summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2020-12-28usb: dwc3: ulpi: Replace CPU-based busyloop with Protocol-based oneSerge Semin
Originally the procedure of the ULPI transaction finish detection has been developed as a simple busy-loop with just decrementing counter and no delays. It's wrong since on different systems the loop will take a different time to complete. So if the system bus and CPU are fast enough to overtake the ULPI bus and the companion PHY reaction, then we'll get to take a false timeout error. Fix this by converting the busy-loop procedure to take the standard bus speed, address value and the registers access mode into account for the busy-loop delay calculation. Here is the way the fix works. It's known that the ULPI bus is clocked with 60MHz signal. In accordance with [1] the ULPI bus protocol is created so to spend 5 and 6 clock periods for immediate register write and read operations respectively, and 6 and 7 clock periods - for the extended register writes and reads. Based on that we can easily pre-calculate the time which will be needed for the controller to perform a requested IO operation. Note we'll still preserve the attempts counter in case if the DWC USB3 controller has got some internals delays. [1] UTMI+ Low Pin Interface (ULPI) Specification, Revision 1.1, October 20, 2004, pp. 30 - 36. Fixes: 88bc9d194ff6 ("usb: dwc3: add ULPI interface support") Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Link: https://lore.kernel.org/r/20201210085008.13264-3-Sergey.Semin@baikalelectronics.ru Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-12-28usb: dwc3: ulpi: Use VStsDone to detect PHY regs access completionSerge Semin
In accordance with [1] the DWC_usb3 core sets the GUSB2PHYACCn.VStsDone bit when the PHY vendor control access is done and clears it when the application initiates a new transaction. The doc doesn't say anything about the GUSB2PHYACCn.VStsBsy flag serving for the same purpose. Moreover we've discovered that the VStsBsy flag can be cleared before the VStsDone bit. So using the former as a signal of the PHY control registers completion might be dangerous. Let's have the VStsDone flag utilized instead then. [1] Synopsys DesignWare Cores SuperSpeed USB 3.0 xHCI Host Controller Databook, 2.70a, December 2013, p.388 Fixes: 88bc9d194ff6 ("usb: dwc3: add ULPI interface support") Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Link: https://lore.kernel.org/r/20201210085008.13264-2-Sergey.Semin@baikalelectronics.ru Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-12-28USB: yurex: fix control-URB timeout handlingJohan Hovold
Make sure to always cancel the control URB in write() so that it can be reused after a timeout or spurious CMD_ACK. Currently any further write requests after a timeout would fail after triggering a WARN() in usb_submit_urb() when attempting to submit the already active URB. Reported-by: syzbot+e87ebe0f7913f71f2ea5@syzkaller.appspotmail.com Fixes: 6bc235a2e24a ("USB: add driver for Meywa-Denki & Kayac YUREX") Cc: stable <stable@vger.kernel.org> # 2.6.37 Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-12-28usb: chipidea: ci_hdrc_imx: add missing put_device() call in ↵Yu Kuai
usbmisc_get_init_data() if of_find_device_by_node() succeed, usbmisc_get_init_data() doesn't have a corresponding put_device(). Thus add put_device() to fix the exception handling for this function implementation. Fixes: ef12da914ed6 ("usb: chipidea: imx: properly check for usbmisc") Signed-off-by: Yu Kuai <yukuai3@huawei.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20201117011430.642589-1-yukuai3@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-12-28usb: gadget: u_ether: Fix MTU size mismatch with RX packet sizeManish Narani
