| Age | Commit message (Collapse) | Author |
|---|
|
This patch removes the skb manipulations when nested attributes are added by
using standard helpers.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch advertise the MC_FORWARDING status for IPv4 and IPv6.
This field is readonly, only multicast engine in the kernel updates it.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
* Remove limitation in the maximum number of supported sets in ipset.
Now ipset automagically increments the number of slots in the array
of sets by 64 new spare slots, from Jozsef Kadlecsik.
* Partially remove the generic queue infrastructure now that ip_queue
is gone. Its only client is nfnetlink_queue now, from Florian
Westphal.
* Add missing attribute policy checkings in ctnetlink, from Florian
Westphal.
* Automagically kill conntrack entries that use the wrong output
interface for the masquerading case in case of routing changes,
from Jozsef Kadlecsik.
* Two patches two improve ct object traceability. Now ct objects are
always placed in any of the existing lists. This allows us to dump
the content of unconfirmed and dying conntracks via ctnetlink as
a way to provide more instrumentation in case you suspect leaks,
from myself.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add qlcnic prefix to qlcnic driver module parameters.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Refactor 82xx driver to support new adapter
Update routines to support variable number of NIC partitions
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cleanup get board information API.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Refactor 82xx driver to support new adapter
Update PCI and hardware access routines
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move HW specific data to a seperate structure as part of
refactoring 82xx adapter driver.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add 82xx adapter ID check before 82xx specific operations as part of
refactoring the driver to enable support for new adapter.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
timestamps
This patch implements the hardware timestamping as described in
Documentation/networking/timestamping.txt
Update version to 3.128.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch implements the SIOCSHWTSTAMP ioctl as described in
Documentation/networking/timestamping.txt
[Removed HWTSTAMP_FILTER_ALL handling by returning -ERANGE based on input
from Richard Cochran.]
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the ptp_caps structure, ptp api implementation,
reference clock read and register/unregister functions. All the basic
clock operations as described in Documentation/ptp/ptp.txt are
supported.
Frequency adjustment is performed using hardware with a 24 bit
accumulator and a programmable correction value. On each clk, the
correction value gets added to the accumulator and when it overflows,
the time counter is incremented/decremented and the accumulator reset.
So conversion from ppb to correction value is
ppb * (1 << 24) / 1000000000
[Re-organized to put the ptp_clock_info struct declaration in one patch,
added ptp_clock_info.name, and added locking to tg3_ptp_adjtime() based
on input from Richard Cochran.]
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds code to write the reference clock. If a chip reset is
performed, the hwclock is reinitialized with the adjusted kernel time
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Every caller holds tp->lock when calling tg3_netif_start() except
tg3_io_resume(). Fix it so that it is all consistent. The subsequent
PTP patches add tg3_ptp_resume() to tg3_netif_start() and the tp->lock
is required.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module fixes from Rusty Russell:
"Module signing build fixes for blackfin and metag"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
modsign: add symbol prefix to certificate list
linux/kernel.h: define SYMBOL_PREFIX
|
|
Pull UBI changes from Artem Bityutskiy:
"Fixes for 2 brown-paperbag bugs introduced this merge window by the
fastmap code:
1. The UBI background thread got stuck when a bit-flip happened
because free LEBs was not removed from the "free" tree when we
started using it.
2. I/O debugging checks did not work because we called a sleeping
function in atomic context."
* tag 'upstream-3.7-rc9' of git://git.infradead.org/linux-ubi:
UBI: dont call ubi_self_check_all_ff() in __wl_get_peb()
UBI: remove PEB from free tree in get_peb_for_wl()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull workqueue fixes from Tejun Heo:
"So, safe fixes my ass.
Commit 8852aac25e79 ("workqueue: mod_delayed_work_on() shouldn't queue
timer on 0 delay") had the side-effect of performing delayed_work
sanity checks even when @delay is 0, which should be fine for any sane
use cases.
Unfortunately, megaraid was being overly ingenious. It seemingly
wanted to use cancel_delayed_work_sync() before cancel_work_sync() was
introduced, but didn't want to waste the space for full delayed_work
as it was only going to use 0 @delay. So, it only allocated space for
struct work_struct and then cast it to struct delayed_work and passed
it into delayed_work functions - truly awesome engineering tradeoff to
save some bytes.
