summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2023-05-16vmlinux.lds.h: Discard .note.gnu.property sectionJosh Poimboeuf
When tooling reads ELF notes, it assumes each note entry is aligned to the value listed in the .note section header's sh_addralign field. The kernel-created ELF notes in the .note.Linux and .note.Xen sections are aligned to 4 bytes. This causes the toolchain to set those sections' sh_addralign values to 4. On the other hand, the GCC-created .note.gnu.property section has an sh_addralign value of 8 for some reason, despite being based on struct Elf32_Nhdr which only needs 4-byte alignment. When the mismatched input sections get linked together into the vmlinux .notes output section, the higher alignment "wins", resulting in an sh_addralign of 8, which confuses tooling. For example: $ readelf -n .tmp_vmlinux.btf ... readelf: .tmp_vmlinux.btf: Warning: note with invalid namesz and/or descsz found at offset 0x170 readelf: .tmp_vmlinux.btf: Warning: type: 0x4, namesize: 0x006e6558, descsize: 0x00008801, alignment: 8 In this case readelf thinks there's alignment padding where there is none, so it starts reading an ELF note in the middle. With newer toolchains (e.g., latest Fedora Rawhide), a similar mismatch triggers a build failure when combined with CONFIG_X86_KERNEL_IBT: btf_encoder__encode: btf__dedup failed! Failed to encode BTF libbpf: failed to find '.BTF' ELF section in vmlinux FAILED: load BTF from vmlinux: No data available make[1]: *** [scripts/Makefile.vmlinux:35: vmlinux] Error 255 This latter error was caused by pahole crashing when it encountered the corrupt .notes section. This crash has been fixed in dwarves version 1.25. As Tianyi Liu describes: "Pahole reads .notes to look for LINUX_ELFNOTE_BUILD_LTO. When LTO is enabled, pahole needs to call cus__merge_and_process_cu to merge compile units, at which point there should only be one unspecified type (used to represent some compilation information) in the global context. However, when the kernel is compiled without LTO, if pahole calls cus__merge_and_process_cu due to alignment issues with notes, multiple unspecified types may appear after merging the cus, and older versions of pahole only support up to one. This is why pahole 1.24 crashes, while newer versions support multiple. However, the latest version of pahole still does not solve the problem of incorrect LTO recognition, so compiling the kernel may be slower than normal." Even with the newer pahole, the note section misaligment issue still exists and pahole is misinterpreting the LTO note. Fix it by discarding the .note.gnu.property section. While GNU properties are important for user space (and VDSO), they don't seem to have any use for vmlinux. (In fact, they're already getting (inadvertently) stripped from vmlinux when CONFIG_DEBUG_INFO_BTF is enabled. The BTF data is extracted from vmlinux.o with "objcopy --only-section=.BTF" into .btf.vmlinux.bin.o. That file doesn't have .note.gnu.property, so when it gets modified and linked back into the main object, the linker automatically strips it (see "How GNU properties are merged" in the ld man page).) Reported-by: Daniel Xu <dxu@dxuuu.xyz> Link: https://lkml.kernel.org/bpf/57830c30-cd77-40cf-9cd1-3bb608aa602e@app.fastmail.com Debugged-by: Tianyi Liu <i.pear@outlook.com> Suggested-by: Joan Bruguera Micó <joanbrugueram@gmail.com> Link: https://lore.kernel.org/r/20230418214925.ay3jpf2zhw75kgmd@treble Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
2023-05-16arm64: dts: imx8: fix USB 3.0 Gadget Failure in QM & QXPB0 at super speedFrank Li
Resolve USB 3.0 gadget failure for QM and QXPB0 in super speed mode with single IN and OUT endpoints, like mass storage devices, due to incorrect ACTUAL_MEM_SIZE in ep_cap2 (32k instead of actual 18k). Implement dt property cdns,on-chip-buff-size to override ep_cap2 and set it to 18k for imx8QM and imx8QXP chips. No adverse effects for 8QXP C0. Cc: stable@vger.kernel.org Fixes: dce49449e04f ("usb: cdns3: allocate TX FIFO size according to composite EP number") Signed-off-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2023-05-16dt-binding: cdns,usb3: Fix cdns,on-chip-buff-size typeFrank Li
In cdns3-gadget.c, 'cdns,on-chip-buff-size' was read using device_property_read_u16(). It resulted in 0 if a 32bit value was used in dts. This commit fixes the dt binding doc to declare it as u16. Cc: stable@vger.kernel.org Fixes: 68989fe1c39d ("dt-bindings: usb: Convert cdns-usb3.txt to YAML schema") Signed-off-by: Frank Li <Frank.Li@nxp.com> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2023-05-16irqchip/mbigen: Unify the error handling in mbigen_of_create_domain()Kefeng Wang
Dan Carpenter reported that commit fea087fc291b "irqchip/mbigen: move to use bus_get_dev_root()" leads to the following Smatch static checker warning: drivers/irqchip/irq-mbigen.c:258 mbigen_of_create_domain() error: potentially dereferencing uninitialized 'child'. It should not cause a problem on real hardware, but better to fix the warning, let's move the bus_get_dev_root() out of the loop, and unify the error handling to silence it. Reported-by: Dan Carpenter <dan.carpenter@linaro.org> Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20230505090654.12793-1-wangkefeng.wang@huawei.com