Fix the MTU size issue with RX packet size as the host sends the packet with extra bytes containing ethernet header. This causes failure when user sets the MTU size to the maximum i.e. 15412. In this case the ethernet packet received will be of length 15412 plus the ethernet header length. This patch fixes the issue where there is a check that RX packet length must not be more than max packet length. Fixes: bba787a860fa ("usb: gadget: ether: Allow jumbo frames") Signed-off-by: Manish Narani <manish.narani@xilinx.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/1605597215-122027-1-git-send-email-manish.narani@xilinx.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-12-28USB: gadget: legacy: fix return error code in acm_ms_bind()Yang Yingliang
If usb_otg_descriptor_alloc() failed, it need return ENOMEM. Fixes: 578aa8a2b12c ("usb: gadget: acm_ms: allocate and init otg descriptor by otg capabilities") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20201117092955.4102785-1-yangyingliang@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-12-28usb: gadget: Fix spinlock lockup on usb_function_deactivateSriharsha Allenki
There is a spinlock lockup as part of composite_disconnect when it tries to acquire cdev->lock as part of usb_gadget_deactivate. This is because the usb_gadget_deactivate is called from usb_function_deactivate with the same spinlock held. This would result in the below call stack and leads to stall. rcu: INFO: rcu_preempt detected stalls on CPUs/tasks: rcu: 3-...0: (1 GPs behind) idle=162/1/0x4000000000000000 softirq=10819/10819 fqs=2356 (detected by 2, t=5252 jiffies, g=20129, q=3770) Task dump for CPU 3: task:uvc-gadget_wlhe state:R running task stack: 0 pid: 674 ppid: 636 flags:0x00000202 Call trace: __switch_to+0xc0/0x170 _raw_spin_lock_irqsave+0x84/0xb0 composite_disconnect+0x28/0x78 configfs_composite_disconnect+0x68/0x70 usb_gadget_disconnect+0x10c/0x128 usb_gadget_deactivate+0xd4/0x108 usb_function_deactivate+0x6c/0x80 uvc_function_disconnect+0x20/0x58 uvc_v4l2_release+0x30/0x88 v4l2_release+0xbc/0xf0 __fput+0x7c/0x230 ____fput+0x14/0x20 task_work_run+0x88/0x140 do_notify_resume+0x240/0x6f0 work_pending+0x8/0x200 Fix this by doing an unlock on cdev->lock before the usb_gadget_deactivate call from usb_function_deactivate. The same lockup can happen in the usb_gadget_activate path. Fix that path as well. Reported-by: Peter Chen <peter.chen@nxp.com> Link: https://lore.kernel.org/linux-usb/20201102094936.GA29581@b29397-desktop/ Tested-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Sriharsha Allenki <sallenki@codeaurora.org> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20201202130220.24926-1-sallenki@codeaurora.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-12-28usb: gadget: function: printer: Fix a memory leak for interface descriptorZqiang
When printer driver is loaded, the printer_func_bind function is called, in this function, the interface descriptor be allocated memory, if after that, the error occurred, the interface descriptor memory need to be free. Reviewed-by: Peter Chen <peter.chen@nxp.com> Cc: <stable@vger.kernel.org> Signed-off-by: Zqiang <qiang.zhang@windriver.com> Link: https://lore.kernel.org/r/20201210020148.6691-1-qiang.zhang@windriver.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-12-28usb: dwc3: meson-g12a: disable clk on error handling path in probeZheng Zengkai
dwc3_meson_g12a_probe() does not invoke clk_bulk_disable_unprepare() on one error handling path. This patch fixes that. Fixes: 347052e3bf1b ("usb: dwc3: meson-g12a: fix USB2 PHY initialization on G12A and A1 SoCs") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zheng Zengkai <zhengzengkai@huawei.com> Cc: stable <stable@vger.kernel.org> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Link: https://lore.kernel.org/r/20201215025459.91794-1-zhengzengkai@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-12-28USB: xhci: fix U1/U2 handling for hardware with XHCI_INTEL_HOST quirk setMichael Grzeschik
