| Age | Commit message (Collapse) | Author |
|---|
|
To make it clear which exceptions can't be taken to EL1 or EL2, add
comments next to the ESR_ELx_EC_* macro definitions.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
The AXP20X_OFF define is an actual specific bit, define it as such.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add the bitops.h header as we need it, alphabetize header order.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The OLinuXino Lime2 has a big capacitor on its LDO3 output. It is
actually too large, causing the PMIC to shutdown when toggling the LDO3.
By enabling soft-start and ramp delay we increase the time for the
capacitor to charge lowering the current drain on the power regulator.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In the past, there have been words on various lists that if LDO3 is
disabled in u-boot, but enabled in the DTS, the axp209 driver would
fail to continue/hang. Several enable/disable patches have been
issues to devicetree's in both the kernel and u-boot to address
this issue.
What really happened however, was that the AXP209 shuts down without
a notice and without setting an interrupt. This is caused when LDO3
gets overloaded, for example with large capacitors on the LDO3 output.
Normally, we would expect that AXP209 would source 200 mA as per
datasheet and set and trigger an interrupt when being overloaded.
For some reason however, this does not happen.
As a work-around, implement software-based 'regulator-soft-start'
property for AXP209 LDO3 regulator, which is used to first bring up
the LDO3 to the lowest possible voltage and then enable the LDO.
After that, we can set the requested voltage as usual.
Combining this setting with the regulator-ramp-delay allows LDO3 to
come up slowly and staggered, potentially reducing overall inrush current.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In the past, there have been words on various lists that if LDO3 is
disabled in u-boot, but enabled in the DTS, the axp209 driver would
fail to continue/hang. Several enable/disable patches have been
issues to devicetree's in both the kernel and u-boot to address
this issue.
What really happened however, was that the AXP209 shuts down without
a notice and without setting an interrupt. This is caused when LDO3
gets overloaded, for example with large capacitors on the LDO3 output.
Normally, we would expect that AXP209 would source 200 mA as per
datasheet and set and trigger an interrupt when being overloaded.
For some reason however, this does not happen.
As a work-around, we use the soft-start constraint of the regulator
node to first bring up the LDO3 to the lowest possible voltage and
then enable the LDO. After that, we can set the requested voltage
as usual.
Combining this setting with the regulator-ramp-delay allows LDO3 to
enable voltage slowly and staggered, potentially reducing overall
inrush current.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The AXP209 supports ramping up voltages on several regulators such as
DCDC2 and LDO3, therefore we can use the standard 'regulator-ramp-delay'
property for those 2 regulators.
Note that the voltage ramp only works when the regulator is already
enabled. E.g. when going from say 0.7 V to 3.6 V.
When turning on the regulator, no voltage ramp is performed in hardware.
What this means, is that if the bootloader brings up the voltage at 0.7 V,
the ramp delay property is properly applied. If however, the bootloader
leaves the power off, no ramp delay is applied when the power is
enabled by the regulator framework.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The AXP209 supports ramping up voltages on several regulators such as
DCDC2 and LDO3.
This patch adds preliminary support for the regulator-ramp-delay property
for these 2 regulators. Note that the voltage ramp only works when
regulator is already enabled. E.g. when going from say 0.7 V to 3.6 V.
When turning on the regulator, no voltage ramp is performed in hardware.
What this means, is that if the bootloader brings up the voltage at 0.7 V,
the ramp delay property is properly applied. If however, the bootloader
leaves the power off, no ramp delay is applied when the power is
enabled by the regulator framework.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The current axp20x names the ramping register 'scal' which probably
means scaling. Since the register really has nothing to do with
scaling, but really is the voltage ramp we rename it appropriately.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator into regulator-4.21
|
|
Even if this spdif input driver is only supposed to be used on 64bits
platform, there is possible problem with 32bits and do_div, as reported
by the kbuild robot. Just fix it.
Fixes: 5ce5658375e6 ("ASoC: meson: add axg spdif input")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add error logs to make probe debug easier.
Also remove hard-coded dependency on NHLT. NHLT literally stands for
NonHdaudioLinkTable and is only required for SSP/DMIC interfaces.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
bus->ppcap is now tested upfront, there is no need to re-check if the
hardware is exposed as needed. Remove tests and remove indentation.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Check immediately if required HDaudio capabilities can't be found (no
PPCAP or no streams exposed in GCAP), and move all DMA inits after the
error tests.
PPCAP and GCAP are not reliable indicators of DSP presence, but if
they don't exist then the driver will not work.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The existing PPCAP and GCAP fields cannot be used reliably to
determine if the DSP is enabled by the BIOS. Instead rely on the
class/subclass information to find out if this driver can run or
not. The values in the code don't seem to be documented in publicly
available documents but are part of recommendations made to BIOS
writers and have been verified to be accurate on a number of
platforms.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
It's with CNP, supposed to be equivalent with CNL entry.
Keep the existing declaration style for now, at a later point we may
transition and use PCI_DEVICE_DATA().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Although the upper 32 bits of the PMEVTYPER<n>_EL0 registers are RES0,
we should treat the EXCLUDE_EL* bit definitions as unsigned so that we
avoid accidentally sign-extending the privilege filtering bit (bit 31)
into the upper half of the register.
