| Age | Commit message (Collapse) | Author |
|---|
|
Allocate higher order pages when pagesize is small, this will
reduce number of calls to page allocator and wastage of memory.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the case of OF device tree, the firmware information is attached to
the BGX device structure in the standard manner, so use the firmware
iterators and accessors where possible.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This affinity hint can be used by user space irqbalance tool to set
preferred CPU mask for irqs registered by this VF. Irqbalance needs
to be in 'exact' mode to set irq affinity same as indicated by
affinity hint.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
napi_schedule is being called from hard irq context, hence
switch to napi_schedule_irqoff which avoids unneeded call
to local_irq_save and local_irq_restore.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When system is low on atomic memory, too many error messages are logged.
Since this is not a total failure but a simple switch to non-atomic allocation
better to have a stat.
Also add a stat for reset, kicked due to transmit watchdog timeout.
Signed-off-by: Thanneeru Srinivasulu <tsrinivasulu@caviumnetworks.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When checking specific attribute from a bit mask, need to use bitwise
AND and not logical AND, fixed that.
Fixes: 145d9c541032 ('IB/core: Display extended counter set if
available')
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The while loop after err_slaves should use post-decrement; otherwise
we'll fail to do the kfrees for i==0, and will run into out-of-bounds
accesses if the setup above failed already at i==0.
[I'm not sure why one even bothers populating the ->vlan_filter array:
mlx4.h isn't #included by anything outside
drivers/net/ethernet/mellanox/mlx4/, and "git grep -C2 -w vlan_filter
drivers/net/ethernet/mellanox/mlx4/" seems to suggest that the
vlan_filter elements aren't used at all.]
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
If the LightNVM subsystem is not compiled into the kernel, and the
null_blk device driver requests lightnvm to be initialized. The call to
nvm_register fails and the null_add_dev function cleans up the
initialization. However, at this point the null block device has
already been added to the nullb_list and thus a second cleanup will
occur when the function has returned, that leads to a double call to
blk_cleanup_queue.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
This reverts commit 829b6962f7e3cfc06f7c5c26269fd47ad48cf503.
Revert this change as it causes a sysfs path to change and therefore
introduces and ABI regression. More precisely Android's vold is not being
able to access /sys/module/mmcblk/parameters/perdev_minors any more, since
the path becomes changed to: "/sys/module/mmc_block/..."
Fixes: 829b6962f7e3 ("mmc: block: don't use parameter prefix if built as
module")
Reported-by: John Stultz <john.stultz@linaro.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
In __cpufreq_cooling_register() we allocate the arrays for time_in_idle
and time_in_idle_timestamp to be as big as the number of cpus in this
cpufreq device. However, in get_load() we access this array using the
cpu number as index, which can result in an out of bound access.
Index time_in_idle{,_timestamp} using the index in the cpufreq_device's
allowed_cpus mask, as we do for the load_cpu array in
cpufreq_get_requested_power()
Reported-by: Nicolas Boichat <drinkcat@chromium.org>
Cc: Amit Daniel Kachhap <amit.kachhap@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
The value of ctx->pos in the last readdir call is supposed to be set to
INT_MAX due to 32bit compatibility, unless 'pos' is intentially set to a
larger value, then it's LLONG_MAX.
There's a report from PaX SIZE_OVERFLOW plugin that "ctx->pos++"
overflows (https://forums.grsecurity.net/viewtopic.php?f=1&t=4284), on a
64bit arch, where the value is 0x7fffffffffffffff ie. LLONG_MAX before
the increment.
We can get to that situation like that:
* emit all regular readdir entries
* still in the same call to readdir, bump the last pos to INT_MAX
* next call to readdir will not emit any entries, but will reach the
bump code again, finds pos to be INT_MAX and sets it to LLONG_MAX
Normally this is not a problem, but if we call readdir again, we'll find
'pos' set to LLONG_MAX and the unconditional increment will overflow.