The commit 0472bf06c6fd ("xhci: Prevent U1/U2 link pm states if exit latency is too long") was constraining the xhci code not to allow U1/U2 sleep states if the latency to wake up from the U-states reached the service interval of an periodic endpoint. This fix was not taking into account that in case the quirk XHCI_INTEL_HOST is set, the wakeup time will be calculated and configured differently. It checks for u1_params.mel/u2_params.mel as a limit. But the code could decide to write another MEL into the hardware. This leads to broken cases where not enough bandwidth is available for other devices: usb 1-2: can't set config #1, error -28 This patch is fixing that case by checking for timeout_ns after the wakeup time was calculated depending on the quirks. Fixes: 0472bf06c6fd ("xhci: Prevent U1/U2 link pm states if exit latency is too long") Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20201215193147.11738-1-m.grzeschik@pengutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-12-28usb: typec: intel_pmc_mux: Configure HPD first for HPD+IRQ requestMadhusudanarao Amara
Warm reboot scenarios some times type C Mux driver gets Mux configuration request as HPD=1,IRQ=1. In that scenario typeC Mux driver need to configure Mux as follows as per IOM requirement: (1). Confgiure Mux HPD = 1, IRQ = 0 (2). Configure Mux with HPD = 1, IRQ = 1 IOM expects TypeC Mux configuration as follows: (1). HPD=1, IRQ=0 (2). HPD=1, IRQ=1 if IOM gets mux config request (2) without configuring (1), it will ignore the request. The impact of this is there is no DP_alt mode display. Fixes: 43d596e32276 ("usb: typec: intel_pmc_mux: Check the port status before connect") Cc: stable@vger.kernel.org Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Madhusudanarao Amara <madhusudanarao.amara@intel.com> Link: https://lore.kernel.org/r/20201216140918.49197-1-madhusudanarao.amara@intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-12-28USB: cdc-wdm: Fix use after free in service_outstanding_interrupt().Tetsuo Handa
syzbot is reporting UAF at usb_submit_urb() [1], for service_outstanding_interrupt() is not checking WDM_DISCONNECTING before calling usb_submit_urb(). Close the race by doing same checks wdm_read() does upon retry. Also, while wdm_read() checks WDM_DISCONNECTING with desc->rlock held, service_interrupt_work() does not hold desc->rlock. Thus, it is possible that usb_submit_urb() is called from service_outstanding_interrupt() from service_interrupt_work() after WDM_DISCONNECTING was set and kill_urbs() from wdm_disconnect() completed. Thus, move kill_urbs() in wdm_disconnect() to after cancel_work_sync() (which makes sure that service_interrupt_work() is no longer running) completed. Although it seems to be safe to dereference desc->intf->dev in service_outstanding_interrupt() even if WDM_DISCONNECTING was already set because desc->rlock or cancel_work_sync() prevents wdm_disconnect() from reaching list_del() before service_outstanding_interrupt() completes, let's not emit error message if WDM_DISCONNECTING is set by wdm_disconnect() while usb_submit_urb() is in progress. [1] https://syzkaller.appspot.com/bug?extid=9e04e2df4a32fb661daf Reported-by: syzbot <syzbot+9e04e2df4a32fb661daf@syzkaller.appspotmail.com> Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/620e2ee0-b9a3-dbda-a25b-a93e0ed03ec5@i-love.sakura.ne.jp Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-12-28usb: gadget: fsl_mxc_udc: Remove the driverFabio Estevam
Since 5.10-rc1 i.MX is a devicetree-only platform, and this driver was only used by the old non-DT i.MX devices. Remove the driver as it has no users left. Signed-off-by: Fabio Estevam <festevam@gmail.com> Acked-by: Peter Chen <peter.chen@nxp.com> Link: https://lore.kernel.org/r/20201210210413.15262-1-festevam@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-12-28dt-bindings: usb: Add new compatible string for AM64 SoCAswath Govindraju
Add compatible string in j721e-usb binding file as the same USB subsystem is present in AM64. Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com> Link: https://lore.kernel.org/r/20201215042549.7956-1-a-govindraju@ti.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-12-28MAINTAINERS: Update address for Cadence USB3 driverRoger Quadros
Updates my email address for Cadence USB3 driver. Signed-off-by: Roger Quadros <rogerq@ti.com> Link: https://lore.kernel.org/r/20201218105736.17667-1-rogerq@ti.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-12-28USB: cdc-acm: blacklist another IR Droid deviceSean Young