2023-05-16irqchip/meson-gpio: Mark OF related data as maybe unusedKrzysztof Kozlowski
The driver can be compile tested with !CONFIG_OF making certain data unused: drivers/irqchip/irq-meson-gpio.c:153:34: error: ‘meson_irq_gpio_matches’ defined but not used [-Werror=unused-const-variable=] Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20230512164506.212267-1-krzysztof.kozlowski@linaro.org
2023-05-16irqchip/mips-gic: Use raw spinlock for gic_lockJiaxun Yang
Since we may hold gic_lock in hardirq context, use raw spinlock makes more sense given that it is for low-level interrupt handling routine and the critical section is small. Fixes BUG: [ 0.426106] ============================= [ 0.426257] [ BUG: Invalid wait context ] [ 0.426422] 6.3.0-rc7-next-20230421-dirty #54 Not tainted [ 0.426638] ----------------------------- [ 0.426766] swapper/0/1 is trying to lock: [ 0.426954] ffffffff8104e7b8 (gic_lock){....}-{3:3}, at: gic_set_type+0x30/08 Fixes: 95150ae8b330 ("irqchip: mips-gic: Implement irq_set_type callback") Cc: stable@vger.kernel.org Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com> Reviewed-by: Serge Semin <fancer.lancer@gmail.com> Tested-by: Serge Semin <fancer.lancer@gmail.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20230424103156.66753-3-jiaxun.yang@flygoat.com
2023-05-16irqchip/mips-gic: Don't touch vl_map if a local interrupt is not routableJiaxun Yang
When a GIC local interrupt is not routable, it's vl_map will be used to control some internal states for core (providing IPTI, IPPCI, IPFDC input signal for core). Overriding it will interfere core's intetrupt controller. Do not touch vl_map if a local interrupt is not routable, we are not going to remap it. Before dd098a0e0319 (" irqchip/mips-gic: Get rid of the reliance on irq_cpu_online()"), if a local interrupt is not routable, then it won't be requested from GIC Local domain, and thus gic_all_vpes_irq_cpu_online won't be called for that particular interrupt. Fixes: dd098a0e0319 (" irqchip/mips-gic: Get rid of the reliance on irq_cpu_online()") Cc: stable@vger.kernel.org Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com> Reviewed-by: Serge Semin <fancer.lancer@gmail.com> Tested-by: Serge Semin <fancer.lancer@gmail.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20230424103156.66753-2-jiaxun.yang@flygoat.com
2023-05-16irqchip/gic-v3: Disable pseudo NMIs on Mediatek devices w/ firmware issuesDouglas Anderson
Some Chromebooks with Mediatek SoCs have a problem where the firmware doesn't properly save/restore certain GICR registers. Newer Chromebooks should fix this issue and we may be able to do firmware updates for old Chromebooks. At the moment, the only known issue with these Chromebooks is that we can't enable "pseudo NMIs" since the priority register can be lost. Enabling "pseudo NMIs" on Chromebooks with the problematic firmware causes crashes and freezes. Let's detect devices with this problem and then disable "pseudo NMIs" on them. We'll detect the problem by looking for the presence of the "mediatek,broken-save-restore-fw" property in the GIC device tree node. Any devices with fixed firmware will not have this property. Our detection plan works because we never bake a Chromebook's device tree into firmware. Instead, device trees are always bundled with the kernel. We'll update the device trees of all affected Chromebooks and then we'll never enable "pseudo NMI" on a kernel that is bundled with old device trees. When a firmware update is shipped that fixes this issue it will know to patch the device tree to remove the property. In order to make this work, the quick detection mechanism of the GICv3 code is extended to be able to look for properties in addition to looking at "compatible". Reviewed-by: Julius Werner <jwerner@chromium.org> Signed-off-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20230515131353.v2.2.I88dc0a0eb1d9d537de61604cd8994ecc55c0cac1@changeid
2023-05-16dt-bindings: interrupt-controller: arm,gic-v3: Add quirk for Mediatek SoCs ↵Douglas Anderson
