| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
This frees up some bits to hold more high level info such as PAE being
present, w/o increasing the size of already bloated cpuinfo struct
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
It was generating warnings when called as write_aux_reg(x, paddr >> 32)
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
This is done by improving the laddering logic !
Before:
if Exception
goto excep_or_pure_k_ret
if !Interrupt(L2)
goto l1_chk
else
INTERRUPT_EPILOGUE 2
l1_chk:
if !Interrupt(L1) (i.e. pure kernel mode)
goto excep_or_pure_k_ret
else
INTERRUPT_EPILOGUE 1
excep_or_pure_k_ret:
EXCEPTION_EPILOGUE
Now:
if !Interrupt(L1 or L2) (i.e. exception or pure kernel mode)
goto excep_or_pure_k_ret
; guaranteed to be an interrupt
if !Interrupt(L2)
goto l1_ret
else
INTERRUPT_EPILOGUE 2
; by virtue of above, no need to chk for L1 active
l1_ret:
INTERRUPT_EPILOGUE 1
excep_or_pure_k_ret:
EXCEPTION_EPILOGUE
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
The requirement is to
- Reenable Exceptions (AE cleared)
- Reenable Interrupts (E1/E2 set)
We need to do wiggle these bits into ERSTATUS and call RTIE.
Prev version used the pre-exception STATUS32 as starting point for what
goes into ERSTATUS. This required explicit fixups of U/DE/L bits.
Instead, use the current (in-exception) STATUS32 as starting point.
Being in exception handler U/DE/L can be safely assumed to be correct.
Only AE/E1/E2 need to be fixed.
So the new implementation is slightly better
-Avoids read form memory
-Is 4 bytes smaller for the typical 1 level of intr configuration
-Depicts the semantics more clearly
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
Historically this was done by ARC IDE driver, which is long gone.
IRQ core is pretty robust now and already checks if IRQs are enabled
in hard ISRs. Thus no point in checking this in arch code, for every
call of irq enabled.
Further if some driver does do that - let it bring down the system so we
notice/fix this sooner than covering up for sucker
This makes local_irq_enable() - for L1 only case atleast simple enough
so we can inline it.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
Implement the TLB flush routine to evict a sepcific Super TLB entry,
vs. moving to a new ASID on every such flush.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
ARCHes with special requirements for evicting THP backing TLB entries
can implement this.
Otherwise also, it can help optimize TLB flush in THP regime.
stock flush_tlb_range() typically has optimization to nuke the entire
TLB if flush span is greater than a certain threshhold, which will
likely be true for a single huge page. Thus a single thp flush will
invalidate the entrire TLB which is not desirable.
e.g. see arch/arc: flush_pmd_tlb_range
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Link: http://lkml.kernel.org/r/20151009100816.GC7873@node
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
- pgtable-generic.c: Fold individual #ifdef for each helper into a top
level #ifdef. Makes code more readable
- Converted the stub helpers for !THP to BUILD_BUG() vs. runtime BUG()
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Link: http://lkml.kernel.org/r/20151009133450.GA8597@node
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
This reduces/simplifies the diff for the next patch which moves THP
specific code.
No semantical changes !
Acked-by: Kirill A. Shutemov kirill.shutemov@linux.intel.com
Link: http://lkml.kernel.org/r/1442918096-17454-9-git-send-email-vgupta@synopsys.com
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
MMUv4 in HS38x cores supports Super Pages which are basis for Linux THP
support.
Normal and Super pages can co-exist (ofcourse not overlap) in TLB with a
new bit "SZ" in TLB page desciptor to distinguish between them.
Super Page size is configurable in hardware (4K to 16M), but fixed once
RTL builds.
The exact THP size a Linx configuration will support is a function of:
- MMU page size (typical 8K, RTL fixed)
- software page walker address split between PGD:PTE:PFN (typical
11:8:13, but can be changed with 1 line)
So for above default, THP size supported is 8K * 256 = 2M
Default Page Walker is 2 levels, PGD:PTE:PFN, which in THP regime
reduces to 1 level (as PTE is folded into PGD and canonically referred
to as PMD).