This device is supported by the IR Toy driver. Reported-by: Georgi Bakalski <georgi.bakalski@gmail.com> Signed-off-by: Sean Young <sean@mess.org> Acked-by: Oliver Neukum <oneukum@suse.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20201227134502.4548-2-sean@mess.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-12-28Merge tag 'v5.11-rc1' into spi-5.11Mark Brown
Linux 5.11-rc1
2020-12-28Merge tag 'v5.11-rc1' into regulator-5.11Mark Brown
Linux 5.11-rc1
2020-12-28staging: mt7621-dma: Fix a resource leak in an error handling pathChristophe JAILLET
If an error occurs after calling 'mtk_hsdma_init()', it must be undone by a corresponding call to 'mtk_hsdma_uninit()' as already done in the remove function. Fixes: 0853c7a53eb3 ("staging: mt7621-dma: ralink: add rt2880 dma engine") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20201213153513.138723-1-christophe.jaillet@wanadoo.fr Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-12-28Staging: comedi: Return -EFAULT if copy_to_user() failsDan Carpenter
Return -EFAULT on error instead of the number of bytes remaining to be copied. Fixes: bac42fb21259 ("comedi: get rid of compat_alloc_user_space() mess in COMEDI_CMD{,TEST} compat") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/X8c3pfwFy2jpy4BP@mwanda Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-12-28staging: spmi: hisi-spmi-controller: Fix some error handling pathsChristophe JAILLET
IN the probe function, if an error occurs after calling 'spmi_controller_alloc()', it must be undone by a corresponding 'spmi_controller_put() call. In the remove function, use 'spmi_controller_put(ctrl)' instead of 'kfree(ctrl)'. While a it fix an error message (s/spmi_add_controller/spmi_controller_add/) Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Link: https://lore.kernel.org/r/20201213151105.137731-1-christophe.jaillet@wanadoo.fr Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-12-28interconnect: imx8mq: Use icc_sync_stateMartin Kepplinger
Add the icc_sync_state callback to notify the framework when consumers are probed and the bandwidth doesn't have to be kept at maximum anymore. Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm> Suggested-by: Georgi Djakov <georgi.djakov@linaro.org> Fixes: 7d3b0b0d8184 ("interconnect: qcom: Use icc_sync_state") Link: https://lore.kernel.org/r/20201210100906.18205-6-martin.kepplinger@puri.sm Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
2020-12-28interconnect: imx: Remove a useless testChristophe JAILLET
'dn' can't be NULL here, it is tested just the line above. Remove this useless test. Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Link: https://lore.kernel.org/r/20201206121322.29434-1-christophe.jaillet@wanadoo.fr Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
2020-12-28interconnect: imx: Add a missing of_node_put after of_device_is_availableChristophe JAILLET
Add an 'of_node_put()' call when a tested device node is not available. Fixes: f0d8048525d7 ("interconnect: Add imx core driver") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Link: https://lore.kernel.org/r/20201206121304.29381-1-christophe.jaillet@wanadoo.fr Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
2020-12-28interconnect: qcom: fix rpmh link failuresArnd Bergmann
When CONFIG_COMPILE_TEST is set, it is possible to build some of the interconnect drivers into the kernel while their dependencies are loadable modules, which is bad: arm-linux-gnueabi-ld: drivers/interconnect/qcom/bcm-voter.o: in function `qcom_icc_bcm_voter_commit': (.text+0x1f8): undefined reference to `rpmh_invalidate' arm-linux-gnueabi-ld: (.text+0x20c): undefined reference to `rpmh_write_batch' arm-linux-gnueabi-ld: (.text+0x2b0): undefined reference to `rpmh_write_batch' arm-linux-gnueabi-ld: (.text+0x2e8): undefined reference to `rpmh_write_batch' arm-linux-gnueabi-ld: drivers/interconnect/qcom/icc-rpmh.o: in function `qcom_icc_bcm_init': (.text+0x2ac): undefined reference to `cmd_db_read_addr' arm-linux-gnueabi-ld: (.text+0x2c8): undefined reference to `cmd_db_read_aux_data' The exact dependencies are a bit complicated, so split them out into a hidden Kconfig symbol that all drivers can in turn depend on to get it right. Fixes: 976daac4a1c5 ("interconnect: qcom: Consolidate interconnect RPMh support") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20201204165030.3747484-1-arnd@kernel.org Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