w/ broken FW When trying to turn on the "pseudo NMI" kernel feature in Linux, it was discovered that all Mediatek-based Chromebooks that ever shipped (at least ones with GICv3) had a firmware bug where they wouldn't save certain GIC "GICR" registers properly. If a processor ever entered a suspend/idle mode where the GICR registers lost state then they'd be reset to their default state. As a result of the bug, if you try to enable "pseudo NMIs" on the affected devices then certain interrupts will unexpectedly get promoted to be "pseudo NMIs" and cause crashes / freezes / general mayhem. ChromeOS is looking to start turning on "pseudo NMIs" in production to make crash reports more actionable. To do so, we will release firmware updates for at least some of the affected Mediatek Chromebooks. However, even when we update the firmware of a Chromebook it's always possible that a user will end up booting with old firmware. We need to be able to detect when we're running with firmware that will crash and burn if pseudo NMIs are enabled. The current plan is: * Update the device trees of all affected Chromebooks to include the 'mediatek,broken-save-restore-fw' property. The kernel can use this to know not to enable certain features like "pseudo NMI". NOTE: device trees for Chromebooks are never baked into the firmware but are bundled with the kernel. A kernel will never be configured to use "pseudo NMIs" and be bundled with an old device tree. * When we get a fixed firmware for one of these Chromebooks, it will patch the device tree to remove this property. For some details, you can also see the public bug <https://issuetracker.google.com/281831288> Reviewed-by: Julius Werner <jwerner@chromium.org> Signed-off-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20230515131353.v2.1.Iabe67a827e206496efec6beb5616d5a3b99c1e65@changeid
2023-05-16drm/pl111: Fix FB depth on IMPD-1 framebufferLinus Walleij
The last argument to the function drm_fbdev_dma_setup() was changed from desired BPP to desired depth. In our case the desired depth was 15 but BPP was 16, so we specified 16 as BPP and we relied on the FB emulation core to select a format with a suitable depth for the limited bandwidth and end up with e.g. XRGB1555 like in the past: [drm] Initialized pl111 1.0.0 20170317 for c1000000.display on minor 0 drm-clcd-pl111 c1000000.display: [drm] requested bpp 16, scaled depth down to 15 drm-clcd-pl111 c1000000.display: enable IM-PD1 CLCD connectors Console: switching to colour frame buffer device 80x30 drm-clcd-pl111 c1000000.display: [drm] fb0: pl111drmfb frame buffer device However the current code will fail at that: [drm] Initialized pl111 1.0.0 20170317 for c1000000.display on minor 0 drm-clcd-pl111 c1000000.display: [drm] bpp/depth value of 16/16 not supported drm-clcd-pl111 c1000000.display: [drm] No compatible format found drm-clcd-pl111 c1000000.display: [drm] *ERROR* fbdev: Failed to setup generic emulation (ret=-12) Fix this by passing the desired depth of 15 for the IM/PD-1 display instead of 16 to drm_fbdev_dma_setup(). The desired depth is however in turn used for bandwidth limiting calculations and that was done with a simple / integer division, whereas we now have to modify that to use DIV_ROUND_UP() so that we get DIV_ROUND_UP(15, 2) = 2 not 15/2 = 1. After this the display works again on the Integrator/AP IM/PD-1. Cc: Emma Anholt <emma@anholt.net> Cc: stable@vger.kernel.org Suggested-by: Thomas Zimmermann <tzimmermann@suse.de> Fixes: 37c90d589dc0 ("drm/fb-helper: Fix single-probe color-format selection") Link: https://lore.kernel.org/dri-devel/20230102112927.26565-1-tzimmermann@suse.de/ Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20230515092943.1401558-1-linus.walleij@linaro.org
2023-05-16net: bcmgenet: Restore phy_stop() depending upon suspend/closeFlorian Fainelli
Removing the phy_stop() from bcmgenet_netif_stop() ended up causing warnings from the PHY library that phy_start() is called from the RUNNING state since we are no longer stopping the PHY state machine during bcmgenet_suspend(). Restore the call to phy_stop() but make it conditional on being called from the close or suspend path. Fixes: c96e731c93ff ("net: bcmgenet: connect and disconnect from the PHY state machine") Fixes: 93e0401e0fc0 ("net: bcmgenet: Remove phy_stop() from bcmgenet_netif_stop()") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Link: https://lore.kernel.org/r/20230515025608.2587012-1-f.fainelli@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2023-05-16spi: dw: Replace spi->chip_select references with function callsAmit Kumar Mahapatra
New set/get APIs for accessing spi->chip_select were introduced by 'commit 9e264f3f85a5 ("spi: Replace all spi->chip_select and spi->cs_gpiod references with function call")', but the 'commit 2c8606040a80 ("spi: dw: Add support for AMD Pensando Elba SoC")' uses the old interface by directly accessing spi->chip_select. So, replace all spi->chip_select references in the driver with new get/set APIs. Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com Acked-by: Serge Semin <fancer.lancer@gmail.com Link: https://lore.kernel.org/r/20230515130343.63770-1-amit.kumar-mahapatra@amd.com Signed-off-by: Mark Brown <broonie@kernel.org
2023-05-16regulator: Fix error checking for debugfs_create_dirOsama Muhammad
This patch fixes the error checking in core.c in debugfs_create_dir. The correct way to check if an error occurred is 'IS_ERR' inline function. Signed-off-by: Osama Muhammad <osmtendev@gmail.com Suggested-by: Ivan Orlov <ivan.orlov0322@gmail.com Link: https://lore.kernel.org/r/20230515172938.13338-1-osmtendev@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org