Thus thp PMD accessors are implemented in terms of PTE (just like sparc)
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
Greg reported crashes hitting the following check in __sk_backlog_rcv()
BUG_ON(!sock_flag(sk, SOCK_MEMALLOC));
The pfmemalloc bit is currently checked in sk_filter().
This works correctly for TCP, because sk_filter() is ran in
tcp_v[46]_rcv() before hitting the prequeue or backlog checks.
For UDP or other protocols, this does not work, because the sk_filter()
is ran from sock_queue_rcv_skb(), which might be called _after_ backlog
queuing if socket is owned by user by the time packet is processed by
softirq handler.
Fixes: b4b9e35585089 ("netvm: set PF_MEMALLOC as appropriate during SKB processing")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Greg Thelen <gthelen@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 00590fdd5be0 introduced RCU locking in list type and in
doing so introduced a memory allocation in list_set_add, which
is done in an atomic context, due to the fact that ipset rcu
list modifications are serialised with a spin lock. The reason
why we can't use a mutex is that in addition to modifying the
list with ipset commands, it's also being modified when a
particular ipset rule timeout expires aka garbage collection.
This gc is triggered from set_cleanup_entries, which in turn
is invoked from a timer thus requiring the lock to be bh-safe.
Concretely the following call chain can lead to "sleeping function
called in atomic context" splat:
call_ad -> list_set_uadt -> list_set_uadd -> kzalloc(, GFP_KERNEL).
And since GFP_KERNEL allows initiating direct reclaim thus
potentially sleeping in the allocation path.
To fix the issue change the allocation type to GFP_ATOMIC, to
correctly reflect that it is occuring in an atomic context.
Fixes: 00590fdd5be0 ("netfilter: ipset: Introduce RCU locking in list type")
Signed-off-by: Nikolay Borisov <kernel@kyup.com>
Acked-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
We received several reports of systems rebooting and powering on
after an attempted shutdown. Testing showed that setting
XHCI_SPURIOUS_WAKEUP quirk in addition to the XHCI_SPURIOUS_REBOOT
quirk allowed the system to shutdown as expected for LynxPoint-LP
xHCI controllers. Set the quirk back.
Note that the quirk was originally introduced for LynxPoint and
LynxPoint-LP just for this same reason. See:
commit 638298dc66ea ("xhci: Fix spurious wakeups after S5 on Haswell")
It was later limited to only concern HP machines as it caused
regression on some machines, see both bug and commit:
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=66171
commit 6962d914f317 ("xhci: Limit the spurious wakeup fix only to HP machines")
Later it was discovered that the powering on after shutdown
was limited to LynxPoint-LP (Haswell-ULT) and that some non-LP HP
machine suffered from spontaneous resume from S3 (which should
not be related to the SPURIOUS_WAKEUP quirk at all). An attempt
to fix this then removed the SPURIOUS_WAKEUP flag usage completely.
commit b45abacde3d5 ("xhci: no switching back on non-ULT Haswell")
Current understanding is that LynxPoint-LP (Haswell ULT) machines
need the SPURIOUS_WAKEUP quirk, otherwise they will restart, and
plain Lynxpoint (Haswell) machines may _not_ have the quirk
set otherwise they again will restart.
Signed-off-by: Laura Abbott <labbott@fedoraproject.org>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Oliver Neukum <oneukum@suse.com>
[Added more history to commit message -Mathias]
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If a host fails to wake up a isochronous SuperSpeed device from U1/U2
in time for a isoch transfer it will generate a "No ping response error"
Host will then move to the next transfer descriptor.
Handle this case in the same way as missed service errors, tag the
current TD as skipped and handle it on the next transfer event.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If the difference is big enough between the bytes asked and received
in a bulk transfer we can get a short transfer event pointing to a TRB in
the middle of the TD. We don't want to handle the TD yet as we will anyway
receive a new event for the last TRB in the TD.