Xiaotian fixed it by making megraid allocate full delayed_work for
now. It should be converted to use work_struct and cancel_work_sync()
but I think we better do that after 3.7.
I added another commit to change BUG_ON()s in __queue_delayed_work()
to WARN_ON_ONCE()s so that the kernel doesn't crash even if there are
more such abuses."
* 'for-3.7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: convert BUG_ON()s in __queue_delayed_work() to WARN_ON_ONCE()s
megaraid: fix BUG_ON() from incorrect use of delayed work
|
|
By using the native syscall entry point the kernel was also expecting
64-bit iovec structures.
This is broken since ddd9e91b71072b8ebe89311c3a44b077defa1756 [preadv/
pwritev: MIPS: Add preadv(2) and pwritev(2) syscalls.] which originally
added these two syscalls. I walked through piles of code, including
libc and couldn't find anything that would have worked around the issue
so this change the API to what it should always have been.
Noticed and patch suggested by Al Viro.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Pull sparc fixes from David Miller:
"Two small fixes for Sparc, nobody uses sparc, so these are low risk :-)
1) Piggyback is too picky about the symbol types that _start and _end
have in the final kernel image, and it thus breaks with newer
binutils. Future proof by getting rid of the symbol type checks.
2) exit_group() should kill register windows on sparc64 the same way
we do for plain exit(). Thanks to Al Viro for spotting this."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: Fix piggyback with newer binutils.
sparc64: exit_group should kill register windows just like plain exit.
|
|
The block device access simplification that avoided accessing the (racy)
block size information (commit bbec0270bdd8: "blkdev_max_block: make
private to fs/buffer.c") no longer checks the maximum block size in the
block mapping path.
That was _almost_ as simple as just removing the code entirely, because
the readers and writers all check the size of the device anyway, so
under normal circumstances it "just worked".
However, the block size may be such that the end of the device may
straddle one single buffer_head. At which point we may still want to
access the end of the device, but the buffer we use to access it
partially extends past the end.
The 'bd_set_size()' function intentionally sets the block size to avoid
this, but mounting the device - or setting the block size by hand to
some other value - can modify that block size.
So instead, teach 'submit_bh()' about the special case of the buffer
head straddling the end of the device, and turning such an access into a
smaller IO access, avoiding the problem.
This, btw, also means that unlike before, we can now access the whole
device regardless of device block size setting. So now, even if the
device size is only 512-byte aligned, we can read and write even the
last sector even when having a much bigger block size for accessing the
rest of the device.
So with this, we could now get rid of the 'bd_set_size()' block size
code entirely - resulting in faster IO for the common case - but that
would be a separate patch.
Reported-and-tested-by: Romain Francoise <romain@orebokech.com>
Reporeted-and-tested-by: Meelis Roos <mroos@linux.ee>
Reported-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
|
|
8852aac25e ("workqueue: mod_delayed_work_on() shouldn't queue timer on
0 delay") unexpectedly uncovered a very nasty abuse of delayed_work in
megaraid - it allocated work_struct, casted it to delayed_work and
then pass that into queue_delayed_work().
Previously, this was okay because 0 @delay short-circuited to
queue_work() before doing anything with delayed_work. 8852aac25e
moved 0 @delay test into __queue_delayed_work() after sanity check on
delayed_work making megaraid trigger BUG_ON().
Although megaraid is already fixed by c1d390d8e6 ("megaraid: fix
BUG_ON() from incorrect use of delayed work"), this patch converts
BUG_ON()s in __queue_delayed_work() to WARN_ON_ONCE()s so that such
abusers, if there are more, trigger warning but don't crash the
machine.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Xiaotian Feng <xtfeng@gmail.com>
|
|
Problem:
1) Huge page mapping of anonymous memory is initially invalid. Will be
faulted in by copy-on-write mechanism.
2) Userspace attempts store at the end of the huge mapping.
3) TLB Refill exception handler fill TLB with a normal (4K sized)
invalid page at the end of the huge mapping virtual address range.
4) Userspace restarted, and re-attempts the store at the end of the
huge mapping.
5) Page from #3 is invalid, we get a fault and go to the hugepage
fault handler. This tries to map a huge page and calls
huge_ptep_set_access_flags() to install the mapping.