2023-05-16tpm/tpm_tis: Disable interrupts for more Lenovo devicesJerry Snitselaar
The P360 Tiny suffers from an irq storm issue like the T490s, so add an entry for it to tpm_tis_dmi_table, and force polling. There also previously was a report from the previous attempt to enable interrupts that involved a ThinkPad L490. So an entry is added for it as well. Cc: stable@vger.kernel.org Reported-by: Peter Zijlstra <peterz@infradead.org> # P360 Tiny Closes: https://lore.kernel.org/linux-integrity/20230505130731.GO83892@hirez.programming.kicks-ass.net/ Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
2023-05-16tpm: Prevent hwrng from activating during resumeJarkko Sakkinen
Set TPM_CHIP_FLAG_SUSPENDED in tpm_pm_suspend() and reset in tpm_pm_resume(). While the flag is set, tpm_hwrng() gives back zero bytes. This prevents hwrng from racing during resume. Cc: stable@vger.kernel.org Fixes: 6e592a065d51 ("tpm: Move Linux RNG connection to hwrng") Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
2023-05-16tpm_tis: Use tpm_chip_{start,stop} decoration inside tpm_tis_resumeJarkko Sakkinen
Before sending a TPM command, CLKRUN protocol must be disabled. This is not done in the case of tpm1_do_selftest() call site inside tpm_tis_resume(). Address this by decorating the calls with tpm_chip_{start,stop}, which should be always used to arm and disarm the TPM chip for transmission. Finally, move the call to the main TPM driver callback as the last step because it should arm the chip by itself, if it needs that type of functionality. Cc: stable@vger.kernel.org Reported-by: Jason A. Donenfeld <Jason@zx2c4.com> Closes: https://lore.kernel.org/linux-integrity/CS68AWILHXS4.3M36M1EKZLUMS@suppilovahvero/ Fixes: a3fbfae82b4c ("tpm: take TPM chip power gating out of tpm_transmit()") Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
2023-05-16power: supply: mt6360: add a check of devm_work_autocancel in ↵Kang Chen
mt6360_charger_probe devm_work_autocancel may fail, add a check and return early. Fixes: 0402e8ebb8b86 ("power: supply: mt6360_charger: add MT6360 charger support") Signed-off-by: Kang Chen <void0red@gmail.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2023-05-16power: supply: sbs-charger: Fix INHIBITED bit for Status regDaisuke Nojiri
CHARGE_INHIBITED bit position of the ChargerStatus register is actually 0 not 1. This patch corrects it. Fixes: feb583e37f8a8 ("power: supply: add sbs-charger driver") Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2023-05-15Merge patch series "can: bxcan: add support for single peripheral configuration"Marc Kleine-Budde
Dario Binacchi <dario.binacchi@amarulasolutions.com> says: The series adds support for managing bxCAN controllers in single peripheral configuration. Unlike stm32f4 SOCs, where bxCAN controllers are only in dual peripheral configuration, stm32f7 SOCs contain three CAN peripherals, CAN1 and CAN2 in dual peripheral configuration and CAN3 in single peripheral configuration: - Dual CAN peripheral configuration: * CAN1: Primary bxCAN for managing the communication between a secondary bxCAN and the 512-byte SRAM memory. * CAN2: Secondary bxCAN with no direct access to the SRAM memory. This means that the two bxCAN cells share the 512-byte SRAM memory and CAN2 can't be used without enabling CAN1. - Single CAN peripheral configuration: * CAN3: Primary bxCAN with dedicated Memory Access Controller unit and 512-byte SRAM memory. The driver has been tested on the stm32f769i-discovery board with a kernel version 5.19.0-rc2 in loopback + silent mode: | ip link set can[0-2] type can bitrate 125000 loopback on listen-only on | ip link set up can[0-2] | candump can[0-2] -L & | cansend can[0-2] 300#AC.AB.AD.AE.75.49.AD.D1 Changes in v2: - s/fiter/filter/ in the commit message - Replace struct bxcan_mb::primary with struct bxcan_mb::cfg. - Move after the patch "can: bxcan: add support for single peripheral configuration". - Add node gcan3. - Rename gcan as gcan1. - Add property "st,can-secondary" to can2 node. - Drop patch "dt-bindings: mfd: stm32f7: add binding definition for CAN3" because it has been accepted. - Add patch "ARM: dts: stm32f429: put can2 in secondary mode". - Add patch "dt-bindings: net: can: add "st,can-secondary" property". v1: https://lore.kernel.org/all/20230423172528.1398158-1-dario.binacchi@amarulasolutions.com Link: https://lore.kernel.org/all/20230427204540.3126234-1-dario.binacchi@amarulasolutions.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2023-05-15ARM: dts: stm32: add CAN support on stm32f746Dario Binacchi
