| Age | Commit message (Collapse) | Author |
|---|
|
* pci/host-imx6:
PCI: imx6: Put LTSSM in "Detect" state before disabling it
MAINTAINERS: Add Lucas Stach as co-maintainer for i.MX6 PCI driver
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into fixes
This patch fixes setup of second EDMA channel controller
on DA850.
* tag 'davinci-fixes-for-v3.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: edma: Fix configuration parsing for SoCs with multiple eDMA3 CC
|
|
DRA7 evm REV G and later boards uses a vtt regulator for DDR3
termination and this is controlled by gpio7_11. This gpio is
configured in boot loader. gpio7_11, which is only available only on
Pad A22, in previous boards, is connected only to an unused pad on
expansion connector EXP_P3 and is safe to be muxed as GPIO on all
DRA7-evm versions (without a need to spin off another dts file).
Since gpio7_11 is used to control VTT and should not be reset or kept
in idle state during boot up else VTT will be disconnected and DDR
gets corrupted. So, as part of this change, mark gpio7 as no-reset and
no-idle on init.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
While auditing the various pin ctrl configurations using the following
command:
grep PIN_ arch/arm/boot/dts/dra7-evm.dts|(while read line;
do
v=`echo "$line" | sed -e "s/\s\s*/|/g" | cut -d '|' -f1 |
cut -d 'x' -f2|tr [a-z] [A-Z]`;
HEX=`echo "obase=16;ibase=16;4A003400+$v"| bc`;
echo "$HEX ===> $line";
done)
against DRA75x/74x NDA TRM revision S(SPRUHI2S August 2014),
documentation errors were found for spi1 pinctrl. Fix the same.
Fixes: 6e58b8f1daaf1af ("ARM: dts: DRA7: Add the dts files for dra7 SoC and dra7-evm board")
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Both QSPI and GPMC-NAND share the same Pin (A8) from the SoC for Chip Select
functionality. So both can't be enabled simultaneously.
Disable QSPI node to prevent the pin conflict as well as
be similar to 3.12 release.
CC: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
For NAND read & write wait pin monitoring must be kept disabled as the
wait pin is only used to indicate NAND device ready status and not to
extend each read/write cycle.
So don't print a warning if wait pin is specified while read/write
monitoring is not in the device tree.
Sanity check wait pin number irrespective if read/write monitoring is
set or not.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
NAND uses wait pin only to indicate device readiness after
a block/page operation. It is not use to extend individual
read/write cycle and so read/write wait pin monitoring must
be disabled for NAND.
Add gpmc wait pin information as the NAND uses wait pin 0
for device ready indication.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
NAND uses wait pin only to indicate device readiness after
a block/page operation. It is not use to extend individual
read/write cycle and so read/write wait pin monitoring must
be disabled for NAND.
This patch also gets rid of the below warning when NAND is
accessed for the first time.
omap_l3_noc 44000000.ocp: L3 application error: target 13 mod:1 (unclearable)
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
am437x-gp-evm uses a NAND chip with page size 4096 bytes
and spare area of 225 bytes per page.
For such a setup it is preferrable to use BCH16 ECC scheme over
BCH8. This also makes it compatible with ROM code ECC scheme so
we can boot with NAND after flashing from kernel.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
am43x-epos-evm uses a NAND chip with page size 4096 bytes
and spare area of 225 bytes per page.
For such a setup it is preferrable to use BCH16 ECC scheme over
BCH8. This also makes it compatible with ROM code ECC scheme so
we can boot with NAND after flashing from kernel.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Currently udf_iget() (triggered by NFS) can race with udf_new_inode()
leading to two inode structures with the same inode number:
nfsd: iget_locked() creates inode
nfsd: try to read from disk, block on that.
udf_new_inode(): allocate inode with that inumber
udf_new_inode(): insert it into icache, set it up and dirty
udf_write_inode(): write inode into buffer cache
nfsd: get CPU again, look into buffer cache, see nice and sane on-disk
inode, set the in-core inode from it
Fix the problem by putting inode into icache in locked state (I_NEW set)
and unlocking it only after it's fully set up.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
boilerplate code in udf_{create,mknod,symlink} taken to new helper
symlink case converted to unique id calculated by udf_new_inode() - no
point finding a new one.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Currently UDF doesn't initialize i_generation in any way and thus NFS
can easily get reallocated inodes from stale file handles. Luckily UDF
already has a unique object identifier associated with each inode -
i_unique. Use that for initialization of i_generation.
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
NFS can easily ask for inodes that are already deleted. Currently UDF
happily returns such inodes which is a bug. Return -ESTALE if
udf_read_inode() is asked to read deleted inode.
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Currently __udf_read_inode() wasn't returning anything and we found out
whether we succeeded reading inode by checking whether inode is bad or
not. udf_iget() returned NULL on failure and inode pointer otherwise.