Hold off from finishing the TD and removing it from the list until we
receive an event for the last TRB in the TD
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes for the 4.3 cycle.
* twl4030 - incorrect readings for some channels due to a failure to
initialize a bias regulator or configure the lines for input rather than
USB use.
* lis3lv02 - a missunderstanding of the way the interrupts worked on this
chip lead to activation of the wrong interrupt.
* sca3000 - an old bug meant that memory corruption could occur in the
hardware ring buffer readout function.
* mxs-lradc - wrong temp offset.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
"Just two small fixups to ads7846 touchscreen controller driver and
Cypress touchpad driver"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: cyapa - fix the copy paste error on electrodes_rx value
Input: ads7846 - correct the value got from SPI
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fix from Stephen Boyd:
"Just one revert for Armada XP devices: the conversion to
of_clk_get_parent_name() wasn't a direct translation, so we
revert back to of_clk_get() + __clk_get_name().
We could make of_clk_get_parent_name() more robust, but that
may have unintended side-effects, so we'll do that in the
next version"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
Partially revert "clk: mvebu: Convert to clk_hw based provider APIs"
|
|
The value of emul_con was getting overwritten if the selected soc is
SOC_ARCH_EXYNOS5260. And so as a result we were reading from the wrong
register in the case of SOC_ARCH_EXYNOS5260.
Fixes: 488c7455d74c ("thermal: exynos: Add the support for Exynos5433 TMU")
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
When CONFIG_PM is not set we get following compilation warnings:
warning: ‘byt_gpio_runtime_suspend’ defined but not used [-Wunused-function]
warning: ‘byt_gpio_runtime_resume’ defined but not used [-Wunused-function]
Fix this by guarding byt_gpio_runtime_suspend()/byt_gpio_runtime_resume()
with #ifdef CONFIG_PM.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
We get following warning when CONFIG_PM_SLEEP is not set
warning: ‘intel_gpio_irq_init’ defined but not used [-Wunused-function]
Since the function is only called from intel_pinctrl_resume() move it
inside CONFIG_PM_SLEEP guard as well.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The flag matches the DT GPIO_SINGLE_ENDED flag and allows drivers to
parse and use the DT flag to handle single-ended (open-drain or
open-source) GPIOs.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
When requesting a GPIO through the legacy or the gpiod_* API the
gpiochip request operation is first called and then the GPIO flags are
parsed and the GPIO is configured. This prevents the gpiochip from
rejecting the request if the flags are not supported by the device.
To fix this split the parse-and-configure operation in two and parse
flags before requesting the GPIO.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The DEBUG_FS=n #defines for the dbg_show functions were missed when
renaming the driver from msm_ to pm8xxx_, causing it to break the build
when DEBUG_FS isn't enabled:
CC [M] drivers/pinctrl/qcom/pinctrl-ssbi-gpio.o
drivers/pinctrl/qcom/pinctrl-ssbi-gpio.c:597:14: error: ‘pm8xxx_gpio_dbg_show’ undeclared here (not in a function)
.dbg_show = pm8xxx_gpio_dbg_show,
Fix this by renaming them correctly.
Fixes: b4c45fe974bc ("pinctrl: qcom: ssbi: Family A gpio & mpp drivers")
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Replace all trivial request/free callbacks that do nothing but call into
pinctrl code with the generic versions.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Eric Anholt <eric@anholt.net>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Lee Jones <lee@kernel.org>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Instead of storing in the chip data whether the chip uses pinctrl and
conditionally call pinctrl_{request,free}_gpio, just don't populate
request/free in that case.
This makes the implementations trivial and the same as the generic
implementations, thus we can just use them.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Instead of storing in the chip data whether the chip uses pinctrl and
conditionally call pinctrl_{request,free}_gpio, just don't populate
request/free in that case.
