| Age | Commit message (Collapse) | Author |
|---|
|
This email address will not be available in a few days.
Update my own email address to xiang@kernel.org, which
should be available all the time.
Link: https://lore.kernel.org/r/20200328040036.117974-1-gaoxiang25@huawei.com
Acked-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Gao Xiang <gaoxiang25@huawei.com>
|
|
The interrupt is not required so use platform_irq_get_optional() to
avoid error messages like
i2c-pca-platform 22080000.i2c: IRQ index 0 not found
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Fix a missing struct parameter description to allow
warning free W=1 compilation.
Signed-off-by: Alain Volmat <avolmat@me.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Only one user left; the thing had been made polymorphic back in 2013
for the sake of MPX. No point keeping it now that MPX is gone.
Convert futex_atomic_cmpxchg_inatomic() to user_access_{begin,end}()
while we are at it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
uses get_user() and put_user() for memory accesses
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
lock cmpxchg leaves the current value in eax; no need to reload it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
user_access_begin/user_access_end()
Lift stac/clac pairs from __futex_atomic_op{1,2} into arch_futex_atomic_op_inuser(),
fold them with access_ok() in there. The switch in arch_futex_atomic_op_inuser()
is what has required the previous (objtool) commit...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
it's not really different from e.g. __sanitizer_cov_trace_cmp4();
as it is, the switches that generate an array of labels get
rejected by objtool, while slightly different set of cases
that gets compiled into a series of comparisons is accepted.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
access_ok() is always true on those
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
everything it uses is doing access_ok() already
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Move access_ok() in and pagefault_enable()/pagefault_disable() out.
Mechanical conversion only - some instances don't really need
a separate access_ok() at all (e.g. the ones only using
get_user()/put_user(), or architectures where access_ok()
is always true); we'll deal with that in followups.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Daniel Borkmann says:
====================
This adds various straight-forward helper improvements and additions to BPF
cgroup based connect(), sendmsg(), recvmsg() and bind-related hooks which
would allow to implement more fine-grained policies and improve current load
balancer limitations we're seeing. For details please see individual patches.
I've tested them on Kubernetes & Cilium and also added selftests for the small
verifier extension. Thanks!
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Add various tests to make sure the verifier keeps catching them:
# ./test_verifier
[...]
#230/p pass ctx or null check, 1: ctx OK
#231/p pass ctx or null check, 2: null OK
#232/p pass ctx or null check, 3: 1 OK
#233/p pass ctx or null check, 4: ctx - const OK
#234/p pass ctx or null check, 5: null (connect) OK
#235/p pass ctx or null check, 6: null (bind) OK
#236/p pass ctx or null check, 7: ctx (bind) OK
#237/p pass ctx or null check, 8: null (bind) OK
[...]
Summary: 1595 PASSED, 0 SKIPPED, 0 FAILED
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/c74758d07b1b678036465ef7f068a49e9efd3548.1585323121.git.daniel@iogearbox.net
|
|
We already have the bpf_get_current_uid_gid() helper enabled, and
given we now have perf event RB output available for connect(),
sendmsg(), recvmsg() and bind-related hooks, add a trivial change
to enable bpf_get_current_pid_tgid() and bpf_get_current_comm()
as well.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/18744744ed93c06343be8b41edcfd858706f39d7.1585323121.git.daniel@iogearbox.net
|
|
Enable the bpf_get_current_cgroup_id() helper for connect(), sendmsg(),
recvmsg() and bind-related hooks in order to retrieve the cgroup v2
context which can then be used as part of the key for BPF map lookups,
for example. Given these hooks operate in process context 'current' is
always valid and pointing to the app that is performing mentioned
syscalls if it's subject to a v2 cgroup. Also with same motivation of
commit 7723628101aa ("bpf: Introduce bpf_skb_ancestor_cgroup_id helper")
enable retrieval of ancestor from current so the cgroup id can be used
for policy lookups which can then forbid connect() / bind(), for example.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/d2a7ef42530ad299e3cbb245e6c12374b72145ef.1585323121.git.daniel@iogearbox.net
|
|
Today, Kubernetes is still operating on cgroups v1, however, it is
possible to retrieve the task's classid based on 'current' out of
connect(), sendmsg(), recvmsg() and bind-related hooks for orchestrators
which attach to the root cgroup v2 hook in a mixed env like in case
of Cilium, for example, in order to then correlate certain pod traffic
and use it as part of the key for BPF map lookups.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/555e1c69db7376c0947007b4951c260e1074efc3.1585323121.git.daniel@iogearbox.net
|
|
In Cilium we're mainly using BPF cgroup hooks today in order to implement
kube-proxy free Kubernetes service translation for ClusterIP, NodePort (*),
ExternalIP, and LoadBalancer as well as HostPort mapping [0] for all traffic
between Cilium managed nodes. While this works in its current shape and avoids
packet-level NAT for inter Cilium managed node traffic, there is one major
limitation we're facing today, that is, lack of netns awareness.
