I
used Ubuntu 12.04 on the same platform, with the same BIOS that the bug
was triggered on ChromeOS with. I also changed the USB sysfs settings
as described above, but still could not reproduce the bug under Ubuntu.
It may be that ChromeOS userspace triggers this bug through additional
settings.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
|
|
If a command on the command ring needs to be cancelled before it is handled
it can be turned to a no-op operation when the ring is stopped.
We want to store the command ring enqueue pointer in the command structure
when the command in enqueued for the cancellation case.
Some commands used to store the command ring dequeue pointers instead of enqueue
(these often worked because enqueue happends to equal dequeue quite often)
Other commands correctly used the enqueue pointer but did not check if it pointed
to a valid trb or a link trb, this caused for example stop endpoint command to timeout in
xhci_stop_device() in about 2% of suspend/resume cases.
This should also solve some weird behavior happening in command cancellation cases.
This patch is based on a patch submitted by Sarah Sharp to linux-usb, but
then forgotten:
http://marc.info/?l=linux-usb&m=136269803207465&w=2
This patch should be backported to kernels as old as 3.7, that contain
the commit b92cc66c047ff7cf587b318fe377061a353c120f "xHCI: add aborting
command ring function"
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
|
|
When a command times out, the command ring is first aborted,
and then stopped. If the command ring is empty when it is stopped
the stop event will point to next command which is not yet set.
xHCI tries to handle this next event often causing an oops.
Don't handle command completion events on stopped cmd ring if ring is
empty.
This patch should be backported to kernels as old as 3.7, that contain
the commit b92cc66c047ff7cf587b318fe377061a353c120f "xHCI: add aborting
command ring function"
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reported-by: Giovanni <giovanni.nervi@yahoo.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
|
|
|
|
MRP doesn't implement the periodictimer in 802.1Q, so it never retries
if packets get lost. I ran into this problem when MRP sent a MVRP
JoinIn before the interface was fully up. The JoinIn was lost, MRP
didn't retry, and MVRP registration failed.
Tested against Juniper QFabric switches
Signed-off-by: Noel Burton-Krahn <noel@burton-krahn.com>
Acked-by: David Ward <david.ward@ll.mit.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Actually re-send packets when the T1 timer runs out. This fixes a bug
where packets are waiting on the write queue until disconnection when
no other traffic is outstanding.
Signed-off-by: Josselin Costanzi <josselin.costanzi@mobile-devices.fr>
Signed-off-by: Maxime Jayat <maxime.jayat@mobile-devices.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch add a method into testptp.c to measure the time offset
between phc and system clock through the ioctl PTP_SYS_OFFSET.
Signed-off-by: Dong Zhu <bluezhudong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add generic rule on encountering Belkin bluetooth usb device F8065bf.
Relevant section from /sys/kernel/debug/usb/devices:
T: Bus=03 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=050d ProdID=065a Rev= 1.12
S: Manufacturer=Broadcom Corp
S: Product=BCM20702A0
S: SerialNumber=0002723E2D29
C:* #Ifs= 4 Cfg#= 1 Atr=a0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
Signed-off-by: Ken O'Brien <kernel@kenobrien.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
There are a mix of function prototypes with and without extern
in the kernel sources. Standardize on not using extern for
function prototypes.
Function prototypes don't need to be written with extern.
extern is assumed by the compiler. Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are a mix of function prototypes with and without extern
in the kernel sources. Standardize on not using extern for
function prototypes.
Function prototypes don't need to be written with extern.
extern is assumed by the compiler. Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are a mix of function prototypes with and without extern
in the kernel sources. Standardize on not using extern for
function prototypes.
Function prototypes don't need to be written with extern.
extern is assumed by the compiler. Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are a mix of function prototypes with and without extern
in the kernel sources. Standardize on not using extern for
function prototypes.
Function prototypes don't need to be written with extern.
extern is assumed by the compiler. Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are a mix of function prototypes with and without extern
in the kernel sources. Standardize on not using extern for
function prototypes.
Function prototypes don't need to be written with extern.
extern is assumed by the compiler. Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are a mix of function prototypes with and without extern
in the kernel sources. Standardize on not using extern for
function prototypes.
Function prototypes don't need to be written with extern.
extern is assumed by the compiler. Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are a mix of function prototypes with and without extern
in the kernel sources. Standardize on not using extern for
function prototypes.
Function prototypes don't need to be written with extern.
extern is assumed by the compiler. Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are a mix of function prototypes with and without extern
in the kernel sources. Standardize on not using extern for
function prototypes.
Function prototypes don't need to be written with extern.
extern is assumed by the compiler. Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are a mix of function prototypes with and without extern
in the kernel sources. Standardize on not using extern for
function prototypes.
Function prototypes don't need to be written with extern.
extern is assumed by the compiler. Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are a mix of function prototypes with and without extern
in the kernel sources. Standardize on not using extern for
function prototypes.
Function prototypes don't need to be written with extern.
extern is assumed by the compiler. Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are a mix of function prototypes with and without extern
in the kernel sources. Standardize on not using extern for
function prototypes.
Function prototypes don't need to be written with extern.
extern is assumed by the compiler. Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are a mix of function prototypes with and without extern
in the kernel sources. Standardize on not using extern for
function prototypes.
Function prototypes don't need to be written with extern.
extern is assumed by the compiler. Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Yuval Mintz says:
====================
This patch contains various bug fixes, half of which are SR-IOV related
(some fixing issues in the recently added VF RSS support), while the other fix
a wide assortments of issues in the driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit b9871bcf "bnx2x: VF RSS support - PF side" has deprecated one of
the previous existing messages. If an old VF driver were to send this message
to the PF then the PF will not reply and leave the mailbox in an unsteady
state (and cause a timeout on the VF side).
Wait until firmware ack is written before unlocking channel
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During flows which mask block attentions (e.g., register dump) all parities
are masked. However, unlike other blocks the MCP's attention is not masked
inside the block but rather the indication to the driver. If another attention
(e.g., link change) will occour while there's an MCP parity, the driver will
ignore the fact that the parity is masked and erroneously report a parity.
This patch forces the driver to read the MCP masking while checking for
parities.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During error flows while loading cnic the return value was incorrectly replaced
by that of bnx2x_set_real_num_queues(); If that function was to finish
successfully then the cnic would have mistakenly thought the load ended
successfully, causing issues (& panics) later on.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bnx2x_iov_static_resc() should be called after IGU was read for information on
the number of available VFs, so that resources will be correctly set.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Due to incorrect usage of PF macros when reading information relating to
interrupts, some PFs were erroneously unable to support VFs.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