The report from Victor at
(http://thread.gmane.org/gmane.comp.file-systems.btrfs/49500) with debugging
print shows that pattern:
Overflow: e
Overflow: 7fffffff
Overflow: 7fffffffffffffff
PAX: size overflow detected in function btrfs_real_readdir
fs/btrfs/inode.c:5760 cicus.935_282 max, count: 9, decl: pos; num: 0;
context: dir_context;
CPU: 0 PID: 2630 Comm: polkitd Not tainted 4.2.3-grsec #1
Hardware name: Gigabyte Technology Co., Ltd. H81ND2H/H81ND2H, BIOS F3 08/11/2015
ffffffff81901608 0000000000000000 ffffffff819015e6 ffffc90004973d48
ffffffff81742f0f 0000000000000007 ffffffff81901608 ffffc90004973d78
ffffffff811cb706 0000000000000000 ffff8800d47359e0 ffffc90004973ed8
Call Trace:
[<ffffffff81742f0f>] dump_stack+0x4c/0x7f
[<ffffffff811cb706>] report_size_overflow+0x36/0x40
[<ffffffff812ef0bc>] btrfs_real_readdir+0x69c/0x6d0
[<ffffffff811dafc8>] iterate_dir+0xa8/0x150
[<ffffffff811e6d8d>] ? __fget_light+0x2d/0x70
[<ffffffff811dba3a>] SyS_getdents+0xba/0x1c0
Overflow: 1a
[<ffffffff811db070>] ? iterate_dir+0x150/0x150
[<ffffffff81749b69>] entry_SYSCALL_64_fastpath+0x12/0x83
The jump from 7fffffff to 7fffffffffffffff happens when new dir entries
are not yet synced and are processed from the delayed list. Then the code
could go to the bump section again even though it might not emit any new
dir entries from the delayed list.
The fix avoids entering the "bump" section again once we've finished
emitting the entries, both for synced and delayed entries.
References: https://forums.grsecurity.net/viewtopic.php?f=1&t=4284
Reported-by: Victor <services@swwu.com>
CC: stable@vger.kernel.org
Signed-off-by: David Sterba <dsterba@suse.com>
Tested-by: Holger Hoffstätte <holger.hoffstaette@googlemail.com>
Signed-off-by: Chris Mason <clm@fb.com>
|
|
Nikolay Borisov says:
====================
Make igmp sysctl knobs namespace aware
This series continue making more of the net related sysctls
namespace aware. The first 2 and last patches are straight
forward and convert sysctls which weren't defined to be
namespace aware. The only thing in them is that each removes
a define which is used in only one place (to initialise
the respective sysctl) so I don't think this is a huge loss.
The third patch however, converts igmp_llm_reports which was
already defined in the ipv4_net_table but wasn't using any of
the net namespace infrastructure.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Nikolay Borisov <kernel@kyup.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This was initially introduced in df2cf4a78e488d26 ("IGMP: Inhibit
reports for local multicast groups") by defining the sysctl in the
ipv4_net_table array, however it was never implemented to be
namespace aware. Fix this by changing the code accordingly.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Nikolay Borisov <kernel@kyup.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Nikolay Borisov <kernel@kyup.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace 'goto' with 'return' to remove unnecessary check at label:
err_undo_flags.
The reason is that 'err_undo_flags' do two things for the first slave device:
1.revert bond mac address if it is set by the slave device.
2.revert bond device type if it's not ARPHRD_ETHER.
It's not necessary for the following three places, they changed neither bond
mac address nor type. It's straightforward to return directly.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tested on Acqua A5 SoM (http://www.acmesystems.it/acqua).
Signed-off-by: Sergio Prado <sergio.prado@e-labworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
32 bit systems using 'struct timeval' will break in the year 2038, so
we replace the code appropriately. However, this driver is not broken
in 2038 since we are only using microseconds portion of the time.
This patch replaces 'struct timeval' with 'struct timespec64'. We only
need to find elapsed microseconds rather than absolute time, so it's
better to use monotonic time, so using ktime_get_ts64() makes the code
more efficient and more robust against concurrent settimeofday()
calls.
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Thomas Sailer <t.sailer@alumni.ethz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Operations with the GENL_ADMIN_PERM flag fail permissions checks because
this flag means we call netlink_capable, which uses the init user ns.
Instead, let's introduce a new flag, GENL_UNS_ADMIN_PERM for operations
which should be allowed inside a user namespace.
The motivation for this is to be able to run openvswitch in unprivileged
containers. I've tested this and it seems to work, but I really have no
idea about the security consequences of this patch, so thoughts would be
much appreciated.
v2: use the GENL_UNS_ADMIN_PERM flag instead of a check in each function
v3: use separate ifs for UNS_ADMIN_PERM and ADMIN_PERM, instead of one
massive one
Reported-by: James Page <james.page@canonical.com>
Signed-off-by: Tycho Andersen <tycho.andersen@canonical.com>
CC: Eric Biederman <ebiederm@xmission.com>
CC: Pravin Shelar <pshelar@ovn.org>
CC: Justin Pettit <jpettit@nicira.com>
CC: "David S. Miller" <davem@davemloft.net>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Many virtual and not quite virtual devices allow any speed to be set
through ethtool. In particular, this applies to the virtio-net devices.