Make these two functions properly propagate errors up the call stack and
use the return value in callers.
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
in spi interrupt handler, we need check RX_IO_DMA status to ensure
rx fifo have received the specify count data.
if not set, the while statement in spi isr function will keep loop,
at last, make the kernel hang.
[The code is actually there in the interrupt handler but apparently it
needs the interrupt unmasking so the handler sees the status -- broonie]
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
|
|
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner. While we are at it also remove the
regcache_cache_only() calls from suspend/resume as there shouldn't be any IO
between suspend and resume.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_OFF at the end of CODEC probe()
can also be removed as the CODEC is already in OFF state at this point.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner. While we are at it also remove the
regcache_cache_only() calls from suspend/resume as there shouldn't be any IO
between suspend and resume.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The ASoC core now takes care of setting the bias level to SND_SOC_BIAS_OFF
when removing the CODEC, no need to do it manually anymore.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We do a bit more than just running the callbacks during suspend and resume
these days (e.g. call regcache_mark_dirty() during suspend). But this is
only when suspend and resume callbacks are specified for the driver,
otherwise nothing is done. This means that drivers which don't want to do
anything special during suspend and resume, but still want the standard
operations to run, need to provide empty suspend and resume callback
functions (rather than no callbacks). This patch updates the suspend and
resume code to always run standard sequence regardless of whether suspend
and resume handlers are provided.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
There is a substantial amount of drivers that in go to SND_SOC_BIAS_OFF on
suspend and go back to SND_SOC_BIAS_SUSPEND on resume (Often this is even
the only thing done in the suspend and resume handlers). This patch
introduces a new suspend_bias_off flag, which when set by a driver will let
the ASoC core automatically put the device's DAPM context at the
SND_SOC_BIAS_OFF level during suspend. Once the device is resumed the DAPM
context will go back to SND_SOC_BIAS_STANDBY (if the context is idle,
otherwise to SND_SOC_BIAS_ON).
This will allow us to remove a fair bit of duplicated code from the drivers.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Currently when a ASoC sound card is unregistered we leave the individual
components in their current state, just call the remove() callback and leave
it to the drivers to do the proper shutdown/cleanup.
This patch introduces a call to snd_soc_dapm_shutdown() when removing the
card. This will make sure that all DAPM widgets are properly powered down
and all DAPM contexts are put at the SND_SOC_BIAS_OFF level. This will
ensure that all components are properly powered down when the card is
removed.
Since a lot of drivers manually go to SND_SOC_BIAS_OFF in their remove
callback this will also allow us to remove a bit of duplicated code.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Set card->instantiated to false when the card is removed to make sure that
operations that expect the card to be fully instantiated do not run anymore
during card removal.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into asoc-suspend
|
|
This reverts commit 150b8be3cda54412ad7b54f5392b513b25c0aaa7.
The I2C core's per-adapter locks can't protect from IRQs, so the driver still
needs a spinlock to protect the register accesses.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: stable@vger.kernel.org # 3.16+
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg <johannes@sipsolutions.net> says:
"Here are a few fixes for mac80211. One has been discussed for a while
and adds a terminating NUL-byte to the alpha2 sent to userspace, which
shouldn't be necessary but since many places treat it as a string we
couldn't move to just sending two bytes.
In addition to that, we have two VLAN fixes from Felix, a mesh fix, a
fix for the recently introduced RX aggregation offload, a revert for
a broken patch (that luckily didn't really cause any harm) and a small
fix for alignment in debugfs."
Signed-off-by: John W. Linville <linville@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon bugfix from Guenter Roeck:
"Fix a bug in the ds1621 driver"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (ds1621) Update zbits after conversion rate change
|
|
git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x86 platform drivers fixes from Darren Hart:
"This is my first pull request since taking on maintenance for the
platform-drivers-x86 tree from Matthew Garrett. These have passed my
build testing and been run through Fengguang's LKP tests. Due to
timing this round, these have not spent any time in linux-next. I
have asked Stephen to include my for-next branch in linux-next going
forward, once he's back from vacation.
Details from tag:
- toshiba_acpi: re-enable hotkeys and cleanups
- ideapad-laptop: revert touchpad disable, and cleanup static/const
usage
- MAINTAINERS: update platform-drivers-x86 maintainer and tree"
* tag 'platform-drivers-x86-v3.17-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
toshiba_acpi: fix and cleanup toshiba_kbd_bl_mode_store()
platform/x86: toshiba: re-enable acpi hotkeys after suspend to disk
ideapad-laptop: Constify DMI table for real!