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Enable DAC/ADC only when playing/capturing
Signed-off-by: Kirill Marinushkin <kmarinushkin@birdec.tech>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Enabled i2s driver build option.
Signed-off-by: Maruthi Srinivas Bayyavarapu <maruthi.srinivas.bayyavarapu@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
I2S IP instance can work in transmitter/playback or receiver/capture mode
exclusively. The patch registers corresponding instance as ASoC component
with audio framework.
Signed-off-by: Maruthi Srinivas Bayyavarapu <maruthi.srinivas.bayyavarapu@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Added documentation for I2S IP core DT bindings.
Signed-off-by: Maruthi Srinivas Bayyavarapu <maruthi.srinivas.bayyavarapu@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The new Dell IoT platform uses kabylake + alc3277 codec, and alc3277
shares the driver with the codec rt5660, here we generate a new
machine driver based on kbl_da7219_max98357a.
The audio design on this IoT platform is as below:
- Intel kabylake platform
- connect the codec ALC3277 via SSP0
- line-out and line-in with Micbias jacks
- line-out mute control and jack detection of line-out and line-in
- two HDMI ports with audio capability
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into asoc-4.21 intel dep
|
|
Add entry for mt76 driver in MAINTAINERS file
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Starting from mac80211 commit adf8ed01e4fd ("mac80211: add an optional
TXQ for other PS-buffered frames") and commit 0eeb2b674f05 ("mac80211:
add an option for station management TXQ") a new per-sta queue has been
introduced for bufferable management frames.
sta->txq[IEEE80211_NUM_TIDS] is initialized just if the driver reports
the following hw flags:
- IEEE80211_HW_STA_MMPDU_TXQ
- IEEE80211_HW_BUFF_MMPDU_TXQ
This can produce a NULL pointer dereference in mt76_stop_tx_queues
since mt76 iterates on all available sta tx queues assuming they are
initialized by mac80211. This issue has been spotted analyzing the code
(it has not triggered any crash yet)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
While the CSV3 field of the ID_AA64_PFR0 CPU ID register can be checked
to see if a CPU is susceptible to Meltdown and therefore requires kpti
to be enabled, existing CPUs do not implement this field.
We therefore whitelist all unaffected Cortex-A CPUs that do not implement
the CSV3 field.
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
This reverts commit 5188d5453bc9380ccd4ae1086138dd485d13aef2, because it
introduced lock recursion:
BUG: spinlock recursion on CPU#2, kworker/u13:1/395
lock: 0xffffffc0e28a47f0, .magic: dead4ead, .owner: kworker/u13:1/395, .owner_cpu: 2
CPU: 2 PID: 395 Comm: kworker/u13:1 Not tainted 4.20.0-rc4+ #2
Hardware name: Google Kevin (DT)
Workqueue: MWIFIEX_RX_WORK_QUEUE mwifiex_rx_work_queue [mwifiex]
Call trace:
dump_backtrace+0x0/0x140
show_stack+0x20/0x28
dump_stack+0x84/0xa4
spin_bug+0x98/0xa4
do_raw_spin_lock+0x5c/0xdc
_raw_spin_lock_irqsave+0x38/0x48
mwifiex_flush_data+0x2c/0xa4 [mwifiex]
call_timer_fn+0xcc/0x1c4
run_timer_softirq+0x264/0x4f0
__do_softirq+0x1a8/0x35c
do_softirq+0x54/0x64
netif_rx_ni+0xe8/0x120
mwifiex_recv_packet+0xfc/0x10c [mwifiex]
mwifiex_process_rx_packet+0x1d4/0x238 [mwifiex]
mwifiex_11n_dispatch_pkt+0x190/0x1ac [mwifiex]
mwifiex_11n_rx_reorder_pkt+0x28c/0x354 [mwifiex]
mwifiex_process_sta_rx_packet+0x204/0x26c [mwifiex]
mwifiex_handle_rx_packet+0x15c/0x16c [mwifiex]
mwifiex_rx_work_queue+0x104/0x134 [mwifiex]
worker_thread+0x4cc/0x72c
kthread+0x134/0x13c
ret_from_fork+0x10/0x18
This was clearly not tested well at all. I simply performed 'wget' in a
loop and it fell over within a few seconds.
Fixes: 5188d5453bc9 ("mwifiex: restructure rx_reorder_tbl_lock usage")
Cc: <stable@vger.kernel.org>
Cc: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
With commit 0a9f8f0a1ba9 ("rtlwifi: fix btmpinfo timeout while processing
C2H_BT_INFO"), calling rtl_c2hcmd_enqueue() with rtl_c2h_fast_cmd() true,
the routine returns without freeing that skb, thereby leaking it.
This issue has been discussed at https://github.com/lwfinger/rtlwifi_new/issues/401
and the fix tested there.