6) We just call the generic ptep_set_access_flags() to set up the page
tables, but the flush there assumes a normal (4K sized) page and
only tries to flush the first part of the huge page virtual address
out of the TLB, since the existing entry from step #3 doesn't
conflict, nothing is flushed.
7) We attempt to load the mapping into the TLB, but because it
conflicts with the entry from step #3, we get a Machine Check
exception.
The fix: Flush the entire rage covered by the huge page in
huge_ptep_set_access_flags(), and remove the optimization in
local_flush_tlb_range() so that the flush actually does the correct
thing.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Hillf Danton <dhillf@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/4661/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
(cherry picked from commit dd617f258cc39d36be26afee9912624a2d23112c)
|
|
megaraid use INIT_WORK to declare a hotplug_work, but cast the
hotplug_work from work_struct to delayed_work and
schedule_delayed_work on it. This is very dangerous, as other part of
delayed_work might be kernel memories allocated by others.
With commit 8852aac ("workqueue: mod_delayed_work_on() shouldn't queue
timer on 0 delay"), schedule_delayed_work() will check dwork->timer
before queue_work even when @delay is 0, this causes megaraid code to
hit the BUG_ON() in workqueue code. Change megaraid code to use
delayed work.
Signed-off-by: Xiaotian Feng <dannyfeng@tencent.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Neela Syam Kolli <megaraidlinux@lsi.com>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Cc: linux-scsi@vger.kernel.org
|
|
The recent fix for vga switcheroo race in commit 128960a9 opened yet
another race. At the time the audio driver starts probing, user may
turn off D-GPU off. But at this moment, the audio driver still
doesn't register the vga switcheroo client, thus the switching isn't
notified. Then the hardware gets off out of sudden, resulting in
invalid reads and lots of "spurious response" error messages.
For solving this situation, the following changes have been done in
this patch:
- Move again vga switcheroo registration to the very early stage of
the probing; this also requires to set pci drvdata properly before
registration
- Introduce the completion to synchronize the driver probe at vga
switcheroo callbacks; this assures that the whole probing finished
before executing the callbacks
Reported-by: Daniel J Blueman <daniel@quora.org>
Tested-by: Daniel J Blueman <daniel@quora.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
In 5GHz/802.11a, we are allowed to use short slot times. Doing this
may increases performance by 20% for legacy connections (54 MBit/s).
I can confirm this in my tests (27% more throughput using iperf), and
also have a small positive effect (5% more throughput) for HT rates,
tested on 1 stream.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
As ubi_self_check_all_ff() might sleep we are not allowed
to call it from atomic context.
For now we call it only from ubi_wl_get_peb().
There are some code paths where it would also make sense,
but these paths are currently atomic and only enabled
when fastmap is used.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
If UBI is built without fastmap, get_peb_for_wl() has to
remove the PEB manially from the free tree.
Otherwise the requested PEB lives in two trees.
Reported-by: Zach Sadecki <zsadecki@itwatchdogs.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
fix: do block-buffer initialize for the whole next page to zero.
Signed-off-by: Christian Herzig <christian.herzig@keymile.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
* acpi-general:
ACPI / PNP: Do not crash due to stale pointer use during system resume
ACPI / video: Add "Asus UL30VT" to ACPI video detect blacklist
ACPI: do acpisleep dmi check when CONFIG_ACPI_SLEEP is set
|
|
The revision check fails for the beaglebone; Add new revision ID.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Acked-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Use for_each_pci_dev to simplify the code.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
[Boris: cleanup comments and drop loop brackets]
Signed-off-by: Borislav Petkov <bp@alien8.de>
|
|
Commit 947d299686aa9cc8aecf749d54e8475c6e498956 , "ALSA: snd-usb:
properly initialize the sync endpoint", while correcting the
initialization of the sync endpoint when opening just the data
endpoint, prevents devices that has a sync endpoint, with a channel
number different than that of the data endpoint, from functioning.
Due to a different channel and period bytes count, attempting to
initialize the sync endpoint will fail at the usb host driver.
For example, when using xhci:
cannot submit urb 0, error -90: internal error
With this patch, if a sync endpoint has multiple audioformats, a
matching audioformat is preferred. An audioformat must be found
with at least one channel and support the requested sample rate
and PCM format, otherwise the stream will not be opened.