Document this fact to make sure people don't assume the enum lists all
possible values. Reserve values greater than INT_MAX for future
extension and to avoid conflict with SPEED_UNKNOWN.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Duplicate include detected.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The return value of kzalloc on failure of allocation of memory should
be -ENOMEM and not -1.
Found using Coccinelle. A simplified version of the semantic patch
used is:
//<smpl>
@@
expression *e;
@@
e = kzalloc(...);
if (e == NULL) {
...
return
- -1
+ -ENOMEM
;
}
//</smpl>
The single call site only checks that the return value is not 0,
hence no change is required at the call site.
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the dawn of time the ICST code has only supported divide
by one or hang in an eternal loop. Luckily we were always dividing
by one because the reference frequency for the systems using
the ICSTs is 24MHz and the [min,max] values for the PLL input
if [10,320] MHz for ICST307 and [6,200] for ICST525, so the loop
will always terminate immediately without assigning any divisor
for the reference frequency.
But for the code to make sense, let's insert the missing i++
Reported-by: David Binderman <dcb314@hotmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Alexander Duyck says:
====================
Add GSO support for outer checksum w/ inner checksum offloads
This patch series updates the existing segmentation offload code for
tunnels to make better use of existing and updated GSO checksum
computation. This is done primarily through two mechanisms. First we
maintain a separate checksum in the GSO context block of the sk_buff. This
allows us to maintain two checksum values, one offloaded with values stored
in csum_start and csum_offset, and one computed and tracked in
SKB_GSO_CB(skb)->csum. By maintaining these two values we are able to take
advantage of the same sort of math used in local checksum offload so that
we can provide both inner and outer checksums with minimal overhead.
Below is the performance for a netperf session between an ixgbe PF and VF
on the same host but in different namespaces. As can be seen a significant
gain in performance can be had from allowing the use of Tx checksum offload
on the inner headers while performing a software offload on the outer
header computation:
Recv Send Send Utilization Service Demand
Socket Socket Message Elapsed Send Recv Send Recv
Size Size Size Time Throughput local remote local remote
bytes bytes bytes secs. 10^6bits/s % S % U us/KB us/KB
Before:
87380 16384 16384 10.00 12844.38 9.30 -1.00 0.712 -1.00
After:
87380 16384 16384 10.00 13216.63 6.78 -1.00 0.504 -1.000
Changes from v1:
* Dropped use of CHECKSUM_UNNECESSARY for remote checksum offload
* Left encap_hdr_csum as it will likely be needed in future for SCTP GSO
* Broke the changes out over many more patches
* Updated GRE segmentation to more closely match UDP tunnel segmentation
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch enables us to use inner checksum offloads if provided by
hardware with outer checksums computed by software.
It basically reduces encap_hdr_csum to an advisory flag for now, but based
on the fact that SCTP may be getting segmentation support before long I
thought we may want to keep it as it is possible we may need to support
CRC32c and 1's compliment checksum in the same packet at some point in the
future.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The segmentation code was having to do a bunch of work to pull the
skb->len and strip the udp header offset before the value could be used to
adjust the checksum. Instead of doing all this work we can just use the
value that goes into uh->len since that is the correct value with the
correct byte order that we need anyway. By using this value we can save
ourselves a bunch of pain as there is no need to do multiple byte swaps.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch goes though and cleans up the logic related to several of the
control flags used in UDP segmentation. Specifically the use of dont_encap
isn't really needed as we can just check the skb for CHECKSUM_PARTIAL and
if it isn't set then we don't need to update the internal headers. As such
we can just drop that value.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of parsing headers to determine the inner protocol we can just pull
the value from inner_proto.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch updates the gre checksum path to follow something much closer to
the UDP checksum path. By doing this we can avoid needing to do as much
header inspection and can just make use of the fields we were already
reading in the sk_buff structure.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The call skb_has_shared_frag is used in the GRE path and skb_checksum_help
to verify that no frags can be modified by an external entity. This check
really doesn't belong in the GRE path but in the skb_segment function
itself. This way any protocol that might be segmented will be performing
this check before attempting to offload a checksum to software.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch makes it so that we can offload the checksums for a packet up
to a certain point and then begin computing the checksums via software.
Setting this up is fairly straight forward as all we need to do is reset
the values stored in csum and csum_start for the GSO context block.