Fixes: 0a9f8f0a1ba9 ("rtlwifi: fix btmpinfo timeout while processing C2H_BT_INFO")
Reported-and-tested-by: Francisco Machado Magalhães Neto <franmagneto@gmail.com>
Cc: Francisco Machado Magalhães Neto <franmagneto@gmail.com>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Stable <stable@vger.kernel.org> # 4.18+
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This patch adds a regulator driver for the MCP16502 PMIC.
This drivers supports basic operations through the
regulator interface such as:
- setting/reading voltage
- setting/reading operating mode
- reading current status
Signed-off-by: Andrei Stefanescu <andrei.stefanescu@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch adds a maintainer for the MCP16502 PMIC
driver.
Signed-off-by: Andrei Stefanescu <andrei.stefanescu@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch describes the compatible and the device tree
bindings necessary for the MCP16502 PMIC.
Signed-off-by: Andrei Stefanescu <andrei.stefanescu@microchip.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add sound/soc/meson drivers entry for Amlogic audio drivers.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add support for the spdif input decoder of the axg SoC family
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add the DT binding documentation for axg's SPDIF input.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
add IEC958_SUBFRAME_LE to the list of format accepted by the fifo frontend.
As opposed to what was initially noted in the toddr dai driver, the spdifin
does not place the msb at bit 28, it just output a whole spdif subframe.
Placing the msb at bit 28 in the toddr driver just filters out the parity,
user, channel status and validity bits. It is better to just provide the
whole spdif subframe to the userspace and let the iec958 plugin deal with
it.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
With the new validation code, a malicious user-space app could
potentially submit command streams with enough buffer-object and resource
references in them to have the resulting allocated validion nodes and
relocations make the kernel run out of GFP_KERNEL memory.
Protect from this by having the validation code reserve TTM graphics
memory when allocating.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Deepak Rawat <drawat@vmware.com>
---
v2: Removed leftover debug printouts
|
|
Add introductions of interrupt-parent and spi-slave.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Configure watermark to change with the length of the sent data.
Support LPSPI sending message shorter than tx/rxfifosize.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add slave mode support to the fsl-lpspi driver, only in PIO mode.
For now, there are some limitations for slave mode transmission:
1. The stale data in RXFIFO will be dropped when the Slave does any new
transfer.
2. One transfer can be finished only after all transfer->len data been
transferred to master device
3. Slave device only accepts transfer->len data. Any data longer than
this from master device will be dropped. Any data shorter than this
from master will cause LPSPI to stuck due to mentioned limitation 2.
4. Only PIO transfer is supported in Slave Mode.
Wire connection:
GND, SCK, MISO(to MISO of slave), MOSI(to MOSI of slave), SCS
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In order to enable the slave mode and make the code more readable,
replace all related structure names and object names which is
named "master" with "controller".
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
asoc_simple_card_probe
Commit 4fb7f4df49d3 ("ASoC: simple-card: use cpu/codec pointer on
simple_dai_props") updated {cpu,codec}_dai to be pointers in struct
simple_dai_props but didn't update these locations to dereference the
pointers.
This patch fixup it for non DT simple-card use case.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fix the spelling of "transmitter".
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
eukrea-tlv320.c machine driver runs on non-DT platforms
and include <asm/mach-types.h> header file in order to be able
to use some machine_is_eukrea_xxx() macros.
Building it for ARM64 causes the following build error:
sound/soc/fsl/eukrea-tlv320.c:28:10: fatal error: asm/mach-types.h: No such file or directory
Avoid this error by not allowing to build the SND_SOC_EUKREA_TLV320
driver when ARM64 is selected.
This is needed in preparation for the i.MX8M support.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Added USB serial option driver support for Fibocom NL668 series cellular
modules. Reserved USB endpoints 4, 5 and 6 for network + ADB interfaces.
usb-devices output (QMI mode)
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 16 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1508 ProdID=1001 Rev=03.18
S: Manufacturer=Nodecom NL668 Modem
S: Product=Nodecom NL668-CN Modem
S: SerialNumber=
C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
usb-devices output (ECM mode)
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 17 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1508 ProdID=1001 Rev=03.18
S: Manufacturer=Nodecom NL668 Modem
S: Product=Nodecom NL668-CN Modem
S: SerialNumber=
C: #Ifs= 7 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 4 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether
I: If#= 5 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
I: If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
Signed-off-by: Jörgen Storvist <jorgen.storvist@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
This patch adds support for suniv Allwinner ARMv5 F1C100s SoC which has
stripped version of interrupt controller that found in A10/A13.
Signed-off-by: Mesih Kilinc <mesihkilinc@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
This patch moves IC specific register offsets to sun4i_irq_chip_data
struct in order to support different chips.
Signed-off-by: Mesih Kilinc <mesihkilinc@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
In order to support different chips, IC specific data should be hold in
a struct. This patch moves irq_base and irq_domain global variables to
struct.
Signed-off-by: Mesih Kilinc <mesihkilinc@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Add compatible string for Alwinner suniv F1C100s SoC interrupt
controller which is stripped version of sun4i
Signed-off-by: Mesih Kilinc <mesihkilinc@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Add interrupt driver for RDA Micro RDA8810PL SoC.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Document interrupt controller in RDA Micro RDA8810PL SoC.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