If the number of channels differ between the selected audioformat
and the requested format, adjust the period bytes count accordingly.
It is safe to perform the calculation on the basis of the channel
count, since the requested PCM audio format and the rate must be
supported by the selected audioformat.
Cc: Jeffrey Barish <jeff_barish@earthlink.net>
Cc: Daniel Mack <zonque@gmail.com>
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The commit [88a8516a: ALSA: usbaudio: implement USB autosuspend] added
the support of autopm for USB MIDI output, but it didn't take the MIDI
input into account.
This patch adds the following for fixing the autopm:
- Manage the URB start at the first MIDI input stream open, instead of
the time of instance creation
- Move autopm code to the common substream_open()
- Make snd_usbmidi_input_start/_stop() more robust and add the running
state check
Reviewd-by: Clemens Ladisch <clemens@ladisch.de>
Tested-by: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add a similar protection against the disconnection race and the
invalid use of usb instance after disconnection, as well as we've done
for the USB audio PCM.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=51201
Reviewd-by: Clemens Ladisch <clemens@ladisch.de>
Tested-by: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Changelog v3:
use drm_file's file object instead of gem object's
- gem object's file represents the shmem storage so
process-unique file object should be used instead.
Changelog v2:
call mutex_lock before drm_vm_open_locked is called.
Changelog v1:
This patch makes it takes a reference to gem object when
specific gem mmap is requested. For this, it sets
dev->driver->gem_vm_ops to vma->vm_ops.
And this patch is based on exynos-drm-next-iommu branch of
git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
|
|
This patch adds userptr feautre for G2D module.
The userptr means user space address allocated by malloc().
And the purpose of this feature is to make G2D's dma able
to access the user space region.
To user this feature, user should flag G2D_BUF_USRPTR to
offset variable of struct drm_exynos_g2d_cmd and fill
struct drm_exynos_g2d_userptr with user space address
and size for it and then should set a pointer to
drm_exynos_g2d_userptr object to data variable of struct
drm_exynos_g2d_cmd. The last bit of offset variable is used
to check if the cmdlist's buffer type is userptr or not.
If userptr, the g2d driver gets user space address and size
and then gets pages through get_user_pages().
(another case is counted as gem handle)
Below is sample codes:
static void set_cmd(struct drm_exynos_g2d_cmd *cmd,
unsigned long offset, unsigned long data)
{
cmd->offset = offset;
cmd->data = data;
}
static int solid_fill_test(int x, int y, unsigned long userptr)
{
struct drm_exynos_g2d_cmd cmd_gem[5];
struct drm_exynos_g2d_userptr g2d_userptr;
unsigned int gem_nr = 0;
...
g2d_userptr.userptr = userptr;
g2d_userptr.size = x * y * 4;
set_cmd(&cmd_gem[gem_nr++], DST_BASE_ADDR_REG |
G2D_BUF_USERPTR,
(unsigned long)&g2d_userptr);
...
}
int main(int argc, char **argv)
{
unsigned long addr;
...
addr = malloc(x * y * 4);
...
solid_fill_test(x, y, addr);
...
}
And next, the pages are mapped with iommu table and the device
address is set to cmdlist so that G2D's dma can access it.
As you may know, the pages from get_user_pages() are pinned.
In other words, they CAN NOT be migrated and also swapped out.
So the dma access would be safe.
But the use of userptr feature has performance overhead so
this patch also has memory pool to the userptr feature.
Please, assume that user sends cmdlist filled with userptr
and size every time to g2d driver, and the get_user_pages
funcion will be called every time.
The memory pool has maximum 64MB size and the userptr that
user had ever sent, is holded in the memory pool.
This meaning is that if the userptr from user is same as one
in the memory pool, device address to the userptr in the memory
pool is set to cmdlist.
And last, the pages from get_user_pages() will be freed once
user calls free() and the dma access is completed. Actually,
get_user_pages() takes 2 reference counts if the user process
has never accessed user region allocated by malloc(). Then, if
the user calls free(), the page reference count becomes 1 and
becomes 0 with put_page() call. And the reverse holds as well.
This means how the pages backed are used by dma and freed.
This patch is based on "drm/exynos: add iommu support for g2d",
https://patchwork.kernel.org/patch/1629481/
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
|
|
The function dma_get_sgtable will allocate a sg table internally so
it is not necessary to allocate a sg table before it. The unnecessary
'sg_alloc_table' call is removed.