In Kubernetes, the concept of Pods (which hold one or multiple containers)
has been built around network namespaces, so while we can use the global scope
of attaching to root BPF cgroup hooks also to our advantage (e.g. for exposing
NodePort ports on loopback addresses), we also have the need to differentiate
between initial network namespaces and non-initial one. For example, ExternalIP
services mandate that non-local service IPs are not to be translated from the
host (initial) network namespace as one example. Right now, we have an ugly
work-around in place where non-local service IPs for ExternalIP services are
not xlated from connect() and friends BPF hooks but instead via less efficient
packet-level NAT on the veth tc ingress hook for Pod traffic.
On top of determining whether we're in initial or non-initial network namespace
we also have a need for a socket-cookie like mechanism for network namespaces
scope. Socket cookies have the nice property that they can be combined as part
of the key structure e.g. for BPF LRU maps without having to worry that the
cookie could be recycled. We are planning to use this for our sessionAffinity
implementation for services. Therefore, add a new bpf_get_netns_cookie() helper
which would resolve both use cases at once: bpf_get_netns_cookie(NULL) would
provide the cookie for the initial network namespace while passing the context
instead of NULL would provide the cookie from the application's network namespace.
We're using a hole, so no size increase; the assignment happens only once.
Therefore this allows for a comparison on initial namespace as well as regular
cookie usage as we have today with socket cookies. We could later on enable
this helper for other program types as well as we would see need.
(*) Both externalTrafficPolicy={Local|Cluster} types
[0] https://github.com/cilium/cilium/blob/master/bpf/bpf_sock.c
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/c47d2346982693a9cf9da0e12690453aded4c788.1585323121.git.daniel@iogearbox.net
|
|
Currently, connect(), sendmsg(), recvmsg() and bind-related hooks
are all lacking perf event rb output in order to push notifications
or monitoring events up to user space. Back in commit a5a3a828cd00
("bpf: add perf event notificaton support for sock_ops"), I've worked
with Sowmini to enable them for sock_ops where the context part is
not used (as opposed to skbs for example where the packet data can
be appended). Make the bpf_sockopt_event_output() helper generic and
enable it for mentioned hooks.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/69c39daf87e076b31e52473c902e9bfd37559124.1585323121.git.daniel@iogearbox.net
|
|
We currently make heavy use of the socket cookie in BPF's connect(),
sendmsg() and recvmsg() hooks for load-balancing decisions. However,
it is currently not enabled/implemented in BPF {post-}bind hooks
where it can later be used in combination for correlation in the tc
egress path, for example.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/e9d71f310715332f12d238cc650c1edc5be55119.1585323121.git.daniel@iogearbox.net
|
|
Daniel Borkmann says:
====================
pull-request: bpf 2020-03-27
The following pull-request contains BPF updates for your *net* tree.
We've added 3 non-merge commits during the last 4 day(s) which contain
a total of 4 files changed, 25 insertions(+), 20 deletions(-).
The main changes are:
1) Explicitly memset the bpf_attr structure on bpf() syscall to avoid
having to rely on compiler to do so. Issues have been noticed on
some compilers with padding and other oddities where the request was
then unexpectedly rejected, from Greg Kroah-Hartman.
2) Sanitize the bpf_struct_ops TCP congestion control name in order to
avoid problematic characters such as whitespaces, from Martin KaFai Lau.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Vladimir Oltean says:
====================
Configure the MTU on DSA switches
This series adds support for configuring the MTU on front-panel switch
ports, while seamlessly adapting the CPU port and the DSA master to the
largest value plus the tagger overhead.
It also implements bridge MTU auto-normalization within the DSA core, as
resulted after the feedback of the implementation of this feature inside
the bridge driver in v2.