This makes the implementations trivial and the same as the generic
implementations, thus we can just use them.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Replace all trivial request/free callbacks that do nothing but call into
pinctrl code with the generic versions.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Acked-by: Joachim Eastwood <manabian@gmail.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Provide generic request/free implementations that pinctrl aware gpio
drivers can use instead of open coding if they use a 1:1 pin to gpio
signal mapping.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
"Two DM target error path cleanup fixes (one for stable in DM thinp and
one for a v4.3-rc5 thinko in DM snapshot)"
* tag 'dm-4.3-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm thin: fix missing pool reference count decrement in pool_ctr error path
dm snapshot persistent: fix missing cleanup in persistent_ctr error path
|
|
The the pin groups and pin functions have been changed
in atlas7 step B soc. We have to update the driver
to support step B chip.
Changes:
1. add 5 jtag pins to IOC_TOP:
"jtag_tdo", "jtag_tms","jtag_tck", "jtag_tdi", "jtag_trstn"
these 5 pins can be mutiplex with other functions, so we
have to conver these 5 pins in pinmux.
2. add pin groups for audio digmic, audio spdif, can transceiver
en, can transceiver stb, i2s0, i2s1 and jtag.
3. serval pins can be located to more PADs:
audio_uart0_urfs, audio_uart1_urfs, audio_uart2_urfs,
audio_uart2_urxd, audio_uart2_usclk, audio_uart2_utfs,
audio_uart2_utxd, can0_rxd, can0_txd, can1_rxd, can1_txd
jtag_ntrst, jtag_swdiotms, jtag_tck, jtag_tdi, jtag_tdo,
pw_cko0, pw_cko1, pw_i2s01, pw_pwm0, pw_pwm1, sd2_cdb,
sd2_wpb, uart2_cts, uart2_rts, uart2_rxd, uart2_txd,
uart3_cts, uart3_rts, uart3_rxd, uart3_txd, uart4_cts,
uart4_rts, usb0_drvvbus, usb1_drvvbus.
Because of Changes#3, some functions should have more than one
pin groups. So we have to split the original pin group to serval
pin groups.
For example:
audio_uart0 has 5 pins, on STEPA, each of these 5 pins only has
one related PAD. But on STEPB, audio_uart0_urfs has 4 related
PAD.
So we place the 4 pins with one PAD into a single pin group:
audio_uart0_basic_group.
and place urfs pin wtih different PADs to 4 different pin groups:
audio_uart0_urfs_group0, ..., audio_uart0_urfs_group3
A full audio_uart0 pin group can be:
pinctrl-0 = <&audio_uart0_basic_group &audio_uart0_urfs_group0>;
If audio_uart0 pin group encountered some confiction, we only have
to change the urfs group:
pinctrl-0 = <&audio_uart0_basic_group &audio_uart0_urfs_group2>;
Signed-off-by: Wei Chen <Wei.Chen@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"I have two more bug fixes for btrfs.
My commit fixes a bug we hit last week at FB, a combination of lots of
hard links and an admin command to resolve inode numbers.
Dave is adding checks to make sure balance on current kernels ignores
filters it doesn't understand. The penalty for being wrong is just
doing more work (not crashing etc), but it's a good fix"
* 'for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: fix use after free iterating extrefs
btrfs: check unsupported filters in balance arguments
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull Ceph fixes from Sage Weil:
"Just two small items from Ilya:
The first patch fixes the RBD readahead to grab full objects. The
second fixes the write ops to prevent undue promotion when a cache
tier is configured on the server side"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
rbd: use writefull op for object size writes
rbd: set max_sectors explicitly
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These fix two recent regressions (ACPICA, the generic power domains
framework) and one crash that may happen on specific hardware
supported since 4.1 (intel_pstate).
Specifics:
- Fix a regression introduced by a recent ACPICA cleanup that
uncovered a latent bug (Lv Zheng).
- Fix a recent regression in the generic power domains framework that
may cause it to violate PM QoS latency constraints in some cases
(Ulf Hansson).