2020-12-28fanotify: Fix sys_fanotify_mark() on native x86-32Brian Gerst
Commit 121b32a58a3a ("x86/entry/32: Use IA32-specific wrappers for syscalls taking 64-bit arguments") converted native x86-32 which take 64-bit arguments to use the compat handlers to allow conversion to passing args via pt_regs. sys_fanotify_mark() was however missed, as it has a general compat handler. Add a config option that will use the syscall wrapper that takes the split args for native 32-bit. [ bp: Fix typo in Kconfig help text. ] Fixes: 121b32a58a3a ("x86/entry/32: Use IA32-specific wrappers for syscalls taking 64-bit arguments") Reported-by: Paweł Jasiak <pawel@jasiak.xyz> Signed-off-by: Brian Gerst <brgerst@gmail.com> Signed-off-by: Borislav Petkov <bp@suse.de> Acked-by: Jan Kara <jack@suse.cz> Acked-by: Andy Lutomirski <luto@kernel.org> Link: https://lkml.kernel.org/r/20201130223059.101286-1-brgerst@gmail.com
2020-12-28netfilter: nftables: add set expression flagsPablo Neira Ayuso
The set flag NFT_SET_EXPR provides a hint to the kernel that userspace supports for multiple expressions per set element. In the same direction, NFT_DYNSET_F_EXPR specifies that dynset expression defines multiple expressions per set element. This allows new userspace software with old kernels to bail out with EOPNOTSUPP. This update is similar to ef516e8625dd ("netfilter: nf_tables: reintroduce the NFT_SET_CONCAT flag"). The NFT_SET_EXPR flag needs to be set on when the NFTA_SET_EXPRESSIONS attribute is specified. The NFT_SET_EXPR flag is not set on with NFTA_SET_EXPR to retain backward compatibility in old userspace binaries. Fixes: 48b0ae046ee9 ("netfilter: nftables: netlink support for several set element expressions") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2020-12-28netfilter: nft_dynset: report EOPNOTSUPP on missing set featurePablo Neira Ayuso
If userspace requests a feature which is not available the original set definition, then bail out with EOPNOTSUPP. If userspace sends unsupported dynset flags (new feature not supported by this kernel), then report EOPNOTSUPP to userspace. EINVAL should be only used to report malformed netlink messages from userspace. Fixes: 22fe54d5fefc ("netfilter: nf_tables: add support for dynamic set updates") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2020-12-28habanalabs: fix order of status checkOded Gabbay
When the device is in reset or needs to be reset, the disabled property is don't-care. Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
2020-12-28habanalabs: register to pci shutdown callbackOded Gabbay
We need to make sure our device is idle when rebooting a virtual machine. This is done in the driver level. The firmware will later handle FLR but we want to be extra safe and stop the devices until the FLR is handled. Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
2020-12-28habanalabs: add validation cs counter, fix misplaced countersAlon Mizrahi
Up until now validation errors were counted in the parsing field of the cs_counters struct, so we added a new counter and increased it when needed. In addition, there were some locations where only one of the counters was updated (ctx or aggregate) so add the second one to be updated as well. Signed-off-by: Alon Mizrahi <amizrahi@habana.ai> Reviewed-by: Oded Gabbay <ogabbay@kernel.org> Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
2020-12-28habanalabs/gaudi: retry loading TPC f/w on -EINTROded Gabbay
If loading the firmware file for the TPC f/w was interrupted, try to do it again, up to 5 times. Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
2020-12-28habanalabs: adjust pci controller init to new firmwareOded Gabbay