Support was added for quite a number of switches, in the hope that this
series would gain some traction:
- sja1105
- felix
- vsc73xx
- b53 and rest of the platform
V3 of this series was submitted here:
https://patchwork.ozlabs.org/cover/1262394/
V2 of this series was submitted here:
https://patchwork.ozlabs.org/cover/1261471/
V1 of this series was submitted here:
https://patchwork.ozlabs.org/cover/1199868/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Changing the MTU for this switch means altering the
DEV_GMII:MAC_CFG_STATUS:MAC_MAXLEN_CFG field MAX_LEN, which in turn
limits the size of frames that can be received.
Special accounting needs to be done for the DSA CPU port (NPI port in
hardware terms). The NPI port configuration needs to be held inside the
private ocelot structure, since it is now accessed from multiple places.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of hardcoding the MTU to the maximum value allowed by the
hardware, obey the value known by the operating system.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On this switch, the frame length enforcements are performed by the
ingress policers. There are 2 types of those: regular L2 (also called
best-effort) and Virtual Link policers (an ARINC664/AFDX concept for
defining L2 streams with certain QoS abilities). To avoid future
confusion, I prefer to call the reset reason "Best-effort policers",
even though the VL policers are not yet supported.
We also need to change the setup of the initial static config, such that
DSA calls to .change_mtu (which are expensive) become no-ops and don't
reset the switch 5 times.
A driver-level decision is to unconditionally allow single VLAN-tagged
traffic on all ports. The CPU port must accept an additional VLAN header
for the DSA tag, which is again a driver-level decision.
The policers actually count bytes not only from the SDU, but also from
the Ethernet header and FCS, so those need to be accounted for as well.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It looks like the Broadcom switches supported by the b53 driver don't
support precise configuration of the MTU, but just a mumbo-jumbo boolean
flag. Set that.
Also configure BCM583XX devices to send and receive jumbo frames when
ports are configured with 10/100 Mbps speed.
Signed-off-by: Murali Krishna Policharla <murali.policharla@broadcom.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Many switches don't have an explicit knob for configuring the MTU
(maximum transmission unit per interface). Instead, they do the
length-based packet admission checks on the ingress interface, for
reasons that are easy to understand (why would you accept a packet in
the queuing subsystem if you know you're going to drop it anyway).
So it is actually the MRU that these switches permit configuring.
In Linux there only exists the IFLA_MTU netlink attribute and the
associated dev_set_mtu function. The comments like to play blind and say
that it's changing the "maximum transfer unit", which is to say that
there isn't any directionality in the meaning of the MTU word. So that
is the interpretation that this patch is giving to things: MTU == MRU.
When 2 interfaces having different MTUs are bridged, the bridge driver
MTU auto-adjustment logic kicks in: what br_mtu_auto_adjust() does is it
adjusts the MTU of the bridge net device itself (and not that of the
slave net devices) to the minimum value of all slave interfaces, in
order for forwarded packets to not exceed the MTU regardless of the
interface they are received and send on.
The idea behind this behavior, and why the slave MTUs are not adjusted,
is that normal termination from Linux over the L2 forwarding domain
should happen over the bridge net device, which _is_ properly limited by
the minimum MTU. And termination over individual slave devices is
possible even if those are bridged. But that is not "forwarding", so
there's no reason to do normalization there, since only a single
interface sees that packet.
The problem with those switches that can only control the MRU is with
the offloaded data path, where a packet received on an interface with
MRU 9000 would still be forwarded to an interface with MRU 1500. And the
br_mtu_auto_adjust() function does not really help, since the MTU
configured on the bridge net device is ignored.
In order to enforce the de-facto MTU == MRU rule for these switches, we
need to do MTU normalization, which means: in order for no packet larger
than the MTU configured on this port to be sent, then we need to limit
the MRU on all ports that this packet could possibly come from. AKA
since we are configuring the MRU via MTU, it means that all ports within
a bridge forwarding domain should have the same MTU.
And that is exactly what this patch is trying to do.
>From an implementation perspective, we try to follow the intent of the
user, otherwise there is a risk that we might livelock them (they try to
change the MTU on an already-bridged interface, but we just keep
changing it back in an attempt to keep the MTU normalized). So the MTU
that the bridge is normalized to is either:
- The most recently changed one:
ip link set dev swp0 master br0
ip link set dev swp1 master br0
ip link set dev swp0 mtu 1400
This sequence will make swp1 inherit MTU 1400 from swp0.
- The one of the most recently added interface to the bridge:
ip link set dev swp0 master br0
ip link set dev swp1 mtu 1400
ip link set dev swp1 master br0
The above sequence will make swp0 inherit MTU 1400 as well.