Revert "ideapad-laptop: Disable touchpad interface on Yoga models"
MAINTAINERS: Update platform-drivers-x86 maintainer and tree
|
|
When cgroup_kn_lock_live() is called through some kernfs operation and
another thread is calling cgroup_rmdir(), we'll trigger the warning in
cgroup_get().
------------[ cut here ]------------
WARNING: CPU: 1 PID: 1228 at kernel/cgroup.c:1034 cgroup_get+0x89/0xa0()
...
Call Trace:
[<c16ee73d>] dump_stack+0x41/0x52
[<c10468ef>] warn_slowpath_common+0x7f/0xa0
[<c104692d>] warn_slowpath_null+0x1d/0x20
[<c10bb999>] cgroup_get+0x89/0xa0
[<c10bbe58>] cgroup_kn_lock_live+0x28/0x70
[<c10be3c1>] __cgroup_procs_write.isra.26+0x51/0x230
[<c10be5b2>] cgroup_tasks_write+0x12/0x20
[<c10bb7b0>] cgroup_file_write+0x40/0x130
[<c11aee71>] kernfs_fop_write+0xd1/0x160
[<c1148e58>] vfs_write+0x98/0x1e0
[<c114934d>] SyS_write+0x4d/0xa0
[<c16f656b>] sysenter_do_call+0x12/0x12
---[ end trace 6f2e0c38c2108a74 ]---
Fix this by calling css_tryget() instead of cgroup_get().
v2:
- move cgroup_tryget() right below cgroup_get() definition. (Tejun)
Cc: <stable@vger.kernel.org> # 3.15+
Reported-by: Toralf Förster <toralf.foerster@gmx.de>
Signed-off-by: Zefan Li <lizefan@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Run these two scripts concurrently:
for ((; ;))
{
mkdir /cgroup/sub
rmdir /cgroup/sub
}
for ((; ;))
{
echo $$ > /cgroup/sub/cgroup.procs
echo $$ > /cgroup/cgroup.procs
}
A kernel bug will be triggered:
BUG: unable to handle kernel NULL pointer dereference at 00000038
IP: [<c10bbd69>] cgroup_put+0x9/0x80
...
Call Trace:
[<c10bbe19>] cgroup_kn_unlock+0x39/0x50
[<c10bbe91>] cgroup_kn_lock_live+0x61/0x70
[<c10be3c1>] __cgroup_procs_write.isra.26+0x51/0x230
[<c10be5b2>] cgroup_tasks_write+0x12/0x20
[<c10bb7b0>] cgroup_file_write+0x40/0x130
[<c11aee71>] kernfs_fop_write+0xd1/0x160
[<c1148e58>] vfs_write+0x98/0x1e0
[<c114934d>] SyS_write+0x4d/0xa0
[<c16f656b>] sysenter_do_call+0x12/0x12
We clear cgrp->kn->priv in the end of cgroup_rmdir(), but another
concurrent thread can access kn->priv after the clearing.
We should move the clearing to css_release_work_fn(). At that time
no one is holding reference to the cgroup and no one can gain a new
reference to access it.
v2:
- move RCU_INIT_POINTER() into the else block. (Tejun)
- remove the cgroup_parent() check. (Tejun)
- update the comment in css_tryget_online_from_dir().
Cc: <stable@vger.kernel.org> # 3.15+
Reported-by: Toralf Förster <toralf.foerster@gmx.de>
Signed-off-by: Zefan Li <lizefan@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This time it contains a bunch of small ASoC fixes that slipped from in
previous updates, in addition to the usual HD-audio fixes and the
regression fixes for FireWire updates in 3.17.
All commits are reasonably small fixes"
* tag 'sound-3.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Fix COEF setups for ALC1150 codec
ASoC: simple-card: Fix bug of wrong decrement DT node's refcount
ALSA: hda - Fix digital mic on Acer Aspire 3830TG
ASoC: omap-twl4030: Fix typo in 2nd dai link's platform_name
ALSA: firewire-lib/dice: add arrangements of PCM pointer and interrupts for Dice quirk
ALSA: dice: fix wrong channel mappping at higher sampling rate
ASoC: cs4265: Fix setting of functional mode and clock divider
ASoC: cs4265: Fix clock rates in clock map table
ASoC: rt5677: correct mismatch widget name
ASoC: rt5640: Do not allow regmap to use bulk read-write operations
ASoC: tegra: Fix typo in include guard
ASoC: da732x: Fix typo in include guard
ASoC: core: fix .info for SND_SOC_BYTES_TLV
ASoC: rcar: Use && instead of & for boolean expressions
ASoC: Use dev_set_name() instead of init_name
ASoC: axi: Fix ADI AXI SPDIF specification
|
|
add the following IDs
USB_PID_PCTV_78E (0x025a) for PCTV 78e
USB_PID_PCTV_79E (0x0262) for PCTV 79e
For these it9135 devices.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Cc: Antti Palosaari <crope@iki.fi>
Cc: <stable@vger.kernel.org> # v3.14+
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
IT9135 RF tuner clock is coming from demodulator. We need enable it
early in demod init, before any tuner I/O. Currently it is enabled
by tuner driver itself, but it is too late and performance will be
reduced as some registers are not updated correctly. Clock is
disabled automatically when demod is put onto sleep.