Add support for bxcan (Basic eXtended CAN controller) to STM32F746. The chip contains three CAN peripherals, CAN1 and CAN2 in dual peripheral configuration and CAN3 in single peripheral configuration: - Dual CAN peripheral configuration: * CAN1: Primary bxCAN for managing the communication between a secondary bxCAN and the 512-byte SRAM memory. * CAN2: Secondary bxCAN with no direct access to the SRAM memory. This means that the two bxCAN cells share the 512-byte SRAM memory and CAN2 can't be used without enabling CAN1. - Single CAN peripheral configuration: * CAN3: Primary bxCAN with dedicated Memory Access Controller unit and 512-byte SRAM memory. ------------------------------------------------------------------------- | features | CAN1 | CAN2 | CAN 3 | ------------------------------------------------------------------------- | SRAM | 512-byte shared between CAN1 & CAN2 | 512-byte | ------------------------------------------------------------------------- | Filters | 26 filters shared between CAN1 & CAN2 | 14 filters | ------------------------------------------------------------------------- Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com> Link: https://lore.kernel.org/all/20230427204540.3126234-6-dario.binacchi@amarulasolutions.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2023-05-15can: bxcan: add support for single peripheral configurationDario Binacchi
Add support for bxCAN controller in single peripheral configuration: - primary bxCAN - dedicated Memory Access Controller unit - 512-byte SRAM memory - 14 filter banks Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com> Link: https://lore.kernel.org/all/20230427204540.3126234-5-dario.binacchi@amarulasolutions.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2023-05-15ARM: dts: stm32: add pin map for CAN controller on stm32f7Dario Binacchi
Add pin configurations for using CAN controller on stm32f7. Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com> Link: https://lore.kernel.org/all/20230427204540.3126234-4-dario.binacchi@amarulasolutions.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2023-05-15ARM: dts: stm32f429: put can2 in secondary modeDario Binacchi
This is a preparation patch for the upcoming support to manage CAN peripherals in single configuration. The addition ensures backwards compatibility. Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com> Link: https://lore.kernel.org/all/20230427204540.3126234-3-dario.binacchi@amarulasolutions.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2023-05-15dt-bindings: net: can: add "st,can-secondary" propertyDario Binacchi
On the stm32f7 Socs the can peripheral can be in single or dual configuration. In the dual configuration, in turn, it can be in primary or secondary mode. The addition of the 'st,can-secondary' property allows you to specify this mode in the dual configuration. CAN peripheral nodes in single configuration contain neither "st,can-primary" nor "st,can-secondary". Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com> Reviewed-by: Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/all/20230427204540.3126234-2-dario.binacchi@amarulasolutions.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2023-05-15can: CAN_BXCAN should depend on ARCH_STM32Geert Uytterhoeven
The STMicroelectronics STM32 basic extended CAN Controller (bxCAN) is only present on STM32 SoCs. Hence drop the "|| OF" part from its dependency rule, to prevent asking the user about this driver when configuring a kernel without STM32 SoC support. Fixes: f00647d8127be4d3 ("can: bxcan: add support for ST bxCAN controller") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Simon Horman <simon.horman@corigine.com> Link: https://lore.kernel.org/all/40095112efd1b2214e4223109fd9f0c6d0158a2d.1680609318.git.geert+renesas@glider.be Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2023-05-15can: dev: fix missing CAN XL support in can_put_echo_skb()Oliver Hartkopp
can_put_echo_skb() checks for the enabled IFF_ECHO flag and the correct ETH_P type of the given skbuff. When implementing the CAN XL support the new check for ETH_P_CANXL has been forgotten. Fixes: fb08cba12b52 ("can: canxl: update CAN infrastructure for CAN XL frames") Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Link: https://lore.kernel.org/all/20230506184515.39241-1-socketcan@hartkopp.net Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2023-05-15can: j1939: recvmsg(): allow MSG_CMSG_COMPAT flagOliver Hartkopp
The control message provided by J1939 support MSG_CMSG_COMPAT but blocked recvmsg() syscalls that have set this flag, i.e. on 32bit user space on 64 bit kernels. Link: https://github.com/hartkopp/can-isotp/issues/59 Cc: Oleksij Rempel <o.rempel@pengutronix.de> Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> Acked-by: Oleksij Rempel <o.rempel@pengutronix.de> Fixes: 9d71dd0c7009 ("can: add support of SAE J1939 protocol") Link: https://lore.kernel.org/20230505110308.81087-3-mkl@pengutronix.de Cc: stable@vger.kernel.org Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2023-05-15can: isotp: recvmsg(): allow MSG_CMSG_COMPAT flagOliver Hartkopp