When the firmware security is enabled, the pcie_aux_dbi_reg_addr register in the PCI controller is blocked. Therefore, ignore the result of writing to this register and assume it worked. Also remove the prints on errors in the internal ELBI write function. If the security is enabled, the firmware is responsible for setting this register correctly so we won't have any problem. If the security is disabled, the write will work (unless something is totally broken at the PCI level and then the whole sequence will fail). In addition, remove a write to register pcie_aux_dbi_reg_addr+4, which was never actually needed. Moreover, PCIE_DBI registers are blocked to access from host when firmware security is enabled. Use a different register to flush the writes. Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
2020-12-28habanalabs: update comment in hl_boot_if.hOded Gabbay
Hard-reset flag is updated in many stages of the boot sequence of the firmware. Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
2020-12-28habanalabs/gaudi: enhance reset messageOded Gabbay
Print the initiator who performs the hard-reset for easier debugging. Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
2020-12-28habanalabs: full FW hard reset supportOfir Bitton
Driver must fetch FW hard reset capability at every FW boot stage: preboot, CPU boot, CPU application. If hard reset is triggered, driver will take into consideration only the last capability received. Signed-off-by: Ofir Bitton <obitton@habana.ai> Reviewed-by: Oded Gabbay <ogabbay@kernel.org> Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
2020-12-28habanalabs/gaudi: disable CGM at HW initializationOded Gabbay
In case the clock gating was enabled in preboot we need to disable it at the H/W initialization stage before touching the MME/TPC registers. Otherwise, the ASIC can get stuck. If the security is enabled in the firmware level, the CGM is always disabled and the driver can't enable it. Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
2020-12-28habanalabs: Revise comment to align with mirror list nameTomer Tayar
hw_queues_mirror was renamed to cs_mirror, so revise accordingly a comment that refers to this list. Signed-off-by: Tomer Tayar <ttayar@habana.ai> Reviewed-by: Oded Gabbay <ogabbay@kernel.org> Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
2020-12-28habanalabs/gaudi: do not set EB in collective slave queuesAlon Mizrahi
We don't need to set EB on signal packets from collective slave queues as it degrades performance. Because the slaves are the network queues, the engine barrier doesn't actually guarantee that the packet has been sent. Signed-off-by: Alon Mizrahi <amizrahi@habana.ai> Reviewed-by: Oded Gabbay <ogabbay@kernel.org> Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
2020-12-28habanalabs: preboot hard reset supportOfir Bitton
FW hard reset capability indication is now moved to preboot stage. Driver will check if HW is dirty only after it validated preboot is up. If HW is dirty, driver will perform a hard reset according to the FW capability. In addition, FW defines a new message which driver need to send in order to initiate a hard reset. Signed-off-by: Ofir Bitton <obitton@habana.ai> Reviewed-by: Oded Gabbay <ogabbay@kernel.org> Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
2020-12-28habanalabs: remove generic gaudi get_pll_freq functionAlon Mizrahi
As we only fetch the CPU_PLL frequency in gaudi, we don't need a generic get_pll_frequency function which takes a pll index as input Signed-off-by: Alon Mizrahi <amizrahi@habana.ai> Reviewed-by: Oded Gabbay <ogabbay@kernel.org> Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
2020-12-28habanalabs: fetch PSOC PLL frequency from F/W in goyaAlon Mizrahi
When the F/W security is enabled, goya needs to fetch the PSOC pll frequency through a dedicated interface Signed-off-by: Alon Mizrahi <amizrahi@habana.ai> Reviewed-by: Oded Gabbay <ogabbay@kernel.org> Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
2020-12-28habanalabs: add comment for pll frequency ioctl opcodeAlon Mizrahi
Forgot to add the comment for the opcode when it was added. Signed-off-by: Alon Mizrahi <amizrahi@habana.ai> Reviewed-by: Oded Gabbay <ogabbay@kernel.org> Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