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is useful be able to configure port policers on a switch to accept
frames of various sizes:
- Increase the MTU for better throughput from the default of 1500 if it
is known that there is no 10/100 Mbps device in the network.
- Decrease the MTU to limit the latency of high-priority frames under
congestion, or work around various network segments that add extra
headers to packets which can't be fragmented.
For DSA slave ports, this is mostly a pass-through callback, called
through the regular ndo ops and at probe time (to ensure consistency
across all supported switches).
The CPU port is called with an MTU equal to the largest configured MTU
of the slave ports. The assumption is that the user might want to
sustain a bidirectional conversation with a partner over any switch
port.
The DSA master is configured the same as the CPU port, plus the tagger
overhead. Since the MTU is by definition L2 payload (sans Ethernet
header), it is up to each individual driver to figure out if it needs to
do anything special for its frame tags on the CPU port (it shouldn't
except in special cases). So the MTU does not contain the tagger
overhead on the CPU port.
However the MTU of the DSA master, minus the tagger overhead, is used as
a proxy for the MTU of the CPU port, which does not have a net device.
This is to avoid uselessly calling the .change_mtu function on the CPU
port when nothing should change.
So it is safe to assume that the DSA master and the CPU port MTUs are
apart by exactly the tagger's overhead in bytes.
Some changes were made around dsa_master_set_mtu(), function which was
now removed, for 2 reasons:
- dev_set_mtu() already calls dev_validate_mtu(), so it's redundant to
do the same thing in DSA
- __dev_set_mtu() returns 0 if ops->ndo_change_mtu is an absent method
That is to say, there's no need for this function in DSA, we can safely
call dev_set_mtu() directly, take the rtnl lock when necessary, and just
propagate whatever errors get reported (since the user probably wants to
be informed).
Some inspiration (mainly in the MTU DSA notifier) was taken from a
vaguely similar patch from Murali and Florian, who are credited as
co-developers down below.
Co-developed-by: Murali Krishna Policharla <murali.policharla@broadcom.com>
Signed-off-by: Murali Krishna Policharla <murali.policharla@broadcom.com>
Co-developed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change DMA descriptor length to handle jumbo frames beyond 8192 bytes.
Also update jumbo frame max size to include FCS, the DMA packet length
received includes FCS.
Signed-off-by: Murali Krishna Policharla <murali.policharla@broadcom.com>
Reviewed-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The BCM7XX PHY family requires special configuration to pass jumbo
frames. Do that during initial PHY setup.
Signed-off-by: Murali Krishna Policharla <murali.policharla@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On Android/x86 the module loading infrastructure can't deal with
softdeps. Therefore the check for presence of the Realtek PHY driver
module fails. mdiobus_register() will try to load the PHY driver
module, therefore move the check to after this call and explicitly
check that a dedicated PHY driver is bound to the PHY device.
Fixes: f32593773549 ("r8169: check that Realtek PHY driver module is loaded")
Reported-by: Chih-Wei Huang <cwhuang@android-x86.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.7
Third set of patches for v5.7. Nothing really special this time,
business as usual.
When pulling this to net-next there's again a conflict in:
drivers/net/wireless/intel/iwlwifi/pcie/drv.c
To solve this drop these three lines from the conflict (the first hunk
from "HEAD") as the whole AX200 block was moved above in the same
file:
IWL_DEV_INFO(0x2723, 0x1653, iwl_ax200_cfg_cc, iwl_ax200_killer_1650w_name),
IWL_DEV_INFO(0x2723, 0x1654, iwl_ax200_cfg_cc, iwl_ax200_killer_1650x_name),
IWL_DEV_INFO(0x2723, IWL_CFG_ANY, iwl_ax200_cfg_cc, iwl_ax200_name),
And keep all the __IWL_DEV_INFO() entries (the second hunk). In other
words, take everything from wireless-drivers-next. When running 'git
diff' after the resolution the output should be empty.