Cc: <stable@vger.kernel.org> # v3.15+
Cc: Bimow Chen <Bimow.Chen@ite.com.tw>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
That register is needed to program very first in order to operate
correctly.
[crope@iki.fi: returned sequence back, removed sleep, moved reg
write earlier to prevent populating tuner ops in case of failure]
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Bimow Chen <Bimow.Chen@ite.com.tw>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Update IT9135 BX tuner config 60 and 61 inittabs.
[crope@iki.fi: removed two reg writes from driver init itself]
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Bimow Chen <Bimow.Chen@ite.com.tw>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
We should not select SPI bus when sub-driver auto-select is
selected. That option is meant for auto-selecting all possible
ancillary drivers used for selected board driver. Ancillary
drivers should define needed dependencies itself.
I2C and I2C_MUX are still selected here for a reason described on
commit 347f7a3763601d7b466898d1f10080b7083ac4a3
Reverts commit e4462ffc1602d9df21c00a0381dca9080474e27a
Reported-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v3.17-rc4
These updates add back some PIDs that were lost in a recent revert and add a
couple of new ones. Included is also an update to how the sierra driver binds
its interfaces in order to avoid binding CDC interfaces.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
This fixes a boot hang observed when the bootloader already enabled the
PCIe link for its own use. The fundamental problem is that Freescale
forgot to wire up the core reset, so software doesn't have a sane way to
get the core into a defined state.
According to the DW PCIe core reference manual, configuration of the core
may only happen when the LTSSM is disabled, so this is one of the first
things we need to do. Apparently this isn't safe to do when the LTSSM is in
any state other than "detect" as we observe an instant machine hang when
trying to do so while the link is already up.
As a workaround, force LTSSM into detect state right before hitting the
disable switch. There is still a race window because the LTSSM may
transition out of "detect" before we can disable it, but it's the best
we can do for now.
[bhelgaas: mention race window]
Link: http://lkml.kernel.org/r/1406830565-23450-3-git-send-email-l.stach@pengutronix.de
Reported-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
|
|
Also drop Shawn Guo per his request.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Acked-by: Richard Zhu <r65037@freescale.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
|
|
If a gref could not be added (perhaps because the limit has been
reached or there are no more grant references available), the undo
path may crash because __del_gref() frees the gref while it is being
used for a list iteration.
A comment suggests that using list_for_each_entry() is safe since the
gref isn't removed from the list being iterated over, but it is freed
and thus list_for_each_entry_safe() must be used.
Also, explicitly delete the gref from the local per-file list, even
though this is not strictly necessary.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
|
|
Only set gref->gref_id if foreign access was successfully granted and
the grant ref is valid.
If gref->gref_id == -ENOSPC the test in __del_gref() would incorrectly
attempt to end foreign access (because grant_ref_t is unsigned).
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reported-by: Dave Scott <dave.scott@citrix.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
|
|
We did not implement any bound on number of indirect ICBs we follow when
loading inode. Thus corrupted medium could cause kernel to go into an
infinite loop, possibly causing a stack overflow.
Fix the possible stack overflow by removing recursion from
__udf_read_inode() and limit number of indirect ICBs we follow to avoid
infinite loops.
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
In case of capture we should not use rotation. The reverse and mask is
enough to get the data align correctly from the bus to MCU:
Format data from bus after reverse (XRBUF)
S16_LE: |LSB|MSB|xxx|xxx| |xxx|xxx|MSB|LSB|
S24_3LE: |LSB|DAT|MSB|xxx| |xxx|MSB|DAT|LSB|
S24_LE: |LSB|DAT|MSB|xxx| |xxx|MSB|DAT|LSB|
S32_LE: |LSB|DAT|DAT|MSB| |MSB|DAT|DAT|LSB|
With this patch all supported formats will work for playback and capture.
Reported-by: Jyri Sarha <jsarha@ti.com> (broken S24_3LE capture)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
|
|
There's no good reason to separate these since udf_fill_inode() is
called only from __udf_read_inode() and both do part of the same thing.
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
S24_LE is the same on the bus as S24_3LE, which means the codec can support
it.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If we are writing back inode of unlinked directory, its link count ends
up being (u16)-1. Although the inode is deleted, udf_iget() can load the
inode when NFS uses stale file handle and get confused.
Signed-off-by: Jan Kara <jack@suse.cz>
|