The control message provided by isotp support MSG_CMSG_COMPAT but blocked recvmsg() syscalls that have set this flag, i.e. on 32bit user space on 64 bit kernels. Link: https://github.com/hartkopp/can-isotp/issues/59 Cc: Oleksij Rempel <o.rempel@pengutronix.de> Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Fixes: 42bf50a1795a ("can: isotp: support MSG_TRUNC flag when reading from socket") Link: https://lore.kernel.org/20230505110308.81087-2-mkl@pengutronix.de Cc: stable@vger.kernel.org Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2023-05-15wifi: rtl8xxxu: fix authentication timeout due to incorrect RCR valueYun Lu
When using rtl8192cu with rtl8xxxu driver to connect wifi, there is a probability of failure, which shows "authentication with ... timed out". Through debugging, it was found that the RCR register has been inexplicably modified to an incorrect value, resulting in the nic not being able to receive authenticated frames. To fix this problem, add regrcr in rtl8xxxu_priv struct, and store the RCR value every time the register is written, and use it the next time the register need to be modified. Signed-off-by: Yun Lu <luyun@kylinos.cn> Link: https://lore.kernel.org/all/20230427020512.1221062-1-luyun_611@163.com Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20230512012055.2990472-1-luyun_611@163.com
2023-05-15wifi: brcmfmac: Check for probe() id argument being NULLHans de Goede
The probe() id argument may be NULL in 2 scenarios: 1. brcmf_pcie_pm_leave_D3() calling brcmf_pcie_probe() to reprobe the device. 2. If a user tries to manually bind the driver from sysfs then the sdio / pcie / usb probe() function gets called with NULL as id argument. 1. Is being hit by users causing the following oops on resume and causing wifi to stop working: BUG: kernel NULL pointer dereference, address: 0000000000000018 <snip> Hardware name: Dell Inc. XPS 13 9350/0PWNCR, BIDS 1.13.0 02/10/2020 Workgueue: events_unbound async_run_entry_fn RIP: 0010:brcmf_pcie_probe+Ox16b/0x7a0 [brcmfmac] <snip> Call Trace: <TASK> brcmf_pcie_pm_leave_D3+0xc5/8x1a0 [brcmfmac be3b4cefca451e190fa35be8f00db1bbec293887] ? pci_pm_resume+0x5b/0xf0 ? pci_legacy_resume+0x80/0x80 dpm_run_callback+0x47/0x150 device_resume+0xa2/0x1f0 async_resume+0x1d/0x30 <snip> Fix this by checking for id being NULL. In the PCI and USB cases try a manual lookup of the id so that manually binding the driver through sysfs and more importantly brcmf_pcie_probe() on resume will work. For the SDIO case there is no helper to do a manual sdio_device_id lookup, so just directly error out on a NULL id there. Fixes: da6d9c8ecd00 ("wifi: brcmfmac: add firmware vendor info in driver info") Reported-by: Felix <nimrod4garoa@gmail.com> Link: https://lore.kernel.org/regressions/4ef3f252ff530cbfa336f5a0d80710020fc5cb1e.camel@gmail.com/ Cc: stable@vger.kernel.org Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20230510141856.46532-1-hdegoede@redhat.com
2023-05-15wifi: rtw88: correct qsel_to_ep[] type as intPing-Ke Shih
qsel_to_ep[] can be assigned negative value, so change type from 'u8' to 'int'. Otherwise, Smatch static checker warns: drivers/net/wireless/realtek/rtw88/usb.c:219 rtw_usb_parse() warn: assigning (-22) to unsigned variable 'rtwusb->qsel_to_ep[8]' Cc: stable@vger.kernel.org Fixes: a6f187f92bcc ("wifi: rtw88: usb: fix priority queue to endpoint mapping") Reported-by: Dan Carpenter <dan.carpenter@linaro.org> Link: https://lore.kernel.org/linux-wireless/c3f70197-829d-48ed-ae15-66a9de80fa90@kili.mountain/ Cc: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Tested-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20230508085539.46795-1-pkshih@realtek.com
2023-05-15cpufreq: ACPI: Prevent a warning when another frequency driver is loadedPetr Pavlu
The recent change to use platform devices to load ACPI PPC and PCC drivers caused that a misleading warning is reported when a respective module cannot be loaded because another CPU frequency driver is already registered: kernel: acpi-cpufreq: probe of acpi-cpufreq failed with error -17 Address it by changing the return code in acpi-cpufreq and pcc-cpufreq for this case from -EEXIST to -ENODEV which silences the warning in call_driver_probe(). The change has also a benefit for users of init_module() as this return code is propagated out from the syscall. The previous -EEXIST code made the callers, such as kmod, wrongly believe that the module was already loaded instead of that it failed to load. Fixes: 691a63712347 ("ACPI: cpufreq: Use platform devices to load ACPI PPC and PCC drivers") Reported-by: Kevin Locke <kevin@kevinlocke.name> Link: https://lore.kernel.org/lkml/ZFreh8SDMX67EaB6@kevinlocke.name/ Signed-off-by: Petr Pavlu <petr.pavlu@suse.com> Tested-by: Kevin Locke <kevin@kevinlocke.name> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2023-05-16ASoC: SOF: Intel: hda-mlink: fixes and extensionsMark Brown
Merge series from Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>: With additional testing with multiple links and multiple DAI types, we found a couple of mistakes with refcounts, base address, missing initialization. A new helper was also added due to a change in the SoundWire programming sequences, with the host driver in charge of setting up the DMA channel mapping instead of the firmware.