Signed-off-by: Prathyush K <prathyush.k@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
|
|
This patch fixes the problem of mapping contigous and non contigous dma buffers.
Currently page struct is calculated from the buf->dma_addr which is not the
physical address. It is replaced by buf->pages which points to the page struct
of the first page of contigous memory chunk. This gives the correct page frame
number for mapping.
Non-contigous dma buffers are described using SG table and SG lists. Each
valid SG List is pointing to a single page or group of pages which are
physically contigous. Current implementation just maps the first page of each
SG List and leave the other pages unmapped, leading to a crash. Given solution
finds the page struct for the faulting page through parsing SG table and map it.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
|
|
With iommu support, non-continuous buffer also is supported so
this patch removes these checking from exynos_drm_gem_get/put_dma_addr
funciton.
This patch is based on the below patch set, "drm/exynos: add
iommu support for -next".
http://www.spinics.net/lists/dri-devel/msg29041.html
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
|
|
Chagelog v2:
removed unnecessary structure, struct g2d_gem_node.
Chagelog v1:
This patch adds iommu support for g2d driver. For this, it
adds subdrv_probe/remove callback to enable or disable
g2d iommu. And with this patch, in case of using g2d iommu,
we can get or put device address to a gem handle from user
through exynos_drm_gem_get/put_dma_addr(). Actually, these
functions take a reference to a gem handle so that the gem
object used by g2d dma is released properly.
And runqueue_node has a pointer to drm_file object of current
process to manage gem handles to owner.
This patch is based on the below patch set, "drm/exynos: add
iommu support for -next".
http://www.spinics.net/lists/dri-devel/msg29041.html
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
|
|
Changelog v2:
move iommu support feature to mixer side.
And below is Prathyush's comment.
According to the new IOMMU framework for exynos sysmmus,
the owner of the sysmmu-tv is mixer (which is the actual
device that does DMA) and not hdmi.
The mmu-master in sysmmu-tv node is set as below in exynos5250.dtsi
sysmmu-tv {
-
mmu-master = <&mixer>;
};
Changelog v1:
The iommu will be enabled when hdmi sub driver is probed and
will be disabled when removed.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
|
|
This saves us a few lines of code.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This saves us a few lines of code.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Commit f393ee2b814e3291c12565000210b3cf10aa5c1d forgot to add the
touch_max property for Wacom Bamboo Fun CTH-461/S, ID 056a:00d2.
This broke the touch functionality for that device. This patch,
(done with help of Ping Cheng), adds the correct value and makes
touch work again.
Signed-off-by: Diego Calleja <diegocg@gmail.com>
Reviewed-by: Ping Cheng <pinglinux@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This adds VID/PID combinations for MadCatz, PDP and PowerA (new).
Removed Pelican 'TSZ' Wired Xbox 360 Controller since it's clashing with Edge
wireless Controller and I failed to confirm the PID.
Signed-off-by: "Guillermo A. Amaral B." <g@maral.me>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Fixed a few minor coding style issues in xpad driver.
Signed-off-by: "Guillermo A. Amaral B." <g@maral.me>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The current rules have the .dtb files build in a different directory
from the .dts files. This patch changes microblaze to use the generic dtb
rule which builds .dtb files in the same directory as the source .dts.
This requires moving parts of arch/microblaze/boot/Makefile into newly
created arch/microblaze/boot/dts/Makefile, and updating
arch/microblaze/Makefile to call the new Makefile. linked_dtb.S is also
moved into boot/dts/ since it's used by rules that were moved.
Cc: Michal Simek <monstr@monstr.eu>
Cc: microblaze-uclinux@itee.uq.edu.au
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
|
|
The current rules have the .dtb files build in a different directory
from the .dts files. This patch changes c6x to use the generic dtb
rule which builds .dtb files in the same directory as the source .dts.
This requires moving parts of arch/c6x/boot/Makefile into newly created
arch/c6x/boot/dts/Makefile, and updating arch/c6x/Makefile to call the
new Makefile. linked_dtb.S is also moved into boot/dts/ since it's used
by rules that were moved.
Acked-by: Mark Salter <msalter@redhat.com>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: linux-c6x-dev@linux-c6x.org
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
|