2020-12-28habanalabs: Fix a missing-braces warningTomer Tayar
Fix a compilation "missing braces around initializer" warning. Signed-off-by: Tomer Tayar <ttayar@habana.ai> Reviewed-by: Oded Gabbay <ogabbay@kernel.org> Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
2020-12-28opp: Call the missing clk_put() on errorViresh Kumar
Fix the clock reference counting by calling the missing clk_put() in the error path. Cc: v5.10 <stable@vger.kernel.org> # v5.10 Fixes: dd461cd9183f ("opp: Allow dev_pm_opp_get_opp_table() to return -EPROBE_DEFER") Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
2020-12-28opp: fix memory leak in _allocate_opp_tableQuanyang Wang
In function _allocate_opp_table, opp_dev is allocated and referenced by opp_table via _add_opp_dev. But in the case that the subsequent calls return -EPROBE_DEFER, it will jump to err label and opp_table will be freed. Then opp_dev becomes an unreferenced object to cause memory leak. So let's call _remove_opp_dev to do the cleanup. This fixes the following kmemleak report: unreferenced object 0xffff000801524a00 (size 128): comm "swapper/0", pid 1, jiffies 4294892465 (age 84.616s) hex dump (first 32 bytes): 40 00 56 01 08 00 ff ff 40 00 56 01 08 00 ff ff @.V.....@.V..... b8 52 77 7f 08 00 ff ff 00 3c 4c 00 08 00 ff ff .Rw......<L..... backtrace: [<00000000b1289fb1>] kmemleak_alloc+0x30/0x40 [<0000000056da48f0>] kmem_cache_alloc+0x3d4/0x588 [<00000000a84b3b0e>] _add_opp_dev+0x2c/0x88 [<0000000062a380cd>] _add_opp_table_indexed+0x124/0x268 [<000000008b4c8f1f>] dev_pm_opp_of_add_table+0x20/0x1d8 [<00000000e5316798>] dev_pm_opp_of_cpumask_add_table+0x48/0xf0 [<00000000db0a8ec2>] dt_cpufreq_probe+0x20c/0x448 [<0000000030a3a26c>] platform_probe+0x68/0xd8 [<00000000c618e78d>] really_probe+0xd0/0x3a0 [<00000000642e856f>] driver_probe_device+0x58/0xb8 [<00000000f10f5307>] device_driver_attach+0x74/0x80 [<0000000004f254b8>] __driver_attach+0x58/0xe0 [<0000000009d5d19e>] bus_for_each_dev+0x70/0xc8 [<0000000000d22e1c>] driver_attach+0x24/0x30 [<0000000001d4e952>] bus_add_driver+0x14c/0x1f0 [<0000000089928aaa>] driver_register+0x64/0x120 Cc: v5.10 <stable@vger.kernel.org> # v5.10 Fixes: dd461cd9183f ("opp: Allow dev_pm_opp_get_opp_table() to return -EPROBE_DEFER") Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com> [ Viresh: Added the stable tag ] Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
2020-12-27Linux 5.11-rc1v5.11-rc1Linus Torvalds
2020-12-27proc mountinfo: make splice available againLinus Torvalds
Since commit 36e2c7421f02 ("fs: don't allow splice read/write without explicit ops") we've required that file operation structures explicitly enable splice support, rather than falling back to the default handlers. Most /proc files use the indirect 'struct proc_ops' to describe their file operations, and were fixed up to support splice earlier in commits 40be821d627c..b24c30c67863, but the mountinfo files interact with the VFS directly using their own 'struct file_operations' and got missed as a result. This adds the necessary support for splice to work for /proc/*/mountinfo and friends. Reported-by: Joan Bruguera Micó <joanbrugueram@gmail.com> Reported-by: Jussi Kivilinna <jussi.kivilinna@iki.fi> Link: https://bugzilla.kernel.org/show_bug.cgi?id=209971 Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-12-27Merge tag 'ntb-5.11' of git://github.com/jonmason/ntbLinus Torvalds
Pull NTB fixes from Jon Mason: "Bug fix for IDT NTB and Intel NTB LTR management support" * tag 'ntb-5.11' of git://github.com/jonmason/ntb: ntb: intel: add Intel NTB LTR vendor support for gen4 NTB ntb: idt: fix error check in ntb_hw_idt.c
2020-12-27Merge branch 'linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6 Pull crypto fixes from Herbert Xu: "Fix a number of autobuild failures due to missing Kconfig dependencies" * 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: crypto: qat - add CRYPTO_AES to Kconfig dependencies crypto: keembay - Add dependency on HAS_IOMEM crypto: keembay - CRYPTO_DEV_KEEMBAY_OCS_AES_SM4 should depend on ARCH_KEEMBAY
generated by cgit (git 2.34.1) at 2025-09-12 16:56:49 +0000