2023-05-15bpf: netdev: init the offload table earlierJakub Kicinski
Some netdevices may get unregistered before late_initcall(), we have to move the hashtable init earlier. Fixes: f1fc43d03946 ("bpf: Move offload initialization into late_initcall") Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217399 Signed-off-by: Jakub Kicinski <kuba@kernel.org> Acked-by: Stanislav Fomichev <sdf@google.com> Link: https://lore.kernel.org/r/20230505215836.491485-1-kuba@kernel.org Signed-off-by: Alexei Starovoitov <ast@kernel.org>
2023-05-15platform/mellanox: mlxbf-pmc: fix sscanf() error checkingDan Carpenter
The sscanf() function never returns negatives. It returns the number of items successfully read. Fixes: 1a218d312e65 ("platform/mellanox: mlxbf-pmc: Add Mellanox BlueField PMC driver") Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Link: https://lore.kernel.org/r/4ccdfd28-099b-40bf-8d77-ad4ea2e76b93@kili.mountain Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2023-05-15platform/x86/amd/pmf: Fix CnQF and auto-mode after resumeMario Limonciello
After suspend/resume cycle there is an error message and auto-mode or CnQF stops working. [ 5741.447511] amd-pmf AMDI0100:00: SMU cmd failed. err: 0xff [ 5741.447523] amd-pmf AMDI0100:00: AMD_PMF_REGISTER_RESPONSE:ff [ 5741.447527] amd-pmf AMDI0100:00: AMD_PMF_REGISTER_ARGUMENT:7 [ 5741.447531] amd-pmf AMDI0100:00: AMD_PMF_REGISTER_MESSAGE:16 [ 5741.447540] amd-pmf AMDI0100:00: [AUTO_MODE] avg power: 0 mW mode: QUIET This is because the DRAM address used for accessing metrics table needs to be refreshed after a suspend resume cycle. Add a resume callback to reset this again. Fixes: 1a409b35c995 ("platform/x86/amd/pmf: Get performance metrics from PMFW") Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Link: https://lore.kernel.org/r/20230513011408.958-1-mario.limonciello@amd.com Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2023-05-15platform/x86: asus-wmi: Ignore WMI events with codes 0x7B, 0xC0Alexandru Sorodoc
On ASUS GU604V the key 0x7B is issued when the charger is connected or disconnected, and key 0xC0 is issued when an external display is connected or disconnected. This commit maps them to KE_IGNORE to slience kernel messages about unknown keys, such as: kernel: asus_wmi: Unknown key code 0x7b Signed-off-by: Alexandru Sorodoc <ealex95@gmail.com> Link: https://lore.kernel.org/r/20230512101517.47416-1-ealex95@gmail.com Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2023-05-15powerpc/crypto: Fix aes-gcm-p10 build when VSX=nMichael Ellerman
When VSX is disabled, eg. microwatt_defconfig, the build fails with: In function ‘enable_kernel_vsx’, inlined from ‘vsx_begin’ at arch/powerpc/crypto/aes-gcm-p10-glue.c:68:2, inlined from ‘p10_aes_gcm_crypt.constprop’ at arch/powerpc/crypto/aes-gcm-p10-glue.c:244:2: ... arch/powerpc/include/asm/switch_to.h:86:9: note: in expansion of macro ‘BUILD_BUG’ 86 | BUILD_BUG(); | ^~~~~~~~~ Fix it by making the p10-aes-gcm code depend on VSX. Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://msgid.link/20230515124731.122962-1-mpe%40ellerman.id.au
2023-05-15ACPI: resource: Add IRQ override quirk for LG UltraPC 17U70PRubén Gómez
Add an ACPI IRQ override quirk for LG UltraPC 17U70P to address the internal keyboard problem on it. Link: https://bugzilla.kernel.org/show_bug.cgi?id=213031 Link: https://bugzilla.kernel.org/show_bug.cgi?id=216983 Signed-off-by: Rubén Gómez Agudo <mrgommer@proton.me> [ rjw: Subject, changelog, white space damage fixes ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2023-05-15s390/ipl: fix IPIB virtual vs physical address confusionAlexander Gordeev
The pointer to IPL Parameter Information Block is stored in the absolute lowcore for later use by dump tools. That pointer is a virtual address, though it should be physical instead. Note, this does not fix a real issue, since virtual and physical addresses are currently the same. Suggested-by: Heiko Carstens <hca@linux.ibm.com> Reviewed-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
2023-05-15s390/topology: honour nr_cpu_ids when adding CPUsAlexander Gordeev
When SMT thread CPUs are added to CPU masks the nr_cpu_ids limit is not checked and could be exceeded. This leads to a warning for example if CONFIG_DEBUG_PER_CPU_MAPS is set and the command line parameter nr_cpus is set to 1. Reviewed-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
2023-05-15s390/cio: include subchannels without devices also for evaluationVineeth Vijayan
Currently when the new channel-path is enabled, we do evaluation only on the subchannels with a device connected on it. This is because, in the past, if the device in the subchannel is not working or not available, we used to unregister the subchannels. But, from the 'commit 2297791c92d0 ("s390/cio: dont unregister subchannel from child-drivers")' we allow subchannels with or without an active device connected on it. So, when we do the io_subchannel_verify, make sure that, we are evaluating the subchannels without any device too. Fixes: 2297791c92d0 ("s390/cio: dont unregister subchannel from child-drivers") Reported-by: Boris Fiuczynski <fiuczy@linux.ibm.com> Signed-off-by: Vineeth Vijayan <vneethv@linux.ibm.com> Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com> Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
2023-05-15s390/defconfigs: set CONFIG_INIT_STACK_NONE=yHeiko Carstens
Set CONFIG_INIT_STACK_NONE=y in defconfigs to avoid the extra overhead of initializing all stack variables by default. Users who want to have that must change the configuration on their own. Signed-off-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