Major changes:
brcmfmac
* add USB autosuspend support
ath11k
* handle RX fragments
* enable PN offload
* add support for HE BSS color
iwlwifi
* support new FW API version
* support for EDCA measurements
* new scan API features
* enable new firmware debugging code
====================
Kalle gave me directions on how to resolve the iwlwifi conflict
as follows:
====================
When pulling this to net-next there's again a conflict in:
drivers/net/wireless/intel/iwlwifi/pcie/drv.c
To solve this drop these three lines from the conflict (the first hunk
from "HEAD") as the whole AX200 block was moved above in the same
file:
IWL_DEV_INFO(0x2723, 0x1653, iwl_ax200_cfg_cc, iwl_ax200_killer_1650w_name),
IWL_DEV_INFO(0x2723, 0x1654, iwl_ax200_cfg_cc, iwl_ax200_killer_1650x_name),
IWL_DEV_INFO(0x2723, IWL_CFG_ANY, iwl_ax200_cfg_cc, iwl_ax200_name),
And keep all the __IWL_DEV_INFO() entries (the second hunk). In other
words, take everything from wireless-drivers-next. When running 'git
diff' after the resolution the output should be empty.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Julian Wiedmann says:
====================
s390/qeth: updates 2020-03-27
please apply the following patch series for qeth to netdev's net-next
tree.
Spring clean edition:
- remove one sysfs attribute that was never put in use,
- make support for OSN and OSX devices optional, and
- probe for removal of the obsolete OSN support.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
OSN devices currently spend an awful long time in qeth_l2_set_online()
until various unsupported HW cmds time out. This has been broken for
over two years, ever since
commit d22ffb5a712f ("s390/qeth: fix IPA command submission race")
triggered a FW bug in cmd processing.
Prior to commit 782e4a792147 ("s390/qeth: don't poll for cmd IO completion"),
this wait for timeout would have even been spent busy-polling.
The offending patch was picked up by stable and all relevant distros,
and yet noone noticed.
OSN setups only ever worked in combination with an out-of-tree blob, and
the last machine that even offered HW with OSN support was released back
in 2015.
Rather than attempting to work-around this FW issue for no actual gain,
add a deprecation warning so anyone who still wants to maintain this
part of the code can speak up. Else rip it all out in 2021.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The last machine generation that supports OSN is z13, and OSX is only
supported up to z14. Allow users and distros to decide whether they
still need support for these device types.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ever since commit 4a71df50047f ("qeth: new qeth device driver") introduced
this attribute, it can be read & written but has no actual effect.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Vasundhara Volam says:
====================
bnxt_en: Updates to devlink info_get cb
This series adds support for a generic macro to devlink info_get cb.
Adds support for fw.mgmt.api and board.id info to bnxt_en driver info_get
cb. Also, updates the devlink-info.rst and bnxt.rst documentation
accordingly.
This series adds a patch to fix few macro names that maps to bnxt_en
firmware versions.
v1->v2: Remove ECN dev param, base_mh_addr and serial number info support
in this series.
Rename drv.spec macro to fw.api.
---
v2->v3: Remove hw.addr info as it is per netdev but not per device info.
---
v3->v4: Rename "fw.api" to "fw.mgmt.api".
Also, add a patch that modifies few macro names in info_get command,
to match the devlink documentation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix macro names to report fw.mgmt and fw.ncsi versions to match the
devlink documentation.
Example display after fixes:
$ devlink dev info pci/0000:af:00.0
pci/0000:af:00.0:
driver bnxt_en
serial_number B0-26-28-FF-FE-25-84-20
versions:
fixed:
board.id BCM957454A4540
asic.id C454
asic.rev 1
running:
fw 216.1.154.0
fw.psid 0.0.0
fw.mgmt 216.1.146.0
fw.mgmt.api 1.10.1
fw.ncsi 864.0.44.0
fw.roce 216.1.16.0
Fixes: 9599e036b161 ("bnxt_en: Add support for devlink info command")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add part number info from the vital product data to info_get command
via devlink tool. Update bnxt.rst documentation as well.
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Store the part number and serial number information from VPD in
the bnxt structure. Follow up patch will add the support to display
the information via devlink command.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds a new macro for serial number keyword.
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Display the minimum version of firmware interface spec supported
between driver and firmware. Also update bnxt.rst documentation file.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add definition and documentation for the new generic info
"fw.mgmt.api". This macro specifies the version of the software
interfaces between driver and firmware.
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Jacob Keller <jacob.e.keller@intel.com>
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ido Schimmel says:
====================
mlxsw: Various static checkers fixes
Jakub told me he gets some warnings with W=1, so I decided to check with
sparse, smatch and coccinelle as well. This patch set fixes all the
issues found. None are actual bugs / regressions and therefore not
targeted at net.
Patches #1-#2 add missing kernel-doc comments.
Patch #3 removes dead code.
Patch #4 reworks the ACL code to avoid defining a static variable in a
header file.
Patch #5 removes unnecessary conversion to bool that coccinelle warns
about.