One complication for this is remote checksum offload. In order to allow
the inner checksums to be offloaded while computing the outer checksum
manually we needed to have some way of indicating that the offload wasn't
real. In order to do that I replaced CHECKSUM_PARTIAL with
CHECKSUM_UNNECESSARY in the case of us computing checksums for the outer
header while skipping computing checksums for the inner headers. We clean
up the ip_summed flag and set it to either CHECKSUM_PARTIAL or
CHECKSUM_NONE once we hand the packet off to the next lower level.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch addresses two main issues.
First in the case of remote checksum offload we were avoiding dealing with
scatter-gather issues. As a result it would be possible to assemble a
series of frames that used frags instead of being linearized as they should
have if remote checksum offload was enabled.
Second I have updated the code so that we now let GSO take care of doing
the checksum on the data itself and drop the special case that was added
for remote checksum offload.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch moves the checksum maintained by GSO out of skb->csum and into
the GSO context block in order to allow for us to work on outer checksums
while maintaining the inner checksum offsets in the case of the inner
checksum being offloaded, while the outer checksums will be computed.
While updating the code I also did a minor cleanu-up on gso_make_checksum.
The change is mostly to make it so that we store the values and compute the
checksum instead of computing the checksum and then storing the values we
needed to update.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The enc_features variable isn't necessary since features isn't used
anywhere after we create enc_features so instead just use a destructive AND
on features itself and save ourselves the variable declaration.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It seems that on H3, just like on A10, when GPIOs are configured as
external interrupt data registers does not contain their value. When
value is read, GPIO function must be temporary switched to input for
reads.
Signed-off-by: Krzysztof Adamski <k@japko.eu>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Setting TCR_EL2.PS to 40 bits is wrong on systems with less that
less than 40 bits of physical addresses. and breaks KVM on systems
where the RAM is above 40 bits.
This patch uses ID_AA64MMFR0_EL1.PARange to set TCR_EL2.PS dynamically,
just like we already do for VTCR_EL2.PS.
[Marc: rewrote commit message, patch tidy up]
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Tirumalesh Chalamarla <tchalamarla@caviumnetworks.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
1. Adding NETIF_F_TSO6 feature flag;
2. Adding NETIF_F_HW_CSUM. NETIF_F_IPV6_CSUM and NETIF_F_IP_CSUM are
being deprecated;
3. Cleanup the coding style of flag assignment by using macro.
Signed-off-by: Simon Xiao <sixiao@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Edward Cree says:
====================
IPv6 NFC
This series adds support for steering IPv6 flows using the ethtool NFC
interface, and implements it for sfc devices.
Tested using an in-development patch to the ethtool utility.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Edward Cree <ecree@solarflare.com>
Reviewed-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Edward Cree <ecree@solarflare.com>
Reviewed-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hariprasad Shenai says:
====================
Add TOS support and some cleanup
This series adds TOS support for iWARP and also does some cleanup to make
code more readable. Patch series is created against infiniband tree and
includes patches on iw_cxgb4 and cxgb4 driver.
We have included all the maintainers of respective drivers. Kindly review
the change and let us know in case of any review comments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This series provides support for iWARP applications to specify a TOS
value and have that map to a VLAN Priority for iw_cxgb4 iWARP connections.
In iw_cxgb4, when allocating an L2T entry, pass the skb_priority based
on the tos value in the cm_id. Also pass the correct tos value during
connection setup so the passive side gets the client's desired tos.
When sending the FLOWC work request to FW, if the egress device is
in a vlan, then use the vlan priority bits as the scheduling class.
This allows associating RDMA connections with scheduling classes to
provide traffic shaping per flow.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't log errors if a listening endpoint is going away when procesing a
PASS_ACCEPT_REQ message. This can happen. Change the error printk to
a PDBG() debug log entry
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rename local mm* variables to more meaningful names
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The diagnose tracer will indirectly call back into the lockdep code
when lockdep does not expect it (arch_spinlock). This causes lockdep
to disable itself and therefore we don't have a working lock
dependency validator anymore.
This patch effectively disables tracing of diag 0x9c and 0x44 if
lockdep is enabled. If however lockdep is enabled spinlocks are
mainly implemented using a trylock variant, which will not issue any
diag 0x9c or 0x44. So this change has hardly any effect on tracing
except when arch_spinlock and friends are explicitly used.
Reported-and-Tested-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Add refcount to the DASD device when a summary unit check worker is
scheduled. This prevents that the device is set offline with worker
in place.
Cc: stable@vger.kernel.org
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