2023-05-15s390/pkey: zeroize key blobsHolger Dengler
Key blobs for the IOCTLs PKEY_KBLOB2PROTK[23] may contain clear key material. Zeroize the copies of these keys in kernel memory after creating the protected key. Reviewed-by: Harald Freudenberger <freude@linux.ibm.com> Signed-off-by: Holger Dengler <dengler@linux.ibm.com> Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
2023-05-15s390/crypto: use vector instructions only if available for ChaCha20Heiko Carstens
Commit 349d03ffd5f6 ("crypto: s390 - add crypto library interface for ChaCha20") added a library interface to the s390 specific ChaCha20 implementation. However no check was added to verify if the required facilities are installed before branching into the assembler code. If compiled into the kernel, this will lead to the following crash, if vector instructions are not available: data exception: 0007 ilc:3 [#1] SMP Modules linked in: CPU: 0 PID: 1 Comm: swapper/0 Not tainted 6.3.0-rc7+ #11 Hardware name: IBM 3931 A01 704 (KVM/Linux) Krnl PSW : 0704e00180000000 000000001857277a (chacha20_vx+0x32/0x818) R:0 T:1 IO:1 EX:1 Key:0 M:1 W:0 P:0 AS:3 CC:2 PM:0 RI:0 EA:3 Krnl GPRS: 0000037f0000000a ffffffffffffff60 000000008184b000 0000000019f5c8e6 0000000000000109 0000037fffb13c58 0000037fffb13c78 0000000019bb1780 0000037fffb13c58 0000000019f5c8e6 000000008184b000 0000000000000109 00000000802d8000 0000000000000109 0000000018571ebc 0000037fffb13718 Krnl Code: 000000001857276a: c07000b1f80b larl %r7,0000000019bb1780 0000000018572770: a708000a lhi %r0,10 #0000000018572774: e78950000c36 vlm %v24,%v25,0(%r5),0 >000000001857277a: e7a060000806 vl %v26,0(%r6),0 0000000018572780: e7bf70004c36 vlm %v27,%v31,0(%r7),4 0000000018572786: e70b00000456 vlr %v0,%v27 000000001857278c: e71800000456 vlr %v1,%v24 0000000018572792: e74b00000456 vlr %v4,%v27 Call Trace: [<000000001857277a>] chacha20_vx+0x32/0x818 Last Breaking-Event-Address: [<0000000018571eb6>] chacha20_crypt_s390.constprop.0+0x6e/0xd8 ---[ end trace 0000000000000000 ]--- Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b Fix this by adding a missing MACHINE_HAS_VX check. Fixes: 349d03ffd5f6 ("crypto: s390 - add crypto library interface for ChaCha20") Reported-by: Marc Hartmayer <mhartmay@linux.ibm.com> Cc: <stable@vger.kernel.org> # 5.19+ Reviewed-by: Harald Freudenberger <freude@linux.ibm.com> [agordeev@linux.ibm.com: remove duplicates in commit message] Signed-off-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
2023-05-15NFSD: Remove open coding of string copyAzeem Shaikh
Instead of open coding a __dynamic_array(), use the __string() and __assign_str() helper macros that exist for this kind of use case. Part of an effort to remove deprecated strlcpy() [1] completely from the kernel[2]. [1] https://www.kernel.org/doc/html/latest/process/deprecated.html#strlcpy [2] https://github.com/KSPP/linux/issues/89 Fixes: 3c92fba557c6 ("NFSD: Enhance the nfsd_cb_setup tracepoint") Signed-off-by: Azeem Shaikh <azeemshaikh38@gmail.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
2023-05-15ASoC: SOF: topology: Fix tuples array allocationRanjani Sridharan
The memory allocated for the tuples array assumes that there's 1 instance of all tokens already. So for those tokens that have multiple instances in topology, we need to exclude the initial instance that has already been accounted for. Fixes: 4fdef47a44d6 ("ASoC: SOF: ipc4-topology: Add new tokens for input/output pin format count") Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com Link: https://lore.kernel.org/r/20230515085200.17094-1-peter.ujfalusi@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org
2023-05-15ASoC: SOF: Separate the tokens for input and output pin indexRanjani Sridharan
Using the same token ID for both input and output format pin index results in collisions and incorrect pin index getting parsed from topology. Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com Reviewed-by: Paul Olaru <paul.olaru@oss.nxp.com Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com Link: https://lore.kernel.org/r/20230515104403.32207-1-peter.ujfalusi@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org
2023-05-15ASoC: SOF: Various runtime pm fixes, improvementsMark Brown
Merge series from Peter Ujfalusi <peter.ujfalusi@linux.intel.com>: Three patch to correct error path PM runtime handling in few places. Regards, Peter --- Pierre-Louis Bossart (3): ASoC: SOF: debug: conditionally bump runtime_pm counter on exceptions ASoC: SOF: pcm: fix pm_runtime imbalance in error handling ASoC: SOF: sof-client-probes: fix pm_runtime imbalance in error handling sound/soc/sof/debug.c | 4 ++-- sound/soc/sof/pcm.c | 11 ++++++----- sound/soc/sof/sof-client-probes.c | 14 ++++++++------ 3 files changed, 16 insertions(+), 13 deletions(-) -- 2.40.1
2023-05-15net: phylink: fix ksettings_set() ethtool callRussell King (Oracle)
While testing a Fiberstore SFP-10G-T module (which uses 10GBASE-R with rate adaption) in a Clearfog platform (which can't do that) it was found that the PHYs advertisement was not limited according to the hosts capabilities when using ethtool to change it. Fix this by ensuring that we mask the advertisement with the computed support mask as the very first thing we do. Fixes: cbc1bb1e4689 ("net: phylink: simplify phy case for ksettings_set method") Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit (git 2.34.1) at 2025-09-12 11:56:14 +0000