- Fix an intel_pstate driver crash on the Knights Landing chips that
do not update the MPERF counter as often as expected by the driver
which may result in a divide by 0 (Srinivas Pandruvada)"
* tag 'pm+acpi-4.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: intel_pstate: Fix divide by zero on Knights Landing (KNL)
ACPICA: Tables: Fix FADT dependency regression
PM / Domains: Fix validation of latency constraints in genpd governor
|
|
Pull drm fixes from Dave Airlie:
"Nothing too crazy or exciting:
- two MAINTAINERS entries that I didn't see the point in delaying.
- one drm mst fix to stop sending uninitialised data to monitors
- two amdgpu fixes
- one radeon mst tiling fix
- one vmwgfx regression fix
- one virtio warning fix.
I have found one locking problem that needs a bit of reorg to fix, but
I'm not sure it's worth putting in -fixes as I don't think we've seen
it hit in the real world ever, I just found it using the virtio-gpu
driver when working on it. I'll possibly send it next week once I've
time to discuss with Daniel"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/virtio: use %llu format string form atomic64_t
MAINTAINERS: Add myself as maintainer for the gma500 driver
MAINTAINERS: add a maintainer for the atmel-hlcdc DRM driver
drm/amdgpu: Keep the pflip interrupts always enabled v7
drm/amdgpu: adjust default dispclk (v2)
drm/dp/mst: make mst i2c transfer code more robust.
drm/radeon: attach tile property to mst connector
drm/vmwgfx: Fix kernel NULL pointer dereference on older hardware
|
|
On boards with more than 2GB of RAM booting goes wrong with things not
working and we're getting lots of l3 warnings:
WARNING: CPU: 0 PID: 1 at drivers/bus/omap_l3_noc.c:147
l3_interrupt_handler+0x260/0x384()
44000000.ocp:L3 Custom Error: MASTER MMC6 TARGET DMM1 (Idle):
Data Access in User mode during Functional access
...
[<c044e158>] (scsi_add_host_with_dma) from [<c04705c8>]
(ata_scsi_add_hosts+0x5c/0x18c)
[<c04705c8>] (ata_scsi_add_hosts) from [<c046b13c>]
(ata_host_register+0x150/0x2cc)
[<c046b13c>] (ata_host_register) from [<c046b38c>]
(ata_host_activate+0xd4/0x124)
[<c046b38c>] (ata_host_activate) from [<c047f42c>]
(ahci_host_activate+0x5c/0x194)
[<c047f42c>] (ahci_host_activate) from [<c0480854>]
(ahci_platform_init_host+0x1f0/0x3f0)
[<c0480854>] (ahci_platform_init_host) from [<c047c9dc>]
(ahci_probe+0x70/0x98)
[<c047c9dc>] (ahci_probe) from [<c04220cc>]
(platform_drv_probe+0x54/0xb4)
Let's fix the issue by enabling ZONE_DMA for LPAE. Note that we need to
limit dma_zone_size to 2GB as the rest of the RAM is beyond the 4GB limit.
Let's also fix things for dra7 as done in similar patches in the TI tree
by Lokesh Vutla <lokeshvutla@ti.com>.