Patch #6 avoids false-positive uninitialized symbol errors emitted by
smatch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Suppress the following smatch errors. None of these are actually
possible with current code paths.
drivers/net/ethernet/mellanox/mlxsw//spectrum_router.c:1220
mlxsw_sp_ipip_entry_find_decap() error: uninitialized symbol 'saddrp'.
drivers/net/ethernet/mellanox/mlxsw//spectrum_router.c:1220
mlxsw_sp_ipip_entry_find_decap() error: uninitialized symbol
'saddr_len'.
drivers/net/ethernet/mellanox/mlxsw//spectrum_router.c:1221
mlxsw_sp_ipip_entry_find_decap() error: uninitialized symbol
'saddr_prefix_len'.
drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:1390
mlxsw_sp_netdevice_ipip_ol_reg_event() error: uninitialized symbol
'ipipt'.
drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:3255
mlxsw_sp_nexthop_group_update() error: uninitialized symbol 'err'.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Suppress following warning from coccinelle:
drivers/net/ethernet/mellanox/mlxsw//switchx2.c:183:63-68: WARNING:
conversion to bool not needed here
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The static array 'mlxsw_afk_element_infos' in 'core_acl_flex_keys.h' is
copied to each file that includes the header, but not all use it. This
results in the following warnings when compiling with W=1:
drivers/net/ethernet/mellanox/mlxsw//core_acl_flex_keys.h:76:44:
warning: ‘mlxsw_afk_element_infos’ defined but not used
[-Wunused-const-variable=]
One way to suppress the warning is to mark the array with
'__maybe_unused', but another option is to remove it from the header
file entirely.
Change 'struct mlxsw_afk_element_inst' to store the key to the array
('element') instead of the array value keyed by 'element'. Adjust the
different users accordingly.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In merge commit 50853808ff4a ("Merge branch
'mlxsw-Prepare-for-VLAN-aware-bridge-w-VxLAN'") I flipped mlxsw to use
emulated 802.1Q FIDs and correspondingly emulated VLAN RIFs. This means
that the non-emulated variants are no longer used. Remove them and
suppress the following warnings when compiling with W=1:
drivers/net/ethernet/mellanox/mlxsw//spectrum_router.c:7572:38: warning:
‘mlxsw_sp_rif_vlan_ops’ defined but not used [-Wunused-const-variable=]
drivers/net/ethernet/mellanox/mlxsw//spectrum_fid.c:584:41: warning:
‘mlxsw_sp_fid_8021q_family’ defined but not used
[-Wunused-const-variable=]
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Suppress following warnings when compiling with W=1:
drivers/net/ethernet/mellanox/mlxsw//spectrum_router.c:1552: warning:
Function parameter or member 'mlxsw_sp' not described in
'__mlxsw_sp_ipip_entry_update_tunnel'
drivers/net/ethernet/mellanox/mlxsw//spectrum_router.c:1552: warning:
Function parameter or member 'ipip_entry' not described in
'__mlxsw_sp_ipip_entry_update_tunnel'
drivers/net/ethernet/mellanox/mlxsw//spectrum_router.c:1552: warning:
Function parameter or member 'extack' not described in
'__mlxsw_sp_ipip_entry_update_tunnel'
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Suppress following warning when compiling with W=1:
drivers/net/ethernet/mellanox/mlxsw//i2c.c:78: warning: Function
parameter or member 'cmd' not described in 'mlxsw_i2c'
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec
Steffen Klassert says:
====================
pull request (net): ipsec 2020-03-27
1) Handle NETDEV_UNREGISTER for xfrm device to handle asynchronous
unregister events cleanly. From Raed Salem.
2) Fix vti6 tunnel inter address family TX through bpf_redirect().
From Nicolas Dichtel.
3) Fix lenght check in verify_sec_ctx_len() to avoid a
slab-out-of-bounds. From Xin Long.
4) Add a missing verify_sec_ctx_len check in xfrm_add_acquire
to avoid a possible out-of-bounds to access. From Xin Long.
5) Use built-in RCU list checking of hlist_for_each_entry_rcu
to silence false lockdep warning in __xfrm6_tunnel_spi_lookup
when CONFIG_PROVE_RCU_LIST is enabled. From Madhuparna Bhowmik.
6) Fix a panic on esp offload when crypto is done asynchronously.
From Xin Long.
7) Fix a skb memory leak in an error path of vti6_rcv.
From Torsten Hilbrich.
8) Fix a race that can lead to a doulbe free in xfrm_policy_timer.
From Xin Long.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