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Re-enable CONFIG_SCSI_DH in our defconfigs
- Remove unused os_area_db_id_video_mode
- cxl: fix leak of IRQ names in cxl_free_afu_irqs() from Andrew
- cxl: fix leak of ctx->irq_bitmap when releasing context via kernel API from Andrew
- cxl: fix leak of ctx->mapping when releasing kernel API contexts from Andrew
- cxl: Workaround malformed pcie packets on some cards from Philippe
- cxl: Fix number of allocated pages in SPA from Christophe Lombard
- Fix checkstop in native_hpte_clear() with lockdep from Cyril
- Panic on unhandled Machine Check on powernv from Daniel
- selftests/powerpc: Fix build failure of load_unaligned_zeropad test
* tag 'powerpc-4.3-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
selftests/powerpc: Fix build failure of load_unaligned_zeropad test
powerpc/powernv: Panic on unhandled Machine Check
powerpc: Fix checkstop in native_hpte_clear() with lockdep
cxl: Fix number of allocated pages in SPA
cxl: Workaround malformed pcie packets on some cards
cxl: fix leak of ctx->mapping when releasing kernel API contexts
cxl: fix leak of ctx->irq_bitmap when releasing context via kernel API
cxl: fix leak of IRQ names in cxl_free_afu_irqs()
powerpc/ps3: Remove unused os_area_db_id_video_mode
powerpc/configs: Re-enable CONFIG_SCSI_DH
|
|
Merge misc fixes from Andrew Morton:
"6 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
sh: add copy_user_page() alias for __copy_user()
lib/Kconfig: ZLIB_DEFLATE must select BITREVERSE
mm, dax: fix DAX deadlocks
memcg: convert threshold to bytes
builddeb: remove debian/files before build
mm, fs: obey gfp_mapping for add_to_page_cache()
|
|
copy_user_page() is needed by DAX. Without this we get a compile error
for DAX on SH:
fs/dax.c:280:2: error: implicit declaration of function `copy_user_page' [-Werror=implicit-function-declaration]
copy_user_page(vto, (void __force *)vfrom, vaddr, to);
^
This was done with a random config that happened to include DAX support.
This patch has only been compile tested.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Matthew Wilcox <willy@linux.intel.com>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
lib/built-in.o: In function `__bitrev32':
deftree.c:(.text+0x1e799): undefined reference to `byte_rev_table'
deftree.c:(.text+0x1e7a0): undefined reference to `byte_rev_table'
deftree.c:(.text+0x1e7b4): undefined reference to `byte_rev_table'
deftree.c:(.text+0x1e7c1): undefined reference to `byte_rev_table'
Anything which uses bitrevX() has to select BITREVERSE, to grab
lib/bitrev.o.
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The following two locking commits in the DAX code:
commit 843172978bb9 ("dax: fix race between simultaneous faults")
commit 46c043ede471 ("mm: take i_mmap_lock in unmap_mapping_range() for DAX")
introduced a number of deadlocks and other issues which need to be fixed
for the v4.3 kernel. The list of issues in DAX after these commits
(some newly introduced by the commits, some preexisting) can be found
here:
https://lkml.org/lkml/2015/9/25/602 (Subject: "Re: [PATCH] dax: fix deadlock in __dax_fault").
This undoes most of the changes introduced by those two commits,
essentially returning us to the DAX locking scheme that was used in
v4.2.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Dan Williams <dan.j.williams@intel.com>
Tested-by: Dave Chinner <dchinner@redhat.com>
Cc: Jan Kara <jack@suse.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Matthew Wilcox <matthew.r.wilcox@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
page_counter_memparse() returns pages for the threshold, while
mem_cgroup_usage() returns bytes for memory usage. Convert the
threshold to bytes.
Fixes: 3e32cb2e0a12b6915 ("memcg: rename cgroup_event to mem_cgroup_event").
Signed-off-by: Shaohua Li <shli@fb.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 3716001bcb7f ("deb-pkg: add source package") added the ability to
create a debian changelog file. This exposed that previously the
builddeb script hasn't cleared debian/files between builds.
As debian/files keeps accumulating entries, the changes file will end up
growing indefinelty. With outdated entries in debian/files, builddeb
script will exit with failure. This regression impacts those who use
"make deb-pkg" target to build kernel into a .deb package and never use
"make mrproper" or other means to clean kernel tree from generated
directories.
To fix the regression, remove debian/files before starting build and in
the generated clean rule.
Fixes: 3716001bcb7f ("deb-pkg: add source package")
Signed-off-by: Riku Voipio <riku.voipio@linaro.org>
Reported-by: Doug Smythies <dsmythies@telus.net>
Tested-by: Doug Smythies <dsmythies@telus.net>
Tested-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Michal Marek <mmarek@suse.cz>
Cc: maximilian attems <maks@stro.at>
Cc: Chris J Arges <chris.j.arges@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
